Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a  (Leído 1910964 veces)

0 Usuarios y 3 Visitantes están viendo este tema.

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #440 en: 15-07-2012, 17:58 (Domingo) »
no se sí te sirva de algo, pero te envió el bootlog del firmware de danitool, que esta publicado en la primera pagina (el especifico para 29LV128DBT)

[spoiler]

CFE version cfe.d081.5003 for BCM96358 (32bit,SP,BE)
Build Date: Wed Nov 11 10:36:35 CST 2009 (Lihua_68693)
Copyright (C) 2006 Huawei Technologies Co. Ltd.


Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.

@w45260: Flash Manufacture id :c2

@w45260Flash Device id :227a

@w45260flipCFIGeometry:0
Parallel flash device: name MX29LV128DB, id 0x227a, size 16384KB
*** GetHG556aBoardVersion = <0> ***

CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
Total memory: 67108864 bytes (64MB)

Total memory used by CFE:  0x80401000 - 0x8052A510 (1217808)
Initialized Data:          0x8041F3C0 - 0x80421B60 (10144)
BSS Area:                  0x80421B60 - 0x80428510 (27056)
Local Heap:                0x80428510 - 0x80528510 (1048576)
Stack Area:                0x80528510 - 0x8052A510 (8192)
Text (code) segment:       0x80401000 - 0x8041F3B4 (123828)
Boot area (physical):      0x0052B000 - 0x0056B000
Relocation Factor:         I:00000000 - D:00000000

*** GetHG556aBoardVersion = <0> ***

Board IP address                  : 192.168.1.1
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id Name                     : HW556
Psi size in KB                    : 64
Number of MAC Addresses (1-32)    : 10
Base MAC Address                  : 64:16:f0:0a:87:2d
Ethernet PHY Type                 : Internal
Memory size in MB                 : 64
CMT Thread Number                 : 1

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
boot kernel from be020100
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[    0.000000] Linux version 2.6.39.4 (dani@tool) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #34 Wed Jan 4 22:16:19 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 62016k/65536k available (2145k kernel code, 3520k reserved, 368k data, 160k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.064000] MPI_CSBASE_REG(0) = 0x1e000000
[    0.068000] changed ath9k regdomain to 0xff
[    0.072000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] pci 0000:00:01.0: fixup device configuration
[    0.096000] pci-ath9k-fixup: Writing 0x0029168c to register 0x6000
[    0.100000] pci-ath9k-fixup: Writing 0x02800001 to register 0x6008
[    0.104000] pci-ath9k-fixup: Writing 0x2091168c to register 0x602c
[    0.108000] pci-ath9k-fixup: Writing 0x002a168c to register 0x5000
[    0.112000] pci-ath9k-fixup: Writing 0x02800001 to register 0x5008
[    0.116000] pci-ath9k-fixup: Writing 0x2091168c to register 0x502c
[    0.120000] pci-ath9k-fixup: Writing 0x05040cc0 to register 0x5064
[    0.124000] pci-ath9k-fixup: Writing 0x00033811 to register 0x506c
[    0.128000] pci-ath9k-fixup: Writing 0x0040073b to register 0x4004
[    0.132000] pci-ath9k-fixup: Writing 0x00000003 to register 0x4074
[    0.136000] pci-ath9k-fixup: Writing 0x01c20000 to register 0x4000
[    0.140000] pci-ath9k-fixup: Writing 0x00000044 to register 0x6034
[    0.144000] pci-ath9k-fixup: Device vendor 0x168c, id 0x0029
[    0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.168000] pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x3000ffff] (PCI address [0x30000000-0x3000ffff])
[    0.172000] Switching to clocksource MIPS
[    0.184000] NET: Registered protocol family 2
[    0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.196000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.204000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.212000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.216000] TCP reno registered
[    0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.236000] NET: Registered protocol family 1
[    0.240000] audit: initializing netlink socket (disabled)
[    0.248000] type=2000 audit(0.248:1): initialized
[    0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.260000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.272000] msgmni has been set to 121
[    0.276000] io scheduler noop registered
[    0.280000] io scheduler deadline registered (default)
[    0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.292000] console [ttyS0] enabled, bootconsole disabled
[    0.292000] console [ttyS0] enabled, bootconsole disabled
[    0.308000] bcm963xx-flash bcm963xx-flash.0: 0x02000000 at 0x1e000000
[    0.316000] Number of erase regions: 2
[    0.320000] Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
[    0.328000] Primary Algorithm Table at 0040
[    0.332000] Alternative Vendor Command Set: 0000 (None)
[    0.336000] No Alternate Algorithm Table
[    0.340000] Vcc Minimum:  3.0 V
[    0.344000] Vcc Maximum:  3.6 V
[    0.348000] No Vpp line
[    0.348000] Typical byte/word write timeout: 16 µs
[    0.356000] Maximum byte/word write timeout: 512 µs
[    0.360000] Full buffer write not supported
[    0.364000] Typical block erase timeout: 1024 ms
[    0.368000] Maximum block erase timeout: 16384 ms
[    0.372000] Chip erase not supported
[    0.376000] Device size: 0x1000000 bytes (16 MiB)
[    0.380000] Flash Device Interface description: 0x0002
[    0.388000]   - supports x8 and x16 via BYTE# with asynchronous interface
[    0.392000] Max. bytes in buffer write: 0x1
[    0.400000] Number of Erase Block Regions: 2
[    0.404000]   Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
[    0.408000]   Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
[    0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
[    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.432000]   Amd/Fujitsu Extended Query version 1.3.
[    0.436000]   Silicon revision: 0
[    0.440000]   Address sensitive unlock: Required
[    0.444000]   Erase Suspend: Read/write
[    0.448000]   Block protection: 4 sectors per group
[    0.452000]   Temporary block unprotect: Supported
[    0.460000]   Block protect/unprotect scheme: 4
[    0.464000]   Number of simultaneous operations: 0
[    0.468000]   Burst mode: Not supported
[    0.472000]   Page mode: Not supported
[    0.476000]   Vpp Supply Minimum Program/Erase Voltage: 10.5 V
[    0.480000]   Vpp Supply Maximum Program/Erase Voltage: 11.5 V
[    0.488000]   Top/Bottom Boot Block: Bottom boot
[    0.492000] number of CFI chips: 1
[    0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
[    0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
[    0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
[    0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
[    0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
[    0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
[    0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
[    0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
[    0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
[    0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
[    0.568000] Creating 6 MTD partitions on "bcm963xx":
[    0.576000] 0x000000000000-0x000000020000 : "CFE"
[    0.584000] 0x000000020100-0x000000100000 : "kernel"
[    0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.604000] 0x000000100000-0x000000e00000 : "rootfs"
[    0.612000] mtd: partition "rootfs" set to be root filesystem
[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[    0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
[    0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
[    0.648000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.656000] 0x000000020000-0x000000e00000 : "linux"
[    0.672000] bcm63xx-wdt bcm63xx-wdt.0:  started, timer margin: 30 sec
[    0.684000] TCP westwood registered
[    0.688000] NET: Registered protocol family 17
[    0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    0.700000] All bugs added by David S. Miller <davem@redhat.com>
[    0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.724000] Freeing unused kernel memory: 160k freed
awk: /proc/cpuinfo: No such file or directory
[    3.592000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.660000] There is already a switch registered on the device 'eth0'
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    9.284000] JFFS2 notice: (317) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 5 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [   12.800000] Compat-wireless backport release: compat-wireless-2011-11-29
[   12.808000] Backport based on wireless-testing.git master-2011-12-01
[   13.032000] cfg80211: Calling CRDA to update world regulatory domain
[   13.844000] cfg80211: World regulatory domain updated:
[   13.852000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.860000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.868000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.876000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.884000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.892000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.580000] SCSI subsystem initialized
[   14.680000] There is already a switch registered on the device 'eth0'
[   15.076000] usbcore: registered new interface driver usbfs
[   15.084000] usbcore: registered new interface driver hub
[   15.096000] usbcore: registered new device driver usb
[   16.680000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.688000] board_bcm963xx: Setting device platform data
[   16.700000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   16.708000] ath: random mac address will be used: 2e:d2:a1:a8:80:0b
[   16.728000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[   16.740000] cfg80211: Calling CRDA for country: JP
[   16.892000] cfg80211: Regulatory domain changed to country: JP
[   16.900000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.908000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.916000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.924000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.932000] cfg80211:     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.940000] cfg80211:     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.948000] cfg80211:     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.952000] cfg80211:     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.960000] cfg80211:     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.968000] cfg80211:     (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.976000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.984000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.992000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   17.040000] Button Hotplug driver version 0.4.1
[   18.016000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   18.568000] PPP generic driver version 2.4.2
[   18.796000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   19.120000] NET: Registered protocol family 24
[   19.368000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.372000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.380000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.412000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.428000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.436000] hub 1-0:1.0: USB hub found
[   19.440000] hub 1-0:1.0: 2 ports detected
[   19.756000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
[   19.876000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
[   20.260000] hub 1-1:1.0: USB hub found
[   20.272000] hub 1-1:1.0: 2 ports detected
[   20.680000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.684000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.692000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.700000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.768000] hub 2-0:1.0: USB hub found
[   20.772000] hub 2-0:1.0: 1 port detected
[   21.052000] Initializing USB Mass Storage driver...
[   21.056000] usbcore: registered new interface driver usb-storage
[   21.064000] USB Mass Storage support registered.
[   21.276000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[   23.288000] eth0: link forced UP - 100/full - flow control off/off
[   23.732000] device eth0 entered promiscuous mode
[   23.828000] br-lan: port 1(eth0) entering forwarding state
[   23.832000] br-lan: port 1(eth0) entering forwarding state[/spoiler] es esl bootlog que me da la ventana serie

