« anterior próximo »
Páginas: 1 ... 84 85 86 87 88 89 90 [91] 92 93 94 95 96 97 98 ... 156   Ir Abajo

Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a  (Leído 2094773 veces)

0 Usuarios y 8 Visitantes están viendo este tema.

tiagorl

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1800 en: 24-11-2013, 11:16 (Domingo) »
Buenos días;

He leido por ahi que podemos hacer multiwan, es decir unir dos redes conectadas a nuestro reouter. Por ejemplo una conexion wifi y otra lan unidas. Con unas reglas puedes usar una para unas conexiones y otra para otras. La pregunta es la siguiente:
- Se puede hacer bonding entre ambas para poder unir los anchos de banda y que los gestione el openwrt? De tal manera que si la interface wifi tiene una conexion de 10mb de internet y la vlan otra conexión de 10mb poder descargar a 20 mb.

Saludos


En línea

Pteridium

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1801 en: 24-11-2013, 11:29 (Domingo) »
En principio multiwan sí se puede hacer con openwrt y seguramente bonding también; lo complicado será ponerlo a andar, creo.
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1802 en: 24-11-2013, 11:51 (Domingo) »
Cita de: tiagorl en 24-11-2013, 11:16 (Domingo)
Buenos días;

He leido por ahi que podemos hacer multiwan, es decir unir dos redes conectadas a nuestro reouter. Por ejemplo una conexion wifi y otra lan unidas. Con unas reglas puedes usar una para unas conexiones y otra para otras. La pregunta es la siguiente:
- Se puede hacer bonding entre ambas para poder unir los anchos de banda y que los gestione el openwrt? De tal manera que si la interface wifi tiene una conexion de 10mb de internet y la vlan otra conexión de 10mb poder descargar a 20 mb.

Saludos

Mírate este hilo: Multiwan con HG556a (VLANs)
En línea

yone

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1803 en: 25-11-2013, 10:31 (Lunes) »
Hola a todos, soy nuevo y la verdad es que muchas cosas me suenan un poco a chino, solo os pido un poco de info y que no me mateis. He buscado pero no me ha quedado claro.

Tengo un router Huawey HG556a (concretamente HG56BZRB Ver.A) y me gustaria instalarle el OpenWrt y conectarle mi disco duro externo para dejarlo descargando. La cosa es que no me queda claro que version de OpenWRT deberia usar, si este firmware se adapta a lo que busco y sobre todo si podre seguir usando el router con total normalidad(Tanto por el wifi como por el telefono fijo).

Lo dicho, espero no molestar y que alguno me pueda echar un cable. Un saludo  :D
En línea

Chumpy

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1804 en: 25-11-2013, 11:11 (Lunes) »
Cita de: yone en 25-11-2013, 10:31 (Lunes)
Hola a todos, soy nuevo y la verdad es que muchas cosas me suenan un poco a chino, solo os pido un poco de info y que no me mateis. He buscado pero no me ha quedado claro.

Tengo un router Huawey HG556a (concretamente HG56BZRB Ver.A) y me gustaria instalarle el OpenWrt y conectarle mi disco duro externo para dejarlo descargando. La cosa es que no me queda claro que version de OpenWRT deberia usar, si este firmware se adapta a lo que busco y sobre todo si podre seguir usando el router con total normalidad(Tanto por el wifi como por el telefono fijo).

Lo dicho, espero no molestar y que alguno me pueda echar un cable. Un saludo  :D

-OpenWRT hace todo lo que pides.
-Necesitarás una versión que incluya los paquetes que puedas necesitar (o te permita instalarlos), en función de lo que quieras hacer necesitarás un cliente torrent, soporte para ext o ntfs...
-Con OpenWRT no podras utilizarlo como router ADSL, necesitarás conectarlo a otro router que reciba la conexión a internet, la configuración del telefono fijo podría ser compleja aunque lo contectaras a otro. Es decir, necesitas otro router que reciba internet, o mantener el que tienes e instalar OpenWRT en un router diferente.
En línea

venturi

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1805 en: 25-11-2013, 11:52 (Lunes) »
Cita de: jar229 en 24-11-2013, 11:51 (Domingo)
Cita de: tiagorl en 24-11-2013, 11:16 (Domingo)
Buenos días;

He leido por ahi que podemos hacer multiwan, es decir unir dos redes conectadas a nuestro reouter. Por ejemplo una conexion wifi y otra lan unidas. Con unas reglas puedes usar una para unas conexiones y otra para otras. La pregunta es la siguiente:
- Se puede hacer bonding entre ambas para poder unir los anchos de banda y que los gestione el openwrt? De tal manera que si la interface wifi tiene una conexion de 10mb de internet y la vlan otra conexión de 10mb poder descargar a 20 mb.

