Autor Tema: [Desarrollo] OpenWrt en ASTORIA ARV7519RW22 (Leído 513635 veces)

doblecero · « **Respuesta #520 en:** 11-10-2014, 23:40 (Sábado) »

Como módem adsl ya funcionaba bien antes.

Solo hay que soldar 3 pins! Es fácil fácil!

Transmisión, samba y mucho mas! Este equipo puede con ello. Aunque creo que la velocidad de los puertos USB no es del todo óptima.

Te recuerdo también que no hay soporte para la WiFi, ni parece ser que lo haya.

Saludos.

Sekmeth · « **Respuesta #521 en:** 13-10-2014, 01:24 (Lunes) »

Muchas gracias por tus respuestas.

Mi conexión ADSL actual es Jazztel y conectado al router (AR5381u) tengo un PC dedicado al torrent (utorrent) y a jdownloader (mega, bitshare, etc.).

Mi intención sería sustituir todo eso por un Livebox 2.1 con el OpenWRT y un hdd externo por usb, y dejar que el router se encargase de las descargas, eliminando así al pc dedicado y ahorrando unos wattios de la luz

El tema del módem lo saco porque por diversos foros he leido que este router con el stock firmware es... una caca. Tiene cuelgues varios, inestabilidad en lal línea, y quería saber si al pasar a OpenWRT este tipo de incidencias seguían presentes o si quedaban ya resueltas.

fhocorp · « **Respuesta #522 en:** 29-10-2014, 23:19 (Miércoles) »

Hello

Thanks for your Work

I am trying to flash the u-boot at Step 2 "Instalacion"

Citar

Pulsamos "U" para cargar el uboot

Código:
[VR9 Boot]:U
   UPLOAD Flash
   ---------------------------------------
   Area Address Length
   ---------------------------------------

Boot 0xB0000000 512K
[1] Image 0 0xB1280000 6144K
   [2] Image 1 0xB1880000 6144K
   [3] Configuration 0xB1E80000 1024K
   [4] Boot Parameters 0xB1F80000 256K
   [5] Flash Image 0xB0000000 32768K
   [6] Linux Image 0xB0080000 24576K
   [7] Emergency Value 0xB1FC0000 2883584K
   ---------------------------------------
   Enter area to UPLOAD: 0
   Upload area 0. Are you sure? (Y/n)
Pulsamos "Y" y mandamos por X-modem la imagen de uboot

Where i can download u-boot-V11.bin or u-boot-V12.bin ??

What is the u-boot file used for this step ? ??? This file ? openwrt-lantiq-arv7519rw22_nor-u-boot.img ???

beghiero · « **Respuesta #523 en:** 16-11-2014, 21:42 (Domingo) »

Hello. Sorry for not writing in castellano. I'm Italian, and I understand almost all written in castellano, but I'm not able to write...

Bought an ARV7516RW22 on Ebay.
Followed all instructions on first message without problems.
The firmware on first message works very well, but no more 'packages' available online...
The firmware on Barrier Breaker trunk, instead, works almost completely, but ethernet ports only seems to work at mac-address level, not IP, so is not usable, at least on my router (V1.1).
I compiled the current snapshot firmware (r43236), that works perfectly (still lack of WiFi and VoIP....) and now I'm using it as my DSL modem.
This message only to thank you all and to let you know the problem on trunk firmware...

Ciao, Piero.

moonrotation · « **Respuesta #524 en:** 18-11-2014, 19:05 (Martes) »

Hola. Gran trabajo con el tutorial.

Ando desesperado porque no logro uno de los pasos.
Os explico. Tengo el serial ya soldado y funcionando en hyperterminal, pero cuando intento pulsar espacio o alguna tecla no hace nada.

El cable que use es el CA-42 de nokia, que porcierto le he tenido que conectar el VCC ya que sin el no funciona (Antes de nada comprobe que el voltaje fuera de 3.3v).

He conprobado y resoldado el cable tx y sigo igual. Mis soldaduras no es que sean muy buenas pero siempre me ha funcionado a la primera con mi wrt610nv2 y mi e3000.

Código: [Seleccionar]

