Pteridium, a mí sólo me tardó en arrancar 170 sg la primera vez tras la actualización del firm. Si quieres te paso un log del puerto serie en el arranque... Ya me dices.
Ahí va mi dmesg:
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.34 (taxodium@debian) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40335) ) #4 Mon Mar 31 20:01:00 CEST 2014
[ 0.000000] SoC: VR9 rev 1.1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019555 (MIPS 34Kc)
[ 0.000000] MIPS: machine is ARV7519 - Astoria Networks ARV7519RW22-A-LT
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803845d0, node_mem_map 81003180
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00032e04
[ 0.000000] Readback ErrCtl register=00032e04
[ 0.000000] Memory: 125776k/131072k available (2843k kernel code, 5296k reserved, 860k data, 188k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.028000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.040000] pinctrl core: initialized pinctrl subsystem
[ 0.044000] NET: Registered protocol family 16
[ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.064000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.068000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.180000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.280000] ifx_pcie_wait_phy_link_up timeout
[ 0.284000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.396000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.496000] ifx_pcie_wait_phy_link_up timeout
[ 0.500000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.612000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.712000] ifx_pcie_wait_phy_link_up timeout
[ 0.716000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.828000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.928000] ifx_pcie_wait_phy_link_up timeout
[ 0.932000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 1.044000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 1.144000] ifx_pcie_wait_phy_link_up timeout
[ 1.148000] pcie_rc_initialize link up failed!!!!!
[ 1.160000] bio: create slab <bio-0> at 0
[ 1.164000] usbcore: registered new interface driver usbfs
[ 1.168000] usbcore: registered new interface driver hub
[ 1.172000] usbcore: registered new device driver usb
[ 1.176000] Switching to clocksource MIPS
[ 1.184000] NET: Registered protocol family 2
[ 1.188000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 1.192000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.200000] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.208000] TCP: reno registered
[ 1.212000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.216000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.224000] NET: Registered protocol family 1
[ 1.228000] PCI: CLS 0 bytes, default 32
[ 1.228000] gptu: totally 6 16-bit timers/counters
[ 1.232000] gptu: misc_register on minor 63
[ 1.236000] gptu: succeeded to request irq 126
[ 1.240000] gptu: succeeded to request irq 127
[ 1.244000] gptu: succeeded to request irq 128
[ 1.248000] gptu: succeeded to request irq 129
[ 1.256000] gptu: succeeded to request irq 130
[ 1.260000] gptu: succeeded to request irq 131
[ 1.264000] phy-xrx200 gphy-xrx200.6: requesting lantiq/vr9_phy22f_a1x.bin
[ 1.272000] phy-xrx200 gphy-xrx200.6: booting GPHY0 firmware at 78C0000
[ 1.280000] phy-xrx200 gphy-xrx200.6: booting GPHY1 firmware at 78C0000
[ 1.388000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.392000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.404000] msgmni has been set to 245
[ 1.408000] io scheduler noop registered
[ 1.412000] io scheduler deadline registered (default)
[ 1.420000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 1.424000] console [ttyLTQ0] enabled, bootconsole disabled
[ 1.440000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 1.448000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.452000] Amd/Fujitsu Extended Query version 1.3.
[ 1.456000] number of CFI chips: 1
[ 1.460000] 4 ofpart partitions found on MTD device ltq_nor
[ 1.468000] Creating 4 MTD partitions on "ltq_nor":
[ 1.472000] 0x000000000000-0x000000060000 : "uboot"
[ 1.480000] 0x000000060000-0x000000080000 : "uboot_cfg"
[ 1.484000] 0x000000080000-0x000001f80000 : "firmware"
[ 1.488000] 0x0000001c1d39-0x000001f80000 : "rootfs"
[ 1.492000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.508000] mtd: device 3 (rootfs) set to be root filesystem
[ 1.512000] mtd: partition "rootfs_data" created automatically, ofs=0x5e0000, len=0x19a0000
[ 1.520000] 0x0000005e0000-0x000001f80000 : "rootfs_data"
[ 1.544000] 0x000001f80000-0x000002000000 : "boardconfig"
[ 1.656000] libphy: lantiq,xrx200-mdio: probed
[ 1.664000] net-xrx200: invalid MAC, using random
[ 1.668000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11, irq=-1)
[ 1.676000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13, irq=-1)
[ 1.684000] net-xrx200: invalid MAC, using random
[ 1.688000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[ 1.696000] wdt 1f8803f0.watchdog: Init done
[ 1.700000] leds-gpio gpio-leds.5: pins are not configured from the driver
[ 1.708000] TCP: cubic registered
[ 1.712000] NET: Registered protocol family 17
[ 1.716000] 8021q: 802.1Q VLAN Support v1.8
[ 1.728000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.732000] Freeing unused kernel memory: 188K (803a1000 - 803d0000)
[ 5.868000] SCSI subsystem initialized
[ 5.876000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 5.880000] Chip Version :01c0 BurstSize=0
[ 6.484000] IFXUSB: USB core #0 soft-reset
[ 6.788000] IFXUSB: USB core #0 soft-reset
[ 6.788000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 6.796000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 6.804000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 6.808000] IFXUSB: Init: Power Port (0)
[ 6.824000] hub 1-0:1.0: USB hub found
[ 6.824000] hub 1-0:1.0: 1 port detected
[ 7.328000] IFXUSB: USB core #1 soft-reset
[ 7.632000] IFXUSB: USB core #1 soft-reset
[ 7.636000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 7.640000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[ 7.648000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[ 7.652000] IFXUSB: Init: Power Port (0)
[ 7.660000] hub 2-0:1.0: USB hub found
[ 7.664000] hub 2-0:1.0: 1 port detected
[ 7.668000] ifxusb_hcd ifxusb_hcd: requested GPIO 232
[ 7.680000] usbcore: registered new interface driver usb-storage
[ 8.940000] jffs2: notice: (266) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (0 unchecked, 18 orphan) and 29 of xref (0 dead, 18 orphan) found.