Saludos

Mírate este hilo: Multiwan con HG556a (VLANs)
y no hay ningun manual para hacerlo desde luci ? , no he encontrado ninguno . y es realmente interesante.
En línea

tiagorl

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1806 en: 25-11-2013, 12:41 (Lunes) »
Cita de: jar229 en 24-11-2013, 11:51 (Domingo)
Cita de: tiagorl en 24-11-2013, 11:16 (Domingo)
Buenos días;

He leido por ahi que podemos hacer multiwan, es decir unir dos redes conectadas a nuestro reouter. Por ejemplo una conexion wifi y otra lan unidas. Con unas reglas puedes usar una para unas conexiones y otra para otras. La pregunta es la siguiente:
- Se puede hacer bonding entre ambas para poder unir los anchos de banda y que los gestione el openwrt? De tal manera que si la interface wifi tiene una conexion de 10mb de internet y la vlan otra conexión de 10mb poder descargar a 20 mb.

Saludos

Mírate este hilo: Multiwan con HG556a (VLANs)

Buenas, ya había echado un ojo a ese hilo, de hecho hay en youtube algunos videos que muestran la configuración multiwan por luci. Con esto lo que puedo conseguir es navegar por una linea y descargar torrent por otra; o bien descargar torrent por ambas. Mi meta es conseguir hacer bonding para que ambas interfaces se "unan" como se de una se tratara, pero no hay mucha documentación al respecto. ¿Alguien puede arrojar algo de luz al asunto?

Mas info aqui: http://www.linuxhorizon.ro/bonding.html

Muchas gracias!


« Última modificación: 25-11-2013, 12:49 (Lunes) por tiagorl »
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1807 en: 26-11-2013, 09:10 (Martes) »
No entiendo que sigáis tratando el tema de Multiwan aquí, cuando hay un hilo específico  ???

Seguro que si escribís en el otro hilo, emeryth, os podrá aclarar algunas cosas ...  ^-^
En línea

tiagorl

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1808 en: 26-11-2013, 16:31 (Martes) »
Cierto, continuo en el otro hilo...
En línea

santiacho

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1809 en: 26-11-2013, 19:53 (Martes) »
Cita de: jar229 en 22-11-2013, 08:32 (Viernes)
El driver para las rtl8187 en OpenWrt no soporta el modo AP. Quizás ocurra lo mismo con el rtl8192cu ...  ^-^

Has probado a hacerlo al revés ?.

Me refiero a usar en pincho usb como cliente y el wifi interno del router como AP.

Muy buenas de nuevo, he vuelto a la carga:

Este es mi dmesg, pero configurando la wifi interna como punto de acceso y el controlador usb como cliente:
root@OpenWrt:~# dmesg
[    0.000000] Linux version 3.10.18 (jar@jar-virtual-machine) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38774) ) #1 Tue Nov 12 11:49:36 CET 2013
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: d081.5003
[    0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 33313330, got 4c97d2a9)
[    0.000000] No bcm_tag found!
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556_A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802e0a90, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 61432k/65536k available (2363k kernel code, 4104k reserved, 602k data, 232k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.048000] NET: Registered protocol family 16
[    0.064000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] PCI host bridge to bus 0000:00
[    0.096000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.100000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.104000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.144000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.152000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.156000] TCP: Hash tables configured (established 512 bind 512)
[    0.164000] TCP: reno registered
[    0.168000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] NET: Registered protocol family 1
[    0.184000] PCI: CLS 0 bytes, default 16
[    0.188000] audit: initializing netlink socket (disabled)
[    0.196000] type=2000 audit(0.195:1): initialized
[    0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.208000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.220000] msgmni has been set to 119
[    0.224000] io scheduler noop registered
[    0.228000] io scheduler deadline registered (default)
[    0.236000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.244000] console [ttyS0] enabled, bootconsole disabled
[    0.260000] physmap platform flash device: 02000000 at 1e000000
[    0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.276000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.276000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.284000]   Amd/Fujitsu Extended Query version 1.3.
[    0.288000] number of CFI chips: 1
[    0.292000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[    0.312000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length da0000
[    0.320000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.328000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.336000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.344000] bcm63xxpart: Spare partition is offset 740004 and length 79fffc
[    0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.356000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.364000] 0x000000000000-0x000000020000 : "CFE"
[    0.372000] 0x000000020100-0x000000140000 : "kernel"
[    0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] 0x000000140000-0x000000ee0000 : "rootfs"
[    0.404000] mtd: device 2 (rootfs) set to be root filesystem
[    0.408000] mtd: partition "rootfs_data" created automatically, ofs=0x740000, len=0x7a0000
[    0.416000] 0x000000740000-0x000000ee0000 : "rootfs_data"
[    0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.444000] 0x000000020000-0x000000ee0000 : "linux"
[    0.456000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[    0.476000] libphy: bcm63xx_enet MII bus: probed
[    0.484000] b53_common: found switch: BCM5325, rev 0
[    0.488000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[    0.504000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.520000] TCP: cubic registered
[    0.524000] NET: Registered protocol family 17
[    0.528000] 8021q: 802.1Q VLAN Support v1.8
[    0.544000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.556000] Freeing unused kernel memory: 232K (802f6000 - 80330000)
[    6.420000] usbcore: registered new interface driver usbfs
[    6.424000] usbcore: registered new interface driver hub
[    6.432000] usbcore: registered new device driver usb
[    6.448000] Button Hotplug driver version 0.4.1
[    6.540000] SCSI subsystem initialized
[    6.560000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.572000] ehci-platform: EHCI generic platform driver
[    6.576000] ehci-platform ehci-platform: EHCI Host Controller
[    6.580000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    6.592000] ehci-platform ehci-platform: irq 18, io mem 0xfffe1300
[    6.608000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    6.616000] hub 1-0:1.0: USB hub found
[    6.620000] hub 1-0:1.0: 2 ports detected
[    6.632000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.640000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[    6.644000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    6.656000] ohci-platform ohci-platform: irq 13, io mem 0xfffe1400
[    6.720000] hub 2-0:1.0: USB hub found
[    6.724000] hub 2-0:1.0: 1 port detected
[    6.736000] uhci_hcd: USB Universal Host Controller Interface driver
[    6.756000] usbcore: registered new interface driver usb-storage
[    6.768000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    7.600000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    8.020000] usb 1-2: new high-speed USB device number 3 using ehci-platform
[    8.172000] hub 1-2:1.0: USB hub found
[    8.176000] hub 1-2:1.0: 4 ports detected
[    9.028000] eth0: link UP - 100/full - flow control off
[   11.836000] jffs2: notice: (258) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   11.908000] jffs2: notice: (255) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   12.120000] eth0: link DOWN
[   15.436000] NET: Registered protocol family 10
[   15.528000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[   15.552000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.600000] fuse init (API version 7.22)
[   15.616000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[   15.624000] Backport generated by backports.git backports-20130617-4-ge3220f5
[   15.644000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.708000] usbcore: registered new interface driver ums-alauda
[   15.720000] usbcore: registered new interface driver ums-cypress
[   15.732000] usbcore: registered new interface driver ums-datafab
[   15.744000] usbcore: registered new interface driver ums-freecom
[   15.756000] usbcore: registered new interface driver ums-isd200
[   15.768000] usbcore: registered new interface driver ums-jumpshot
[   15.776000] usbcore: registered new interface driver ums-karma
[   15.792000] usbcore: registered new interface driver ums-sddr09
[   15.804000] usbcore: registered new interface driver ums-sddr55
[   15.816000] usbcore: registered new interface driver ums-usbat
[   15.828000] usbcore: registered new interface driver usblp
[   15.876000] xt_time: kernel timezone is -0000
[   16.016000] cfg80211: Calling CRDA to update world regulatory domain
[   16.028000] cfg80211: World regulatory domain updated:
[   16.032000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.040000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.048000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   16.056000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   16.064000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.072000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.128000] PPP generic driver version 2.4.2
[   16.144000] NET: Registered protocol family 24
[   16.208000] usbcore: registered new interface driver rt73usb
[   16.232000] usbcore: registered new interface driver rtl8187
[   16.272000] usbcore: registered new interface driver zd1211rw
[   16.368000] usbcore: registered new interface driver carl9170
[   16.396000] usbcore: registered new interface driver rt2500usb
[   16.428000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.436000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.436000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00.eeprom'.
[   16.448000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   16.456000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   16.464000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.496000] usbcore: registered new interface driver rt2800usb
[   16.568000] usbcore: registered new interface driver ath9k_htc
[   16.620000] rtl8192cu: Chip version 0x11
[   17.052000] rtl8192cu: MAC address: 64:66:b3:0a:22:3c
[   17.056000] rtl8192cu: Board Type 0
[   17.060000] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[   17.068000] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
[   17.212000] usbcore: registered new interface driver rtl8192cu
[   17.248000] ieee80211 phy1: Selected rate control algorithm 'rtl_rc'
[   17.284000] rtlwifi: wireless switch is on
[   21.792000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.520000] eth0: link UP - 100/full - flow control off
[   23.528000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.228000] device eth0.1 entered promiscuous mode
[   25.232000] device eth0 entered promiscuous mode
[   25.244000] br-lan: port 1(eth0.1) entered forwarding state
[   25.248000] br-lan: port 1(eth0.1) entered forwarding state
[   26.208000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   26.800000] eth0: link UP - 100/full - flow control off
[   27.252000] br-lan: port 1(eth0.1) entered forwarding state
[   32.920000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   33.060000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[   33.192000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   33.208000] device wlan0 entered promiscuous mode
[   33.328000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   33.840000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   33.848000] br-lan: port 2(wlan0) entered forwarding state
[   33.856000] br-lan: port 2(wlan0) entered forwarding state
[   35.860000] br-lan: port 2(wlan0) entered forwarding state
[   38.672000] cfg80211: Calling CRDA for country: ES
[   38.708000] cfg80211: Regulatory domain changed to country: ES
[   38.712000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   38.720000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   38.728000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   38.736000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   38.744000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   40.420000] rtl8192cu: MAC auto ON okay!
[   40.524000] rtl8192cu: Tx queue select: 0x05
[   41.184000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   43.644000] wlan1: authenticate with c0:ac:54:03:0b:20
[   43.728000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   43.940000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   44.148000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   44.356000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   45.356000] wlan1: authenticate with c0:ac:54:03:0b:20
[   45.400000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   45.608000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   45.816000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   46.024000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   47.328000] wlan1: authenticate with c0:ac:54:03:0b:20
[   47.372000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   47.584000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   47.792000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   48.000000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   49.796000] wlan1: authenticate with c0:ac:54:03:0b:20
[   49.844000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   50.056000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   50.264000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   50.472000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   61.544000] wlan1: authenticate with c0:ac:54:03:0b:20
[   61.588000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   61.796000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   62.004000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   62.212000] wlan1: authentication with c0:ac:54:03:0b:20 timed out