pciauto_bus_scan : pci_devfn 57
pciauto_bus_scan : pci_devfn 58
pciauto_bus_scan : pci_devfn 59
pciauto_bus_scan : pci_devfn 5a
pciauto_bus_scan : pci_devfn 5b
pciauto_bus_scan : pci_devfn 5c
pciauto_bus_scan : pci_devfn 5d
pciauto_bus_scan : pci_devfn 5e
pciauto_bus_scan : pci_devfn 5f
pciauto_bus_scan : pci_devfn 60
pciauto_bus_scan : pci_devfn 61
pciauto_bus_scan : pci_devfn 62
pciauto_bus_scan : pci_devfn 63
pciauto_bus_scan : pci_devfn 64
pciauto_bus_scan : pci_devfn 65
pciauto_bus_scan : pci_devfn 66
pciauto_bus_scan : pci_devfn 67
pciauto_bus_scan : pci_devfn 68
pciauto_bus_scan : pci_devfn 69
pciauto_bus_scan : pci_devfn 6a
pciauto_bus_scan : pci_devfn 6b
pciauto_bus_scan : pci_devfn 6c
pciauto_bus_scan : pci_devfn 6d
pciauto_bus_scan : pci_devfn 6e
pciauto_bus_scan : pci_devfn 6f
pciauto_bus_scan : pci_devfn 70
pciauto_bus_scan : pci_devfn 71
pciauto_bus_scan : pci_devfn 72
pciauto_bus_scan : pci_devfn 73
pciauto_bus_scan : pci_devfn 74
pciauto_bus_scan : pci_devfn 75
pciauto_bus_scan : pci_devfn 76
pciauto_bus_scan : pci_devfn 77
pciauto_bus_scan : pci_devfn 78
pciauto_bus_scan : pci_devfn 79
pciauto_bus_scan : pci_devfn 7a
pciauto_bus_scan : pci_devfn 7b
pciauto_bus_scan : pci_devfn 7c
pciauto_bus_scan : pci_devfn 7d
pciauto_bus_scan : pci_devfn 7e
pciauto_bus_scan : pci_devfn 7f
pciauto_bus_scan : pci_devfn 80
pciauto_bus_scan : pci_devfn 81
pciauto_bus_scan : pci_devfn 82
pciauto_bus_scan : pci_devfn 83
pciauto_bus_scan : pci_devfn 84
pciauto_bus_scan : pci_devfn 85
pciauto_bus_scan : pci_devfn 86
pciauto_bus_scan : pci_devfn 87
pciauto_bus_scan : pci_devfn 88
pciauto_bus_scan : pci_devfn 89
pciauto_bus_scan : pci_devfn 8a
pciauto_bus_scan : pci_devfn 8b
pciauto_bus_scan : pci_devfn 8c
pciauto_bus_scan : pci_devfn 8d
pciauto_bus_scan : pci_devfn 8e
pciauto_bus_scan : pci_devfn 8f
pciauto_bus_scan : pci_devfn 90
pciauto_bus_scan : pci_devfn 91
pciauto_bus_scan : pci_devfn 92
pciauto_bus_scan : pci_devfn 93
pciauto_bus_scan : pci_devfn 94
pciauto_bus_scan : pci_devfn 95
pciauto_bus_scan : pci_devfn 96
pciauto_bus_scan : pci_devfn 97
pciauto_bus_scan : pci_devfn 98
pciauto_bus_scan : pci_devfn 99
pciauto_bus_scan : pci_devfn 9a
pciauto_bus_scan : pci_devfn 9b
pciauto_bus_scan : pci_devfn 9c
pciauto_bus_scan : pci_devfn 9d
pciauto_bus_scan : pci_devfn 9e
pciauto_bus_scan : pci_devfn 9f
pciauto_bus_scan : pci_devfn a0
pciauto_bus_scan : pci_devfn a1
pciauto_bus_scan : pci_devfn a2
pciauto_bus_scan : pci_devfn a3
pciauto_bus_scan : pci_devfn a4
pciauto_bus_scan : pci_devfn a5
pciauto_bus_scan : pci_devfn a6
pciauto_bus_scan : pci_devfn a7
pciauto_bus_scan : pci_devfn a8
pciauto_bus_scan : pci_devfn a9
pciauto_bus_scan : pci_devfn aa
pciauto_bus_scan : pci_devfn ab
pciauto_bus_scan : pci_devfn ac
pciauto_bus_scan : pci_devfn ad
pciauto_bus_scan : pci_devfn ae
pciauto_bus_scan : pci_devfn af
pciauto_bus_scan : pci_devfn b0
pciauto_bus_scan : pci_devfn b1
pciauto_bus_scan : pci_devfn b2
pciauto_bus_scan : pci_devfn b3
pciauto_bus_scan : pci_devfn b4
pciauto_bus_scan : pci_devfn b5
pciauto_bus_scan : pci_devfn b6
pciauto_bus_scan : pci_devfn b7
pciauto_bus_scan : pci_devfn b8
pciauto_bus_scan : pci_devfn b9
pciauto_bus_scan : pci_devfn ba
pciauto_bus_scan : pci_devfn bb
pciauto_bus_scan : pci_devfn bc
pciauto_bus_scan : pci_devfn bd
pciauto_bus_scan : pci_devfn be
pciauto_bus_scan : pci_devfn bf
pciauto_bus_scan : pci_devfn c0
pciauto_bus_scan : pci_devfn c1
pciauto_bus_scan : pci_devfn c2
pciauto_bus_scan : pci_devfn c3
pciauto_bus_scan : pci_devfn c4
pciauto_bus_scan : pci_devfn c5
pciauto_bus_scan : pci_devfn c6
pciauto_bus_scan : pci_devfn c7
pciauto_bus_scan : pci_devfn c8
pciauto_bus_scan : pci_devfn c9
pciauto_bus_scan : pci_devfn ca
pciauto_bus_scan : pci_devfn cb
pciauto_bus_scan : pci_devfn cc
pciauto_bus_scan : pci_devfn cd
pciauto_bus_scan : pci_devfn ce
pciauto_bus_scan : pci_devfn cf
pciauto_bus_scan : pci_devfn d0
pciauto_bus_scan : pci_devfn d1
pciauto_bus_scan : pci_devfn d2
pciauto_bus_scan : pci_devfn d3
pciauto_bus_scan : pci_devfn d4
pciauto_bus_scan : pci_devfn d5
pciauto_bus_scan : pci_devfn d6
pciauto_bus_scan : pci_devfn d7
pciauto_bus_scan : pci_devfn d8
pciauto_bus_scan : pci_devfn d9
pciauto_bus_scan : pci_devfn da
pciauto_bus_scan : pci_devfn db
pciauto_bus_scan : pci_devfn dc
pciauto_bus_scan : pci_devfn dd
pciauto_bus_scan : pci_devfn de
pciauto_bus_scan : pci_devfn df
pciauto_bus_scan : pci_devfn e0
pciauto_bus_scan : pci_devfn e1
pciauto_bus_scan : pci_devfn e2
pciauto_bus_scan : pci_devfn e3
pciauto_bus_scan : pci_devfn e4
pciauto_bus_scan : pci_devfn e5
pciauto_bus_scan : pci_devfn e6
pciauto_bus_scan : pci_devfn e7
pciauto_bus_scan : pci_devfn e8
pciauto_bus_scan : pci_devfn e9
pciauto_bus_scan : pci_devfn ea
pciauto_bus_scan : pci_devfn eb
pciauto_bus_scan : pci_devfn ec
pciauto_bus_scan : pci_devfn ed
pciauto_bus_scan : pci_devfn ee
pciauto_bus_scan : pci_devfn ef
pciauto_bus_scan : pci_devfn f0
pciauto_bus_scan : pci_devfn f1
pciauto_bus_scan : pci_devfn f2
pciauto_bus_scan : pci_devfn f3
pciauto_bus_scan : pci_devfn f4
pciauto_bus_scan : pci_devfn f5
pciauto_bus_scan : pci_devfn f6
pciauto_bus_scan : pci_devfn f7
pciauto_bus_scan : pci_devfn f8
pciauto_bus_scan : pci_devfn f9
pciauto_bus_scan : pci_devfn fa
pciauto_bus_scan : pci_devfn fb
pciauto_bus_scan : pci_devfn fc
pciauto_bus_scan : pci_devfn fd
pciauto_bus_scan : pci_devfn fe
after pciauto_assign_resources ???
Scanning bus 00
pci_type=1 in pci_scan_slot
pci_type=1
dev->pci_type=1
Found 00:00 [1bef/0011] 000600 01
Early fixups, before probing the BARs !!!
PCI: Calling quirk 803A508C for 00:00.0
ifx_pcie_write_config : bus_number = 0 ????
PCI: 00:00.0: class 600 doesn't match header type 01. Ignoring class.
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
Fixups for bus 00
Scanning behind PCI bridge 00:00.0, config ff0100, pass 0
ifx_pcie_write_config : bus_number = 0 ????
Scanning behind PCI bridge 00:00.0, config ff0100, pass 1
ifx_pcie_write_config : bus_number = 0 ????
ifx_pcie_write_config : bus_number = 0 ????
ifx_pcie_write_config : bus_number = 0 ????
ifx_pcie_write_config : bus_number = 0 ????
Scanning bus 01
pci_type=1 in pci_scan_slot
pci_type=1
dev->pci_type=1
Found 01:00 [1a30/0710] 000d80 00
Early fixups, before probing the BARs !!!
PCI: Calling quirk 803A508C for 01:00.0
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
pci_type=1 in pci_scan_slot
Fixups for bus 01
Bus scan for 01 returning with max=01
ifx_pcie_write_config : bus_number = 0 ????
ifx_pcie_write_config : bus_number = 0 ????
ifx_pcie_write_config : bus_number = 0 ????
Bus scan for 00 returning with max=01
IrqConnect : IRQ = 97, Handler = 0x803A59FC
[KERN_INFO]IFX PCIe Root Complex driver, version 1.1.4, (c)2009 Infineon Technol
ogies AG
PCI: Calling quirk 803A5D7C for 01:00.0
check dev->cfg_size <= 256 ???????
pcie_set_readrq : rq 80
pcie_set_readrq : ctl 1f
msi_set_enable is called ???
arch_setup_msi_irqs(236) is called
set_irq_msi : entry 85ddf7dc irq 155
call set_irq_msi ????
get_irq_msi i 0 irq 155 : entry 85ddf7dc irq 155
get_irq_msi return 85ddf7dc
call get_irq_msi ????
pci_intx_for_msi is called ????
pci_intx_for_msi is called ????
pci_intx: enable 0
msi_set_enable is called ???
pci_init 2
pci_find_slot bus 1 devfn 0
dev->bus->number 0 dev->devfn 0
dev->bus->number 1 dev->devfn 0
PCI_AH_probe: Vendor_id=1A30,Device_id=710
[HWLAN] devtag = 00000000
[HWLAN] Vendor ID 0x1a30
[HWLAN] Device ID 0x710
[HWLAN] Base Addr 0xb8000000
[HWLAN] SVendor ID 0x1a30
[HWLAN] SDevice ID 0x711
[HWLAN] Revision ID 0x1
[HWLAN] interrupt vector 0x1
Find PCI/PCIe interface at info=2 in tag=0
[0]install irq 155
IrqConnect : IRQ = 155, Handler = 0x80134F9C
[40] Allocate resource 204, FreeResource = 51
pci_announce_device called
pci_announce_device called
set pci_type to 1
dev=0x81bd8fe4 in _mtlk_pci_init
dev->pci_type=1
pcibios_set_master> lat=0x0
PCI: Setting latency timer of device 01:00.0 to 64
alloc_etherdev: name = wlan0
alloc_etherdev> dev->priv = 0x8144BEF4 **********

