?>/script>'; } ?> [Desarrollo] OpenWrt en Huawei HG556a Widgets Magazine
« anterior próximo »
Páginas: 1 ... 37 38 39 40 41 42 43 [44] 45 46 47 48 49 50 51 ... 156   Ir Abajo

Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a  (Leído 2124591 veces)

0 Usuarios y 1 Visitante están viendo este tema.

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: OpenWRT en Huawei hg556a
« Respuesta #860 en: 02-11-2012, 15:03 (Viernes) »
Pues hazlo como te he puesto a ver si te da el mismo error.
En línea

franrg1

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #861 en: 02-11-2012, 15:11 (Viernes) »
Cita de: jar229 en 02-11-2012, 15:03 (Viernes)
Pues hazlo como te he puesto a ver si te da el mismo error.

Esto me sale:

Código: [Seleccionar]
root@OpenWrt:~# mount -t vfat /dev/sda1 /mnt/usb -o rw,sync
mount: mounting /dev/sda1 on /mnt/usb failed: Invalid argument

He creado /mnt/usb para hacerlo exactamente como me has dicho, pero no hay manera  :(

Un saludo y gracias
En línea

peterpunk

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #862 en: 02-11-2012, 16:11 (Viernes) »
Lo has desmontado previamente?
Si se ha montado de una manera, no entiendo q no se monte en otro dir.
En línea

franrg1

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #863 en: 02-11-2012, 16:15 (Viernes) »
Cita de: peterpunk en 02-11-2012, 16:11 (Viernes)
Lo has desmontado previamente?
Si se ha montado de una manera, no entiendo q no se monte en otro dir.


No no, quería decir que lo había intentado montar en /USB, pero no lo he conseguido. Y no lo he desmontado porque no está montado

Un saludo y gracias
En línea

peterpunk

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #864 en: 02-11-2012, 17:22 (Viernes) »
Me da que es el mismo problema que tuve yo.
Por favor.

verifica el dmesg que no existen errores.

que tienes instalados los paquetes:

kmod-nls-cp437
kmod-nls-iso8859-1

Si no estan:
opkg install --force-depend kmod-nls-cp437
opkg install --force-depend kmod-nls-iso8859-1

y prueba a montar de nuevo.
Respasa este post:
https://foro.seguridadwireless.net/openwrt/convertir-tdt-en-centro-multimedia-wifi-con-router-hg556a/

En línea

peterpunk

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #865 en: 02-11-2012, 18:24 (Viernes) »
Cita de: jar229 en 02-11-2012, 14:15 (Viernes)

Para los nuevos (que nadie se lo tome a mal), repasaros los hilos fijos que hay en el subforo de OpenWrt. Preguntáis muchas cosas que ya están respondidas.

Hola
con todo el respeto del mundo, y mas sabiendo que estas haciendo unmuy buen trabajo, pero hecho en falta que en la primera parte del post una notas generales que se repiten a lo largo de las 40 paginas de este post entre ellas:

- El tema de actualizar los paquetes, hay que cambiar la dir de descarga.
- Montar los discos usb, sobre todo los paquetes que faltan.
- El cambio del dir de la impresara.
- Es escaner,  le tengo montado, pero como alguien tenga que montarlo ahora tiene que repasar las 40 paginas.

Supongo que se me olvidan muchas cosas.
Pido de nuevo disculpas por si ofende. Pero no se puede leer uno todos los mensajes para montar un disco.

Saludos
En línea

peterpunk

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #866 en: 02-11-2012, 18:32 (Viernes) »
¿Alguien ha conseguido imprimir con el Android a traves del router?

Por si no me he explicado.
Tengo una impresora antigua no WIFI. La conecto por USB al router y configuro con Windows y puedo imprimir. Tengo una impresora Wifi.

Algun programita para poder imprimir desde Android. No encuentro un programa que me permita crear un puerto TCP/IP, para poder utilizar el servidor de impresión del router.