[spoiler]Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.348000] No Vpp line
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.348000] Typical byte/word write timeout: 16 µs
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.356000] Maximum byte/word write timeout: 512 µs
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.360000] Full buffer write not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.364000] Typical block erase timeout: 1024 ms
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.368000] Maximum block erase timeout: 16384 ms
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.372000] Chip erase not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.376000] Device size: 0x1000000 bytes (16 MiB)
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.404000]   Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.408000]   Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.424000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.432000]   Amd/Fujitsu Extended Query version 1.3.
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.436000]   Silicon revision: 0
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.440000]   Address sensitive unlock: Required
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.444000]   Erase Suspend: Read/write
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.448000]   Block protection: 4 sectors per group
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.452000]   Temporary block unprotect: Supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.460000]   Block protect/unprotect scheme: 4
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.464000]   Number of simultaneous operations: 0
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.468000]   Burst mode: Not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.472000]   Page mode: Not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.476000]   Vpp Supply Minimum Program/Erase Voltage: 10.5 V
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.480000]   Vpp Supply Maximum Program/Erase Voltage: 11.5 V
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.488000]   Top/Bottom Boot Block: Bottom boot
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.492000] number of CFI chips: 1
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.584000] 0x000000020100-0x000000100000 : "kernel"
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.604000] 0x000000100000-0x000000e00000 : "rootfs"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.612000] mtd: partition "rootfs" set to be root filesystem
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.648000] 0x000000fe0000-0x000001000000 : "nvram"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.656000] 0x000000020000-0x000000e00000 : "linux"
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.672000] bcm63xx-wdt bcm63xx-wdt.0:  started, timer margin: 30 sec
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: message
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: hspa
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: dsl
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: power
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: all_leds
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.684000] TCP westwood registered
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.688000] NET: Registered protocol family 17
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.700000] All bugs added by David S. Miller <davem@redhat.com>
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.724000] Freeing unused kernel memory: 160k freed
Sep  8 15:44:11 OpenWrt kern.info kernel: [    3.584000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    4.656000] There is already a switch registered on the device 'eth0'
Sep  8 15:44:11 OpenWrt kern.info kernel: [   12.672000] Compat-wireless backport release: compat-wireless-2011-11-29
Sep  8 15:44:11 OpenWrt kern.info kernel: [   12.680000] Backport based on wireless-testing.git master-2011-12-01
Sep  8 15:44:11 OpenWrt kern.info kernel: [   12.904000] cfg80211: Calling CRDA to update world regulatory domain
Sep  8 15:44:11 OpenWrt kern.info kernel: [   13.760000] cfg80211: World regulatory domain updated:
Sep  8 15:44:11 OpenWrt kern.info kernel: [   13.764000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   13.808000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.notice kernel: [   14.452000] SCSI subsystem initialized
Sep  8 15:44:11 OpenWrt kern.warn kernel: [   14.552000] There is already a switch registered on the device 'eth0'
Sep  8 15:44:11 OpenWrt kern.info kernel: [   14.952000] usbcore: registered new interface driver usbfs
Sep  8 15:44:11 OpenWrt kern.info kernel: [   14.956000] usbcore: registered new interface driver hub
Sep  8 15:44:11 OpenWrt kern.info kernel: [   14.968000] usbcore: registered new device driver usb
Sep  8 15:44:11 OpenWrt kern.warn kernel: [   16.552000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.560000] board_bcm963xx: Setting device platform data
Sep  8 15:44:11 OpenWrt kern.err kernel: [   16.576000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
Sep  8 15:44:11 OpenWrt kern.err kernel: [   16.580000] ath: random mac address will be used: 22:9f:90:3e:7a:be
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: EEPROM regdomain: 0xff
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: EEPROM indicates we should expect a direct regpair map
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: Country alpha2 being used: JP
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: Regpair used: 0xff
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.600000] Registered led device: ath9k-phy0
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.600000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.612000] cfg80211: Calling CRDA for country: JP
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.776000] cfg80211: Regulatory domain changed to country: JP
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.784000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.792000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.800000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.808000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.816000] cfg80211:     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.824000] cfg80211:     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.832000] cfg80211:     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.840000] cfg80211:     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.848000] cfg80211:     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.872000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.880000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.916000] Button Hotplug driver version 0.4.1
Sep  8 15:44:11 OpenWrt kern.info kernel: [   17.892000] NTFS driver 2.1.30 [Flags: R/O MODULE].
Sep  8 15:44:11 OpenWrt kern.info kernel: [   18.444000] PPP generic driver version 2.4.2
Sep  8 15:44:11 OpenWrt kern.info kernel: [   18.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sep  8 15:44:11 OpenWrt kern.info kernel: [   18.996000] NET: Registered protocol family 24
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.248000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.252000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.260000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.292000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.308000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.316000] hub 1-0:1.0: USB hub found
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.320000] hub 1-0:1.0: 2 ports detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.640000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.756000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.140000] hub 1-1:1.0: USB hub found
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.152000] hub 1-1:1.0: 2 ports detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.568000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.576000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.584000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.648000] hub 2-0:1.0: USB hub found
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.652000] hub 2-0:1.0: 1 port detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.932000] Initializing USB Mass Storage driver...
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.940000] usbcore: registered new interface driver usb-storage
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.944000] USB Mass Storage support registered.
Sep  8 15:44:11 OpenWrt kern.info kernel: [   21.156000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
Sep  8 15:44:12 OpenWrt kern.info kernel: [   23.808000] eth0: link forced UP - 100/full - flow control off/off
Sep  8 15:44:12 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Sep  8 15:44:12 OpenWrt kern.info kernel: [   24.220000] device eth0 entered promiscuous mode
Sep  8 15:44:12 OpenWrt kern.info kernel: [   24.320000] br-lan: port 1(eth0) entering forwarding state
Sep  8 15:44:12 OpenWrt kern.info kernel: [   24.328000] br-lan: port 1(eth0) entering forwarding state
Sep  8 15:44:14 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:15 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:15 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Sep  8 15:44:18 OpenWrt user.info sysinit: Loading defaults
Sep  8 15:44:18 OpenWrt user.info sysinit: Loading synflood protection
Sep  8 15:44:19 OpenWrt user.info sysinit: Adding custom chains
Sep  8 15:44:20 OpenWrt user.info sysinit: Loading zones
Sep  8 15:44:21 OpenWrt user.info sysinit: Loading forwardings
Sep  8 15:44:21 OpenWrt user.info sysinit: Loading redirects
Sep  8 15:44:21 OpenWrt user.info sysinit: Loading rules
Sep  8 15:44:22 OpenWrt user.info sysinit: Loading includes
Sep  8 15:44:22 OpenWrt user.info sysinit: Optimizing conntrack
Sep  8 15:44:22 OpenWrt user.info sysinit: Loading interfaces
Sep  8 15:44:22 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Sep  8 15:44:25 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sep  8 15:44:25 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: started, version 2.59 cachesize 150
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: compile time options: IPv6 GNU-getopt no-DBus no-i18n DHCP TFTP no-conntrack no-IDN
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq-dhcp[956]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: using local addresses only for domain lan
Sep  8 15:44:29 OpenWrt daemon.warn dnsmasq[956]: no servers found in /tmp/resolv.conf.auto, will retry
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: read /etc/hosts - 1 addresses
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq-dhcp[956]: read /etc/ethers - 0 addresses
Sep  8 15:44:30 OpenWrt kern.warn kernel: [   41.976000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
Sep  8 15:44:30 OpenWrt kern.warn kernel: [   41.984000] jffs2_build_filesystem(): unlocking the mtd device... done.
Sep  8 15:46:08 OpenWrt kern.warn kernel: [   41.988000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
Sep  8 15:46:08 OpenWrt kern.notice kernel: [  139.712000] JFFS2 notice: (978) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sep  8 15:46:08 OpenWrt auth.err passwd: /etc/passwd: Read-only file system
Sep  8 15:46:08 OpenWrt auth.err passwd: can't update password file /etc/passwd
Sep  8 15:46:08 OpenWrt user.info sysinit: copying files ... done
Sep  8 15:46:10 OpenWrt authpriv.info dropbear[1766]: Running in background
[/spoiler] esto es el system log de luci