Y este es el dmesg cambiando de puerto USB por el trasero en lugar de por del USB de la parte superior:
root@OpenWrt:~# dmesg
[    0.000000] Linux version 3.10.18 (jar@jar-virtual-machine) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38774) ) #1 Tue Nov 12 11:49:36 CET 2013
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: d081.5003
[    0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 33313330, got 4c97d2a9)
[    0.000000] No bcm_tag found!
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556_A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802e0a90, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 61432k/65536k available (2363k kernel code, 4104k reserved, 602k data, 232k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.048000] NET: Registered protocol family 16
[    0.064000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] PCI host bridge to bus 0000:00
[    0.096000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.100000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.104000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.144000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.152000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.156000] TCP: Hash tables configured (established 512 bind 512)
[    0.164000] TCP: reno registered
[    0.168000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] NET: Registered protocol family 1
[    0.184000] PCI: CLS 0 bytes, default 16
[    0.188000] audit: initializing netlink socket (disabled)
[    0.196000] type=2000 audit(0.195:1): initialized
[    0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.208000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.220000] msgmni has been set to 119
[    0.224000] io scheduler noop registered
[    0.228000] io scheduler deadline registered (default)
[    0.236000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.244000] console [ttyS0] enabled, bootconsole disabled
[    0.260000] physmap platform flash device: 02000000 at 1e000000
[    0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.276000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.276000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.284000]   Amd/Fujitsu Extended Query version 1.3.
[    0.288000] number of CFI chips: 1
[    0.292000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[    0.312000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length da0000
[    0.320000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.328000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.336000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.344000] bcm63xxpart: Spare partition is offset 740004 and length 79fffc
[    0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.356000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.364000] 0x000000000000-0x000000020000 : "CFE"
[    0.372000] 0x000000020100-0x000000140000 : "kernel"
[    0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] 0x000000140000-0x000000ee0000 : "rootfs"
[    0.404000] mtd: device 2 (rootfs) set to be root filesystem
[    0.408000] mtd: partition "rootfs_data" created automatically, ofs=0x740000, len=0x7a0000
[    0.416000] 0x000000740000-0x000000ee0000 : "rootfs_data"
[    0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.444000] 0x000000020000-0x000000ee0000 : "linux"
[    0.456000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[    0.476000] libphy: bcm63xx_enet MII bus: probed
[    0.484000] b53_common: found switch: BCM5325, rev 0
[    0.488000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[    0.504000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.520000] TCP: cubic registered
[    0.524000] NET: Registered protocol family 17
[    0.528000] 8021q: 802.1Q VLAN Support v1.8
[    0.544000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.556000] Freeing unused kernel memory: 232K (802f6000 - 80330000)
[    6.420000] usbcore: registered new interface driver usbfs
[    6.424000] usbcore: registered new interface driver hub
[    6.432000] usbcore: registered new device driver usb
[    6.448000] Button Hotplug driver version 0.4.1
[    6.540000] SCSI subsystem initialized
[    6.560000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.572000] ehci-platform: EHCI generic platform driver
[    6.576000] ehci-platform ehci-platform: EHCI Host Controller
[    6.580000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    6.592000] ehci-platform ehci-platform: irq 18, io mem 0xfffe1300
[    6.608000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    6.616000] hub 1-0:1.0: USB hub found
[    6.620000] hub 1-0:1.0: 2 ports detected
[    6.632000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.640000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[    6.644000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    6.656000] ohci-platform ohci-platform: irq 13, io mem 0xfffe1400
[    6.720000] hub 2-0:1.0: USB hub found
[    6.724000] hub 2-0:1.0: 1 port detected
[    6.736000] uhci_hcd: USB Universal Host Controller Interface driver
[    6.756000] usbcore: registered new interface driver usb-storage
[    6.768000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    7.456000] usb 1-2: new high-speed USB device number 2 using ehci-platform
[    8.020000] hub 1-2:1.0: USB hub found
[    8.024000] hub 1-2:1.0: 4 ports detected
[    8.304000] usb 1-2.1: new high-speed USB device number 3 using ehci-platform
[    9.608000] eth0: link UP - 100/full - flow control off
[   11.828000] jffs2: notice: (257) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   11.900000] jffs2: notice: (254) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   12.660000] eth0: link DOWN
[   15.436000] NET: Registered protocol family 10
[   15.532000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[   15.552000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.600000] fuse init (API version 7.22)
[   15.620000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[   15.628000] Backport generated by backports.git backports-20130617-4-ge3220f5
[   15.644000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.708000] usbcore: registered new interface driver ums-alauda
[   15.720000] usbcore: registered new interface driver ums-cypress
[   15.732000] usbcore: registered new interface driver ums-datafab
[   15.744000] usbcore: registered new interface driver ums-freecom
[   15.756000] usbcore: registered new interface driver ums-isd200
[   15.768000] usbcore: registered new interface driver ums-jumpshot
[   15.780000] usbcore: registered new interface driver ums-karma
[   15.792000] usbcore: registered new interface driver ums-sddr09
[   15.804000] usbcore: registered new interface driver ums-sddr55
[   15.816000] usbcore: registered new interface driver ums-usbat
[   15.828000] usbcore: registered new interface driver usblp
[   15.876000] xt_time: kernel timezone is -0000
[   15.956000] cfg80211: Calling CRDA to update world regulatory domain
[   15.972000] cfg80211: World regulatory domain updated:
[   15.976000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   15.984000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.992000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   16.000000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   16.008000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.016000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.140000] PPP generic driver version 2.4.2
[   16.156000] NET: Registered protocol family 24
[   16.212000] usbcore: registered new interface driver rt73usb
[   16.232000] usbcore: registered new interface driver rtl8187
[   16.268000] usbcore: registered new interface driver zd1211rw
[   16.368000] usbcore: registered new interface driver carl9170
[   16.396000] usbcore: registered new interface driver rt2500usb
[   16.428000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.436000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.436000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00.eeprom'.
[   16.448000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   16.456000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   16.464000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.492000] usbcore: registered new interface driver rt2800usb
[   16.552000] usbcore: registered new interface driver ath9k_htc
[   16.600000] rtl8192cu: Chip version 0x11
[   17.056000] rtl8192cu: MAC address: 64:66:b3:0a:22:3c
[   17.060000] rtl8192cu: Board Type 0
[   17.064000] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[   17.072000] usbcore: registered new interface driver rtl8192cu
[   21.660000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.280000] eth0: link UP - 100/full - flow control off
[   23.292000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   24.848000] device eth0.1 entered promiscuous mode
[   24.852000] device eth0 entered promiscuous mode
[   24.868000] br-lan: port 1(eth0.1) entered forwarding state
[   24.872000] br-lan: port 1(eth0.1) entered forwarding state
[   25.820000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   26.444000] eth0: link UP - 100/full - flow control off
[   26.876000] br-lan: port 1(eth0.1) entered forwarding state
[   32.448000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   32.608000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[   32.740000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   32.752000] device wlan0 entered promiscuous mode
[   32.872000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   33.384000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   33.392000] br-lan: port 2(wlan0) entered forwarding state
[   33.400000] br-lan: port 2(wlan0) entered forwarding state
[   35.404000] br-lan: port 2(wlan0) entered forwarding state