No entiendo que para un scaner no tenga que hacer nada mas que darle la ip y para un impresora no haya manera de configurarla.
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: Re: Re: OpenWRT en Huawei hg556a
« Respuesta #867 en: 02-11-2012, 19:10 (Viernes) »
Cita de: peterpunk en 02-11-2012, 18:24 (Viernes)

Hola
con todo el respeto del mundo, y mas sabiendo que estas haciendo unmuy buen trabajo, pero hecho en falta que en la primera parte del post una notas generales que se repiten a lo largo de las 40 paginas de este post entre ellas:

- El tema de actualizar los paquetes, hay que cambiar la dir de descarga.
- Montar los discos usb, sobre todo los paquetes que faltan.
- El cambio del dir de la impresara.
- Es escaner,  le tengo montado, pero como alguien tenga que montarlo ahora tiene que repasar las 40 paginas.

Supongo que se me olvidan muchas cosas.
Pido de nuevo disculpas por si ofende. Pero no se puede leer uno todos los mensajes para montar un disco.

Saludos

No hace falta leerse 40 páginas (aunque lo cierto es que para aprender hay que leer, no queda otra). Con usar el botón de buscar es suficiente ;D

Sobre la impresión desde Android, busca en google play PrintHand mobile. No lo he probado así que no tengo ni idea de si funcionará ....

Enviado desde mi Cube U30GT ( Infected v. 1.3) usando Tapatalk 2
En línea

franrg1

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #868 en: 02-11-2012, 21:19 (Viernes) »
Cita de: peterpunk en 02-11-2012, 17:22 (Viernes)
Me da que es el mismo problema que tuve yo.
Por favor.

verifica el dmesg que no existen errores.

que tienes instalados los paquetes:

kmod-nls-cp437
kmod-nls-iso8859-1

Si no estan:
opkg install --force-depend kmod-nls-cp437
opkg install --force-depend kmod-nls-iso8859-1

y prueba a montar de nuevo.
Respasa este post:
https://foro.seguridadwireless.net/openwrt/convertir-tdt-en-centro-multimedia-wifi-con-router-hg556a/



Gracias a todos por la ayuda.

Como dije en el primer post, necesito montar el usb porque no tendría conexión a internet y querría instalar paquetes desde este. Por lo que si tengo que instalar los paquetes que dices, no lo podría hacer.

La otra solución que se me ocurre es cambiar de formato el pen, a uno que sea soportado directamente por el sistema, sin tener que agregar paquetes. ¿Hay algún formato?


Un saludo!
En línea

franrg1

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #869 en: 02-11-2012, 21:34 (Viernes) »
Al final he cambiado el formato a NTFS y me lo reconoce sin problemas  >:(

Así que todo correcto!

Un saludo y gracias a todos
En línea

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #870 en: 06-11-2012, 20:41 (Martes) »
Ya me ha llegado el Huawei HG556a. Me ha tocado un atheros ^^.

He probado unos parches nuevos que voy a ir mandando poco a poco en mi hg556a, pero me gustaría algo de feedback por parte de alguien con la versión ralink.

https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r33935.bin

Necesito un dmesg:
dmesg > /www/dmesg.txt
En el PC:
http://192.168.1.8/dmesg.txt

Saludos!
« Última modificación: 07-11-2012, 01:30 (Miércoles) por Noltari »
En línea

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #871 en: 07-11-2012, 12:09 (Miércoles) »
Parche del "endian_check" necesario para el cal_data de los routers atheros integrado en openwrt.

https://dev.openwrt.org/changeset/34105
https://github.com/Noltari/openwrt/commit/d336a6138478a3cf77ad8b12fa519b9048a8c595

No es que sea un parche muy complicado, pero sí necesario para tener wifi en los router atheros ^^.
Voy a ir mandando los parches necesarios para el HG556a de uno en uno, ya que mi experiencia me dice que es mejor, porque luego hay que cambiar un parche y afecta a todos los que van detrás xDDD.