[spoiler][    0.000000] Linux version 2.6.39.4 (dani@tool) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #34 Wed Jan 4 22:16:19 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802840e0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 62016k/65536k available (2145k kernel code, 3520k reserved, 368k data, 160k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.064000] MPI_CSBASE_REG(0) = 0x1e000000
[    0.068000] changed ath9k regdomain to 0xff
[    0.072000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.092000] pci 0000:00:01.0: fixup device configuration
[    0.096000] pci-ath9k-fixup: Writing 0x0029168c to register 0x6000
[    0.100000] pci-ath9k-fixup: Writing 0x02800001 to register 0x6008
[    0.104000] pci-ath9k-fixup: Writing 0x2091168c to register 0x602c
[    0.108000] pci-ath9k-fixup: Writing 0x002a168c to register 0x5000
[    0.112000] pci-ath9k-fixup: Writing 0x02800001 to register 0x5008
[    0.116000] pci-ath9k-fixup: Writing 0x2091168c to register 0x502c
[    0.120000] pci-ath9k-fixup: Writing 0x05040cc0 to register 0x5064
[    0.124000] pci-ath9k-fixup: Writing 0x00033811 to register 0x506c
[    0.128000] pci-ath9k-fixup: Writing 0x0040073b to register 0x4004
[    0.132000] pci-ath9k-fixup: Writing 0x00000003 to register 0x4074
[    0.136000] pci-ath9k-fixup: Writing 0x01c20000 to register 0x4000
[    0.140000] pci-ath9k-fixup: Writing 0x00000044 to register 0x6034
[    0.144000] pci-ath9k-fixup: Device vendor 0x168c, id 0x0029
[    0.148000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.160000] pci 0000:00:01.0: PME# supported from D0 D3hot
[    0.160000] pci 0000:00:01.0: PME# disabled
[    0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.168000] pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x3000ffff] (PCI address [0x30000000-0x3000ffff])
[    0.172000] Switching to clocksource MIPS
[    0.184000] NET: Registered protocol family 2
[    0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.196000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.204000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.212000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.216000] TCP reno registered
[    0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.236000] NET: Registered protocol family 1
[    0.240000] PCI: CLS 0 bytes, default 32
[    0.240000] audit: initializing netlink socket (disabled)
[    0.248000] type=2000 audit(0.248:1): initialized
[    0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.260000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.272000] msgmni has been set to 121
[    0.276000] io scheduler noop registered
[    0.280000] io scheduler deadline registered (default)
[    0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.292000] console [ttyS0] enabled, bootconsole disabled
[    0.308000] bcm963xx-flash bcm963xx-flash.0: 0x02000000 at 0x1e000000
[    0.316000] Number of erase regions: 2
[    0.320000] Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
[    0.328000] Primary Algorithm Table at 0040
[    0.332000] Alternative Vendor Command Set: 0000 (None)
[    0.336000] No Alternate Algorithm Table
[    0.340000] Vcc Minimum:  3.0 V
[    0.344000] Vcc Maximum:  3.6 V
[    0.348000] No Vpp line
[    0.348000] Typical byte/word write timeout: 16 µs
[    0.356000] Maximum byte/word write timeout: 512 µs
[    0.360000] Full buffer write not supported
[    0.364000] Typical block erase timeout: 1024 ms
[    0.368000] Maximum block erase timeout: 16384 ms
[    0.372000] Chip erase not supported
[    0.376000] Device size: 0x1000000 bytes (16 MiB)
[    0.380000] Flash Device Interface description: 0x0002
[    0.388000]   - supports x8 and x16 via BYTE# with asynchronous interface
[    0.392000] Max. bytes in buffer write: 0x1
[    0.400000] Number of Erase Block Regions: 2
[    0.404000]   Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
[    0.408000]   Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
[    0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
[    0.424000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
[    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.432000]   Amd/Fujitsu Extended Query version 1.3.
[    0.436000]   Silicon revision: 0
[    0.440000]   Address sensitive unlock: Required
[    0.444000]   Erase Suspend: Read/write
[    0.448000]   Block protection: 4 sectors per group
[    0.452000]   Temporary block unprotect: Supported
[    0.460000]   Block protect/unprotect scheme: 4
[    0.464000]   Number of simultaneous operations: 0
[    0.468000]   Burst mode: Not supported
[    0.472000]   Page mode: Not supported
[    0.476000]   Vpp Supply Minimum Program/Erase Voltage: 10.5 V
[    0.480000]   Vpp Supply Maximum Program/Erase Voltage: 11.5 V
[    0.488000]   Top/Bottom Boot Block: Bottom boot
[    0.492000] number of CFI chips: 1
[    0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
[    0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
[    0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
[    0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
[    0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
[    0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
[    0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
[    0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
[    0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
[    0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
[    0.568000] Creating 6 MTD partitions on "bcm963xx":
[    0.576000] 0x000000000000-0x000000020000 : "CFE"
[    0.584000] 0x000000020100-0x000000100000 : "kernel"
[    0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.604000] 0x000000100000-0x000000e00000 : "rootfs"
[    0.612000] mtd: partition "rootfs" set to be root filesystem
[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[    0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
[    0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
[    0.648000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.656000] 0x000000020000-0x000000e00000 : "linux"
[    0.672000] bcm63xx-wdt bcm63xx-wdt.0:  started, timer margin: 30 sec
[    0.680000] Registered led device: message
[    0.680000] Registered led device: hspa
[    0.680000] Registered led device: dsl
[    0.680000] Registered led device: power
[    0.680000] Registered led device: all_leds
[    0.684000] TCP westwood registered
[    0.688000] NET: Registered protocol family 17
[    0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    0.700000] All bugs added by David S. Miller <davem@redhat.com>
[    0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.724000] Freeing unused kernel memory: 160k freed
[    3.584000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.656000] There is already a switch registered on the device 'eth0'
[   12.672000] Compat-wireless backport release: compat-wireless-2011-11-29
[   12.680000] Backport based on wireless-testing.git master-2011-12-01
[   12.904000] cfg80211: Calling CRDA to update world regulatory domain
[   13.760000] cfg80211: World regulatory domain updated:
[   13.764000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.772000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.780000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.792000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.800000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.808000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.452000] SCSI subsystem initialized
[   14.552000] There is already a switch registered on the device 'eth0'
[   14.952000] usbcore: registered new interface driver usbfs
[   14.956000] usbcore: registered new interface driver hub
[   14.968000] usbcore: registered new device driver usb
[   16.552000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.560000] board_bcm963xx: Setting device platform data
[   16.576000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   16.580000] ath: random mac address will be used: 22:9f:90:3e:7a:be
[   16.588000] ath: EEPROM regdomain: 0xff
[   16.588000] ath: EEPROM indicates we should expect a direct regpair map
[   16.588000] ath: Country alpha2 being used: JP
[   16.588000] ath: Regpair used: 0xff
[   16.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.600000] Registered led device: ath9k-phy0
[   16.600000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[   16.612000] cfg80211: Calling CRDA for country: JP
[   16.776000] cfg80211: Regulatory domain changed to country: JP
[   16.784000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.792000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.800000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.808000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.816000] cfg80211:     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.824000] cfg80211:     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.832000] cfg80211:     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.840000] cfg80211:     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.848000] cfg80211:     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.856000] cfg80211:     (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.864000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.872000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.880000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.916000] Button Hotplug driver version 0.4.1
[   17.892000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   18.444000] PPP generic driver version 2.4.2
[   18.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.996000] NET: Registered protocol family 24
[   19.248000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.252000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.260000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.292000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.308000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.316000] hub 1-0:1.0: USB hub found
[   19.320000] hub 1-0:1.0: 2 ports detected
[   19.640000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
[   19.756000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
[   20.140000] hub 1-1:1.0: USB hub found
[   20.152000] hub 1-1:1.0: 2 ports detected
[   20.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.568000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.576000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.584000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.648000] hub 2-0:1.0: USB hub found
[   20.652000] hub 2-0:1.0: 1 port detected
[   20.932000] Initializing USB Mass Storage driver...
[   20.940000] usbcore: registered new interface driver usb-storage
[   20.944000] USB Mass Storage support registered.
[   21.156000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[   23.808000] eth0: link forced UP - 100/full - flow control off/off
[   24.220000] device eth0 entered promiscuous mode
[   24.320000] br-lan: port 1(eth0) entering forwarding state
[   24.328000] br-lan: port 1(eth0) entering forwarding state
[   41.976000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   41.984000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   41.988000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  139.712000] JFFS2 notice: (978) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler] esto es el kernel log de luci




Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #441 en: 15-07-2012, 18:12 (Domingo) »
no se sí te sirva de algo, pero te envió el bootlog del firmware de danitool, que esta publicado en la primera pagina (el especifico para 29LV128DBT)

[spoiler]

CFE version cfe.d081.5003 for BCM96358 (32bit,SP,BE)
Build Date: Wed Nov 11 10:36:35 CST 2009 (Lihua_68693)
Copyright (C) 2006 Huawei Technologies Co. Ltd.


Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.

