?>/script>'; } ?> [Desarrollo] OpenWrt en Huawei HG556a Widgets Magazine

Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a  (Leído 2175856 veces)

0 Usuarios y 4 Visitantes están viendo este tema.

eq7mavala

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #880 en: 12-11-2012, 11:42 (Lunes) »
Una pregunta os funcionan todos los led's? Es que a mi con la ultima versión no me funcionan todos, en el que tiene chip atheros funcionan todos menos el del wifi, en el de chip ralink solo el wifi, el del mundo y power.


Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #881 en: 12-11-2012, 11:57 (Lunes) »
Una pregunta os funcionan todos los led's? Es que a mi con la ultima versión no me funcionan todos, en el que tiene chip atheros funcionan todos menos el del wifi, en el de chip ralink solo el wifi, el del mundo y power.
Pues a mi sí me funcionan :$...

De todas formas mira de vez en cuando el hilo, porque cuando me acepten todos los parches de "soporte previo" para el HG556a haré una compilación final para que todo el mundo lo pruebe y comprobemos que funciona todo. Esta compilación era más para probar que el wifi funcionaba en los Ralink.

Saludos!


Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: OpenWRT en Huawei hg556a
« Respuesta #882 en: 12-11-2012, 13:23 (Lunes) »
A mi el del wifi tampoco me funciona. Pero yo estoy con una compilación propia y algo antigua (r33456) ...  ^-^


Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #883 en: 12-11-2012, 14:50 (Lunes) »
A mi el del wifi tampoco me funciona. Pero yo estoy con una compilación propia y algo antigua (r33456) ...  ^-^

En versiones anteriores al último firmware que he publicado es normal que no funcione porque en su día consideré que no era necesario para un firmware que no es "oficial". Sin embargo, no os preocupéis porque me aseguraré de que funcione cuando se integren todos los parches.

Saludos.


venturi

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #884 en: 13-11-2012, 16:49 (Martes) »
hola , podrias añadirle el soporte para tarjetas usb , en concreto kmod_ath9_htc para las wifistation ext , y el wpasupplicant.? ya puestos a compilar , jeje , te lo agredeceria muchisimo  >:D


darkvier

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #885 en: 19-11-2012, 01:46 (Lunes) »
http://212.166.190.34/zonadescargas/Guia_identificacion_versiones.pdf

Al parecer hay tres versiones del router y en vodafone los diferencian por el Numero de serie


fRUTTiFrESH

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #886 en: 19-11-2012, 10:38 (Lunes) »
Hi,

sorry for the language, but my spanish is horrible :)

I´am using the HG556a with the r33456 firmware - how can I install for example the kmod-usb-serial-ftdi package?
I got error messages if I try to install external packages.

Thanks in advance

Saludos


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #887 en: 19-11-2012, 11:38 (Lunes) »
http://212.166.190.34/zonadescargas/Guia_identificacion_versiones.pdf

Al parecer hay tres versiones del router y en vodafone los diferencian por el Numero de serie
¡Muchas gracias por la información!
¿Sabemos de dónde ha salido :P?

Cuando tenga un rato la añado a la wiki.

Hi,

sorry for the language, but my spanish is horrible :)

I´am using the HG556a with the r33456 firmware - how can I install for example the kmod-usb-serial-ftdi package?
I got error messages if I try to install external packages.

Thanks in advance

Saludos
You keep getting those error messages because the hash doesn't match the one in the repositories. Once the router is "officially" supported by Openwrt these errors won't appear again.

To ignore the errors you need to "--force-depends". However, this method ignores the dependencies, so you may have to install them one by one manually.
Código: [Seleccionar]
opkg install --force-depends kmod-usb-serial kmod-usb-serial-ftdi


fRUTTiFrESH

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #888 en: 19-11-2012, 12:02 (Lunes) »
Thanks Noltari!

After Installation the ftdi package won´t start. Is there another package missing?