Por cierto, cuanto antes pueda conseguir feedback de un router ralink con el firmware que puse antes mejor, porque es de los parches siguientes que voy a enviar a openwrt (justo después del parche del pin del wifi en los atheros).

Saludos!
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: OpenWRT en Huawei hg556a
« Respuesta #872 en: 07-11-2012, 20:31 (Miércoles) »
Ya irás contando la evolución de los parches  ;)

Me alegro que te 'tocara' uno con atheros  >:(
En línea

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #873 en: 07-11-2012, 20:47 (Miércoles) »
Cita de: jar229 en 07-11-2012, 20:31 (Miércoles)
Ya irás contando la evolución de los parches  ;)

Me alegro que te 'tocara' uno con atheros  >:(
De momento ya he enviado el del led_pin. Cuando me lo acepten tocaría el del pci fixup de los ralink, pero si no recibo feedback de alguien con un router ralink diciendo que funciona, se para todo :$...
« Última modificación: 08-11-2012, 13:09 (Jueves) por Noltari »
En línea

Bastinazo

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #874 en: 08-11-2012, 12:57 (Jueves) »
Vamos esos "ralinkeros" Noltari os necesita  y los "athereros" también  ;D
En línea

danitool

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #875 en: 08-11-2012, 13:31 (Jueves) »
Yo también me sumo al llamamiento de los ralinkeros  >:(
En línea

Desconectado geminis_demon

  • Colaborador
  • *
  • Mensajes: 2378
  • Prácticas precisas precisan práctica
Re: OpenWRT en Huawei hg556a
« Respuesta #876 en: 08-11-2012, 13:41 (Jueves) »
Aquí un ralinkero, voy a bajar la compilación y en unos minutos posteo los resultados.

Pues aquí está el dmsg:

[spoiler=dmesg]
Código: [Seleccionar]
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #3 Tue Nov 6 20:12:59 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802a5b10, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61720k/65536k available (2238k kernel code, 3816k reserved, 409k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] PCI: CLS 0 bytes, default 16
[    0.196000] audit: initializing netlink socket (disabled)
[    0.204000] type=2000 audit(0.204:1): initialized
[    0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.268000] physmap platform flash device: 02000000 at 1e000000
[    0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.288000]   Amd/Fujitsu Extended Query version 1.3.
[    0.296000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.328000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.348000] bcm63xxpart: Spare partition is offset 3a0004 and length b3fffc
[    0.356000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.364000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.368000] 0x000000000000-0x000000020000 : "CFE"
[    0.380000] 0x000000020100-0x000000120000 : "kernel"
[    0.384000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.408000] mtd: partition "rootfs" set to be root filesystem
[    0.416000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=B40000
[    0.424000] 0x0000003a0000-0x000000ee0000 : "rootfs_data"
[    0.432000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.444000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.452000] 0x000000020000-0x000000ee0000 : "linux"
[    0.472000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.480000] Registered led device: HW556:red:message
[    0.480000] Registered led device: HW556:red:hspa
[    0.480000] Registered led device: HW556:red:dsl
[    0.484000] Registered led device: HW556:red:power
[    0.484000] Registered led device: HW556:red:all
[    0.484000] TCP cubic registered
[    0.488000] NET: Registered protocol family 17
[    0.492000] 8021q: 802.1Q VLAN Support v1.8
[    0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.516000] Freeing unused kernel memory: 208k freed
[    3.284000] eth0: link forced UP - 100/full - flow control off/off
[    3.544000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.612000] There is already a switch registered on the device 'eth0'
[    6.076000] Button Hotplug driver version 0.4.1
[    6.112000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   13.416000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.424000] Backport based on wireless-testing.git master-2012-09-07
[   13.428000] compat.git: wireless-testing.git
[   13.492000] cfg80211: Calling CRDA to update world regulatory domain
[   13.500000] cfg80211: World regulatory domain updated:
[   13.504000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.516000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.524000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.532000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.540000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.548000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.000000] NET: Registered protocol family 10
[   14.492000] SCSI subsystem initialized
[   14.588000] There is already a switch registered on the device 'eth0'
[   14.856000] usbcore: registered new interface driver usbfs
[   14.860000] usbcore: registered new interface driver hub
[   14.868000] usbcore: registered new device driver usb
[   16.096000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.100000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.416000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.420000] Registered led device: rt2800pci-phy0::radio
[   16.420000] Registered led device: rt2800pci-phy0::assoc
[   16.420000] Registered led device: rt2800pci-phy0::quality
[   17.784000] PPP generic driver version 2.4.2
[   18.188000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] NET: Registered protocol family 24
[   18.892000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.004000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.008000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.044000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.060000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.068000] hub 1-0:1.0: USB hub found
[   19.072000] hub 1-0:1.0: 2 ports detected
[   19.128000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
[   20.268000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   20.700000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.812000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.816000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.824000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.892000] hub 2-0:1.0: USB hub found
[   20.896000] hub 2-0:1.0: 1 port detected
[   21.104000] Initializing USB Mass Storage driver...
[   21.108000] usbcore: registered new interface driver usb-storage
[   21.116000] USB Mass Storage support registered.
[   21.300000] usbcore: registered new interface driver ums-alauda
[   21.340000] usbcore: registered new interface driver ums-cypress
[   21.380000] usbcore: registered new interface driver ums-datafab
[   21.420000] usbcore: registered new interface driver ums-freecom
[   21.456000] usbcore: registered new interface driver ums-isd200
[   21.496000] usbcore: registered new interface driver ums-jumpshot
[   21.532000] usbcore: registered new interface driver ums-karma
[   21.572000] usbcore: registered new interface driver ums-sddr09
[   21.612000] usbcore: registered new interface driver ums-sddr55
[   21.652000] usbcore: registered new interface driver ums-usbat
[   21.732000] fuse init (API version 7.18)
[   27.616000] eth0: link forced UP - 100/full - flow control off/off
[   27.632000] device eth0 entered promiscuous mode
[   27.640000] br-lan: port 1(eth0) entered forwarding state
[   27.644000] br-lan: port 1(eth0) entered forwarding state
[   29.648000] br-lan: port 1(eth0) entered forwarding state
[   52.724000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   52.736000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   52.740000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  118.564000] JFFS2 notice: (1118) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler]
« Última modificación: 08-11-2012, 14:09 (Jueves) por geminis_demon »
En línea

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #877 en: 08-11-2012, 14:22 (Jueves) »
Cita de: geminis_demon en 08-11-2012, 13:41 (Jueves)
Aquí un ralinkero, voy a bajar la compilación y en unos minutos posteo los resultados.

Pues aquí está el dmsg:

[spoiler=dmesg]
Código: [Seleccionar]
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #3 Tue Nov 6 20:12:59 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802a5b10, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61720k/65536k available (2238k kernel code, 3816k reserved, 409k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] PCI: CLS 0 bytes, default 16
[    0.196000] audit: initializing netlink socket (disabled)
[    0.204000] type=2000 audit(0.204:1): initialized
[    0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.268000] physmap platform flash device: 02000000 at 1e000000
[    0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.288000]   Amd/Fujitsu Extended Query version 1.3.
[    0.296000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.328000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.348000] bcm63xxpart: Spare partition is offset 3a0004 and length b3fffc
[    0.356000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.364000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.368000] 0x000000000000-0x000000020000 : "CFE"
[    0.380000] 0x000000020100-0x000000120000 : "kernel"
[    0.384000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.408000] mtd: partition "rootfs" set to be root filesystem
[    0.416000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=B40000
[    0.424000] 0x0000003a0000-0x000000ee0000 : "rootfs_data"
[    0.432000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.444000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.452000] 0x000000020000-0x000000ee0000 : "linux"
[    0.472000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.480000] Registered led device: HW556:red:message
[    0.480000] Registered led device: HW556:red:hspa
[    0.480000] Registered led device: HW556:red:dsl
[    0.484000] Registered led device: HW556:red:power
[    0.484000] Registered led device: HW556:red:all
[    0.484000] TCP cubic registered
[    0.488000] NET: Registered protocol family 17
[    0.492000] 8021q: 802.1Q VLAN Support v1.8
[    0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.516000] Freeing unused kernel memory: 208k freed
[    3.284000] eth0: link forced UP - 100/full - flow control off/off
[    3.544000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.612000] There is already a switch registered on the device 'eth0'
[    6.076000] Button Hotplug driver version 0.4.1
[    6.112000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   13.416000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.424000] Backport based on wireless-testing.git master-2012-09-07
[   13.428000] compat.git: wireless-testing.git
[   13.492000] cfg80211: Calling CRDA to update world regulatory domain
[   13.500000] cfg80211: World regulatory domain updated:
[   13.504000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.516000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.524000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.532000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.540000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.548000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.000000] NET: Registered protocol family 10
[   14.492000] SCSI subsystem initialized
[   14.588000] There is already a switch registered on the device 'eth0'
[   14.856000] usbcore: registered new interface driver usbfs
[   14.860000] usbcore: registered new interface driver hub
[   14.868000] usbcore: registered new device driver usb
[   16.096000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.100000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.416000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.420000] Registered led device: rt2800pci-phy0::radio
[   16.420000] Registered led device: rt2800pci-phy0::assoc
[   16.420000] Registered led device: rt2800pci-phy0::quality
[   17.784000] PPP generic driver version 2.4.2
[   18.188000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] NET: Registered protocol family 24
[   18.892000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.004000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.008000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.044000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.060000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.068000] hub 1-0:1.0: USB hub found
[   19.072000] hub 1-0:1.0: 2 ports detected
[   19.128000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
[   20.268000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   20.700000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.812000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.816000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.824000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.892000] hub 2-0:1.0: USB hub found
[   20.896000] hub 2-0:1.0: 1 port detected
[   21.104000] Initializing USB Mass Storage driver...
[   21.108000] usbcore: registered new interface driver usb-storage
[   21.116000] USB Mass Storage support registered.
[   21.300000] usbcore: registered new interface driver ums-alauda
[   21.340000] usbcore: registered new interface driver ums-cypress
[   21.380000] usbcore: registered new interface driver ums-datafab
[   21.420000] usbcore: registered new interface driver ums-freecom
[   21.456000] usbcore: registered new interface driver ums-isd200
[   21.496000] usbcore: registered new interface driver ums-jumpshot
[   21.532000] usbcore: registered new interface driver ums-karma
[   21.572000] usbcore: registered new interface driver ums-sddr09
[   21.612000] usbcore: registered new interface driver ums-sddr55
[   21.652000] usbcore: registered new interface driver ums-usbat
[   21.732000] fuse init (API version 7.18)
[   27.616000] eth0: link forced UP - 100/full - flow control off/off
[   27.632000] device eth0 entered promiscuous mode
[   27.640000] br-lan: port 1(eth0) entered forwarding state
[   27.644000] br-lan: port 1(eth0) entered forwarding state
[   29.648000] br-lan: port 1(eth0) entered forwarding state
[   52.724000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   52.736000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   52.740000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  118.564000] JFFS2 notice: (1118) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler]
Tienes wifi sin problemas, verdad?