@w45260: Flash Manufacture id :c2

@w45260Flash Device id :227a

@w45260flipCFIGeometry:0
Parallel flash device: name MX29LV128DB, id 0x227a, size 16384KB
*** GetHG556aBoardVersion = <0> ***

CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
Total memory: 67108864 bytes (64MB)

Total memory used by CFE:  0x80401000 - 0x8052A510 (1217808)
Initialized Data:          0x8041F3C0 - 0x80421B60 (10144)
BSS Area:                  0x80421B60 - 0x80428510 (27056)
Local Heap:                0x80428510 - 0x80528510 (1048576)
Stack Area:                0x80528510 - 0x8052A510 (8192)
Text (code) segment:       0x80401000 - 0x8041F3B4 (123828)
Boot area (physical):      0x0052B000 - 0x0056B000
Relocation Factor:         I:00000000 - D:00000000

*** GetHG556aBoardVersion = <0> ***

Board IP address                  : 192.168.1.1
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id Name                     : HW556
Psi size in KB                    : 64
Number of MAC Addresses (1-32)    : 10
Base MAC Address                  : 64:16:f0:0a:87:2d
Ethernet PHY Type                 : Internal
Memory size in MB                 : 64
CMT Thread Number                 : 1

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
boot kernel from be020100
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[    0.000000] Linux version 2.6.39.4 (dani@tool) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #34 Wed Jan 4 22:16:19 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 62016k/65536k available (2145k kernel code, 3520k reserved, 368k data, 160k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.064000] MPI_CSBASE_REG(0) = 0x1e000000
[    0.068000] changed ath9k regdomain to 0xff
[    0.072000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] pci 0000:00:01.0: fixup device configuration
[    0.096000] pci-ath9k-fixup: Writing 0x0029168c to register 0x6000
[    0.100000] pci-ath9k-fixup: Writing 0x02800001 to register 0x6008
[    0.104000] pci-ath9k-fixup: Writing 0x2091168c to register 0x602c
[    0.108000] pci-ath9k-fixup: Writing 0x002a168c to register 0x5000
[    0.112000] pci-ath9k-fixup: Writing 0x02800001 to register 0x5008
[    0.116000] pci-ath9k-fixup: Writing 0x2091168c to register 0x502c
[    0.120000] pci-ath9k-fixup: Writing 0x05040cc0 to register 0x5064
[    0.124000] pci-ath9k-fixup: Writing 0x00033811 to register 0x506c
[    0.128000] pci-ath9k-fixup: Writing 0x0040073b to register 0x4004
[    0.132000] pci-ath9k-fixup: Writing 0x00000003 to register 0x4074
[    0.136000] pci-ath9k-fixup: Writing 0x01c20000 to register 0x4000
[    0.140000] pci-ath9k-fixup: Writing 0x00000044 to register 0x6034
[    0.144000] pci-ath9k-fixup: Device vendor 0x168c, id 0x0029
[    0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.168000] pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x3000ffff] (PCI address [0x30000000-0x3000ffff])
[    0.172000] Switching to clocksource MIPS
[    0.184000] NET: Registered protocol family 2
[    0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.196000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.204000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.212000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.216000] TCP reno registered
[    0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.236000] NET: Registered protocol family 1
[    0.240000] audit: initializing netlink socket (disabled)
[    0.248000] type=2000 audit(0.248:1): initialized
[    0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.260000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.272000] msgmni has been set to 121
[    0.276000] io scheduler noop registered
[    0.280000] io scheduler deadline registered (default)
[    0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.292000] console [ttyS0] enabled, bootconsole disabled
[    0.292000] console [ttyS0] enabled, bootconsole disabled
[    0.308000] bcm963xx-flash bcm963xx-flash.0: 0x02000000 at 0x1e000000
[    0.316000] Number of erase regions: 2
[    0.320000] Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
[    0.328000] Primary Algorithm Table at 0040
[    0.332000] Alternative Vendor Command Set: 0000 (None)
[    0.336000] No Alternate Algorithm Table
[    0.340000] Vcc Minimum:  3.0 V
[    0.344000] Vcc Maximum:  3.6 V
[    0.348000] No Vpp line
[    0.348000] Typical byte/word write timeout: 16 µs
[    0.356000] Maximum byte/word write timeout: 512 µs
[    0.360000] Full buffer write not supported
[    0.364000] Typical block erase timeout: 1024 ms
[    0.368000] Maximum block erase timeout: 16384 ms
[    0.372000] Chip erase not supported
[    0.376000] Device size: 0x1000000 bytes (16 MiB)
[    0.380000] Flash Device Interface description: 0x0002
[    0.388000]   - supports x8 and x16 via BYTE# with asynchronous interface
[    0.392000] Max. bytes in buffer write: 0x1
[    0.400000] Number of Erase Block Regions: 2
[    0.404000]   Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
[    0.408000]   Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
[    0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
[    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.432000]   Amd/Fujitsu Extended Query version 1.3.
[    0.436000]   Silicon revision: 0
[    0.440000]   Address sensitive unlock: Required
[    0.444000]   Erase Suspend: Read/write
[    0.448000]   Block protection: 4 sectors per group
[    0.452000]   Temporary block unprotect: Supported
[    0.460000]   Block protect/unprotect scheme: 4
[    0.464000]   Number of simultaneous operations: 0
[    0.468000]   Burst mode: Not supported
[    0.472000]   Page mode: Not supported
[    0.476000]   Vpp Supply Minimum Program/Erase Voltage: 10.5 V
[    0.480000]   Vpp Supply Maximum Program/Erase Voltage: 11.5 V
[    0.488000]   Top/Bottom Boot Block: Bottom boot
[    0.492000] number of CFI chips: 1
[    0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
[    0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
[    0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
[    0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
[    0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
[    0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
[    0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
[    0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
[    0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
[    0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
[    0.568000] Creating 6 MTD partitions on "bcm963xx":
[    0.576000] 0x000000000000-0x000000020000 : "CFE"
[    0.584000] 0x000000020100-0x000000100000 : "kernel"
[    0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.604000] 0x000000100000-0x000000e00000 : "rootfs"
[    0.612000] mtd: partition "rootfs" set to be root filesystem
[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[    0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
[    0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
[    0.648000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.656000] 0x000000020000-0x000000e00000 : "linux"
[    0.672000] bcm63xx-wdt bcm63xx-wdt.0:  started, timer margin: 30 sec
[    0.684000] TCP westwood registered
[    0.688000] NET: Registered protocol family 17
[    0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    0.700000] All bugs added by David S. Miller <davem@redhat.com>
[    0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.724000] Freeing unused kernel memory: 160k freed
awk: /proc/cpuinfo: No such file or directory
[    3.592000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.660000] There is already a switch registered on the device 'eth0'
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    9.284000] JFFS2 notice: (317) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 5 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. [   12.800000] Compat-wireless backport release: compat-wireless-2011-11-29
[   12.808000] Backport based on wireless-testing.git master-2011-12-01
[   13.032000] cfg80211: Calling CRDA to update world regulatory domain
[   13.844000] cfg80211: World regulatory domain updated:
[   13.852000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.860000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.868000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.876000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.884000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.892000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.580000] SCSI subsystem initialized
[   14.680000] There is already a switch registered on the device 'eth0'
[   15.076000] usbcore: registered new interface driver usbfs
[   15.084000] usbcore: registered new interface driver hub
[   15.096000] usbcore: registered new device driver usb
[   16.680000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.688000] board_bcm963xx: Setting device platform data
[   16.700000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   16.708000] ath: random mac address will be used: 2e:d2:a1:a8:80:0b
[   16.728000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[   16.740000] cfg80211: Calling CRDA for country: JP
[   16.892000] cfg80211: Regulatory domain changed to country: JP
[   16.900000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.908000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.916000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.924000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.932000] cfg80211:     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.940000] cfg80211:     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.948000] cfg80211:     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.952000] cfg80211:     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.960000] cfg80211:     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.968000] cfg80211:     (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.976000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.984000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.992000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   17.040000] Button Hotplug driver version 0.4.1
[   18.016000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   18.568000] PPP generic driver version 2.4.2
[   18.796000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   19.120000] NET: Registered protocol family 24
[   19.368000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.372000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.380000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.412000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.428000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.436000] hub 1-0:1.0: USB hub found
[   19.440000] hub 1-0:1.0: 2 ports detected
[   19.756000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
[   19.876000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
[   20.260000] hub 1-1:1.0: USB hub found
[   20.272000] hub 1-1:1.0: 2 ports detected
[   20.680000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.684000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.692000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.700000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.768000] hub 2-0:1.0: USB hub found
[   20.772000] hub 2-0:1.0: 1 port detected
[   21.052000] Initializing USB Mass Storage driver...
[   21.056000] usbcore: registered new interface driver usb-storage
[   21.064000] USB Mass Storage support registered.
[   21.276000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[   23.288000] eth0: link forced UP - 100/full - flow control off/off
[   23.732000] device eth0 entered promiscuous mode
[   23.828000] br-lan: port 1(eth0) entering forwarding state
[   23.832000] br-lan: port 1(eth0) entering forwarding state[/spoiler] es esl bootlog que me da la ventana serie