Thanks in advance

[spoiler=log]
Código: [Seleccionar]
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61800k/65536k available (2279k kernel code, 3736k reserved, 409k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.200000] PCI: CLS 0 bytes, default 16
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length de0000
[    0.360000] bcm63xxpart: Spare partition is offset 5c0004 and length 83fffc
[    0.368000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000e00000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=840000
[    0.432000] 0x0000005c0000-0x000000e00000 : "rootfs_data"
[    0.444000] 0x000000e00000-0x000000fe0000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000e00000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.488000] Registered led device: HW556:red:message
[    0.492000] Registered led device: HW556:red:hspa
[    0.492000] Registered led device: HW556:red:dsl
[    0.492000] Registered led device: HW556:red:power
[    0.492000] Registered led device: HW556:red:all
[    0.496000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.504000] 8021q: 802.1Q VLAN Support v1.8
[    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 200k freed
[    3.476000] eth0: link forced UP - 100/full - flow control off/off
[    3.708000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.772000] There is already a switch registered on the device 'eth0'
[    6.228000] Button Hotplug driver version 0.4.1
[   10.248000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 21 of xref (0 dead, 12 orphan) found.
[   13.924000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.932000] Backport based on wireless-testing.git master-2012-09-07
[   13.936000] compat.git: wireless-testing.git
[   14.004000] cfg80211: Calling CRDA to update world regulatory domain
[   14.008000] cfg80211: World regulatory domain updated:
[   14.016000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   14.024000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.032000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.040000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.048000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.056000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.656000] SCSI subsystem initialized
[   14.748000] There is already a switch registered on the device 'eth0'
[   15.012000] usbcore: registered new interface driver usbfs
[   15.016000] usbcore: registered new interface driver hub
[   15.024000] usbcore: registered new device driver usb
[   16.324000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.340000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   16.348000] ath: phy0: random mac address will be used: 4a:e5:14:fc:bb:9d
[   16.356000] ath: EEPROM regdomain: 0x0
[   16.356000] ath: EEPROM indicates default country code should be used
[   16.356000] ath: doing EEPROM country->regdmn map search
[   16.356000] ath: country maps to regdmn code: 0x3a
[   16.356000] ath: Country alpha2 being used: US
[   16.356000] ath: Regpair used: 0x3a
[   16.368000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.372000] Registered led device: ath9k-phy0
[   16.372000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[   16.380000] cfg80211: Calling CRDA for country: US
[   16.384000] cfg80211: Regulatory domain changed to country: US
[   16.388000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.396000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   16.404000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   16.412000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.420000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.428000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.436000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   17.776000] PPP generic driver version 2.4.2
[   18.356000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.740000] NET: Registered protocol family 24
[   18.952000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.064000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.068000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.104000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.120000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.128000] hub 1-0:1.0: USB hub found
[   19.132000] hub 1-0:1.0: 2 ports detected
[   19.328000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[   19.656000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   20.240000] hub 1-1:1.0: USB hub found
[   20.252000] hub 1-1:1.0: 2 ports detected
[   20.376000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.380000] usb 1-2: new high-speed USB device number 3 using bcm63xx_ehci
[   20.484000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.488000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.496000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.564000] hub 2-0:1.0: USB hub found
[   20.568000] hub 2-0:1.0: 2 ports detected
[   20.744000] uhci_hcd: USB Universal Host Controller Interface driver
[   20.936000] usbcore: registered new interface driver usblp
[   20.960000] usb 1-1.1: new full-speed USB device number 4 using bcm63xx_ehci
[   21.016000] usbcore: registered new interface driver usbserial