Si puedes ejecuta el siguiente comando y pon el resultado:
Código: [Seleccionar]
ls /lib/firmware
Saludos y muchas gracias por la prueba!
En línea

Desconectado geminis_demon

  • Colaborador
  • *
  • Mensajes: 2378
  • Prácticas precisas precisan práctica
Re: OpenWRT en Huawei hg556a
« Respuesta #878 en: 08-11-2012, 14:36 (Jueves) »
Cita de: Noltari en 08-11-2012, 14:22 (Jueves)
Cita de: geminis_demon en 08-11-2012, 13:41 (Jueves)
Aquí un ralinkero, voy a bajar la compilación y en unos minutos posteo los resultados.

Pues aquí está el dmsg:

[spoiler=dmesg]
Código: [Seleccionar]
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #3 Tue Nov 6 20:12:59 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802a5b10, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61720k/65536k available (2238k kernel code, 3816k reserved, 409k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] PCI: CLS 0 bytes, default 16
[    0.196000] audit: initializing netlink socket (disabled)
[    0.204000] type=2000 audit(0.204:1): initialized
[    0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.268000] physmap platform flash device: 02000000 at 1e000000
[    0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.288000]   Amd/Fujitsu Extended Query version 1.3.
[    0.296000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.328000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.348000] bcm63xxpart: Spare partition is offset 3a0004 and length b3fffc
[    0.356000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.364000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.368000] 0x000000000000-0x000000020000 : "CFE"
[    0.380000] 0x000000020100-0x000000120000 : "kernel"
[    0.384000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.408000] mtd: partition "rootfs" set to be root filesystem
[    0.416000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=B40000
[    0.424000] 0x0000003a0000-0x000000ee0000 : "rootfs_data"
[    0.432000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.444000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.452000] 0x000000020000-0x000000ee0000 : "linux"
[    0.472000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.480000] Registered led device: HW556:red:message
[    0.480000] Registered led device: HW556:red:hspa
[    0.480000] Registered led device: HW556:red:dsl
[    0.484000] Registered led device: HW556:red:power
[    0.484000] Registered led device: HW556:red:all
[    0.484000] TCP cubic registered
[    0.488000] NET: Registered protocol family 17
[    0.492000] 8021q: 802.1Q VLAN Support v1.8
[    0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.516000] Freeing unused kernel memory: 208k freed
[    3.284000] eth0: link forced UP - 100/full - flow control off/off
[    3.544000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.612000] There is already a switch registered on the device 'eth0'
[    6.076000] Button Hotplug driver version 0.4.1
[    6.112000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   13.416000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.424000] Backport based on wireless-testing.git master-2012-09-07
[   13.428000] compat.git: wireless-testing.git
[   13.492000] cfg80211: Calling CRDA to update world regulatory domain
[   13.500000] cfg80211: World regulatory domain updated:
[   13.504000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.516000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.524000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.532000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.540000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.548000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.000000] NET: Registered protocol family 10
[   14.492000] SCSI subsystem initialized
[   14.588000] There is already a switch registered on the device 'eth0'
[   14.856000] usbcore: registered new interface driver usbfs
[   14.860000] usbcore: registered new interface driver hub
[   14.868000] usbcore: registered new device driver usb
[   16.096000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.100000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.416000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.420000] Registered led device: rt2800pci-phy0::radio
[   16.420000] Registered led device: rt2800pci-phy0::assoc
[   16.420000] Registered led device: rt2800pci-phy0::quality
[   17.784000] PPP generic driver version 2.4.2
[   18.188000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] NET: Registered protocol family 24
[   18.892000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.004000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.008000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.044000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.060000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.068000] hub 1-0:1.0: USB hub found
[   19.072000] hub 1-0:1.0: 2 ports detected
[   19.128000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
[   20.268000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   20.700000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.812000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.816000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.824000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.892000] hub 2-0:1.0: USB hub found
[   20.896000] hub 2-0:1.0: 1 port detected
[   21.104000] Initializing USB Mass Storage driver...
[   21.108000] usbcore: registered new interface driver usb-storage
[   21.116000] USB Mass Storage support registered.
[   21.300000] usbcore: registered new interface driver ums-alauda
[   21.340000] usbcore: registered new interface driver ums-cypress
[   21.380000] usbcore: registered new interface driver ums-datafab
[   21.420000] usbcore: registered new interface driver ums-freecom
[   21.456000] usbcore: registered new interface driver ums-isd200
[   21.496000] usbcore: registered new interface driver ums-jumpshot
[   21.532000] usbcore: registered new interface driver ums-karma
[   21.572000] usbcore: registered new interface driver ums-sddr09
[   21.612000] usbcore: registered new interface driver ums-sddr55
[   21.652000] usbcore: registered new interface driver ums-usbat
[   21.732000] fuse init (API version 7.18)
[   27.616000] eth0: link forced UP - 100/full - flow control off/off
[   27.632000] device eth0 entered promiscuous mode
[   27.640000] br-lan: port 1(eth0) entered forwarding state
[   27.644000] br-lan: port 1(eth0) entered forwarding state
[   29.648000] br-lan: port 1(eth0) entered forwarding state
[   52.724000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   52.736000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   52.740000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  118.564000] JFFS2 notice: (1118) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler]
Tienes wifi sin problemas, verdad?