Get wlan0 dev=82BD7DA8
[40] Allocate event 360
[40] Allocate event 361
[40] Allocate event 362
[40] Allocate event 363
[40] Allocate event 364
[40] Allocate event 365
[40] Allocate event 366
[40] Allocate event 367
[40] Allocate event 368
[40] Allocate event 369
[40] Allocate event 370
[40] Allocate event 371
[40] Allocate event 372
[40] Allocate event 373
[40] Allocate event 374
[40] Allocate event 375
[40] Allocate event 376
[40] Allocate event 377
[40] Allocate event 378
[40] Allocate event 379
[40] Allocate event 380
[40] Allocate event 381
[40] Allocate event 382
[40] Allocate event 383
[40] Allocate event 384
[40] Allocate event 385
[40] Allocate event 386
[40] Allocate event 387
[40] Allocate event 388
[40] Allocate event 389
[40] Allocate event 390
[40] Allocate event 391
[40] Allocate event 392
[40] Allocate event 393
[40] Allocate event 394
[40] Allocate event 395
[40] Allocate event 396
[40] Allocate event 397
[40] Allocate event 398
[40] Allocate event 399
[40] Allocate event 400
[40] Allocate event 401
[40] Allocate event 402
[40] Allocate event 403
[40] Allocate event 404
[40] Allocate event 405
[40] Allocate event 406
[40] Allocate event 407
[40] Allocate event 408
[40] Allocate event 409
[40] Allocate event 410
[40] Allocate event 411
[40] Allocate event 412
[40] Allocate event 413
[40] Allocate event 414
[40] Allocate event 415
[40] Allocate event 416
[40] Allocate event 417
[40] Allocate event 418
[40] Allocate event 419
[40] Allocate event 420
[40] Allocate event 421
[40] Allocate event 422
[40] Allocate event 423
[40] Allocate event 424
[40] Allocate event 425
[40] Allocate event 426
[40] Allocate event 427
[40] Allocate resource 205, FreeResource = 52
[40] Allocate event 428
[40] Allocate event 429
[40] Allocate event 430
[40] Allocate resource 206, FreeResource = 53
[40] Allocate event 431
[40] Allocate event 432
[40] Allocate event 433
ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.1.0_Customers_r907 MIPS:
 Upper CPU(TMC AGG AP) interface: PCI  phy type: real phy on Nov 14 2012 at 11:0
3:45@@@ END @@@
contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.1.0_Customers_r907 MIPS:
 Lower MAC  interface: --  phy type: real phy on Nov 14 2012 at 11:03:40@@@ END
@@@
mtlk_core_start : nic 8144bef4 , hw 8144c4c4
[40] Allocate event 434
[40] Allocate event 435
[40] Allocate event 436
[40] Allocate resource 207, FreeResource = 54
[40] Allocate event 437
create mtlk kernel thread 8144bec8
running  mtlk kernel thread 8144bec8
RUNTASK id=66(osdep 8144bec8) Metalink kernel thread ...
Finish pci init sys_time=17466
[reset_802dot1x] wireless module ready
init_wpa
111111111=>configp->enableSSN =1
wpa2flag=6
wpa2flag=2
111111111=>configp->enableSSN =3
ie_set==>
ie_set!
enableSSN=3,SSNPSK=1
WPA ie built!!!!!
blob_set_attachment
i_set over
gtk_setkeys
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
[reset_802dot1x] 802.1Xv2 ready
[htf_dbg]     - OnlineActiveWirless() 641
mtlk dev_close ====>>>
[eric_dbg]     - Set1Xconfig() 114
nRadio =0
[eric_dbg]     -Set1Xconfig to set WPA2/WPA,but no need in wave300
===============OnlineActiveWirless to set RSN ie==============
===============OnlineActiveWirless to set RSN ie over==============
mtlk dev_open ====>>>
=================RSN check!!!==============================
=================RSN check over!!!==============================
ifno2dot1x_if[2]=0
ifno2dot1x_if[23]=81
dot1x_wireless_if_mask=0x800004
[reset_802dot1x] wireless module ready
init_wpa
111111111=>configp->enableSSN =1
wpa2flag=6
wpa2flag=2
111111111=>configp->enableSSN =3
ie_set==>
ie_set!
enableSSN=3,SSNPSK=1
WPA ie built!!!!!
blob_set_attachment
i_set over
gtk_setkeys
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
111111111=>configp->enableSSN =0
[reset_802dot1x] 802.1Xv2 ready
[onlineActive_mgmt_access]726 op:0*********************************************
****Wi-Fi Simple Config Application*****
Version: Build 2.02.2.DTM1.1, Feb  8 2013 21:29:27
*********************************************
@#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@
Entered udp_read
wsc_Send_UPNP_packet> enter
wsc_Send_eap_packet:udpFdupnp_wcn:2b;;udpFdupnp:2d
*******wlan_update_appie start***********
Config Method:0x84
pCurr->eventWaitQueue=139
>>>>>>>>>>>Reboot on training timeout<<<<<<<<<
DSL[00]: Reboot on training timeout (120)!!!
Autoboot State: Restart
pCurr->eventWaitQueue=139
Autoboot State: FirmwareRequest
Autoboot State: FirmwareWait
pCurr->eventWaitQueue=139
pCurr->eventWaitQueue=139
StatusData.nStatus=3


