?>/script>'; } ?> [Desarrollo] OpenWrt en Huawei HG556a Widgets Magazine

Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a  (Leído 2231141 veces)

0 Usuarios y 1 Visitante están viendo este tema.

Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #920 en: 26-11-2012, 22:35 (Lunes) »
Ralink funcionando ok como cliente enrutado.  >:( >:( >:( >:( >:( >:(

PD: Molestias, ningunas. Todo lo contrario, muy agradecido por todas las molestias que os tomási para que estas cosas avancen.


Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #921 en: 27-11-2012, 00:07 (Martes) »
Resumiendo, 3 atheros y un ralink funcionando con el último firmware. Mañana actualizaré otro Ralink que tengo en el curro.


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #922 en: 27-11-2012, 00:38 (Martes) »
Resumiendo, 3 atheros y un ralink funcionando con el último firmware. Mañana actualizaré otro Ralink que tengo en el curro.
Te recuerdo que los firmwares van un poco "pelados", porque para andar probando cosas es más rápido compilar menos paquetes.

Muchas gracias por las pruebas ;).


Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4608
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #923 en: 27-11-2012, 09:07 (Martes) »
Actualizados los parches para el SVN del primer post.
Llevo un par de semanas MUY LIADO con la universidad, por lo que no tengo mucho tiempo...
Así que si alguien quiere compilar un firmware con los parches y subirlo se lo agradecería.

A parte de eso, jogo ha integrado mis parches para el led pin y para el wifi de los ralink.
https://dev.openwrt.org/changeset/34321
https://dev.openwrt.org/changeset/34322

Por tanto, sólo quedan los parches de la placa y de los fixup para detectar los cal_data de cada modelo.
Antes de mandar estos parches, tengo que hablar con jogo para que actualice su parche del mtd, de modo que los cal_data no se borren si no están situados al final de la flash junto al nvram, como es el caso de los HW556. Aun así, como ya he dicho estoy bastante ocupado y no sé si esto será dentro de poco o más adelante.

Saludos!

Osea que estamos muy cerca del soporte oficial de OpenWrt para este router no ?  >:( >:(

Siento no poder probar ahora mismo nada en los hg556a. Los dos equipos que tengo están 'prestados' ... :P
Pero bueno, para eso ya tenemos a Elnef y su colección: 4 routers !!!!  ;D


jbconpepsi

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #924 en: 27-11-2012, 09:16 (Martes) »
Otro con Atheros funcionando perfectamente el wifi.  >:( Ahora a ver si alguien se curra un firmware con más opciones.

Gracias.

Saludos.


Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #925 en: 27-11-2012, 12:02 (Martes) »
Mi segundo Ralink ya está actualizado y funcionando como punto de acceso.  ^-^ ^-^

PD: Respecto al tema de que este firmware esté pelado, debo decir que yo uso los routers como routers. No les meto torrent, ni samba, ni ftp, ni radio wifi, ni nada por el estilo. Simplemente los uso como AP, Clientes y repetidores.

Aunque la verdad es que si alguien se curra un firmware con todos los extras lo mismo le meto mano aunque sólo sea por el cacharreo.


Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #926 en: 27-11-2012, 12:08 (Martes) »
Como curiosidad os comentaré que he observado que los dos router Ralink tienen la misma MAC Address  en la parte del wifi. Así que no pueden convivir en la misma red porque generan fallos. Cosa que en los Atheros no pasa.

Y es curioso porque yo pensaba que la MAC debía ser exclusiva de cada dispositivo. Y no se si es debido a que el OpenWRT le asigne una MAC por defecto.

Si alguien tiene Ralink le agradecería si puede comprobar que la MAC de su wifi también es:

00:0C:43:30:62:01   


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #927 en: 27-11-2012, 12:14 (Martes) »
Muchas gracias a todos por las pruebas.

Como curiosidad os comentaré que he observado que los dos router Ralink tienen la misma MAC Address  en la parte del wifi. Así que no pueden convivir en la misma red porque generan fallos. Cosa que en los Atheros no pasa.