[   21.024000] USB Serial support registered for generic
[   21.120000] usbcore: registered new interface driver usbserial_generic
[   21.124000] usbserial: USB Serial Driver core
[   21.176000] Initializing USB Mass Storage driver...
[   21.184000] usb 1-2: USB disconnect, device number 3
[   21.192000] scsi0 : usb-storage 1-2:1.0
[   21.200000] scsi1 : usb-storage 1-2:1.1
[   21.204000] usbcore: registered new interface driver usb-storage
[   21.208000] USB Mass Storage support registered.
[   21.428000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   21.512000] USB Serial support registered for FTDI USB Serial Device
[   21.520000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 83351918, ra == 8335189c
[   21.528000] Oops[#1]:
[   21.528000] Cpu 0
[   21.528000] $ 0   : 00000000 00000065 00000000 83350000
[   21.528000] $ 4   : 00000001 833738e0 00006001 00006001
[   21.528000] $ 8   : 00000008 80131d08 00000008 00000000
[   21.528000] $12   : 00000000 00000000 810255a0 74207265
[   21.528000] $16   : 8335583c 83376a58 83310c68 83376b64
[   21.528000] $20   : 83b53480 f7ffffff 83310c00 8024e244
[   21.528000] $24   : 00000018 00000000                  
[   21.528000] $28   : 8331e000 8331fc18 8024e264 8335189c
[   21.528000] Hi    : 00000006
[   21.528000] Lo    : 0000000b
[   21.528000] epc   : 83351918 0x83351918
[   21.528000]     Tainted: G           O
[   21.528000] ra    : 8335189c 0x8335189c
[   21.528000] Status: 10008403    KERNEL EXL IE
[   21.528000] Cause : 00800008
[   21.528000] BadVA : 00000000
[   21.528000] PrId  : 0002a010 (Broadcom BMIPS4350)
[   21.528000] Modules linked in: ftdi_sio(+) gpio_keys_polled usb_storage usbserial usblp uhci_hcd ohci_hcd nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat pppoe xt_conntrack xt_CT xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack ehci_hcd sd_mod pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc vfat fat ext4 jbd2 mbcache rt2800pci(O) ath9k(O) rt2800lib(O) ath9k_common(O) ath9k_hw(O) rt2x00pci(O) ath(O) rt2x00lib(O) nls_utf8 nls_iso8859_15 nls_cp852 nls_cp850 nls_cp437 mac80211(O) usbcore usb_common scsi_mod nls_base crc16 crc_itu_t crc_ccitt eeprom_93cx6 cfg80211(O) compat(O) arc4 aes_generic crypto_algapi button_hotplug(O) input_polldev input_core switch_robo(O) switch_core(O)
[   21.528000] Process insmod (pid: 493, threadinfo=8331e000, task=83b4d178, tls=77928440)
[   21.528000] Stack : 00000000 8331fc90 8334e7c0 00000000 8333d6d0 8331fce0 832adf80 00000001
[   21.528000]         802a0000 800ea5cc 8333d6d0 8334e7c0 ffffffef 8331fce0 832adf80 00000001
[   21.528000]         802a0000 800eb3ac 8334e7c0 8331d100 8331d100 00000008 fffffff5 80300000
[   21.528000]         0000a1ff 800ead68 8334e540 8334e7c0 8334e7c0 8334e540 8331fce0 800eb420
[   21.528000]         000041ed 8026c474 fffffffe 8334e7c0 00000000 8334e540 8333d6d0 832adf80
[   21.528000]         ...
[   21.528000] Call Trace:[<800ea5cc>] 0x800ea5cc
[   21.528000] [<800eb3ac>] 0x800eb3ac
[   21.528000] [<800ead68>] 0x800ead68
[   21.528000] [<800eb420>] 0x800eb420
[   21.528000] [<800ebeec>] 0x800ebeec
[   21.528000] [<8304bdbc>] 0x8304bdbc
[   21.528000] [<8016dacc>] 0x8016dacc
[   21.528000] [<8016dd58>] 0x8016dd58
[   21.528000] [<8304bc78>] 0x8304bc78
[   21.528000] [<8016de78>] 0x8016de78
[   21.528000] [<8016c2ac>] 0x8016c2ac
[   21.528000] [<8016de0c>] 0x8016de0c
[   21.528000] [<8016c5c4>] 0x8016c5c4
[   21.528000] [<801293c4>] 0x801293c4
[   21.528000] [<8016d55c>] 0x8016d55c
[   21.528000] [<8016d69c>] 0x8016d69c
[   21.528000] [<8016e23c>] 0x8016e23c
[   21.528000] [<8304b488>] 0x8304b488
[   21.528000] [<83350cb8>] 0x83350cb8
[   21.528000] [<83370000>] 0x83370000
[   21.528000] [<833770c4>] 0x833770c4
[   21.528000] [<83377000>] 0x83377000
[   21.528000] [<80010900>] 0x80010900
[   21.528000] [<80094e28>] 0x80094e28
[   21.528000] [<8004dba4>] 0x8004dba4
[   21.528000] [<80062164>] 0x80062164
[   21.528000] [<8001a750>] 0x8001a750
[   21.528000] [<80131cf8>] 0x80131cf8
[   21.528000]
[   21.528000]
[   21.528000] Code: 108303bf  3c038335  8c420140 <8c430000> 24630001  ac430000  3c038335  24645830  0c091862
[   21.856000] ---[ end trace 61fc588ad063834b ]---
[   21.904000] fuse init (API version 7.18)
[   26.284000] usb 1-2: new high-speed USB device number 5 using bcm63xx_ehci
[   26.452000] scsi6 : usb-storage 1-2:1.4
[   26.460000] scsi7 : usb-storage 1-2:1.5
[   27.220000] eth0: link forced UP - 100/full - flow control off/off
[   27.248000] device eth0 entered promiscuous mode
[   27.260000] br-lan: port 1(eth0) entered forwarding state
[   27.264000] br-lan: port 1(eth0) entered forwarding state
[   27.456000] scsi 6:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[   27.488000] scsi 7:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[   27.508000] sd 7:0:0:0: [sda] Attached SCSI removable disk
[   29.268000] br-lan: port 1(eth0) entered forwarding state
[   32.356000] device wlan0 entered promiscuous mode
[   34.760000] br-lan: port 2(wlan0) entered forwarding state
[   34.764000] br-lan: port 2(wlan0) entered forwarding state
[   36.768000] br-lan: port 2(wlan0) entered forwarding state
[/spoiler]

