hola-
arv4518 r01a
NO arranca pagina inicio ....web
esto me sale con hyperterminal
ROM VER: 1.0.3
CFG 01
Readü
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X
U-Boot 2010.03 (Oct 19 2012 - 15:13:04)
Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.5, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2013-04-03 8:56:49 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1017152 Bytes = 993.3 kB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc ve
rsion 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 11:36
:28 UTC 2013
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,j
ffs2 machtype=ARV4518PW
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00029728
[ 0.000000] Readback ErrCtl register=00029728
[ 0.000000] Memory: 61704k/65536k available (2413k kernel code, 3832k reserved,
04k data, 176k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.056000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio
[ 0.060000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio
[ 0.064000] MIPS: machine is ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.068000] gpiochip_add: registered GPIOs 100 to 115 on device: ltq_ebu
[ 0.108000] bio: create slab <bio-0> at 0
[ 0.116000] PCI host bridge to bus 0000:00
[ 0.120000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.124000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.128000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.132000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
[ 0.136000] Switching to clocksource MIPS
[ 0.144000] NET: Registered protocol family 2
[ 0.152000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.156000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.164000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.172000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.176000] TCP reno registered
[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.192000] NET: Registered protocol family 1
[ 0.200000] gptu: totally 6 16-bit timers/counters
[ 0.204000] gptu: misc_register on minor 63
[ 0.208000] gptu: succeeded to request irq 126
[ 0.212000] gptu: succeeded to request irq 127
[ 0.216000] gptu: succeeded to request irq 128
[ 0.220000] gptu: succeeded to request irq 129
[ 0.228000] gptu: succeeded to request irq 130
[ 0.232000] gptu: succeeded to request irq 131
[ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.244000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.256000] msgmni has been set to 120
[ 0.260000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.268000] io scheduler noop registered
[ 0.272000] io scheduler deadline registered (default)
[ 0.276000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[ 0.284000] console [ttyLTQ1] enabled, bootconsole disabled
[ 0.284000] console [ttyLTQ1] enabled, bootconsole disabled
[ 0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x0022a8
[ 0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.312000] Amd/Fujitsu Extended Query version 1.1.
[ 0.316000] number of CFI chips: 1
[ 0.320000] Creating 4 MTD partitions on "ltq_nor":
[ 0.324000] 0x000000000000-0x000000010000 : "uboot"
[ 0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.340000] 0x000000020000-0x0000003f0000 : "linux"
[ 0.348000] found squashfs behind kernel
[ 0.348000] Creating 2 MTD partitions on "ltq_nor":
[ 0.352000] 0x000000020000-0x000000118580 : "kernel"
[ 0.360000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.372000] 0x000000118580-0x0000003f0000 : "rootfs"
[ 0.376000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.392000] mtd: partition "rootfs" set to be root filesystem
[ 0.396000] mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=120000
[ 0.404000] 0x0000002d0000-0x0000003f0000 : "rootfs_data"
[ 0.412000] 0x0000003f0000-0x000000400000 : "board_config"
[ 0.424000] etop: invalid MAC, using random
[ 0.440000] ltq_mii: probed
[ 0.472000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
[ 0.480000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=ltq_etop-fffffff:00, irq=-1)
[ 0.500000] TCP cubic registered
[ 0.500000] NET: Registered protocol family 17
[ 0.508000] Bridge firewalling registered
[ 0.508000] 8021q: 802.1Q VLAN Support [ 0.532000] VFS: Mounted root (squa
shfs filesystem) readonly on device 31:4.
[ 0.536000] Freeing unused kernel memory: 176k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
f- regular preinit -
[ 7.268000] JFFS2 notice: (350) jffs2_build_xattr_subsystem: complete buildin
g xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 4 of xref (0 dead, 0
orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 8.528000] Compat-drivers backp
ort release: compat-drivers-2012-09-04-2-gddac993
[ 8.536000] Backport based on wireless-testing.git master-2012-09-07
[ 8.540000] compat.git: wireless-testing.git
[ 8.580000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.584000] cfg80211: World regulatory domain updated:
[ 8.588000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.596000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.604000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.612000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.620000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.624000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.312000] usbcore: registered new interface driver usbfs
[ 9.316000] usbcore: registered new interface driver hub
[ 9.324000] usbcore: registered new device driver usb
[ 10.144000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 10.148000] ath5k 0000:00:0e.0: registered as 'phy0'
[ 11.312000] ath5k: phy0: unable to init EEPROM
[ 11.316000] ath5k: probe of 0000:00:0e.0 failed with error -5
[ 11.344000] NET: Registered protocol family 8
[ 11.344000] NET: Registered protocol family 20
[ 11.520000] Button Hotplug driver version 0.4.1
[ 11.560000] PPP generic driver version 2.4.2
[ 12.256000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.712000] NET: Registered protocol family 24
[ 12.740000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
[ 13.388000] IFX MEI Version 5.00.00
[ 13.420000]
[ 13.420000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[ 13.456000] ATM (A1) firmware version 1.0.19
[ 13.456000] ifxmips_atm: ATM init succeed
[ 13.488000] dwc_otg: version 2.60a 22-NOV-2006
[ 14.096000] DWC_otg: Using DMA mode
[ 14.096000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 14.100000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 14.108000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
[ 14.116000] DWC_otg: Init: Port Power? op_state=1
[ 14.120000] DWC_otg: Init: Power Port (0)
[ 14.124000] hub 1-0:1.0: USB hub found
[ 14.128000] hub 1-0:1.0: 1 port detected
[ 14.152000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 14.232000] DISCONNECTED PORT
[ 20.836000] device eth0 entered promiscuous mode
[ 20.844000] br-lan: port 1(eth0) entered forwarding state
[ 20.848000] br-lan: port 1(eth0) entered forwarding state
[ 22.852000] br-lan: port 1(eth0) entered forwarding state
BusyBox v1.19.4 (2013-03-12 15:13:26 UTC) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
ATTITUDE ADJUSTMENT (12.09, r36088)
-----------------------------------------------------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#