Y es curioso porque yo pensaba que la MAC debía ser exclusiva de cada dispositivo. Y no se si es debido a que el OpenWRT le asigne una MAC por defecto.

Si alguien tiene Ralink le agradecería si puede comprobar que la MAC de su wifi también es:

00:0C:43:30:62:01   
Estoy al tanto de este problema. Lo solucionaré una vez haya soporte oficial para el router.

El problema es que los cal_data de la flash de los ralink tienen todos la misma dirección MAC.
En el caso de los atheros, la dirección MAC de los cal_data es inválida, por lo que el driver coge la dirección MAC del platform data que le pasas al registrar los datos del WiFi. Sin embargo, en los Ralink, la dirección MAC es válida, por lo que no coge la dirección MAC del platform data.
Por tanto, tengo que mirar el driver a fondo y cambiarlo para que se pueda forzar de alguna forma e ignorar los cal_data de la flash y coger los del platform.

Osea que estamos muy cerca del soporte oficial de OpenWrt para este router no ?  >:( >:(

Siento no poder probar ahora mismo nada en los hg556a. Los dos equipos que tengo están 'prestados' ... :P
Pero bueno, para eso ya tenemos a Elnef y su colección: 4 routers !!!!  ;D
Efectivamente, cuando jogo acepte los parches que hay en espera, habrá soporte oficial de openwrt para este router :).

Saludos!


Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #928 en: 27-11-2012, 12:24 (Martes) »
Entonces ya me queda claro que es cosa del openwrt lo de las MAC idénticas.

PD: ¿Creéis que en un futuro este router podrá tener alguna vez soporte para ADSL?

« Última modificación: 27-11-2012, 12:25 (Martes) por Elnef »

Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #929 en: 27-11-2012, 20:44 (Martes) »
Entonces ya me queda claro que es cosa del openwrt lo de las MAC idénticas.

PD: ¿Creéis que en un futuro este router podrá tener alguna vez soporte para ADSL?

Cuando tengas un rato prueba este firmware en un HG556a ralink.
He intentado modificar el driver rt2x00 para que sobreescriba la mac del WiFi con la del platform data.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r34398.bin

Necesito que me envíes un bootlog y la configuración wireless nada más flashear el router.
Código: [Seleccionar]
dmesg > /www/dmesg.txt
cp /etc/config/wireless /www/wifi.txt
http://192.168.1.1/dmesg.txt
http://192.168.1.1/wifi.txt

Con respecto a lo del ADSL es muy improbable porque Broadcom no libera el código fuente del driver ADSL y no es algo "trivial" de conseguir.
Aun así, hay gente que lo está mirando, pero claro, llevan así desde que hubo soporte de openwrt para bcm63xx...

Saludos!

« Última modificación: 27-11-2012, 21:36 (Martes) por Noltari »

Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #930 en: 27-11-2012, 21:36 (Martes) »
He actualizado el firmware, porque había cambiado la sección de la carga de la EEPROM por PCI, en lugar de por firmware.

Saludos.


Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #931 en: 28-11-2012, 07:24 (Miércoles) »
Probada la 34398 en mis dos Ralink y ambos funcionando OK. Ahora la MAC de cada equipo es diferente y viendo que coinciden los 3 primeros bytes, que son los del fabricante, parece que todo está correcto.