[spoiler]Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.348000] No Vpp line
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.348000] Typical byte/word write timeout: 16 µs
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.356000] Maximum byte/word write timeout: 512 µs
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.360000] Full buffer write not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.364000] Typical block erase timeout: 1024 ms
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.368000] Maximum block erase timeout: 16384 ms
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.372000] Chip erase not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.376000] Device size: 0x1000000 bytes (16 MiB)
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.404000]   Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.408000]   Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.424000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.432000]   Amd/Fujitsu Extended Query version 1.3.
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.436000]   Silicon revision: 0
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.440000]   Address sensitive unlock: Required
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.444000]   Erase Suspend: Read/write
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.448000]   Block protection: 4 sectors per group
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.452000]   Temporary block unprotect: Supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.460000]   Block protect/unprotect scheme: 4
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.464000]   Number of simultaneous operations: 0
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.468000]   Burst mode: Not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.472000]   Page mode: Not supported
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.476000]   Vpp Supply Minimum Program/Erase Voltage: 10.5 V
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.480000]   Vpp Supply Maximum Program/Erase Voltage: 11.5 V
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.488000]   Top/Bottom Boot Block: Bottom boot
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.492000] number of CFI chips: 1
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.584000] 0x000000020100-0x000000100000 : "kernel"
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.604000] 0x000000100000-0x000000e00000 : "rootfs"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.612000] mtd: partition "rootfs" set to be root filesystem
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.648000] 0x000000fe0000-0x000001000000 : "nvram"
Sep  8 15:44:11 OpenWrt kern.notice kernel: [    0.656000] 0x000000020000-0x000000e00000 : "linux"
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.672000] bcm63xx-wdt bcm63xx-wdt.0:  started, timer margin: 30 sec
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: message
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: hspa
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: dsl
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: power
Sep  8 15:44:11 OpenWrt kern.debug kernel: [    0.680000] Registered led device: all_leds
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.684000] TCP westwood registered
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.688000] NET: Registered protocol family 17
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.700000] All bugs added by David S. Miller <davem@redhat.com>
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sep  8 15:44:11 OpenWrt kern.info kernel: [    0.724000] Freeing unused kernel memory: 160k freed
Sep  8 15:44:11 OpenWrt kern.info kernel: [    3.584000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
Sep  8 15:44:11 OpenWrt kern.warn kernel: [    4.656000] There is already a switch registered on the device 'eth0'
Sep  8 15:44:11 OpenWrt kern.info kernel: [   12.672000] Compat-wireless backport release: compat-wireless-2011-11-29
Sep  8 15:44:11 OpenWrt kern.info kernel: [   12.680000] Backport based on wireless-testing.git master-2011-12-01
Sep  8 15:44:11 OpenWrt kern.info kernel: [   12.904000] cfg80211: Calling CRDA to update world regulatory domain
Sep  8 15:44:11 OpenWrt kern.info kernel: [   13.760000] cfg80211: World regulatory domain updated:
Sep  8 15:44:11 OpenWrt kern.info kernel: [   13.764000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   13.808000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.notice kernel: [   14.452000] SCSI subsystem initialized
Sep  8 15:44:11 OpenWrt kern.warn kernel: [   14.552000] There is already a switch registered on the device 'eth0'
Sep  8 15:44:11 OpenWrt kern.info kernel: [   14.952000] usbcore: registered new interface driver usbfs
Sep  8 15:44:11 OpenWrt kern.info kernel: [   14.956000] usbcore: registered new interface driver hub
Sep  8 15:44:11 OpenWrt kern.info kernel: [   14.968000] usbcore: registered new device driver usb
Sep  8 15:44:11 OpenWrt kern.warn kernel: [   16.552000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.560000] board_bcm963xx: Setting device platform data
Sep  8 15:44:11 OpenWrt kern.err kernel: [   16.576000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
Sep  8 15:44:11 OpenWrt kern.err kernel: [   16.580000] ath: random mac address will be used: 22:9f:90:3e:7a:be
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: EEPROM regdomain: 0xff
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: EEPROM indicates we should expect a direct regpair map
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: Country alpha2 being used: JP
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.588000] ath: Regpair used: 0xff
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sep  8 15:44:11 OpenWrt kern.debug kernel: [   16.600000] Registered led device: ath9k-phy0
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.600000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.612000] cfg80211: Calling CRDA for country: JP
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.776000] cfg80211: Regulatory domain changed to country: JP
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.784000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.792000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.800000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.808000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.816000] cfg80211:     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.824000] cfg80211:     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.832000] cfg80211:     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.840000] cfg80211:     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.848000] cfg80211:     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.872000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.880000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   16.916000] Button Hotplug driver version 0.4.1
Sep  8 15:44:11 OpenWrt kern.info kernel: [   17.892000] NTFS driver 2.1.30 [Flags: R/O MODULE].
Sep  8 15:44:11 OpenWrt kern.info kernel: [   18.444000] PPP generic driver version 2.4.2
Sep  8 15:44:11 OpenWrt kern.info kernel: [   18.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sep  8 15:44:11 OpenWrt kern.info kernel: [   18.996000] NET: Registered protocol family 24
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.248000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.252000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.260000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.292000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.308000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.316000] hub 1-0:1.0: USB hub found
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.320000] hub 1-0:1.0: 2 ports detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.640000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
Sep  8 15:44:11 OpenWrt kern.info kernel: [   19.756000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.140000] hub 1-1:1.0: USB hub found
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.152000] hub 1-1:1.0: 2 ports detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.568000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.576000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.584000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.648000] hub 2-0:1.0: USB hub found
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.652000] hub 2-0:1.0: 1 port detected
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.932000] Initializing USB Mass Storage driver...
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.940000] usbcore: registered new interface driver usb-storage
Sep  8 15:44:11 OpenWrt kern.info kernel: [   20.944000] USB Mass Storage support registered.
Sep  8 15:44:11 OpenWrt kern.info kernel: [   21.156000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
Sep  8 15:44:12 OpenWrt kern.info kernel: [   23.808000] eth0: link forced UP - 100/full - flow control off/off
Sep  8 15:44:12 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Sep  8 15:44:12 OpenWrt kern.info kernel: [   24.220000] device eth0 entered promiscuous mode
Sep  8 15:44:12 OpenWrt kern.info kernel: [   24.320000] br-lan: port 1(eth0) entering forwarding state
Sep  8 15:44:12 OpenWrt kern.info kernel: [   24.328000] br-lan: port 1(eth0) entering forwarding state
Sep  8 15:44:14 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:15 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:15 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Sep  8 15:44:18 OpenWrt user.info sysinit: Loading defaults
Sep  8 15:44:18 OpenWrt user.info sysinit: Loading synflood protection
Sep  8 15:44:19 OpenWrt user.info sysinit: Adding custom chains
Sep  8 15:44:20 OpenWrt user.info sysinit: Loading zones
Sep  8 15:44:21 OpenWrt user.info sysinit: Loading forwardings
Sep  8 15:44:21 OpenWrt user.info sysinit: Loading redirects
Sep  8 15:44:21 OpenWrt user.info sysinit: Loading rules
Sep  8 15:44:22 OpenWrt user.info sysinit: Loading includes
Sep  8 15:44:22 OpenWrt user.info sysinit: Optimizing conntrack
Sep  8 15:44:22 OpenWrt user.info sysinit: Loading interfaces
Sep  8 15:44:22 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Sep  8 15:44:25 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sep  8 15:44:25 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: started, version 2.59 cachesize 150
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: compile time options: IPv6 GNU-getopt no-DBus no-i18n DHCP TFTP no-conntrack no-IDN
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq-dhcp[956]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: using local addresses only for domain lan
Sep  8 15:44:29 OpenWrt daemon.warn dnsmasq[956]: no servers found in /tmp/resolv.conf.auto, will retry
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq[956]: read /etc/hosts - 1 addresses
Sep  8 15:44:29 OpenWrt daemon.info dnsmasq-dhcp[956]: read /etc/ethers - 0 addresses
Sep  8 15:44:30 OpenWrt kern.warn kernel: [   41.976000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
Sep  8 15:44:30 OpenWrt kern.warn kernel: [   41.984000] jffs2_build_filesystem(): unlocking the mtd device... done.
Sep  8 15:46:08 OpenWrt kern.warn kernel: [   41.988000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
Sep  8 15:46:08 OpenWrt kern.notice kernel: [  139.712000] JFFS2 notice: (978) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sep  8 15:46:08 OpenWrt auth.err passwd: /etc/passwd: Read-only file system
Sep  8 15:46:08 OpenWrt auth.err passwd: can't update password file /etc/passwd
Sep  8 15:46:08 OpenWrt user.info sysinit: copying files ... done
Sep  8 15:46:10 OpenWrt authpriv.info dropbear[1766]: Running in background
[/spoiler] esto es el system log de luci