Si puedes ejecuta el siguiente comando y pon el resultado:
Código: [Seleccionar]
ls /lib/firmware
Saludos y muchas gracias por la prueba!

Sip, tengo wifi sin problemas, ahoramismo lo estoy usando en modo cliente y va perfect.

Código: [Seleccionar]
root@OpenWrt:~# ls /lib/firmware
RT3062.eeprom  rt2860.bin     rt3290.bin


Si quieres mas pruebas dimelo, estaré por aquí.
« Última modificación: 08-11-2012, 14:37 (Jueves) por geminis_demon »
En línea

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #879 en: 08-11-2012, 14:55 (Jueves) »
Cita de: geminis_demon en 08-11-2012, 14:36 (Jueves)
Cita de: Noltari en 08-11-2012, 14:22 (Jueves)
Cita de: geminis_demon en 08-11-2012, 13:41 (Jueves)
Aquí un ralinkero, voy a bajar la compilación y en unos minutos posteo los resultados.

Pues aquí está el dmsg:

[spoiler=dmesg]
Código: [Seleccionar]
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #3 Tue Nov 6 20:12:59 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802a5b10, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61720k/65536k available (2238k kernel code, 3816k reserved, 409k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] PCI: CLS 0 bytes, default 16
[    0.196000] audit: initializing netlink socket (disabled)
[    0.204000] type=2000 audit(0.204:1): initialized
[    0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.268000] physmap platform flash device: 02000000 at 1e000000
[    0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.288000]   Amd/Fujitsu Extended Query version 1.3.
[    0.296000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.328000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.348000] bcm63xxpart: Spare partition is offset 3a0004 and length b3fffc
[    0.356000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.364000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.368000] 0x000000000000-0x000000020000 : "CFE"
[    0.380000] 0x000000020100-0x000000120000 : "kernel"
[    0.384000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.400000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.408000] mtd: partition "rootfs" set to be root filesystem
[    0.416000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=B40000
[    0.424000] 0x0000003a0000-0x000000ee0000 : "rootfs_data"
[    0.432000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.444000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.452000] 0x000000020000-0x000000ee0000 : "linux"
[    0.472000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.480000] Registered led device: HW556:red:message
[    0.480000] Registered led device: HW556:red:hspa
[    0.480000] Registered led device: HW556:red:dsl
[    0.484000] Registered led device: HW556:red:power
[    0.484000] Registered led device: HW556:red:all
[    0.484000] TCP cubic registered
[    0.488000] NET: Registered protocol family 17
[    0.492000] 8021q: 802.1Q VLAN Support v1.8
[    0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.516000] Freeing unused kernel memory: 208k freed
[    3.284000] eth0: link forced UP - 100/full - flow control off/off
[    3.544000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.612000] There is already a switch registered on the device 'eth0'
[    6.076000] Button Hotplug driver version 0.4.1
[    6.112000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   13.416000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.424000] Backport based on wireless-testing.git master-2012-09-07
[   13.428000] compat.git: wireless-testing.git
[   13.492000] cfg80211: Calling CRDA to update world regulatory domain
[   13.500000] cfg80211: World regulatory domain updated:
[   13.504000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.516000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.524000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.532000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.540000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.548000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.000000] NET: Registered protocol family 10
