bueno por fin conseguido ahora si

solo decir grs por insistir tenias toda la razon gmtii
ahora la imagen no se ejecuta por que

[quoteU-Boot 2013.10-openwrt5-00014-g0b78b5c-dirty (Mar 11 2014 - 22:56:27) arv7519rw
Board: Lantiq ARV7519RW VRX200 Family Board
SoC: Lantiq VRX288 v1.1
CPU: 500 MHz
IO: 250 MHz
BUS: 250 MHz
BOOT: NOR
DRAM: 128 MiB
Flash: 32 MiB
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
arv7519rw # setenv write-openwrt 'tftpboot openwrt-lantiq-xrx200-ARV7519RWV1X-squashfs.image && protect off 0xB0080000 +$filesize && erase 0xB0080000 +$filesize && cp.b $fileaddr 0xB0080000 $filesize'
arv7519rw # setenv ker«±}…‘‘É0xB0080000
syntax error
arv7519rw # saveenv
Saving Environment to Flash...
. done
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... 10....9....8....7....6....5....4....3....2....1....10....9....8....7....6....5....4....3....2....1....done
. done
Protected 1 sectors
arv7519rw # setenv write-openwrt 'tftpboot openwrt-lantiq-xrx200-ARV7519RWV1X-squashfs.image && protect off 0xB0080000 +$filesize && erase 0xB0080000 +$filesize && cp.b $fileaddr 0xB0080000 $filesize'
arv7519rw # setenv kernel_addr 0xB0080000
arv7519rw # saveenv
Saving Environment to Flash...
. done
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... 10....9....8....7....6....5....4....3....2....1....10....9....8....7....6....5....4....3....2....1....done
. done
Protected 1 sectors
arv7519rw # run write-openwrt
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 1, speed 100, duplex 1
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-ARV7519RWV1X-squashfs.image'.
Load address: 0xb0080000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##
830.1 KiB/s
done
Bytes transferred = 3670020 (380004 hex)
............................. done
Un-Protected 29 sectors
............................. done
Erased 29 sectors
Copy to Flash... 10....9....8....7....6....5....4....3....2....1....done
arv7519rw # resetÿ
ROM VER: 1.0.5
CFG 01
U-Boot 2013.10-openwrt5-00014-g0b78b5c-dirty (Mar 11 2014 - 22:56:27) arv7519rw
Board: Lantiq ARV7519RW VRX200 Family Board
SoC: Lantiq VRX288 v1.1
CPU: 500 MHz
IO: 250 MHz
BUS: 250 MHz
BOOT: NOR
DRAM: 128 MiB
Flash: 32 MiB
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
arv7519rw #][/quote]
he seguido la guia para crear la macro tal como esta y tambien con la modificacion del segundo comando este :
setenv loadaddr 0xb0080000
pero nada tam`poco se ejecuta, seguire mirando haber vuelvo a leer todo grs