@@@@@@@@@@@@@ DSL_CPE_DownloadFirmware() @@@@@@@@@@@@@
nFwReqType = 3, Fw name1=NULL, name2=NULL

DSL_CPE: Using normal fw download...
pCurr->eventWaitQueue=139
DSL_FW_REQUEST_ADSL in DSL_DRV_DEV_FwDownload
hwVers=0x230
hwVers=0x230
MEI_InternalFirmwareDownload called
pCurr->eventWaitQueue=139
Autoboot State: firmwareReady
pCurr->eventWaitQueue=139
Autoboot State: Init
pCurr->eventWaitQueue=139
StatusData.nStatus=2
set dms 67C3 1B 1 2300
nReturn=0 nData="67C3 001B 0001 "
pCurr->eventWaitQueue=139
Autoboot State: Train
modem state = 00000100
[xDSL] vinax_modem_state = 0x0100
modem state = 00000200

rulasss · « **Respuesta #525 en:** 18-11-2014, 19:16 (Martes) »

Una preguntilla sobre este cacharro. Como va el tema del voip y el wifi, ¿es plausible que de puedan usar en un tiempo o es como otros muchos que no hay driver liberado?

fhocorp · « **Respuesta #526 en:** 18-11-2014, 23:31 (Martes) »

Hello

Someone can send me the original orange livebox 2.1 firmware ?

No telnet ?? No VoIP config page ??

moonrotation · « **Respuesta #527 en:** 21-11-2014, 11:03 (Viernes) »

Bueno ya eh resuelto el problema. Ahora me han surgido varios mas.

EL u-boot que esta en el primer pors solo me detecta 64MB de ram en el v1.2. Tube que utilizar uno buscando por todo el post.
Openwrt tiene soporte para este router, pero xq no funciona? Las ultimas versiones de Barrier Breaker no tienen ethernet y las del trunk nisiquiera arrancan.

Mi ticket: https://dev.openwrt.org/ticket/18372
y otro ticket parecido: https://dev.openwrt.org/ticket/17391

Alguna manera de compilar las ultimas versiones para este router? Necesito hacer mis propias builds personalizadas.

Porfavor si alguien me puede ayudar. LLevo 3 dias y mi pc compila en menos de 10 minutos

Pteridium · « **Respuesta #528 en:** 21-11-2014, 14:53 (Viernes) »

Cita de: moonrotation en 21-11-2014, 11:03 (Viernes)

Bueno ya eh resuelto el problema. Ahora me han surgido varios mas.

EL u-boot que esta en el primer pors solo me detecta 64MB de ram en el v1.2. Tube que utilizar uno buscando por todo el post.
Openwrt tiene soporte para este router, pero xq no funciona? Las ultimas versiones de Barrier Breaker no tienen ethernet y las del trunk nisiquiera arrancan.