[spoiler][    0.000000] Linux version 2.6.39.4 (dani@tool) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #34 Wed Jan 4 22:16:19 CET 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802840e0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 62016k/65536k available (2145k kernel code, 3520k reserved, 368k data, 160k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.064000] MPI_CSBASE_REG(0) = 0x1e000000
[    0.068000] changed ath9k regdomain to 0xff
[    0.072000] registering PCI controller with io_map_base unset
[    0.084000] bio: create slab <bio-0> at 0
[    0.092000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.092000] pci 0000:00:01.0: fixup device configuration
[    0.096000] pci-ath9k-fixup: Writing 0x0029168c to register 0x6000
[    0.100000] pci-ath9k-fixup: Writing 0x02800001 to register 0x6008
[    0.104000] pci-ath9k-fixup: Writing 0x2091168c to register 0x602c
[    0.108000] pci-ath9k-fixup: Writing 0x002a168c to register 0x5000
[    0.112000] pci-ath9k-fixup: Writing 0x02800001 to register 0x5008
[    0.116000] pci-ath9k-fixup: Writing 0x2091168c to register 0x502c
[    0.120000] pci-ath9k-fixup: Writing 0x05040cc0 to register 0x5064
[    0.124000] pci-ath9k-fixup: Writing 0x00033811 to register 0x506c
[    0.128000] pci-ath9k-fixup: Writing 0x0040073b to register 0x4004
[    0.132000] pci-ath9k-fixup: Writing 0x00000003 to register 0x4074
[    0.136000] pci-ath9k-fixup: Writing 0x01c20000 to register 0x4000
[    0.140000] pci-ath9k-fixup: Writing 0x00000044 to register 0x6034
[    0.144000] pci-ath9k-fixup: Device vendor 0x168c, id 0x0029
[    0.148000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.160000] pci 0000:00:01.0: PME# supported from D0 D3hot
[    0.160000] pci 0000:00:01.0: PME# disabled
[    0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.168000] pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x3000ffff] (PCI address [0x30000000-0x3000ffff])
[    0.172000] Switching to clocksource MIPS
[    0.184000] NET: Registered protocol family 2
[    0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.196000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.204000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.212000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.216000] TCP reno registered
[    0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.236000] NET: Registered protocol family 1
[    0.240000] PCI: CLS 0 bytes, default 32
[    0.240000] audit: initializing netlink socket (disabled)
[    0.248000] type=2000 audit(0.248:1): initialized
[    0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.260000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.272000] msgmni has been set to 121
[    0.276000] io scheduler noop registered
[    0.280000] io scheduler deadline registered (default)
[    0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.292000] console [ttyS0] enabled, bootconsole disabled
[    0.308000] bcm963xx-flash bcm963xx-flash.0: 0x02000000 at 0x1e000000
[    0.316000] Number of erase regions: 2
[    0.320000] Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
[    0.328000] Primary Algorithm Table at 0040
[    0.332000] Alternative Vendor Command Set: 0000 (None)
[    0.336000] No Alternate Algorithm Table
[    0.340000] Vcc Minimum:  3.0 V
[    0.344000] Vcc Maximum:  3.6 V
[    0.348000] No Vpp line
[    0.348000] Typical byte/word write timeout: 16 µs
[    0.356000] Maximum byte/word write timeout: 512 µs
[    0.360000] Full buffer write not supported
[    0.364000] Typical block erase timeout: 1024 ms
[    0.368000] Maximum block erase timeout: 16384 ms
[    0.372000] Chip erase not supported
[    0.376000] Device size: 0x1000000 bytes (16 MiB)
[    0.380000] Flash Device Interface description: 0x0002
[    0.388000]   - supports x8 and x16 via BYTE# with asynchronous interface
[    0.392000] Max. bytes in buffer write: 0x1
[    0.400000] Number of Erase Block Regions: 2
[    0.404000]   Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
[    0.408000]   Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
[    0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
[    0.424000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
[    0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.432000]   Amd/Fujitsu Extended Query version 1.3.
[    0.436000]   Silicon revision: 0
[    0.440000]   Address sensitive unlock: Required
[    0.444000]   Erase Suspend: Read/write
[    0.448000]   Block protection: 4 sectors per group
[    0.452000]   Temporary block unprotect: Supported
[    0.460000]   Block protect/unprotect scheme: 4
[    0.464000]   Number of simultaneous operations: 0
[    0.468000]   Burst mode: Not supported
[    0.472000]   Page mode: Not supported
[    0.476000]   Vpp Supply Minimum Program/Erase Voltage: 10.5 V
[    0.480000]   Vpp Supply Maximum Program/Erase Voltage: 11.5 V
[    0.488000]   Top/Bottom Boot Block: Bottom boot
[    0.492000] number of CFI chips: 1
[    0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
[    0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
[    0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
[    0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
[    0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
[    0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
[    0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
[    0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
[    0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
[    0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
[    0.568000] Creating 6 MTD partitions on "bcm963xx":
[    0.576000] 0x000000000000-0x000000020000 : "CFE"
[    0.584000] 0x000000020100-0x000000100000 : "kernel"
[    0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.604000] 0x000000100000-0x000000e00000 : "rootfs"
[    0.612000] mtd: partition "rootfs" set to be root filesystem
[    0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[    0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
[    0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
[    0.648000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.656000] 0x000000020000-0x000000e00000 : "linux"
[    0.672000] bcm63xx-wdt bcm63xx-wdt.0:  started, timer margin: 30 sec
[    0.680000] Registered led device: message
[    0.680000] Registered led device: hspa
[    0.680000] Registered led device: dsl
[    0.680000] Registered led device: power
[    0.680000] Registered led device: all_leds
[    0.684000] TCP westwood registered
[    0.688000] NET: Registered protocol family 17
[    0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    0.700000] All bugs added by David S. Miller <davem@redhat.com>
[    0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.724000] Freeing unused kernel memory: 160k freed
[    3.584000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.656000] There is already a switch registered on the device 'eth0'
[   12.672000] Compat-wireless backport release: compat-wireless-2011-11-29
[   12.680000] Backport based on wireless-testing.git master-2011-12-01
[   12.904000] cfg80211: Calling CRDA to update world regulatory domain
[   13.760000] cfg80211: World regulatory domain updated:
[   13.764000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.772000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.780000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.792000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.800000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.808000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.452000] SCSI subsystem initialized
[   14.552000] There is already a switch registered on the device 'eth0'
[   14.952000] usbcore: registered new interface driver usbfs
[   14.956000] usbcore: registered new interface driver hub
[   14.968000] usbcore: registered new device driver usb
[   16.552000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   16.560000] board_bcm963xx: Setting device platform data
[   16.576000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   16.580000] ath: random mac address will be used: 22:9f:90:3e:7a:be
[   16.588000] ath: EEPROM regdomain: 0xff
[   16.588000] ath: EEPROM indicates we should expect a direct regpair map
[   16.588000] ath: Country alpha2 being used: JP
[   16.588000] ath: Regpair used: 0xff
[   16.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   16.600000] Registered led device: ath9k-phy0
[   16.600000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[   16.612000] cfg80211: Calling CRDA for country: JP
[   16.776000] cfg80211: Regulatory domain changed to country: JP
[   16.784000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   16.792000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.800000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.808000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   16.816000] cfg80211:     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.824000] cfg80211:     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.832000] cfg80211:     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.840000] cfg80211:     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.848000] cfg80211:     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.856000] cfg80211:     (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   16.864000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.872000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   16.880000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   16.916000] Button Hotplug driver version 0.4.1
[   17.892000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   18.444000] PPP generic driver version 2.4.2
[   18.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.996000] NET: Registered protocol family 24
[   19.248000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   19.252000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   19.260000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   19.292000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   19.308000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   19.316000] hub 1-0:1.0: USB hub found
[   19.320000] hub 1-0:1.0: 2 ports detected
[   19.640000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
[   19.756000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
[   20.140000] hub 1-1:1.0: USB hub found
[   20.152000] hub 1-1:1.0: 2 ports detected
[   20.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   20.568000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   20.576000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   20.584000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   20.648000] hub 2-0:1.0: USB hub found
[   20.652000] hub 2-0:1.0: 1 port detected
[   20.932000] Initializing USB Mass Storage driver...
[   20.940000] usbcore: registered new interface driver usb-storage
[   20.944000] USB Mass Storage support registered.
[   21.156000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[   23.808000] eth0: link forced UP - 100/full - flow control off/off
[   24.220000] device eth0 entered promiscuous mode
[   24.320000] br-lan: port 1(eth0) entering forwarding state
[   24.328000] br-lan: port 1(eth0) entering forwarding state
[   41.976000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   41.984000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   41.988000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  139.712000] JFFS2 notice: (978) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler] esto es el kernel log de luci


Intenta con este firmware:
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32706_master_erasesize_bcmtag2.bin

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #442 en: 15-07-2012, 18:58 (Domingo) »
no aun no

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #443 en: 15-07-2012, 19:58 (Domingo) »
no aun no
Estás usando un firmware antiguo de danitool. Con el último firmware de danitool te funciona?

http://www.mediafire.com/download.php?p9duu3gpubg1bdx

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #444 en: 15-07-2012, 20:18 (Domingo) »
Con el último firmware de danitool funciona perfectamente

Citar
http://www.mediafire.com/download.php?p9duu3gpubg1bdx

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #445 en: 15-07-2012, 20:22 (Domingo) »
Con el último firmware de danitool funciona perfectamente

Citar
http://www.mediafire.com/download.php?p9duu3gpubg1bdx
Estoy compilando otro firmware. Creo que está entrando en el panic de la detección cuando no debería y yo sin enterarme :$...

Saludos.

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #446 en: 15-07-2012, 20:31 (Domingo) »
Con el último firmware de danitool funciona perfectamente

Citar
http://www.mediafire.com/download.php?p9duu3gpubg1bdx
Estoy compilando otro firmware. Creo que está entrando en el panic de la detección cuando no debería y yo sin enterarme :$...

Saludos.
Aquí tienes el firmware:
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32706_panic.bin

Saludos!

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #447 en: 15-07-2012, 21:08 (Domingo) »
con este ultimo firmware el bootlog a cambiado pero aun no hay ping

[spoiler]
Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.

@w45260: Flash Manufacture id :c2

@w45260Flash Device id :227a

@w45260flipCFIGeometry:0
Parallel flash device: name MX29LV128DB, id 0x227a, size 16384KB
*** GetHG556aBoardVersion = <0> ***

CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
Total memory: 67108864 bytes (64MB)

Total memory used by CFE:  0x80401000 - 0x8052A510 (1217808)
Initialized Data:          0x8041F3C0 - 0x80421B60 (10144)
BSS Area:                  0x80421B60 - 0x80428510 (27056)
Local Heap:                0x80428510 - 0x80528510 (1048576)
Stack Area:                0x80528510 - 0x8052A510 (8192)
Text (code) segment:       0x80401000 - 0x8041F3B4 (123828)
Boot area (physical):      0x0052B000 - 0x0056B000
Relocation Factor:         I:00000000 - D:00000000

*** GetHG556aBoardVersion = <0> ***

Board IP address                  : 192.168.1.1
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id Name                     : HW556
Psi size in KB                    : 64
Number of MAC Addresses (1-32)    : 10
Base MAC Address                  : 64:16:f0:0a:87:2d
Ethernet PHY Type                 : Internal
Memory size in MB                 : 64
CMT Thread Number                 : 1