La verdad, no se que mas probar... estoy en vuestras manos...  :'(

Muchas gracias de nuevo por la ayuda tan desinteresada que prestáis.

Saludos.
« Última modificación: 26-11-2013, 20:29 (Martes) por santiacho »
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1810 en: 27-11-2013, 09:58 (Miércoles) »
Aquí se ven continuos intentos de conexión/asociación

Código: [Seleccionar]
[   43.644000] wlan1: authenticate with c0:ac:54:03:0b:20
[   43.728000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   43.940000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   44.148000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   44.356000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   45.356000] wlan1: authenticate with c0:ac:54:03:0b:20
[   45.400000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   45.608000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   45.816000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   46.024000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   47.328000] wlan1: authenticate with c0:ac:54:03:0b:20
[   47.372000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   47.584000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   47.792000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   48.000000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   49.796000] wlan1: authenticate with c0:ac:54:03:0b:20
[   49.844000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   50.056000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   50.264000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   50.472000] wlan1: authentication with c0:ac:54:03:0b:20 timed out
[   61.544000] wlan1: authenticate with c0:ac:54:03:0b:20
[   61.588000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 1/3)
[   61.796000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 2/3)
[   62.004000] wlan1: direct probe to c0:ac:54:03:0b:20 (try 3/3)
[   62.212000] wlan1: authentication with c0:ac:54:03:0b:20 timed out

Tienes toda la pinta de que este adaptador no anda nada fino en OpenWrt ...  ^-^

No tienes ningún otro pincho wifi para probar ?
En línea

santiacho

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1811 en: 27-11-2013, 10:31 (Miércoles) »
Hola,

muchas gracias por tu respuesta.