« Última modificación: 19-11-2012, 12:24 (Lunes) por jar229 »

Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #889 en: 19-11-2012, 12:34 (Lunes) »
Thanks Noltari!

After Installation the ftdi package won´t start. Is there another package missing?

Thanks in advance

[spoiler=log]
Código: [Seleccionar]
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61800k/65536k available (2279k kernel code, 3736k reserved, 409k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.200000] PCI: CLS 0 bytes, default 16
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length de0000
[    0.360000] bcm63xxpart: Spare partition is offset 5c0004 and length 83fffc
[    0.368000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000e00000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=840000
[    0.432000] 0x0000005c0000-0x000000e00000 : "rootfs_data"
[    0.444000] 0x000000e00000-0x000000fe0000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000e00000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.488000] Registered led device: HW556:red:message
[    0.492000] Registered led device: HW556:red:hspa
[    0.492000] Registered led device: HW556:red:dsl
[    0.492000] Registered led device: HW556:red:power
[    0.492000] Registered led device: HW556:red:all
[    0.496000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.504000] 8021q: 802.1Q VLAN Support v1.8
[    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 200k freed
[    3.476000] eth0: link forced UP - 100/full - flow control off/off
[    3.708000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.772000] There is already a switch registered on the device 'eth0'
[    6.228000] Button Hotplug driver version 0.4.1
[   10.248000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 21 of xref (0 dead, 12 orphan) found.
[   13.924000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   13.932000] Backport based on wireless-testing.git master-2012-09-07
[   13.936000] compat.git: wireless-testing.git
[   14.004000] cfg80211: Calling CRDA to update world regulatory domain
[   14.008000] cfg80211: World regulatory domain updated:
[   14.016000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   14.024000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.032000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.040000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.048000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.056000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.656000] SCSI subsystem initialized
[   14.748000] There is already a switch registered on the device 'eth0'
[   15.012000] usbcore: registered new interface driver usbfs
[   15.016000] usbcore: registered new interface driver hub
[   15.024000] usbcore: registered new device driver usb
[   16.324000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.340000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   16.348000] ath: phy0: random mac address will be used: 4a:e5:14:fc:bb:9d
[   16.356000] ath: EEPROM regdomain: 0x0
[   16.356000] ath: EEPROM indicates default country code should be used
[   16.356000] ath: doing EEPROM country->regdmn map search
[   16.356000] ath: country maps to regdmn code: 0x3a
[   16.356000] ath: Country alpha2 being used: US
[   16.356000] ath: Regpair used: 0x3a
[   16.368000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.372000] Registered led device: ath9k-phy0
[   16.372000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[   16.380000] cfg80211: Calling CRDA for country: US