Mi ticket: https://dev.openwrt.org/ticket/18372
y otro ticket parecido: https://dev.openwrt.org/ticket/17391

Alguna manera de compilar las ultimas versiones para este router? Necesito hacer mis propias builds personalizadas.

Porfavor si alguien me puede ayudar. LLevo 3 dias y mi pc compila en menos de 10 minutos

De momento el repo de openwrt-es es el único en el que funcionan los puertos de red:

Código: [Seleccionar]

git clone https://github.com/openwrt-es/openwrt -b bb-14.07-rc3¿Alguna razón en particular para necesitar trunk? Barrier Breaker es bastante estable.

moonrotation · « **Respuesta #529 en:** 21-11-2014, 15:00 (Viernes) »

Cita de: Pteridium en 21-11-2014, 14:53 (Viernes)

Cita de: moonrotation en 21-11-2014, 11:03 (Viernes)
Bueno ya eh resuelto el problema. Ahora me han surgido varios mas.

EL u-boot que esta en el primer pors solo me detecta 64MB de ram en el v1.2. Tube que utilizar uno buscando por todo el post.
Openwrt tiene soporte para este router, pero xq no funciona? Las ultimas versiones de Barrier Breaker no tienen ethernet y las del trunk nisiquiera arrancan.

Mi ticket: https://dev.openwrt.org/ticket/18372
y otro ticket parecido: https://dev.openwrt.org/ticket/17391

Alguna manera de compilar las ultimas versiones para este router? Necesito hacer mis propias builds personalizadas.

Porfavor si alguien me puede ayudar. LLevo 3 dias y mi pc compila en menos de 10 minutos
De momento el repo de openwrt-es es el único en el que funcionan los puertos de red:
Código: [Seleccionar]
git clone https://github.com/openwrt-es/openwrt -b bb-14.07-rc3¿Alguna razón en particular para necesitar trunk? Barrier Breaker es bastante estable.

Gracias por tu pronta respuesta. Finalmente he logrado compilar una build funcional del trunk. Simplemente he cambiado la version del kernel a 3.10 y he removido el parche: 0208-lantiq-xrx200-strip-fcs.patch

moonrotation · « **Respuesta #530 en:** 22-11-2014, 13:37 (Sábado) »

Mas avances!! he logrado hacer que funcione en Barrier Breaker desde el git oficial.
Simplemente hay que borrar el parche: 0202-owrt-lantiq-multiple-flash.parch <- Culpable!!

De esta manera ya arranca sin problemas. Los puertos lan funcionan tambien.

Ahora estoy haciendo pruebas con el trunk y el kernel 3.14, a ver si de esta manera funcionan mejor los wireless usb.

Código: [Seleccionar]