Al final, estaba tan desesperado que saqué un pincho wifi que tenía en el cajón bastante antigüete... red b/g. Lo configuré ayer y funcionó todo a la primera  ;D, pero la velocidad de descarga ha bajado bastante. Hice un test de velocidad conectado al OpenWRT y otra conectado al router de Orange directamente y la verdad que cambia radicalmente de 3MB conectado a OpenWRT a 10MB conectado al router de Orange. (tengo  20MB contratados). Alguna idea de como lograr recuperar la velocidad o que se aproxime bastante?

Gracias.
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1812 en: 28-11-2013, 09:13 (Jueves) »
Qué chipset lleva el adaptador que has usado ?

Lo usas como AP o como cliente ?

Has probado al revés ?
En línea

santiacho

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1813 en: 28-11-2013, 12:20 (Jueves) »
El chipset ahora mismo no lo sé, pero en llegar a casa lo miro.

Lo tengo configurado como cliente, usando el wifi interno como AP. Si que lo probé al revés, pero parecía como que se quedaba sin internet el router y tenía que reiniciarlo. Con la versión que tengo ahora mismo (r38774) y de la forma que lo tengo ahora, parece que no se desconecta, algo es algo, pero si que he notado una bajada de velocidad en la navegación.

Me recomiendas otra versión de openWRT o con la que tengo me debe funcionar...

Lo dicho, en llegar a casa pongo el dmesg e intento sacar el chipset...

Gracias.
En línea

Altair64

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1814 en: 28-11-2013, 13:14 (Jueves) »
Buenas! me he agenciado uno de estos routers. Ahora mismo estaba usando como router "principal" en casa un AR5387un y veo que mas o menos en cuando a características técnicas son parecidos, pero este HG556 veo que tiene una CPU de doble nucleo (eso dice el wiki de openwrt). ¿Ese segundo núcleo sería usable, sería "positivo", o estaría "bloqueado"? Porque en nosecual router (uno de Astoria de Yacom o algo asi que hay en el foro) pone que tambien tiene 2 nucleos pero uno solo es para las llamadas de voz o algo asi...

Por lo demas veo que tiene 3 USBs en comparacion con solo 1 usb que tiene el que tengo de jazztel (aunque en este no se si el que tiene por arriba funcionaria, creo haber leido por aqui que no va, pero con tener 2 llegan hehe). Pero me tira para atrás el diseño! es horrible!  ;D  aparte me queda mejor el de jazztel por la forma y donde lo tengo colocado.

S2!
En línea

tool

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1815 en: 28-11-2013, 17:24 (Jueves) »
Dejo por aquí si alguien se anima a compartir para varios lo siguiente:
Compilación Full equip para usar como NAS, para copias, soporte para HFS+ en el kernel etc. Soporte también EXFAT

Utilidades como el que hay ahora con reaver airmon y soporte para wifis USB.

A ver si para la semana pruebo a configurar uno para gente que tiene internet de Yoigo.
Con los modem USB de yoigo + HG556a para dar internet.

En línea

santiacho

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1816 en: 28-11-2013, 22:33 (Jueves) »
Cita de: santiacho en 28-11-2013, 12:20 (Jueves)
El chipset ahora mismo no lo sé, pero en llegar a casa lo miro.

Lo tengo configurado como cliente, usando el wifi interno como AP. Si que lo probé al revés, pero parecía como que se quedaba sin internet el router y tenía que reiniciarlo. Con la versión que tengo ahora mismo (r38774) y de la forma que lo tengo ahora, parece que no se desconecta, algo es algo, pero si que he notado una bajada de velocidad en la navegación.

Me recomiendas otra versión de openWRT o con la que tengo me debe funcionar...

Lo dicho, en llegar a casa pongo el dmesg e intento sacar el chipset...

Gracias.