[   16.384000] cfg80211: Regulatory domain changed to country: US
[   16.388000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.396000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   16.404000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   16.412000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.420000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.428000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   16.436000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   17.776000] PPP generic driver version 2.4.2
[   18.356000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.740000] NET: Registered protocol family 24
[   18.952000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.064000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.068000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.104000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.120000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.128000] hub 1-0:1.0: USB hub found
[   19.132000] hub 1-0:1.0: 2 ports detected
[   19.328000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[   19.656000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   20.240000] hub 1-1:1.0: USB hub found
[   20.252000] hub 1-1:1.0: 2 ports detected
[   20.376000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.380000] usb 1-2: new high-speed USB device number 3 using bcm63xx_ehci
[   20.484000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.488000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.496000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.564000] hub 2-0:1.0: USB hub found
[   20.568000] hub 2-0:1.0: 2 ports detected
[   20.744000] uhci_hcd: USB Universal Host Controller Interface driver
[   20.936000] usbcore: registered new interface driver usblp
[   20.960000] usb 1-1.1: new full-speed USB device number 4 using bcm63xx_ehci
[   21.016000] usbcore: registered new interface driver usbserial
[   21.024000] USB Serial support registered for generic
[   21.120000] usbcore: registered new interface driver usbserial_generic
[   21.124000] usbserial: USB Serial Driver core
[   21.176000] Initializing USB Mass Storage driver...
[   21.184000] usb 1-2: USB disconnect, device number 3
[   21.192000] scsi0 : usb-storage 1-2:1.0
[   21.200000] scsi1 : usb-storage 1-2:1.1
[   21.204000] usbcore: registered new interface driver usb-storage
[   21.208000] USB Mass Storage support registered.
[   21.428000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   21.512000] USB Serial support registered for FTDI USB Serial Device
[   21.520000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 83351918, ra == 8335189c
[   21.528000] Oops[#1]:
[   21.528000] Cpu 0
[   21.528000] $ 0   : 00000000 00000065 00000000 83350000
[   21.528000] $ 4   : 00000001 833738e0 00006001 00006001
[   21.528000] $ 8   : 00000008 80131d08 00000008 00000000
[   21.528000] $12   : 00000000 00000000 810255a0 74207265
[   21.528000] $16   : 8335583c 83376a58 83310c68 83376b64
[   21.528000] $20   : 83b53480 f7ffffff 83310c00 8024e244
[   21.528000] $24   : 00000018 00000000                  
[   21.528000] $28   : 8331e000 8331fc18 8024e264 8335189c
[   21.528000] Hi    : 00000006
[   21.528000] Lo    : 0000000b
[   21.528000] epc   : 83351918 0x83351918
[   21.528000]     Tainted: G           O
[   21.528000] ra    : 8335189c 0x8335189c
[   21.528000] Status: 10008403    KERNEL EXL IE
[   21.528000] Cause : 00800008
[   21.528000] BadVA : 00000000
[   21.528000] PrId  : 0002a010 (Broadcom BMIPS4350)