[    0.000000] Linux version 3.10.49 (kool@ubuntu-10) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43321) ) 
#1 Thu Nov 20 10:29:34 WET 2014
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 803e09d0, node_mem_map 810034c0
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=000084a0
[    0.000000] Readback ErrCtl register=000084a0
[    0.000000] Memory: 125372k/131072k available (3046k kernel code, 5700k reserved, 1031k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.028000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.064000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.068000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.180000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.280000] ifx_pcie_wait_phy_link_up timeout
[    0.284000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.396000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.496000] ifx_pcie_wait_phy_link_up timeout
[    0.500000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.612000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.712000] ifx_pcie_wait_phy_link_up timeout
[    0.716000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.828000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.928000] ifx_pcie_wait_phy_link_up timeout
[    0.932000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    1.044000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    1.144000] ifx_pcie_wait_phy_link_up timeout
[    1.148000] pcie_rc_initialize link up failed!!!!!
[    1.164000] bio: create slab <bio-0> at 0
[    1.168000] usbcore: registered new interface driver usbfs
[    1.172000] usbcore: registered new interface driver hub
[    1.176000] usbcore: registered new device driver usb
[    1.180000] Switching to clocksource MIPS
[    1.188000] NET: Registered protocol family 2
[    1.192000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    1.200000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.204000] TCP: Hash tables configured (established 1024 bind 1024)
[    1.212000] TCP: reno registered
[    1.216000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.220000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.228000] NET: Registered protocol family 1
[    1.232000] PCI: CLS 0 bytes, default 32
[    1.232000] gptu: totally 6 16-bit timers/counters
[    1.236000] gptu: misc_register on minor 63
[    1.240000] gptu: succeeded to request irq 126
[    1.244000] gptu: succeeded to request irq 127
[    1.248000] gptu: succeeded to request irq 128
[    1.256000] gptu: succeeded to request irq 129
[    1.260000] gptu: succeeded to request irq 130
[    1.264000] gptu: succeeded to request irq 131
[    1.272000] phy-xrx200 gphy-xrx200.4: requesting lantiq/vr9_phy22f_a2x.bin
[    1.276000] phy-xrx200 gphy-xrx200.4: booting GPHY0 firmware at 78C0000
[    1.284000] phy-xrx200 gphy-xrx200.4: booting GPHY1 firmware at 78C0000
[    1.392000] Wired TLB entries for Linux read_c0_wired() = 0
[    1.396000] config3 0x2424 MT 1
[    1.396000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    1.396000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    1.416000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.432000] msgmni has been set to 244
[    1.436000] io scheduler noop registered
[    1.440000] io scheduler deadline registered (default)
[    1.444000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    1.452000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.468000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    1.476000] Amd/Fujitsu Extended Query Table at 0x0040
[    1.480000]   Amd/Fujitsu Extended Query version 1.3.
[    1.484000] number of CFI chips: 1
[    1.488000] 5 ofpart partitions found on MTD device ltq_nor
[    1.496000] Creating 5 MTD partitions on "ltq_nor":
[    1.500000] 0x000000000000-0x000000060000 : "uboot"
[    1.504000] 0x000000060000-0x000000080000 : "uboot-env"
[    1.512000] 0x000000080000-0x000001e80000 : "firmware"
[    1.516000] 0x0000001e14c8-0x000001e80000 : "rootfs"
[    1.520000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.536000] mtd: device 3 (rootfs) set to be root filesystem
[    1.540000] mtd: partition "rootfs_data" created automatically, ofs=0x3c0000, len=0x1ac0000
[    1.548000] 0x0000003c0000-0x000001e80000 : "rootfs_data"
[    1.572000] 0x000001e80000-0x000001f80000 : "dsl_fw"
[    1.576000] 0x000001f80000-0x000002000000 : "boardconfig"
[    1.692000] libphy: lantiq,xrx200-mdio: probed
[    1.696000] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    1.704000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13, irq=-1)
[    1.712000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14, irq=-1)
[    1.720000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11, irq=-1)
[    1.728000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12, irq=-1)
[    1.736000] wdt 1f8803f0.watchdog: Init done
[    1.740000] leds-gpio gpio-leds.6: pins are not configured from the driver
[    1.748000] TCP: cubic registered
[    1.752000] NET: Registered protocol family 17
[    1.756000] 8021q: 802.1Q VLAN Support v1.8
[    1.764000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.776000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.784000] Freeing unused kernel memory: 200K (803fe000 - 80430000)
[    3.796000] eth0: port 4 got link
[    3.900000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[    3.908000] Chip Version :000b BurstSize=4
[    4.508000] IFXUSB: USB core #0 soft-reset
[    4.812000] IFXUSB: USB core #0 soft-reset
[    4.816000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    4.820000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[    4.828000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[    4.832000] IFXUSB: Init: Power Port (0)
[    4.840000] hub 1-0:1.0: USB hub found
[    4.840000] hub 1-0:1.0: 1 port detected
[    5.344000] IFXUSB: USB core #1 soft-reset
[    5.648000] IFXUSB: USB core #1 soft-reset
[    5.652000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    5.656000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[    5.664000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[    5.668000] IFXUSB: Init: Power Port (0)
[    5.676000] hub 2-0:1.0: USB hub found
[    5.676000] hub 2-0:1.0: 1 port detected
[    5.680000] ifxusb_hcd ifxusb_hcd: requested GPIO 232
[    9.300000] jffs2: notice: (283) jffs2_build_xattr_subsystem: complete building xattr subsystem, 
1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 0 orphan) found.
[   10.788000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[   10.788000] 
[   10.860000] NET: Registered protocol family 10
[   10.868000] NET: Registered protocol family 8
[   10.872000] NET: Registered protocol family 20
[   10.884000] PPP generic driver version 2.4.2
[   10.896000] nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
[   10.908000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.924000] MEI CPE Driver, Version 1.2.0
[   10.924000] 
[   10.928000] (c) Copyright 2009, Infineon Technologies AG
[   10.928000] 
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
[   10.932000] 
[   10.932000] 
[   10.932000] Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   10.948000] 
[   10.948000] Predefined debug level: 2
[   10.964000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.976000] Infineon Technologies DEU driver version 2.0.0 
[   10.980000] IFX DEU DES initialized (multiblock).
[   10.984000] IFX DEU AES initialized (multiblock).
[   10.988000] IFX DEU ARC4 initialized (multiblock).
[   10.992000] IFX DEU SHA1 initialized.
[   10.996000] IFX DEU MD5 initialized.
[   11.000000] IFX DEU SHA1_HMAC initialized.
[   11.004000] IFX DEU MD5_HMAC initialized.
[   11.028000] NET: Registered protocol family 24
[   11.048000] xt_time: kernel timezone is -0000
[   14.936000] jffs2: notice: (640) jffs2_build_xattr_subsystem: complete building xattr subsystem, 
1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
[   16.256000] device eth0 entered promiscuous mode
[   16.268000] br-lan: port 1(eth0) entered forwarding state
[   16.272000] br-lan: port 1(eth0) entered forwarding state
[   18.276000] br-lan: port 1(eth0) entered forwarding state

Con esto he resulto el maldito mensaje: VFS: Cannot open root device...

Tki2000: Editado porque descuadraba mucho el foro

moonrotation · « **Respuesta #531 en:** 22-11-2014, 17:26 (Sábado) »

He logrado compilar desde tunk una version 100% funcional y con multithreading.

Sin multithreading

Código: [Seleccionar]

VR9 rev 1.2 | ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT | MIPS 34Kc V5.6 | 332.54 | 1.0.1j |
 25694880 | 16867330 | 8063320 | 3592190 | 4230490 | 1518250 | 6488410 | 5588650 | 4904960 | 5.8 | 201.3 20.4 | 16.8 |

Con multithreading

Código: [Seleccionar]

VR9 rev 1.2 | ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT | MIPS 34Kc V5.6 | 332.54 | MIPS 34Kc V5.6 | 251.90 | 1.0.1j |
 25204390 | 15248380 | 7360130 | 3196660 | 3770310 | 1358850 | 5791740 | 4962300 | 4359170 | 5.2 | 178.4 18.0 | 14.7 |

Código: [Seleccionar]