[ 9.048000] jffs2: notice: (263) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (0 unchecked, 18 orphan) and 29 of xref (0 dead, 18 orphan) found.
[ 11.704000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 11.704000]
[ 11.720000] NET: Registered protocol family 8
[ 11.724000] NET: Registered protocol family 20
[ 11.744000] PPP generic driver version 2.4.2
[ 11.760000] MEI CPE Driver, Version 1.2.0
[ 11.760000]
[ 11.760000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
[ 11.768000]
[ 11.768000]
[ 11.768000] Lantiq CPE API Driver version: DSL CPE API V4.11.4
[ 11.784000]
[ 11.784000] Predefined debug level: 2
[ 11.796000] fuse init (API version 7.22)
[ 11.804000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[ 11.812000] Backport generated by backports.git backports-20140124-0-g1256d3e
[ 11.832000] ATM1.0.26 ATM (A1) firmware version 0.24
[ 11.836000] ifxmips_atm: ATM init succeed
[ 11.844000] Infineon Technologies DEU driver version 2.0.0
[ 11.856000] IFX DEU DES initialized (multiblock).
[ 11.864000] IFX DEU AES initialized (multiblock).
[ 11.868000] IFX DEU ARC4 initialized (multiblock).
[ 11.876000] IFX DEU SHA1 initialized.
[ 11.884000] IFX DEU MD5 initialized.
[ 11.884000] IFX DEU SHA1_HMAC initialized.
[ 11.888000] IFX DEU MD5_HMAC initialized.
[ 11.908000] genirq: Flags mismatch irq 96. 00000020 (ptm_mailbox_isr) vs. 00000020 (atm_mailbox_isr)
[ 11.916000] /home/taxodium/trunk/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:970:ifx_ptm_init: IRQ may be occupied by other driver, please reconfig to disable it.
[ 11.952000] ifxmips_ptm: PTM init failed
[ 11.964000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 11.992000] NET: Registered protocol family 24
[ 12.052000] xt_time: kernel timezone is -0000
[ 12.084000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.092000] cfg80211: World regulatory domain updated:
[ 12.096000] cfg80211: DFS Master region: unset
[ 12.100000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.108000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 12.116000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 12.124000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 12.128000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.136000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 12.144000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 12.156000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.176000] genirq: Flags mismatch irq 96. 00000020 (ptm_mailbox_isr) vs. 00000020 (atm_mailbox_isr)
[ 12.184000] /home/taxodium/trunk/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:970:ifx_ptm_init: IRQ may be occupied by other driver, please reconfig to disable it.
[ 12.220000] ifxmips_ptm: PTM init failed
[ 12.280000] usbcore: registered new interface driver p54usb
[ 12.300000] usbcore: registered new interface driver rt73usb
[ 12.312000] usbcore: registered new interface driver rtl8187
[ 12.396000] usbcore: registered new interface driver brcmfmac
[ 12.416000] usbcore: registered new interface driver carl9170
[ 12.432000] genirq: Flags mismatch irq 96. 00000020 (ptm_mailbox_isr) vs. 00000020 (atm_mailbox_isr)
[ 12.440000] /home/taxodium/trunk/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:970:ifx_ptm_init: IRQ may be occupied by other driver, please reconfig to disable it.
[ 12.480000] ifxmips_ptm: PTM init failed
[ 12.484000] usbcore: registered new interface driver rt2500usb
[ 12.500000] usbcore: registered new interface driver rt2800usb
[ 12.528000] usbcore: registered new interface driver ath9k_htc
[ 12.544000] genirq: Flags mismatch irq 96. 00000020 (ptm_mailbox_isr) vs. 00000020 (atm_mailbox_isr)
[ 12.548000] /home/taxodium/trunk/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:970:ifx_ptm_init: IRQ may be occupied by other driver, please reconfig to disable it.
[ 12.612000] ifxmips_ptm: PTM init failed
[ 12.628000] usbcore: registered new interface driver rtl8192cu
[ 12.640000] genirq: Flags mismatch irq 96. 00000020 (ptm_mailbox_isr) vs. 00000020 (atm_mailbox_isr)
[ 12.648000] /home/taxodium/trunk/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:970:ifx_ptm_init: IRQ may be occupied by other driver, please reconfig to disable it.
[ 12.692000] ifxmips_ptm: PTM init failed
[ 18.540000] device eth0 entered promiscuous mode
[ 75.048000] eth0: port 4 got link
[ 75.048000] br-lan: port 1(eth0) entered forwarding state
[ 75.052000] br-lan: port 1(eth0) entered forwarding state
[ 77.056000] br-lan: port 1(eth0) entered forwarding state
root@OpenWrt:~#