[   21.528000] Modules linked in: ftdi_sio(+) gpio_keys_polled usb_storage usbserial usblp uhci_hcd ohci_hcd nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat pppoe xt_conntrack xt_CT xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack ehci_hcd sd_mod pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc vfat fat ext4 jbd2 mbcache rt2800pci(O) ath9k(O) rt2800lib(O) ath9k_common(O) ath9k_hw(O) rt2x00pci(O) ath(O) rt2x00lib(O) nls_utf8 nls_iso8859_15 nls_cp852 nls_cp850 nls_cp437 mac80211(O) usbcore usb_common scsi_mod nls_base crc16 crc_itu_t crc_ccitt eeprom_93cx6 cfg80211(O) compat(O) arc4 aes_generic crypto_algapi button_hotplug(O) input_polldev input_core switch_robo(O) switch_core(O)
[   21.528000] Process insmod (pid: 493, threadinfo=8331e000, task=83b4d178, tls=77928440)
[   21.528000] Stack : 00000000 8331fc90 8334e7c0 00000000 8333d6d0 8331fce0 832adf80 00000001
[   21.528000]         802a0000 800ea5cc 8333d6d0 8334e7c0 ffffffef 8331fce0 832adf80 00000001
[   21.528000]         802a0000 800eb3ac 8334e7c0 8331d100 8331d100 00000008 fffffff5 80300000
[   21.528000]         0000a1ff 800ead68 8334e540 8334e7c0 8334e7c0 8334e540 8331fce0 800eb420
[   21.528000]         000041ed 8026c474 fffffffe 8334e7c0 00000000 8334e540 8333d6d0 832adf80
[   21.528000]         ...
[   21.528000] Call Trace:[<800ea5cc>] 0x800ea5cc
[   21.528000] [<800eb3ac>] 0x800eb3ac
[   21.528000] [<800ead68>] 0x800ead68
[   21.528000] [<800eb420>] 0x800eb420
[   21.528000] [<800ebeec>] 0x800ebeec
[   21.528000] [<8304bdbc>] 0x8304bdbc
[   21.528000] [<8016dacc>] 0x8016dacc
[   21.528000] [<8016dd58>] 0x8016dd58
[   21.528000] [<8304bc78>] 0x8304bc78
[   21.528000] [<8016de78>] 0x8016de78
[   21.528000] [<8016c2ac>] 0x8016c2ac
[   21.528000] [<8016de0c>] 0x8016de0c
[   21.528000] [<8016c5c4>] 0x8016c5c4
[   21.528000] [<801293c4>] 0x801293c4
[   21.528000] [<8016d55c>] 0x8016d55c
[   21.528000] [<8016d69c>] 0x8016d69c
[   21.528000] [<8016e23c>] 0x8016e23c
[   21.528000] [<8304b488>] 0x8304b488
[   21.528000] [<83350cb8>] 0x83350cb8
[   21.528000] [<83370000>] 0x83370000
[   21.528000] [<833770c4>] 0x833770c4
[   21.528000] [<83377000>] 0x83377000
[   21.528000] [<80010900>] 0x80010900
[   21.528000] [<80094e28>] 0x80094e28
[   21.528000] [<8004dba4>] 0x8004dba4
[   21.528000] [<80062164>] 0x80062164
[   21.528000] [<8001a750>] 0x8001a750
[   21.528000] [<80131cf8>] 0x80131cf8
[   21.528000]
[   21.528000]
[   21.528000] Code: 108303bf  3c038335  8c420140 <8c430000> 24630001  ac430000  3c038335  24645830  0c091862
[   21.856000] ---[ end trace 61fc588ad063834b ]---
[   21.904000] fuse init (API version 7.18)
[   26.284000] usb 1-2: new high-speed USB device number 5 using bcm63xx_ehci
[   26.452000] scsi6 : usb-storage 1-2:1.4
[   26.460000] scsi7 : usb-storage 1-2:1.5
[   27.220000] eth0: link forced UP - 100/full - flow control off/off
[   27.248000] device eth0 entered promiscuous mode
[   27.260000] br-lan: port 1(eth0) entered forwarding state
[   27.264000] br-lan: port 1(eth0) entered forwarding state
[   27.456000] scsi 6:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[   27.488000] scsi 7:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[   27.508000] sd 7:0:0:0: [sda] Attached SCSI removable disk
[   29.268000] br-lan: port 1(eth0) entered forwarding state
[   32.356000] device wlan0 entered promiscuous mode
[   34.760000] br-lan: port 2(wlan0) entered forwarding state
[   34.764000] br-lan: port 2(wlan0) entered forwarding state
[   36.768000] br-lan: port 2(wlan0) entered forwarding state
[/spoiler]