[    0.000000] Linux version 3.14.18 (kool@ubuntu-10) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43336) ) 
#1 SMP Thu Nov 20 12:57:37 WET 2014
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 8044b4a0, node_mem_map 810033c0
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] Detected 1 available secondary CPU(s)       <-- Detectado segundo CPU
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] PERCPU: Embedded 7 pages/cpu @81106000 s6464 r8192 d14016 u32768
[    0.000000] pcpu-alloc: s6464 r8192 d14016 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00008428
[    0.000000] Readback ErrCtl register=00008428
[    0.000000] Memory: 124940K/131072K available (3402K kernel code, 160K rwdata, 912K rodata, 180K init, 208K bss, 6132K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] Setting up IPI vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.028000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] CPU1 revision is: 00019556 (MIPS 34Kc)
[    0.044000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.044000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.088000] Synchronize counters for CPU 1: done.
[    0.092000] Brought up 2 CPUs                          <-- Detectados 2 CPUs
[    0.096000] pinctrl core: initialized pinctrl subsystem
[    0.100000] NET: Registered protocol family 16
[    0.116000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.120000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.128000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.132000] FPU Affinity set after 2008 emulations
[    0.152000] bio: create slab <bio-0> at 0
[    0.160000] usbcore: registered new interface driver usbfs
[    0.164000] usbcore: registered new interface driver hub
[    0.168000] usbcore: registered new device driver usb
[    0.172000] Switched to clocksource MIPS
[    0.180000] NET: Registered protocol family 2
[    0.184000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.192000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.200000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.204000] TCP: reno registered
[    0.208000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.216000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.220000] NET: Registered protocol family 1
[    0.224000] PCI: CLS 0 bytes, default 32
[    0.228000] gptu: totally 6 16-bit timers/counters
[    0.232000] gptu: misc_register on minor 63
[    0.236000] gptu: succeeded to request irq 126
[    0.240000] gptu: succeeded to request irq 127
[    0.244000] gptu: succeeded to request irq 128
[    0.248000] gptu: succeeded to request irq 129
[    0.252000] gptu: succeeded to request irq 130
[    0.260000] gptu: succeeded to request irq 131
[    0.264000] phy-xrx200 gphy-xrx200.4: requesting lantiq/vr9_phy22f_a2x.bin
[    0.272000] phy-xrx200 gphy-xrx200.4: booting GPHY0 firmware at 7960000
[    0.280000] phy-xrx200 gphy-xrx200.4: booting GPHY1 firmware at 7960000
[    0.392000] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.404000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.416000] msgmni has been set to 244
[    0.420000] io scheduler noop registered
[    0.424000] io scheduler deadline registered (default)
[    0.428000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.440000] console [ttyLTQ0] enabled
[    0.444000] bootconsole [early0] disabled
[    0.456000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.464000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.472000]   Amd/Fujitsu Extended Query version 1.3.
[    0.476000] number of CFI chips: 1
[    0.480000] 5 ofpart partitions found on MTD device ltq_nor
[    0.484000] Creating 5 MTD partitions on "ltq_nor":
[    0.488000] 0x000000000000-0x000000060000 : "uboot"
[    0.496000] 0x000000060000-0x000000080000 : "uboot-env"
[    0.504000] 0x000000080000-0x000001e80000 : "firmware"
[    0.508000] 0x000000200267-0x000001e80000 : "rootfs"
[    0.512000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.528000] mtd: device 3 (rootfs) set to be root filesystem
[    0.532000] 1 squashfs-split partitions found on MTD device rootfs
[    0.540000] 0x000000820000-0x000001e80000 : "rootfs_data"
[    0.564000] 0x000001e80000-0x000001f80000 : "dsl_fw"
[    0.568000] 0x000001f80000-0x000002000000 : "boardconfig"
[    0.688000] libphy: lantiq,xrx200-mdio: probed
[    0.760000] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    0.828000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13, irq=-1)
[    0.896000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14, irq=-1)
[    0.964000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11, irq=-1)
[    1.032000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12, irq=-1)
[    1.040000] wdt 1f8803f0.watchdog: Init done
[    1.048000] TCP: cubic registered
[    1.048000] NET: Registered protocol family 17
[    1.056000] 8021q: 802.1Q VLAN Support v1.8
[    1.064000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.076000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.080000] Freeing unused kernel memory: 180K (80463000 - 80490000)
[    2.992000] eth0: port 5 got link
[    4.340000] random: nonblocking pool is initialized
[    4.620000] SCSI subsystem initialized
[    4.628000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[    4.632000] Chip Version :000b BurstSize=4
[    5.240000] IFXUSB: USB core #0 soft-reset
[    5.548000] IFXUSB: USB core #0 soft-reset
[    5.548000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    5.556000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[    5.564000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[    5.568000] IFXUSB: Init: Power Port (0)
[    5.576000] hub 1-0:1.0: USB hub found
[    5.576000] hub 1-0:1.0: 1 port detected
[    6.084000] IFXUSB: USB core #1 soft-reset
[    6.392000] IFXUSB: USB core #1 soft-reset
[    6.392000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    6.400000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[    6.408000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[    6.412000] IFXUSB: Init: Power Port (0)
[    6.416000] hub 2-0:1.0: USB hub found
[    6.420000] hub 2-0:1.0: 1 port detected
[    6.424000] ifxusb_hcd ifxusb_hcd: requested GPIO 232
[    6.432000] usbcore: registered new interface driver usb-storage
[   11.780000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x20000
[   11.784000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   11.792000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  119.520000] jffs2: notice: (311) jffs2_build_xattr_subsystem: complete building xattr subsystem, 
0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  119.632000] jffs2: notice: (308) jffs2_build_xattr_subsystem: complete building xattr subsystem, 
0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  122.852000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[  122.852000] 
[  122.876000] NET: Registered protocol family 10
[  122.896000] NET: Registered protocol family 8
[  122.900000] NET: Registered protocol family 20
[  122.912000] PPP generic driver version 2.4.2
[  122.920000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[  122.940000] MEI CPE Driver, Version 1.2.0
[  122.940000] 
[  122.944000] (c) Copyright 2009, Infineon Technologies AG
[  122.944000] 
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
[  122.948000] 
[  122.948000] 
[  122.948000] Lantiq CPE API Driver version: DSL CPE API V4.11.4
[  122.968000] 
[  122.968000] Predefined debug level: 2
[  122.980000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2
[  122.984000] Backport generated by backports.git backports-20141023-2-g4ff890b
[  122.996000] ip_tables: (C) 2000-2006 Netfilter Core Team
[  123.008000] lib80211: common routines for IEEE802.11 drivers
[  123.012000] lib80211_crypt: registered algorithm 'NULL'
[  123.012000] lib80211_crypt: registered algorithm 'CCMP'
[  123.016000] lib80211_crypt: registered algorithm 'TKIP'
[  123.016000] lib80211_crypt: registered algorithm 'WEP'
[  123.020000] Infineon Technologies DEU driver version 2.0.0 
[  123.024000] IFX DEU DES initialized (multiblock).
[  123.028000] IFX DEU AES initialized (multiblock).
[  123.032000] IFX DEU ARC4 initialized (multiblock).
[  123.040000] IFX DEU SHA1 initialized.
[  123.040000] IFX DEU MD5 initialized.
[  123.044000] IFX DEU SHA1_HMAC initialized.
[  123.048000] IFX DEU MD5_HMAC initialized.
[  123.060000] nf_conntrack version 0.5.0 (1955 buckets, 7820 max)
[  123.108000] NET: Registered protocol family 24
[  123.132000] xt_time: kernel timezone is -0000
[  123.164000] cfg80211: Calling CRDA to update world regulatory domain
[  123.172000] cfg80211: World regulatory domain updated:
[  123.176000] cfg80211:  DFS Master region: unset
[  123.180000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[  123.192000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  123.200000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[  123.208000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[  123.216000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[  123.224000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  123.232000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[  123.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[  123.248000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[  123.348000] usbcore: registered new interface driver rt2800usb
[  123.360000] usbcore: registered new interface driver ath9k_htc
[  128.452000] jffs2: notice: (883) jffs2_build_xattr_subsystem: complete building xattr subsystem, 
1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
[  130.944000] device eth0 entered promiscuous mode
[  130.952000] br-lan: port 1(eth0) entered forwarding state
[  130.956000] br-lan: port 1(eth0) entered forwarding state
[  132.960000] br-lan: port 1(eth0) entered forwarding state