Dmesg

Código: [Seleccionar]
[    0.000000] Linux version 3.6.7 (noltari@skynet) (gcc version 4.6.4 20121106 (prerelease) (Linaro GCC 4.6-2012.11) ) #2 Tue Nov 27 21:33:53 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] No bcm_tag found!
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556_A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802b81e0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Memory: 61644k/65536k available (2293k kernel code, 3892k reserved, 429k data, 212k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.112000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
[    0.112000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[    0.112000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.124000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.124000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.124000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.128000] Switching to clocksource MIPS
[    0.140000] NET: Registered protocol family 2
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.152000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.160000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.168000] TCP: reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.176000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.184000] NET: Registered protocol family 1
[    0.188000] PCI: CLS 0 bytes, default 16
[    0.192000] audit: initializing netlink socket (disabled)
[    0.200000] type=2000 audit(0.200:1): initialized
[    0.204000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.212000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.264000] physmap platform flash device: 02000000 at 1e000000
[    0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.280000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.280000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.284000]   Amd/Fujitsu Extended Query version 1.3.
[    0.292000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.316000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.324000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.332000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.344000] bcm63xxpart: Spare partition is offset 2e0004 and length bffffc
[    0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.360000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.364000] 0x000000000000-0x000000020000 : "CFE"
[    0.376000] 0x000000020100-0x000000120000 : "kernel"
[    0.380000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.404000] mtd: partition "rootfs" set to be root filesystem
[    0.412000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=C00000
[    0.420000] 0x0000002e0000-0x000000ee0000 : "rootfs_data"
[    0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.440000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.448000] 0x000000020000-0x000000ee0000 : "linux"
[    0.468000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.476000] Registered led device: HW556:red:message
[    0.476000] Registered led device: HW556:red:hspa
[    0.476000] Registered led device: HW556:red:dsl
[    0.480000] Registered led device: HW556:red:power
[    0.480000] Registered led device: HW556:red:all
[    0.480000] TCP: cubic registered
[    0.484000] NET: Registered protocol family 17
[    0.488000] 8021q: 802.1Q VLAN Support v1.8
[    0.504000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.512000] Freeing unused kernel memory: 212k freed
[    3.324000] eth0: link forced UP - 100/full - flow control off/off
[    3.392000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.456000] There is already a switch registered on the device 'eth0'
[    5.876000] Button Hotplug driver version 0.4.1
[    5.908000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    9.944000] jffs2: notice: (359) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found.
[   13.256000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.264000] Backport based on wireless-testing.git master-2012-09-07
[   13.272000] compat.git: wireless-testing.git
[   13.332000] cfg80211: Calling CRDA to update world regulatory domain
[   13.340000] cfg80211: World regulatory domain updated:
[   13.344000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.352000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.360000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.368000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.376000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.384000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.784000] There is already a switch registered on the device 'eth0'
[   14.852000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   14.860000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   15.072000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   15.072000] Registered led device: rt2800pci-phy0::radio
[   15.076000] Registered led device: rt2800pci-phy0::assoc
[   15.076000] Registered led device: rt2800pci-phy0::quality
[   15.312000] PPP generic driver version 2.4.2
[   15.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.796000] NET: Registered protocol family 24
[   15.840000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[   21.100000] eth0: link forced UP - 100/full - flow control off/off
[   21.128000] device eth0 entered promiscuous mode
[   21.140000] br-lan: port 1(eth0) entered forwarding state
[   21.144000] br-lan: port 1(eth0) entered forwarding state
[   23.148000] br-lan: port 1(eth0) entered forwarding state
[   25.660000] device wlan0 entered promiscuous mode
[   26.848000] br-lan: port 2(wlan0) entered forwarding state
[   26.852000] br-lan: port 2(wlan0) entered forwarding state
[   28.856000] br-lan: port 2(wlan0) entered forwarding state

Wireless
Código: [Seleccionar]
config wifi-device 'radio0'
option type 'mac80211'
option channel '11'
option hwmode '11ng'
option path 'pci0000:00/0000:00:01.0'
option htmode 'HT20'
list ht_capab 'GF'
list ht_capab 'SHORT-GI-20'
list ht_capab 'SHORT-GI-40'
list ht_capab 'TX-STBC'
list ht_capab 'RX-STBC12'
option txpower '20'
option country '00'

config wifi-iface
option device 'radio0'
option network 'lan'
option mode 'ap'
option ssid 'OpenWrt'
option encryption 'psk+ccmp'
option key 'PASSWORD'


Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #932 en: 28-11-2012, 09:21 (Miércoles) »
He visto otra curiosidad del firmware. Cuando usamos "OPKG" ataca a la dirección:

http://downloads.openwrt.org/snapshots/trunk/brcm63xx/packages

Y creo que ahora es:

http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages

De todas formas se actualiza y descarga paquetes, pero no se si habría que corregirlo.


Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4608
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #933 en: 28-11-2012, 09:38 (Miércoles) »
He visto otra curiosidad del firmware. Cuando usamos "OPKG" ataca a la dirección:

http://downloads.openwrt.org/snapshots/trunk/brcm63xx/packages

Y creo que ahora es:

http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages

De todas formas se actualiza y descarga paquetes, pero no se si habría que corregirlo.

La dirección correcta es la del trunk.
Ten en cuenta que ahora ya no estamos trabajando sobre Attitude Adjustment, sino sobre Barrier Breaker  >:D


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #934 en: 28-11-2012, 12:30 (Miércoles) »
Probada la 34398 en mis dos Ralink y ambos funcionando OK. Ahora la MAC de cada equipo es diferente y viendo que coinciden los 3 primeros bytes, que son los del fabricante, parece que todo está correcto.
Muchas gracias por las pruebas ^^.

¿Podrías probar si con este otro firmware también funciona bien? Es que he cambiado los parches para que tengan más probabilidades de ser aceptados en Openwrt.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r34398_legpatch.bin

P.D: No hace falta que envíes el dmesg y el config/wireless, con que me digas que la MAC está bien me vale :P.

Saludos!

« Última modificación: 28-11-2012, 14:22 (Miércoles) por Noltari »

Elnef

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #935 en: 28-11-2012, 14:08 (Miércoles) »
Probada en los dos Ralink y funcionando con la MAC correcta. De hecho he configurado uno como AP y el otro como cliente del mismo y todo OK. Antes con las mismas MAC esta cofiguracicón era imposible.


fRUTTiFrESH

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #936 en: 28-11-2012, 18:53 (Miércoles) »
Thank You Noltari for the fresh Build  >:(

I have problems installing oscam_1.20-svn-7940_brcm63xx.ipk -> pcscd_1.8.6-1_brcm63xx.ipk and libpcsclite_1.8.6-1_brcm63xx.ipk install without a problem, but when I try to install oscam - I´ve get ->

Código: [Seleccionar]
root@OpenWrt:/tmp# opkg update
Downloading http://downloads.openwrt.org/snapshots/trunk/brcm63xx/packages/Packa                                                                                       ges.gz.
Inflating http://downloads.openwrt.org/snapshots/trunk/brcm63xx/packages/Packages.gz.
Updated list of available packages in /var/opkg-lists/barrier_breaker.
root@OpenWrt:/tmp# opkg install pcscd_1.8.6-1_brcm63xx.ipk
Installing pcscd (1.8.6-1) to root...
Configuring pcscd.
root@OpenWrt:/tmp# opkg install libpcsclite_1.8.6-1_brcm63xx.ipk
Installing libpcsclite (1.8.6-1) to root...
Configuring libpcsclite.
root@OpenWrt:/tmp# opkg install oscam_1.20-svn-7940_brcm63xx.ipk
Installing oscam (1.20-svn-7940) to root...
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for oscam:
 *      pcsc-lite *
 * opkg_install_cmd: Cannot install package oscam.

Any idea?

Thanks in advance

dmesg:

[spoiler][    0.000000] Linux version 3.6.7 (noltari@skynet) (gcc version 4.6.4 20121106 (prerelease) (Linaro GCC 4.6-2012.11) ) #1 Wed Nov 28 12:22:16 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] No bcm_tag found!
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556_A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802b81e0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Memory: 61644k/65536k available (2293k kernel code, 3892k reserved, 429k data, 212k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.112000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
[    0.112000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[    0.112000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.124000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.124000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.124000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.128000] Switching to clocksource MIPS
[    0.140000] NET: Registered protocol family 2
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.152000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.160000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.168000] TCP: reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.176000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.184000] NET: Registered protocol family 1
[    0.188000] PCI: CLS 0 bytes, default 16
[    0.192000] audit: initializing netlink socket (disabled)
[    0.200000] type=2000 audit(0.200:1): initialized
[    0.204000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.212000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.264000] physmap platform flash device: 02000000 at 1e000000
[    0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.280000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.280000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.284000]   Amd/Fujitsu Extended Query version 1.3.
[    0.292000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.316000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.324000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.332000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.344000] bcm63xxpart: Spare partition is offset 2e0004 and length bffffc
[    0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.360000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.364000] 0x000000000000-0x000000020000 : "CFE"
[    0.376000] 0x000000020100-0x000000120000 : "kernel"
[    0.380000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.404000] mtd: partition "rootfs" set to be root filesystem
[    0.412000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=C00000
[    0.420000] 0x0000002e0000-0x000000ee0000 : "rootfs_data"
[    0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.440000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.448000] 0x000000020000-0x000000ee0000 : "linux"
[    0.468000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.476000] Registered led device: HW556:red:message
[    0.476000] Registered led device: HW556:red:hspa
[    0.476000] Registered led device: HW556:red:dsl
[    0.480000] Registered led device: HW556:red:power
[    0.480000] Registered led device: HW556:red:all
[    0.480000] TCP: cubic registered
[    0.484000] NET: Registered protocol family 17
[    0.488000] 8021q: 802.1Q VLAN Support v1.8
[    0.504000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.512000] Freeing unused kernel memory: 212k freed
[    3.320000] eth0: link forced UP - 100/full - flow control off/off
[    3.392000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.456000] There is already a switch registered on the device 'eth0'
[    5.876000] Button Hotplug driver version 0.4.1
[    5.908000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    9.964000] jffs2: notice: (359) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found.
[   13.352000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.360000] Backport based on wireless-testing.git master-2012-09-07
[   13.368000] compat.git: wireless-testing.git
[   13.428000] cfg80211: Calling CRDA to update world regulatory domain
[   13.436000] cfg80211: World regulatory domain updated:
[   13.440000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.448000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.456000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.464000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.472000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.480000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.920000] There is already a switch registered on the device 'eth0'
[   14.124000] usbcore: registered new interface driver usbfs
[   14.128000] usbcore: registered new interface driver hub
[   14.136000] usbcore: registered new device driver usb
[   15.212000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.220000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   15.432000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   15.432000] Registered led device: rt2800pci-phy0::radio
[   15.432000] Registered led device: rt2800pci-phy0::assoc
[   15.432000] Registered led device: rt2800pci-phy0::quality
[   15.676000] PPP generic driver version 2.4.2
[   15.928000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.172000] NET: Registered protocol family 24
[   16.216000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[   16.688000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   16.796000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   16.800000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
[   16.808000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   16.876000] hub 1-0:1.0: USB hub found
[   16.880000] hub 1-0:1.0: 1 port detected
[   16.944000] uhci_hcd: USB Universal Host Controller Interface driver
[   17.016000] usbcore: registered new interface driver usbserial
[   17.020000] usbcore: registered new interface driver usbserial_generic
[   17.028000] USB Serial support registered for generic
[   17.032000] usbserial: USB Serial Driver core
[   17.140000] usbcore: registered new interface driver ftdi_sio
[   17.148000] USB Serial support registered for FTDI USB Serial Device
[   17.152000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[   17.272000] usb 1-1: new full-speed USB device number 2 using bcm63xx_ohci
[   17.448000] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
[   17.456000] usb 1-1: Detected FT232RL
[   17.460000] usb 1-1: Number of endpoints 2
[   17.464000] usb 1-1: Endpoint 1 MaxPacketSize 16384
[   17.468000] usb 1-1: Endpoint 2 MaxPacketSize 16384
[   17.472000] usb 1-1: Setting MaxPacketSize 64
[   17.484000] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
[   22.272000] eth0: link forced UP - 100/full - flow control off/off
[   22.304000] device eth0 entered promiscuous mode
[   22.320000] br-lan: port 1(eth0) entered forwarding state
[   22.324000] br-lan: port 1(eth0) entered forwarding state
[   24.328000] br-lan: port 1(eth0) entered forwarding state
[   27.592000] device wlan0 entered promiscuous mode
[   29.100000] br-lan: port 2(wlan0) entered forwarding state
[   29.104000] br-lan: port 2(wlan0) entered forwarding state
[   31.108000] br-lan: port 2(wlan0) entered forwarding state[/spoiler]