I don't see any other missing dependences...
I'd suggest building openwrt by using the patches I provide or using my repo (https://github.com/Noltari/attitude_adjustment).
Sometimes the "--force-depends" feature doesn't work, so it's better to build your own openwrt firmware with the packages that you want.


Desconectado Tki2000

  • Moderador
  • *
  • Mensajes: 2247
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #890 en: 19-11-2012, 20:35 (Lunes) »
Hola.

Una pregunta sobre esta versión de openWrt y los pinchos 3G. ¿Alguien ha conseguido hacerlos funcionar? Para mi es de vital importancia acoplar un pincho 3G al openWrt y no he conseguido hacerlo. Siempre se produce un fallo de página en el kernel:

CPU 0 Unable to handle kernel paging request at virtual address... blah blah blah

He visto que alguien ya preguntó por esto mismo en la página 7 y desde entonces no he visto que se haya solucionado. Parece ser un problema con kmod-usb-serial

He probado con 3 pinchos Huawei distintos y con varias versiones de openWrt. La última con la que he probado (33935) también adolece de este síntoma.

¿Alguien ha conseguido hacer funcionar esto?

 :(


darkvier

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #891 en: 19-11-2012, 22:19 (Lunes) »
http://212.166.190.34/zonadescargas/Guia_identificacion_versiones.pdf

Al parecer hay tres versiones del router y en vodafone los diferencian por el Numero de serie
¡Muchas gracias por la información!
¿Sabemos de dónde ha salido :P?

Cuando tenga un rato la añado a la wiki.

Pues de la pagina de soporte de vodafone: link

« Última modificación: 19-11-2012, 22:33 (Lunes) por Noltari »

peterpunk

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #892 en: 21-11-2012, 10:15 (Miércoles) »
Hola.
En alguna parte del post se hace alusión a instalar webcam usb pero no deja claro como hacerlo o si lo ha conseguido ( o no me entero).
Al grano.
Estoy intentando instalar una webcam. El modelo concreto Aiptek Pocket DV5900, (Una autentica reliquia)

He instalado el paquete lsusb que indica:

Código: [Seleccionar]
root@OpenWrt:/mnt/usb# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 0424:2502 Standard Microsystems Corp.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 08ca:2024 Aiptek International, Inc. Pocket DV3500
Bus 001 Device 004: ID 0204:6025 Chipsbank Microelectronics Co., Ltd CBM2080 Flash drive controller

No se porqué razon cambia de modelo de camara, pero al menos reconoce la marca...

he intentado instalar los paquetes que indica
http://wiki.openwrt.org/doc/howto/usb.video

Pero para casi todos da error, incluso instalandolos con --force-depend

[spoiler=log de instalacion]
root@OpenWrt:/mnt/usb# opkg update
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/Packages.gz.
Inflating http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/Packages.gz.
Updated list of available packages in /var/opkg-lists/attitude_adjustment.

root@OpenWrt:/mnt/usb# opkg install kmod-video-core
Installing kmod-video-core (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-core_3.3.8-1_brcm63xx.ipk.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-core:
 *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *   kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *
 * opkg_install_cmd: Cannot install package kmod-video-core.

root@OpenWrt:/mnt/usb# opkg install --force-depend kmod-video-core
Installing kmod-video-core (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-core_3.3.8-1_brcm63xx.ipk.
Installing kmod-i2c-core (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-i2c-core_3.3.8-1_brcm63xx.ipk.
Configuring kmod-i2c-core.
Configuring kmod-video-core.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-core:
 *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *   kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:/mnt/usb# opkg install --force-depend kmod-video-cpia2
Installing kmod-video-cpia2 (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx                                                                             /generic/packages/kmod-video-cpia2_3.3.8-1_brcm63xx.ipk.
Configuring kmod-video-cpia2.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-                                                                             video-cpia2:
 *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:/dev# opkg install --force-depend kmod-video-pwc
Installing kmod-video-pwc (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-pwc_3.3.8-1_brcm63xx.ipk.
Installing kmod-video-videobuf2 (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-videobuf2_3.3.8-1_brcm63xx.ipk.
Configuring kmod-video-videobuf2.
Configuring kmod-video-pwc.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-pwc:
 *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *   kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:/dev# opkg install --force-depend kmod-video-uvc
Installing kmod-video-uvc (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-uvc_3.3.8-1_brcm63xx.ipk.
Configuring kmod-video-uvc.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-uvc:
 *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:/dev# opkg install --force-depend kmod-video-sn9c102
Installing kmod-video-sn9c102 (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-sn9c102_3.3.8-1_brcm63xx.ipk.
Configuring kmod-video-sn9c102.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-sn9c102:
 *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:/mnt/usb# opkg install --force-depend kmod-video-gspca-sunplus
Installing kmod-video-gspca-sunplus (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-gspca-sunplus_3.3.8-1_brcm63xx.ipk.
Installing kmod-video-gspca-core (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-gspca-core_3.3.8-1_brcm63xx.ipk.
Configuring kmod-video-gspca-core.
Configuring kmod-video-gspca-sunplus.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-gspca-sunplus:
  *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *   kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:/dev# opkg install --force-depend kmod-video-gspca-spca500
Installing kmod-video-gspca-spca500 (3.3.8-1) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/kmod-video-gspca-spca500_3.3.8-1_brcm63xx.ipk.
Configuring kmod-video-gspca-spca500.
Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-video-gspca-spca500:
  *      kernel (= 3.3.8-1-f7b19a853fcc6494bd48aec653b15eda) *

root@OpenWrt:~# opkg install mjpg-streamer
Installing mjpg-streamer (r148-4) to root...
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-beta/brcm63xx/generic/packages/mjpg-streamer_r148-4_brcm63xx.ipk.
Configuring mjpg-streamer.
[/spoiler]


El caso es que en /dev/ no aparece ningun archivo de tipo video

Por lo tanto sigue sin reconocer la camara.
¿Como hago para que la reconozca?