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
boot kernel from be020100
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201                                            (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Jul 15 20:29:17 CEST 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] Unable to detect HW556 board 0x6416f0.
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                           es: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jff                                           s2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16                                            bytes
[    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserve                                           d, 398k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: invalid calibration data
[    0.200000] audit: initializing netlink socket (disabled)
[    0.208000] type=2000 audit(0.208:1): initialized
[    0.212000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.220000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY                                           ) (c) 2001-2006 Red Hat, Inc.
[    0.232000] msgmni has been set to 120
[    0.236000] io scheduler noop registered
[    0.240000] io scheduler deadline registered (default)
[    0.248000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_                                           uart
[    0.256000] console [ttyS0] enabled, bootconsole disabled
[    0.256000] console [ttyS0] enabled, bootconsole disabled
[    0.272000] physmap platform flash device: 02000000 at 1e000000
[    0.280000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manuf                                           acturer ID 0x0000c2 Chip ID 0x00227a
[    0.288000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.296000]   Amd/Fujitsu Extended Query version 1.3.
[    0.300000] number of CFI chips: 1
[    0.304000] bcm63xxpart: CFE boot tag found with version 8 and board type HW5                                           56
[    0.312000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.324000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce000                                           0
[    0.332000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 200                                           00
[    0.340000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.348000] bcm63xxpart: Partition 5 is linux offset 20000 and length de0000
[    0.356000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.368000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.376000] 0x000000000000-0x000000020000 : "CFE"
[    0.384000] 0x000000020100-0x000000120000 : "kernel"
[    0.388000] mtd: partition "kernel" must either start or end on erase block b                                           oundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000e00000 : "rootfs"
[    0.416000] mtd: partition "rootfs" set to be root filesystem
[    0.420000] mtd: partition "rootfs_data" created automatically, ofs=330000, l                                           en=AD0000
[    0.428000] 0x000000330000-0x000000e00000 : "rootfs_data"
[    0.440000] 0x000000e00000-0x000000e20000 : "cal_data"
[    0.448000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.456000] 0x000000020000-0x000000e00000 : "linux"
[    0.476000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.488000] TCP cubic registered
[    0.492000] NET: Registered protocol family 17
[    0.496000] 8021q: 802.1Q VLAN Support v1.8
[    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.520000] Freeing unused kernel memory: 196k freed
awk: /proc/cpuinfo: No such file or directory
[    3.212000] eth0: link forced UP - 100/full - flow control off/off
[    3.428000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.496000] There is already a switch registered on the device 'eth0'
[    5.960000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    9.960000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[    9.964000] Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[    9.976000] empty_blocks 172, bad_blocks 0, c->nr_blocks 173
switching to jffs2
- init -

Please press Enter to activate this console. [   12.960000] Compat-wireless backport release: compat-wireless-2012-07-03-2-3-g7adf66e
[   12.968000] Backport based on wireless-testing.git master-2012-07-06
[   12.976000] compat.git: wireless-testing.git
[   13.040000] cfg80211: Calling CRDA to update world regulatory domain
[   13.044000] cfg80211: World regulatory domain updated:
[   13.052000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.060000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.068000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.076000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.084000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.092000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.536000] NET: Registered protocol family 10
[   13.988000] SCSI subsystem initialized
[   14.080000] There is already a switch registered on the device 'eth0'
[   14.440000] usbcore: registered new interface driver usbfs
[   14.444000] usbcore: registered new interface driver hub
[   14.452000] usbcore: registered new device driver usb
[   15.940000] PPP generic driver version 2.4.2
[   16.328000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.620000] NET: Registered protocol family 24
[   16.816000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   16.928000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   16.932000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   16.968000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   16.984000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   16.992000] hub 1-0:1.0: USB hub found
[   16.996000] hub 1-0:1.0: 2 ports detected
[   17.176000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[   17.560000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   17.696000] hub 1-1:1.0: USB hub found
[   17.708000] hub 1-1:1.0: 2 ports detected
[   18.000000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.416000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.528000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   18.532000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   18.540000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   18.608000] hub 2-0:1.0: USB hub found
[   18.612000] hub 2-0:1.0: 1 port detected
[   18.788000] Initializing USB Mass Storage driver...
[   18.792000] usbcore: registered new interface driver usb-storage
[   18.800000] USB Mass Storage support registered.
[   18.836000] usbcore: registered new interface driver ums-alauda
[   18.872000] usbcore: registered new interface driver ums-cypress
[   18.912000] usbcore: registered new interface driver ums-datafab
[   18.948000] usbcore: registered new interface driver ums-freecom
[   18.984000] usbcore: registered new interface driver ums-isd200
[   19.024000] usbcore: registered new interface driver ums-jumpshot
[   19.060000] usbcore: registered new interface driver ums-karma
[   19.100000] usbcore: registered new interface driver ums-sddr09
[   19.136000] usbcore: registered new interface driver ums-sddr55
[   19.172000] usbcore: registered new interface driver ums-usbat
[   19.212000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0

[/spoiler] boolog

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4604
Re: OpenWRT en Huawei hg556a
« Respuesta #448 en: 15-07-2012, 21:39 (Domingo) »
No tengo nada nuevo a añadir a lo dicho en mi último mensaje: con la última compilación que le instalé y con relayd el 'modo cliente transparente' va como un 'cañón'. Después de dos días de prueba parece totalmente estable.

Noltari, te vamos a tener que hacer un 'monumento' por tu tenacidad para resolver los problemas que se están presentando con este router (diferentes chipsets wifi, varios tipos de memorias, etc.)  >:( >:(
Valoraciones positivas en compra/venta:
175 en Htcmania
240 en Har2mano
12 en gsmspain
 ....
 
Mis equipos en venta: https://drive.google.com/open?id=1Zi_bqLSfg_qCT8sx6JhPaWVvSeZXpcka

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #449 en: 15-07-2012, 21:42 (Domingo) »
Este firmware debería ser compatible con todos los modelos de HG556a.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32738.bin

He actualizado los parches SVN: https://dl.dropbox.com/u/4708147/openwrt/hw556/hw556_svn_all.patch
Eeprom que también hay que añadir al SVN: https://dl.dropbox.com/u/4708147/openwrt/hw556/rt3062_eeprom.zip

Espero feedback de todos :3!

Saludos!

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #450 en: 15-07-2012, 22:09 (Domingo) »
me gustaría decir que funciona, pero para mi ruter aun no.

el ultimo firmware:

Citar
Insertar Cita
Este firmware debería ser compatible con todos los modelos de HG556a.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32738.bin

da el siguiente bootlog

[spoiler]Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id Name                     : HW556
Psi size in KB                    : 64
Number of MAC Addresses (1-32)    : 10
Base MAC Address                  : 64:16:f0:0a:87:2d
Ethernet PHY Type                 : Internal
Memory size in MB                 : 64
CMT Thread Number                 : 1

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
boot kernel from be020100
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Jul 15 21:34:58 CEST 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
[    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
[    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=C30000
[    0.432000] 0x000000330000-0x000000f60000 : "rootfs_data"
[    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000f60000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.492000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.500000] 8021q: 802.1Q VLAN Support v1.8
[    0.516000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 196k freed
awk: /proc/cpuinfo: No such file or directory
[    3.268000] eth0: link forced UP - 100/full - flow control off/off
[    3.488000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.552000] There is already a switch registered on the device 'eth0'
[    6.020000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    9.996000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   10.004000] Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[   10.012000] empty_blocks 194, bad_blocks 0, c->nr_blocks 195
switching to jffs2
- init -

Please press Enter to activate this console. [   13.004000] Compat-wireless backport release: compat-wireless-2012-07-03-2-3-g7adf66e
[   13.012000] Backport based on wireless-testing.git master-2012-07-06
[   13.020000] compat.git: wireless-testing.git
[   13.088000] cfg80211: Calling CRDA to update world regulatory domain
[   13.092000] cfg80211: World regulatory domain updated:
[   13.100000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.108000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.116000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.124000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.132000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.140000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.580000] NET: Registered protocol family 10
[   14.036000] SCSI subsystem initialized
[   14.128000] There is already a switch registered on the device 'eth0'
[   14.488000] usbcore: registered new interface driver usbfs
[   14.492000] usbcore: registered new interface driver hub
[   14.500000] usbcore: registered new device driver usb
[   15.616000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.632000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   15.640000] ath: phy0: random mac address will be used: 16:a7:6d:d2:11:93
[   15.660000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0320000, irq=39
[   15.672000] cfg80211: Calling CRDA for country: US
[   15.676000] cfg80211: Regulatory domain changed to country: US
[   15.680000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   15.688000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   15.696000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   15.704000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.712000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.720000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.728000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   16.152000] PPP generic driver version 2.4.2
[   16.544000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.836000] NET: Registered protocol family 24
[   17.032000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.144000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   17.148000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   17.184000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   17.200000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   17.208000] hub 1-0:1.0: USB hub found
[   17.212000] hub 1-0:1.0: 2 ports detected
[   17.392000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[   17.776000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   17.916000] hub 1-1:1.0: USB hub found
[   17.928000] hub 1-1:1.0: 2 ports detected
[   18.220000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.636000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.748000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   18.752000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   18.760000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   18.828000] hub 2-0:1.0: USB hub found
[   18.832000] hub 2-0:1.0: 1 port detected
[   19.008000] Initializing USB Mass Storage driver...
[   19.012000] usbcore: registered new interface driver usb-storage
[   19.016000] USB Mass Storage support registered.
[   19.056000] usbcore: registered new interface driver ums-alauda
[   19.092000] usbcore: registered new interface driver ums-cypress
[   19.132000] usbcore: registered new interface driver ums-datafab
[   19.168000] usbcore: registered new interface driver ums-freecom
[   19.204000] usbcore: registered new interface driver ums-isd200
[   19.244000] usbcore: registered new interface driver ums-jumpshot
[   19.280000] usbcore: registered new interface driver ums-karma
[   19.320000] usbcore: registered new interface driver ums-sddr09
[   19.356000] usbcore: registered new interface driver ums-sddr55
[   19.392000] usbcore: registered new interface driver ums-usbat
[   19.432000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0[/spoiler] pero nada de ping

muchas gracias por tu trabajo

saludos.

raphik

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #451 en: 15-07-2012, 22:25 (Domingo) »
Este firmware debería ser compatible con todos los modelos de HG556a.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32738.bin
...
Espero feedback de todos :3!