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #937 en: 28-11-2012, 20:31 (Miércoles) »
Thank You Noltari for the fresh Build  >:(

I have problems installing oscam_1.20-svn-7940_brcm63xx.ipk -> pcscd_1.8.6-1_brcm63xx.ipk and libpcsclite_1.8.6-1_brcm63xx.ipk install without a problem, but when I try to install oscam - I´ve get ->

Código: [Seleccionar]
root@OpenWrt:/tmp# opkg update
Downloading http://downloads.openwrt.org/snapshots/trunk/brcm63xx/packages/Packa                                                                                       ges.gz.
Inflating http://downloads.openwrt.org/snapshots/trunk/brcm63xx/packages/Packages.gz.
Updated list of available packages in /var/opkg-lists/barrier_breaker.
root@OpenWrt:/tmp# opkg install pcscd_1.8.6-1_brcm63xx.ipk
Installing pcscd (1.8.6-1) to root...
Configuring pcscd.
root@OpenWrt:/tmp# opkg install libpcsclite_1.8.6-1_brcm63xx.ipk
Installing libpcsclite (1.8.6-1) to root...
Configuring libpcsclite.
root@OpenWrt:/tmp# opkg install oscam_1.20-svn-7940_brcm63xx.ipk
Installing oscam (1.20-svn-7940) to root...
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for oscam:
 *      pcsc-lite *
 * opkg_install_cmd: Cannot install package oscam.

Any idea?

Thanks in advance

dmesg:

[spoiler][    0.000000] Linux version 3.6.7 (noltari@skynet) (gcc version 4.6.4 20121106 (prerelease) (Linaro GCC 4.6-2012.11) ) #1 Wed Nov 28 12:22:16 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] No bcm_tag found!
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556_A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802b81e0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Memory: 61644k/65536k available (2293k kernel code, 3892k reserved, 429k data, 212k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.112000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
[    0.112000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[    0.112000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.124000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.124000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.124000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.128000] Switching to clocksource MIPS
[    0.140000] NET: Registered protocol family 2
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.152000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.160000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.168000] TCP: reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.176000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.184000] NET: Registered protocol family 1
[    0.188000] PCI: CLS 0 bytes, default 16
[    0.192000] audit: initializing netlink socket (disabled)
[    0.200000] type=2000 audit(0.200:1): initialized
[    0.204000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.212000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.224000] msgmni has been set to 120
[    0.228000] io scheduler noop registered
[    0.232000] io scheduler deadline registered (default)
[    0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.248000] console [ttyS0] enabled, bootconsole disabled
[    0.264000] physmap platform flash device: 02000000 at 1e000000
[    0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.280000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.280000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.284000]   Amd/Fujitsu Extended Query version 1.3.
[    0.292000] number of CFI chips: 1
[    0.296000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.316000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length dc0000
[    0.324000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.332000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.340000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.344000] bcm63xxpart: Spare partition is offset 2e0004 and length bffffc
[    0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.360000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.364000] 0x000000000000-0x000000020000 : "CFE"
[    0.376000] 0x000000020100-0x000000120000 : "kernel"
[    0.380000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] 0x000000120000-0x000000ee0000 : "rootfs"
[    0.404000] mtd: partition "rootfs" set to be root filesystem
[    0.412000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=C00000
[    0.420000] 0x0000002e0000-0x000000ee0000 : "rootfs_data"
[    0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.440000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.448000] 0x000000020000-0x000000ee0000 : "linux"
[    0.468000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.476000] Registered led device: HW556:red:message
[    0.476000] Registered led device: HW556:red:hspa
[    0.476000] Registered led device: HW556:red:dsl
[    0.480000] Registered led device: HW556:red:power
[    0.480000] Registered led device: HW556:red:all
[    0.480000] TCP: cubic registered
[    0.484000] NET: Registered protocol family 17
[    0.488000] 8021q: 802.1Q VLAN Support v1.8
[    0.504000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.512000] Freeing unused kernel memory: 212k freed
[    3.320000] eth0: link forced UP - 100/full - flow control off/off
[    3.392000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.456000] There is already a switch registered on the device 'eth0'
[    5.876000] Button Hotplug driver version 0.4.1
[    5.908000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    9.964000] jffs2: notice: (359) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found.
[   13.352000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.360000] Backport based on wireless-testing.git master-2012-09-07
[   13.368000] compat.git: wireless-testing.git
[   13.428000] cfg80211: Calling CRDA to update world regulatory domain
[   13.436000] cfg80211: World regulatory domain updated:
[   13.440000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.448000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.456000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.464000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.472000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.480000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.920000] There is already a switch registered on the device 'eth0'
[   14.124000] usbcore: registered new interface driver usbfs
[   14.128000] usbcore: registered new interface driver hub
[   14.136000] usbcore: registered new device driver usb
[   15.212000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.220000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   15.432000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   15.432000] Registered led device: rt2800pci-phy0::radio
[   15.432000] Registered led device: rt2800pci-phy0::assoc
[   15.432000] Registered led device: rt2800pci-phy0::quality
[   15.676000] PPP generic driver version 2.4.2
[   15.928000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.172000] NET: Registered protocol family 24
[   16.216000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[   16.688000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   16.796000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   16.800000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
[   16.808000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   16.876000] hub 1-0:1.0: USB hub found
[   16.880000] hub 1-0:1.0: 1 port detected
[   16.944000] uhci_hcd: USB Universal Host Controller Interface driver
[   17.016000] usbcore: registered new interface driver usbserial
[   17.020000] usbcore: registered new interface driver usbserial_generic
[   17.028000] USB Serial support registered for generic
[   17.032000] usbserial: USB Serial Driver core
[   17.140000] usbcore: registered new interface driver ftdi_sio
[   17.148000] USB Serial support registered for FTDI USB Serial Device
[   17.152000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[   17.272000] usb 1-1: new full-speed USB device number 2 using bcm63xx_ohci
[   17.448000] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
[   17.456000] usb 1-1: Detected FT232RL
[   17.460000] usb 1-1: Number of endpoints 2
[   17.464000] usb 1-1: Endpoint 1 MaxPacketSize 16384
[   17.468000] usb 1-1: Endpoint 2 MaxPacketSize 16384
[   17.472000] usb 1-1: Setting MaxPacketSize 64
[   17.484000] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
[   22.272000] eth0: link forced UP - 100/full - flow control off/off
[   22.304000] device eth0 entered promiscuous mode
[   22.320000] br-lan: port 1(eth0) entered forwarding state
[   22.324000] br-lan: port 1(eth0) entered forwarding state
[   24.328000] br-lan: port 1(eth0) entered forwarding state
[   27.592000] device wlan0 entered promiscuous mode
[   29.100000] br-lan: port 2(wlan0) entered forwarding state
[   29.104000] br-lan: port 2(wlan0) entered forwarding state
[   31.108000] br-lan: port 2(wlan0) entered forwarding state[/spoiler]
Looks like some dependencies are missing:
Código: [Seleccionar]
Installing oscam (1.20-svn-7940) to root...
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for oscam:
 *      pcsc-lite *
 * opkg_install_cmd: Cannot install package oscam.

If I were you I would compile my own firmware including all the packages I want.
It's better and always solves all opkg installing errors (custom kernels, etc.).

However, I haven't published the final patches for this router, so I suggest you to wait until all the patches are committed since it souldn't take long.

Greetings.



fRUTTiFrESH

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #939 en: 28-11-2012, 20:53 (Miércoles) »
Sorry Noltari,

I´am not a Progger ;)

No Problem for me to build my own firmware (thanks jar229 for the good guide!)
I have to play more around with OpenWRT and the HG556a... but I need help!

Thanks for the good community and the support!

Really appreciate it!

Regards from Moraira
Frutti