« Última modificación: 21-11-2012, 10:36 (Miércoles) por peterpunk »

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #893 en: 21-11-2012, 11:13 (Miércoles) »
El comando correcto es opkg install nombre_del_paquete --force-depends (te falta una 's').
De todas formas, es posible que no te funcione, así que te tocará compilarte el firm ...  ^-^


peterpunk

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #894 en: 21-11-2012, 11:52 (Miércoles) »
Pos vale.
He repetido todo con force-depends y continuan los errores. Pos a recompilar.
Pregunta. Tal vez deberia saber la respuesta, disculpa si es tan obvia que ofende.

¿Porque unos paquetes se instalan sin problema y otros es necesario recompilar?
Entiendo que ¿al recompilar tendre que montar la instalación completa con todos los paquetes incluyendo los que ya estaban en el paquete básico?



Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4607
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #895 en: 21-11-2012, 13:01 (Miércoles) »
Los paquetes que dan 'problemas' son los que dependen de la versión del kernel. Si este no coincide (el kernel que tenemos instalado en el router, y el del paquete que estamos instalando) es cuando podemos 'forzar' la instalación. Unas veces funciona y ... otras no  ^-^

Entiendo que ¿al recompilar tendre que montar la instalación completa con todos los paquetes incluyendo los que ya estaban en el paquete básico?

Mandeee ??  ;D
Antes de hacer más preguntas, lo mejor es que te leas el hilo correspondiente  ;) : https://foro.seguridadwireless.net/openwrt/compilar-openwrt-a-nuestro-gusto/


peterpunk

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #896 en: 22-11-2012, 17:05 (Jueves) »
Antes de hacer más preguntas, lo mejor es que te leas el hilo correspondiente  ;) : https://foro.seguridadwireless.net/openwrt/compilar-openwrt-a-nuestro-gusto/

Ya me la habia leido... pregunto por este tema, a ver si puedo continuar...


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #897 en: 25-11-2012, 03:17 (Domingo) »
Actualizados los parches para el SVN del primer post.
Llevo un par de semanas MUY LIADO con la universidad, por lo que no tengo mucho tiempo...
Así que si alguien quiere compilar un firmware con los parches y subirlo se lo agradecería.

A parte de eso, jogo ha integrado mis parches para el led pin y para el wifi de los ralink.
https://dev.openwrt.org/changeset/34321
https://dev.openwrt.org/changeset/34322

Por tanto, sólo quedan los parches de la placa y de los fixup para detectar los cal_data de cada modelo.
Antes de mandar estos parches, tengo que hablar con jogo para que actualice su parche del mtd, de modo que los cal_data no se borren si no están situados al final de la flash junto al nvram, como es el caso de los HW556. Aun así, como ya he dicho estoy bastante ocupado y no sé si esto será dentro de poco o más adelante.

Saludos!

« Última modificación: 25-11-2012, 03:19 (Domingo) por Noltari »

Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #898 en: 25-11-2012, 21:26 (Domingo) »
Últimos parches mandados (generación firmware, profile, parches placa, etc.).

Esperando impaciente a que jogo los aplique :D.


Noltari

  • Visitante
Re: [Desarrollo] OpenWrt en Huawei HG556a
« Respuesta #899 en: 26-11-2012, 12:15 (Lunes) »
Cuando tengáis un rato necesito que probéis este firmware (borrando todo, no me vale actualizar, por lo que si es desde el CFE mejor):
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r34380.bin

No estoy seguro de que funcione en Ralink, porque jogo me ha hecho cambiar los parches para que haya distintas definciones de placa, una para cada versión, y no sé si el script de extracción del cal_data del Ralink debería ir con el nombre "HW556" o "HW556_A".
También podéis probar que funcione todo, como, por ejemplo, el LED del WiFi en los atheros, etc.

Saludos!