Tki2000: Editado porque descuadraba mucho el foro

Lesgar · « **Respuesta #532 en:** 22-11-2014, 17:46 (Sábado) »

Si la cuelgas la pruebo en mi Rev1.1

Pteridium · « **Respuesta #533 en:** 22-11-2014, 20:59 (Sábado) »

Cita de: moonrotation en 22-11-2014, 17:26 (Sábado)

He logrado compilar desde tunk una version 100% funcional y con multithreading.

Sin multithreading
Código: [Seleccionar]
VR9 rev 1.2 | ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT | MIPS 34Kc V5.6 | 332.54 | 1.0.1j | 25694880 | 16867330 | 8063320 | 3592190 | 4230490 | 1518250 | 6488410 | 5588650 | 4904960 | 5.8 | 201.3 20.4 | 16.8 |
Con multithreading
Código: [Seleccionar]
VR9 rev 1.2 | ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT | MIPS 34Kc V5.6 | 332.54 | MIPS 34Kc V5.6 | 251.90 | 1.0.1j | 25204390 | 15248380 | 7360130 | 3196660 | 3770310 | 1358850 | 5791740 | 4962300 | 4359170 | 5.2 | 178.4 18.0 | 14.7 |

Siento fastidiar pero aunque se puede puede compilar un kernel con multithreading habilitado no se gana nada. El problema es que uno de los hilos se queda saturado manejando interrupciones.
En el código fuente de Lantiq hay un parche para resolver ese problema pero está escrito para el kernel 2.6.32 y no hay tu tía a aplicarlo correctamente en kernels modernos.
http://pastebin.com/YkmW4YnX

moonrotation · « **Respuesta #534 en:** 22-11-2014, 22:19 (Sábado) »

Ya estube haciendo pruebas y desde que conecto un wifi usb se cuelga. Es una pena que no funcione.

seny · « **Respuesta #535 en:** 22-11-2014, 22:48 (Sábado) »

Hola, voy a ver si me animo con este router, tengo curiosidad de ver como funciona con mi adsl

Alguien ha conseguido que funcione el puerto gigabit? por lo que veo en los arranques que habeis colgado no aparece pero por si alguien lo ha intentado.

Saludos

moonrotation · « **Respuesta #536 en:** 24-11-2014, 12:57 (Lunes) »

Cita de: seny en 22-11-2014, 22:48 (Sábado)

Hola, voy a ver si me animo con este router, tengo curiosidad de ver como funciona con mi adsl

Alguien ha conseguido que funcione el puerto gigabit? por lo que veo en los arranques que habeis colgado no aparece pero por si alguien lo ha intentado.

Saludos

Hola. Si que funciona pero aun no he probado si lo hace como gigabit.

Pteridium · « **Respuesta #537 en:** 24-11-2014, 18:03 (Lunes) »

Cita de: moonrotation en 24-11-2014, 12:57 (Lunes)

Cita de: seny en 22-11-2014, 22:48 (Sábado)
Hola, voy a ver si me animo con este router, tengo curiosidad de ver como funciona con mi adsl

Alguien ha conseguido que funcione el puerto gigabit? por lo que veo en los arranques que habeis colgado no aparece pero por si alguien lo ha intentado.

Saludos

Hola. Si que funciona pero aun no he probado si lo hace como gigabit.

Sí, funciona como gigabit perfectamente.

seny · « **Respuesta #538 en:** 24-11-2014, 18:58 (Lunes) »

Pues perfecto y gracias por la info, modem adsl, puerto gigabit, ya se me estan poniendo los dientes largos

Ahora viene pregunta tonta, ejem.. como se hace el "corto en flash"?

moonrotation · « **Respuesta #539 en:** 24-11-2014, 19:05 (Lunes) »

Alguien sabe si hay alguna manera de hacer funcionar un wifi usb como ap?

En bb funciona con 2 ralink que tengo pero desde que le doy caña con speedtest por emplo ni llega a terminar el test.
Con chaos calmer ni siquiera me puedo conectar pero son visibles.

Tambien he visto que el netia spot tiene wifi funcional (wave300). He probado parte de este tutorial pero no entiendo muy bien, en luci aparece el dispositivo wifi pero no funciona.

Noticias:

Autor Tema: [Desarrollo] OpenWrt en ASTORIA ARV7519RW22 (Leído 513635 veces)

doblecero

Sekmeth

fhocorp

beghiero

moonrotation

rulasss

fhocorp

moonrotation

Pteridium

moonrotation

moonrotation

moonrotation

Lesgar

Pteridium

moonrotation

seny

moonrotation

Pteridium

seny

moonrotation