Buenas noches, frías pero buenas!  :D

Bueno, este es mi dmesg:
root@OpenWrt:~# dmesg
[    0.000000] Linux version 3.10.18 (jar@jar-virtual-machine) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38774) ) #1 Tue Nov 12 11:49:36 CET 2013
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: d081.5003
[    0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 33313330, got 4c97d2a9)
[    0.000000] No bcm_tag found!
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556_A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802e0a90, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 61432k/65536k available (2363k kernel code, 4104k reserved, 602k data, 232k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.048000] NET: Registered protocol family 16
[    0.064000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] PCI host bridge to bus 0000:00
[    0.096000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.100000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.104000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.108000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[    0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.120000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.144000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.152000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.156000] TCP: Hash tables configured (established 512 bind 512)
[    0.164000] TCP: reno registered
[    0.168000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.172000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] NET: Registered protocol family 1
[    0.184000] PCI: CLS 0 bytes, default 16
[    0.188000] audit: initializing netlink socket (disabled)
[    0.196000] type=2000 audit(0.195:1): initialized
[    0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.208000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.220000] msgmni has been set to 119
[    0.224000] io scheduler noop registered
[    0.228000] io scheduler deadline registered (default)
[    0.236000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.244000] console [ttyS0] enabled, bootconsole disabled
[    0.260000] physmap platform flash device: 02000000 at 1e000000
[    0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.276000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.276000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.284000]   Amd/Fujitsu Extended Query version 1.3.
[    0.288000] number of CFI chips: 1
[    0.292000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[    0.312000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length da0000
[    0.320000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[    0.328000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.336000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[    0.344000] bcm63xxpart: Spare partition is offset 740004 and length 79fffc
[    0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.356000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.364000] 0x000000000000-0x000000020000 : "CFE"
[    0.372000] 0x000000020100-0x000000140000 : "kernel"
[    0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] 0x000000140000-0x000000ee0000 : "rootfs"
[    0.404000] mtd: device 2 (rootfs) set to be root filesystem
[    0.408000] mtd: partition "rootfs_data" created automatically, ofs=0x740000, len=0x7a0000
[    0.416000] 0x000000740000-0x000000ee0000 : "rootfs_data"
[    0.428000] 0x000000ee0000-0x000000f00000 : "cal_data"
[    0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.444000] 0x000000020000-0x000000ee0000 : "linux"
[    0.456000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[    0.476000] libphy: bcm63xx_enet MII bus: probed
[    0.484000] b53_common: found switch: BCM5325, rev 0
[    0.488000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[    0.504000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.520000] TCP: cubic registered
[    0.524000] NET: Registered protocol family 17
[    0.528000] 8021q: 802.1Q VLAN Support v1.8
[    0.544000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.556000] Freeing unused kernel memory: 232K (802f6000 - 80330000)
[    6.416000] usbcore: registered new interface driver usbfs
[    6.424000] usbcore: registered new interface driver hub
[    6.432000] usbcore: registered new device driver usb
[    6.448000] Button Hotplug driver version 0.4.1
[    6.540000] SCSI subsystem initialized
[    6.560000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.568000] ehci-platform: EHCI generic platform driver
[    6.576000] ehci-platform ehci-platform: EHCI Host Controller
[    6.580000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    6.588000] ehci-platform ehci-platform: irq 18, io mem 0xfffe1300
[    6.608000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    6.616000] hub 1-0:1.0: USB hub found
[    6.620000] hub 1-0:1.0: 2 ports detected
[    6.632000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.640000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[    6.644000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    6.656000] ohci-platform ohci-platform: irq 13, io mem 0xfffe1400
[    6.720000] hub 2-0:1.0: USB hub found
[    6.724000] hub 2-0:1.0: 1 port detected
[    6.736000] uhci_hcd: USB Universal Host Controller Interface driver
[    6.756000] usbcore: registered new interface driver usb-storage
[    6.768000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    7.600000] usb 1-2: new high-speed USB device number 2 using ehci-platform
[    7.908000] hub 1-2:1.0: USB hub found
[    7.912000] hub 1-2:1.0: 4 ports detected
[    8.216000] usb 1-2.1: new high-speed USB device number 3 using ehci-platform
[    9.608000] eth0: link UP - 100/full - flow control off
[   11.836000] jffs2: notice: (257) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   11.908000] jffs2: notice: (254) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   12.668000] eth0: link DOWN
[   15.440000] NET: Registered protocol family 10
[   15.532000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[   15.552000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.600000] fuse init (API version 7.22)
[   15.620000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[   15.628000] Backport generated by backports.git backports-20130617-4-ge3220f5
[   15.644000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.708000] usbcore: registered new interface driver ums-alauda
[   15.720000] usbcore: registered new interface driver ums-cypress
[   15.732000] usbcore: registered new interface driver ums-datafab
[   15.744000] usbcore: registered new interface driver ums-freecom
[   15.756000] usbcore: registered new interface driver ums-isd200
[   15.768000] usbcore: registered new interface driver ums-jumpshot
[   15.780000] usbcore: registered new interface driver ums-karma
[   15.792000] usbcore: registered new interface driver ums-sddr09
[   15.804000] usbcore: registered new interface driver ums-sddr55
[   15.816000] usbcore: registered new interface driver ums-usbat
[   15.832000] usbcore: registered new interface driver usblp
[   15.876000] xt_time: kernel timezone is -0000
[   15.952000] cfg80211: Calling CRDA to update world regulatory domain
[   15.972000] cfg80211: World regulatory domain updated:
[   15.976000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   15.984000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.992000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   16.000000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   16.008000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.016000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.124000] PPP generic driver version 2.4.2
[   16.136000] NET: Registered protocol family 24
[   16.188000] usbcore: registered new interface driver rt73usb
[   16.220000] usbcore: registered new interface driver rtl8187
[   16.344000] usb 1-2.1: reset high-speed USB device number 3 using ehci-platform
[   16.448000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.456000] zd1211rw 1-2.1:1.0: phy0
[   16.460000] usbcore: registered new interface driver zd1211rw
[   16.604000] usbcore: registered new interface driver carl9170
[   16.640000] usbcore: registered new interface driver rt2500usb
[   16.696000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.700000] rt2800pci 0000:00:01.0: setting latency timer to 64
[   16.704000] ieee80211 phy1: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00.eeprom'.
[   16.720000] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   16.728000] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0008 detected
[   16.968000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   17.000000] usbcore: registered new interface driver rt2800usb
[   17.080000] usbcore: registered new interface driver ath9k_htc
[   17.128000] usbcore: registered new interface driver rtl8192cu
[   21.700000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.396000] eth0: link UP - 100/full - flow control off
[   23.408000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   24.844000] device eth0.1 entered promiscuous mode
[   24.848000] device eth0 entered promiscuous mode
[   24.868000] br-lan: port 1(eth0.1) entered forwarding state
[   24.872000] br-lan: port 1(eth0.1) entered forwarding state
[   25.828000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   26.636000] eth0: link UP - 100/full - flow control off
[   26.876000] br-lan: port 1(eth0.1) entered forwarding state
[   33.428000] zd1211rw 1-2.1:1.0: firmware version 4725
[   33.596000] zd1211rw 1-2.1:1.0: zd1211b chip 0ace:1215 v4810 high 00-16-44 AL2230_RF pa0 ---NS
[   33.884000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   33.896000] cfg80211: Calling CRDA for country: US
[   33.924000] cfg80211: Regulatory domain changed to country: US
[   33.928000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   33.936000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   33.944000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   33.952000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.960000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.968000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.976000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   34.124000] device wlan0 entered promiscuous mode
[   34.548000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   34.568000] cfg80211: Calling CRDA to update world regulatory domain
[   34.588000] cfg80211: World regulatory domain updated:
[   34.592000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   34.600000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   34.608000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   34.616000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   34.624000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   34.632000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   36.308000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   36.332000] br-lan: port 2(wlan0) entered forwarding state
[   36.336000] br-lan: port 2(wlan0) entered forwarding state
[   38.340000] br-lan: port 2(wlan0) entered forwarding state
[   44.532000] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   44.748000] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[   44.932000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   49.964000] wlan1: authenticate with c0:ac:54:03:0b:20
[   50.020000] wlan1: send auth to c0:ac:54:03:0b:20 (try 1/3)
[   50.036000] wlan1: authenticated
[   50.060000] wlan1: associate with c0:ac:54:03:0b:20 (try 1/3)
[   50.072000] wlan1: RX AssocResp from c0:ac:54:03:0b:20 (capab=0x431 status=0 aid=6)
[   50.080000] wlan1: associated
[   50.092000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready

Añado esto que acabo de ver:
[ 1227.476000] ieee80211 phy1: rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2
[ 1227.476000] Please file bug report to http://rt2x00.serialmonkey.com

El problema que me encuentro ahora es la velocidad de descarga.
http://puu.sh/5w8id.png

El problema no es del todo grave ya que puedo seguir conectandome al router de Orange directamente... pero si que me gustaría hacerlo en el OpenWRT directamente.  :-\

En fin, a ver si los espartos ven algo raro...

Muchas gracias una vez mas.
« Última modificación: 28-11-2013, 22:47 (Jueves) por santiacho »
En línea

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1817 en: 29-11-2013, 09:27 (Viernes) »
Tiene chipset zydas:

Código: [Seleccionar]
[   16.456000] zd1211rw 1-2.1:1.0: phy0

Para probar si la cosa mejora, puedes probar otras compilaciones.

Cualquiera que incluya el driver kmod-zd1211rw debería valerte.

En el primer post del hilo tienes varias: r38342, r37180, r36114
En línea

santiacho

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1818 en: 29-11-2013, 10:06 (Viernes) »
Perfecto, probaré alguna de estas compilaciones a ver si mejora la cosa.

Muchas gracias jar229!

Saludos.
En línea

Durruti

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #1819 en: 01-12-2013, 19:50 (Domingo) »
¿Existe alguna manera facil de distinguir si este router trae wifi atheros o no? De manera externa sin tener que abrirlo.
Me interesa conseguir uno como repetidor sin necesidad de enchufarle antenas wifi, pero comprarlo a ciegas parece una tombola.
En línea


Páginas: 1 ... 84 85 86 87 88 89 90 [91] 92 93 94 95 96 97 98 ... 156   Ir Arriba
« anterior próximo »
 

Si quieres tener la mejor experiencia posible de navegación y uso de la web activa y acepta nuestras políticas de privacidad y cookies. En caso contrario te recomendamos abandonar la web y buscar la información en otro sitio. Si quieres registrarte en el foro deberás aceptar las políticas de privacidad y las condiciones de uso. Learn more