En mi router sí funciona. Te he enviado el bootlog, aunque supongo que a estas altura ya no te hará ninguna falta.

Saludos.

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #452 en: 15-07-2012, 22:48 (Domingo) »
me gustaría decir que funciona, pero para mi ruter aun no.

el ultimo firmware:

Citar
Insertar Cita
Este firmware debería ser compatible con todos los modelos de HG556a.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32738.bin

da el siguiente bootlog

[spoiler]Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id Name                     : HW556
Psi size in KB                    : 64
Number of MAC Addresses (1-32)    : 10
Base MAC Address                  : 64:16:f0:0a:87:2d
Ethernet PHY Type                 : Internal
Memory size in MB                 : 64
CMT Thread Number                 : 1

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
boot kernel from be020100
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Jul 15 21:34:58 CEST 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
[    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
[    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=C30000
[    0.432000] 0x000000330000-0x000000f60000 : "rootfs_data"
[    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000f60000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.492000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.500000] 8021q: 802.1Q VLAN Support v1.8
[    0.516000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 196k freed
awk: /proc/cpuinfo: No such file or directory
[    3.268000] eth0: link forced UP - 100/full - flow control off/off
[    3.488000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.552000] There is already a switch registered on the device 'eth0'
[    6.020000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    9.996000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   10.004000] Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[   10.012000] empty_blocks 194, bad_blocks 0, c->nr_blocks 195
switching to jffs2
- init -

Please press Enter to activate this console. [   13.004000] Compat-wireless backport release: compat-wireless-2012-07-03-2-3-g7adf66e
[   13.012000] Backport based on wireless-testing.git master-2012-07-06
[   13.020000] compat.git: wireless-testing.git
[   13.088000] cfg80211: Calling CRDA to update world regulatory domain
[   13.092000] cfg80211: World regulatory domain updated:
[   13.100000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.108000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.116000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.124000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.132000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.140000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.580000] NET: Registered protocol family 10
[   14.036000] SCSI subsystem initialized
[   14.128000] There is already a switch registered on the device 'eth0'
[   14.488000] usbcore: registered new interface driver usbfs
[   14.492000] usbcore: registered new interface driver hub
[   14.500000] usbcore: registered new device driver usb
[   15.616000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.632000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   15.640000] ath: phy0: random mac address will be used: 16:a7:6d:d2:11:93
[   15.660000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc0320000, irq=39
[   15.672000] cfg80211: Calling CRDA for country: US
[   15.676000] cfg80211: Regulatory domain changed to country: US
[   15.680000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   15.688000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   15.696000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   15.704000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.712000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.720000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.728000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   16.152000] PPP generic driver version 2.4.2
[   16.544000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.836000] NET: Registered protocol family 24
[   17.032000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.144000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   17.148000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   17.184000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   17.200000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   17.208000] hub 1-0:1.0: USB hub found
[   17.212000] hub 1-0:1.0: 2 ports detected
[   17.392000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[   17.776000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   17.916000] hub 1-1:1.0: USB hub found
[   17.928000] hub 1-1:1.0: 2 ports detected
[   18.220000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.636000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.748000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   18.752000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   18.760000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   18.828000] hub 2-0:1.0: USB hub found
[   18.832000] hub 2-0:1.0: 1 port detected
[   19.008000] Initializing USB Mass Storage driver...
[   19.012000] usbcore: registered new interface driver usb-storage
[   19.016000] USB Mass Storage support registered.
[   19.056000] usbcore: registered new interface driver ums-alauda
[   19.092000] usbcore: registered new interface driver ums-cypress
[   19.132000] usbcore: registered new interface driver ums-datafab
[   19.168000] usbcore: registered new interface driver ums-freecom
[   19.204000] usbcore: registered new interface driver ums-isd200
[   19.244000] usbcore: registered new interface driver ums-jumpshot
[   19.280000] usbcore: registered new interface driver ums-karma
[   19.320000] usbcore: registered new interface driver ums-sddr09
[   19.356000] usbcore: registered new interface driver ums-sddr55
[   19.392000] usbcore: registered new interface driver ums-usbat
[   19.432000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0[/spoiler] pero nada de ping

muchas gracias por tu trabajo

saludos.

¿Lo estás flasheando desde el bootloader? (lo digo porque desde el bootloader se pone la configuración del firmware por defecto)

El firmware, de acuerdo con el bootlog que has colgado debería funcionar perfectamente. ¿Estás seguro de que no tiene nada que ver con la configuración TCP/IP de tu PC?

Saludos.

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #453 en: 15-07-2012, 22:50 (Domingo) »
Este firmware debería ser compatible con todos los modelos de HG556a.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32738.bin
...
Espero feedback de todos :3!

En mi router sí funciona. Te he enviado el bootlog, aunque supongo que a estas altura ya no te hará ninguna falta.

Saludos.
Te estaba compilando uno especial para mpd mientras cenaba. 6MB de firmware xDDD.
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32738_mpd.bin

El firmware es idéntico al anterior, con los paquetes necesarios para seguir el tutorial del colega raphik:
https://foro.seguridadwireless.net/openwrt/tutorial-music-player-daemon-en-hg556a/

Saludos!

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #454 en: 15-07-2012, 23:01 (Domingo) »
Citar
¿Lo estás flasheando desde el bootloader? (lo digo porque desde el bootloader se pone la configuración del firmware por defecto)

El firmware, de acuerdo con el bootlog que has colgado debería funcionar perfectamente. ¿Estás seguro de que no tiene nada que ver con la configuración TCP/IP de tu PC?

no, lo flasheo por el explorador, y las ip que tengo son las mismas que uso para poner la firmware de danitool.

ip 192.168.1.100
mask 255.255.255.0
puerta 192.168.1.1

pero en el bootlog se ve que queda parado antes de arrancar la red, en este punto

[   19.432000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0


Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #455 en: 15-07-2012, 23:09 (Domingo) »
Para mi que te está fallando la configuración de openwrt si lo estás flasheando a través de luci desde el firmware de danitool.

Desde la consola del bootlog pulsa enter cuando ya no salga más información por pantalla y te aparecerá una consola de comandos (en mi firmware).
Ejecuta el siguiente comando que borrará la configuración y reiniciará el router:
Código: [Seleccionar]
mtd -r erase rootfs_data
EDIT: Otra opción es que enciendas el router pulsando el botón reset y no lo sueltes hasta pasados unos 20 segundos. Después, vas en el navegador a la url http://192.168.1.1/ y te aparecerá un formulario para cargar el firmware.

Saludos.
« Última modificación: 15-07-2012, 23:12 (Domingo) por Noltari »

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #456 en: 16-07-2012, 00:04 (Lunes) »
BINGO!! ahora funciono perfectamente gracias al código que me diste, muchas gracias por tu trabajo, eres un genio.

la manera que me sugieres que ponga el firmware, es la que utilizo siempre, lo único diferente, a sido el código de borrado de la configuración del firmware.

pero si no hay conexión serie, como se se puede borrar la configuración del firmware?

muchísimas gracias por tu ayuda Noltari.

saludos 

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #457 en: 16-07-2012, 00:10 (Lunes) »
BINGO!! ahora funciono perfectamente gracias al código que me diste, muchas gracias por tu trabajo, eres un genio.

la manera que me sugieres que ponga el firmware, es la que utilizo siempre, lo único diferente, a sido el código de borrado de la configuración del firmware.

pero si no hay conexión serie, como se se puede borrar la configuración del firmware?

muchísimas gracias por tu ayuda Noltari.

saludos 
Hay un checkbox al actualizar vía luci justo debajo del formulario de seleción del archivo del firmware que activa/desactiva el borrado de la configuración.

Pues nada, esto está hecho chavales, ya tenemos un único firmware funcional en todos los HG556a.
Gracias a todos los que lo habéis hecho posible y en especial a danitool por el código en el que nos hemos basado y a gmtii por su contribución a los ralink. Y gracias también a todos los que habéis ayudado con las pruebas :D.

Por cierto, voy a esperar a que me acepten cuatro parches que tengo pendientes para enviar los parches de este router, que si no va a ser un jaleo curioso...

Saludos!

Chumpy

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #458 en: 16-07-2012, 00:31 (Lunes) »
Noltari, podías indicar que incluye el último firm?, para que ya quede todo clarito clarito.

Muchas gracias por tu trabajo y el de todos los que han colaborado.

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #459 en: 16-07-2012, 00:32 (Lunes) »
Noltari, podías indicar que incluye el último firm?, para que ya quede todo clarito clarito.

Muchas gracias por tu trabajo y el de todos los que han colaborado.
https://foro.seguridadwireless.net/openwrt/openwrt-en-huaweig-hg556a/msg247502/#msg247502