[   14.492000] SCSI subsystem initialized
[   14.588000] There is already a switch registered on the device 'eth0'
[   14.856000] usbcore: registered new interface driver usbfs
[   14.860000] usbcore: registered new interface driver hub
[   14.868000] usbcore: registered new device driver usb
[   16.096000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.100000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.416000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.420000] Registered led device: rt2800pci-phy0::radio
[   16.420000] Registered led device: rt2800pci-phy0::assoc
[   16.420000] Registered led device: rt2800pci-phy0::quality
[   17.784000] PPP generic driver version 2.4.2
[   18.188000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] NET: Registered protocol family 24
[   18.892000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.004000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.008000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.044000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.060000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.068000] hub 1-0:1.0: USB hub found
[   19.072000] hub 1-0:1.0: 2 ports detected
[   19.128000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
[   20.268000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   20.700000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.812000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.816000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.824000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.892000] hub 2-0:1.0: USB hub found
[   20.896000] hub 2-0:1.0: 1 port detected
[   21.104000] Initializing USB Mass Storage driver...
[   21.108000] usbcore: registered new interface driver usb-storage
[   21.116000] USB Mass Storage support registered.
[   21.300000] usbcore: registered new interface driver ums-alauda
[   21.340000] usbcore: registered new interface driver ums-cypress
[   21.380000] usbcore: registered new interface driver ums-datafab
[   21.420000] usbcore: registered new interface driver ums-freecom
[   21.456000] usbcore: registered new interface driver ums-isd200
[   21.496000] usbcore: registered new interface driver ums-jumpshot
[   21.532000] usbcore: registered new interface driver ums-karma
[   21.572000] usbcore: registered new interface driver ums-sddr09
[   21.612000] usbcore: registered new interface driver ums-sddr55
[   21.652000] usbcore: registered new interface driver ums-usbat
[   21.732000] fuse init (API version 7.18)
[   27.616000] eth0: link forced UP - 100/full - flow control off/off
[   27.632000] device eth0 entered promiscuous mode
[   27.640000] br-lan: port 1(eth0) entered forwarding state
[   27.644000] br-lan: port 1(eth0) entered forwarding state
[   29.648000] br-lan: port 1(eth0) entered forwarding state
[   52.724000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   52.736000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   52.740000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  118.564000] JFFS2 notice: (1118) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler]
Tienes wifi sin problemas, verdad?

Si puedes ejecuta el siguiente comando y pon el resultado:
Código: [Seleccionar]
ls /lib/firmware
Saludos y muchas gracias por la prueba!

Sip, tengo wifi sin problemas, ahoramismo lo estoy usando en modo cliente y va perfect.

Código: [Seleccionar]
root@OpenWrt:~# ls /lib/firmware
RT3062.eeprom  rt2860.bin     rt3290.bin


Si quieres mas pruebas dimelo, estaré por aquí.
De momento no, muchas gracias ^^.
En línea
Páginas: 1 ... 37 38 39 40 41 42 43 [44] 45 46 47 48 49 50 51 ... 156   Ir Arriba
« anterior próximo »
 

Si quieres tener la mejor experiencia posible de navegación y uso de la web activa y acepta nuestras políticas de privacidad y cookies. En caso contrario te recomendamos abandonar la web y buscar la información en otro sitio. Si quieres registrarte en el foro deberás aceptar las políticas de privacidad y las condiciones de uso. Learn more