Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a  (Leído 1893028 veces)

0 Usuarios y 4 Visitantes están viendo este tema.

Ggarza

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #500 en: 19-07-2012, 16:01 (Jueves) »
Jaja tienes toda la razon.

Pues despues de ejecutar el comando da:

256+0 records in
256+0 records out

despues de esto un iwconfig a traves del ssh da:

lo          no wireless extensions
eth0      no wireless extensions
br-lan     no wireless extensions



Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #501 en: 19-07-2012, 16:12 (Jueves) »
Jaja tienes toda la razon.

Pues despues de ejecutar el comando da:

256+0 records in
256+0 records out

despues de esto un iwconfig a traves del ssh da:

lo          no wireless extensions
eth0      no wireless extensions
br-lan     no wireless extensions
Tienes que reiniciar el router.

Ponme un bootlog del router después de reiniciar:
dmesg > /www/dmesg.txt
En el PC:
http://192.168.1.1/dmesg.txt

Saludos
« Última modificación: 19-07-2012, 16:17 (Jueves) por Noltari »

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #502 en: 19-07-2012, 16:16 (Jueves) »
emeryth necesito un bootlog del router que dices que te has cargado el caldata para saber qué archivo tengo que pasarte para restaurarlo.

Saludos.

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #503 en: 19-07-2012, 16:28 (Jueves) »
Citar
emeryth y Ggarza, probad a restaurar estos datos con mi último firmware (El primero que aparece en el primer post).

https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_MX29GL128EH.bin

Podéis pasarlos al router de varias formas:
1) Por USB.
2) Conectándolo a otro router que tenga internet y ejecutando el comando:
wget https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_MX29GL128EH.bin
3) Usando netcat
4) etc.

Para restaurarlos ejecutad:
dd if=ath_MX29GL128EH.bin of=/dev/mtd4

Saludos.

hola Noltari, pensé que el anterior ath_data.bin era para mi router, pero no funciona (no aparece el wifi), pero si pude instalar el tu ultimo firmware.

[spoiler][    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Jul 17 19:59:50 CEST 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.200000] PCI: CLS 0 bytes, default 16
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
[    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
[    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=C20000
[    0.432000] 0x000000340000-0x000000f60000 : "rootfs_data"
[    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000f60000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.488000] Registered led device: HW556:red:message
[    0.488000] Registered led device: HW556:red:hspa
[    0.492000] Registered led device: HW556:red:dsl
[    0.492000] Registered led device: HW556:red:power
[    0.492000] Registered led device: HW556:red:all
[    0.492000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.500000] 8021q: 802.1Q VLAN Support v1.8
[    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 196k freed
[    3.252000] eth0: link forced UP - 100/full - flow control off/off
[    3.468000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.536000] There is already a switch registered on the device 'eth0'
[    6.004000] Button Hotplug driver version 0.4.1
[   10.000000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[   12.984000] Compat-wireless backport release: compat-wireless-2012-07-13
[   12.992000] Backport based on wireless-testing.git master-2012-07-16
[   13.000000] compat.git: wireless-testing.git
[   13.068000] cfg80211: Calling CRDA to update world regulatory domain
[   13.072000] cfg80211: World regulatory domain updated:
[   13.080000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.088000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.096000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.104000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.112000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.120000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.564000] NET: Registered protocol family 10
[   14.020000] SCSI subsystem initialized
[   14.112000] There is already a switch registered on the device 'eth0'
[   14.468000] usbcore: registered new interface driver usbfs
[   14.476000] usbcore: registered new interface driver hub
[   14.484000] usbcore: registered new device driver usb
[   15.600000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.616000] ath: phy0: Bad EEPROM checksum 0x910 or revision 0x0006
[   15.620000] ath: phy0: Unable to initialize hardware; initialization status: -22
[   15.628000] ath9k 0000:00:01.0: Failed to initialize device
[   15.636000] ath9k: probe of 0000:00:01.0 failed with error -22
[   16.012000] PPP generic driver version 2.4.2
[   16.404000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.696000] NET: Registered protocol family 24
[   16.896000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.004000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   17.008000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   17.044000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   17.060000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   17.068000] hub 1-0:1.0: USB hub found
[   17.072000] hub 1-0:1.0: 2 ports detected
[   17.252000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[   17.636000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   17.776000] hub 1-1:1.0: USB hub found
[   17.788000] hub 1-1:1.0: 2 ports detected
[   18.076000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.604000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   18.608000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   18.616000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   18.684000] hub 2-0:1.0: USB hub found
[   18.688000] hub 2-0:1.0: 1 port detected
[   18.864000] Initializing USB Mass Storage driver...
[   18.868000] usbcore: registered new interface driver usb-storage
[   18.876000] USB Mass Storage support registered.
[   18.912000] usbcore: registered new interface driver ums-alauda
[   18.948000] usbcore: registered new interface driver ums-cypress
[   18.984000] usbcore: registered new interface driver ums-datafab
[   19.024000] usbcore: registered new interface driver ums-freecom
[   19.060000] usbcore: registered new interface driver ums-isd200
[   19.096000] usbcore: registered new interface driver ums-jumpshot
[   19.136000] usbcore: registered new interface driver ums-karma
[   19.172000] usbcore: registered new interface driver ums-sddr09
[   19.212000] usbcore: registered new interface driver ums-sddr55
[   19.248000] usbcore: registered new interface driver ums-usbat
[   19.288000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   24.516000] eth0: link forced UP - 100/full - flow control off/off
[   24.532000] device eth0 entered promiscuous mode
[   24.540000] br-lan: port 1(eth0) entered forwarding state
[   24.544000] br-lan: port 1(eth0) entered forwarding state
[   26.548000] br-lan: port 1(eth0) entered forwarding state
[/spoiler] kernel log

[spoiler]Jul 19 14:18:08 OpenWrt kern.warn kernel: [    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Jul 19 14:18:08 OpenWrt kern.warn kernel: [    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.000000] NR_IRQS:128
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.036000] pid_max: default: 32768 minimum: 301
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.040000] Mount-cache hash table entries: 512
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.052000] NET: Registered protocol family 16
Jul 19 14:18:08 OpenWrt kern.warn kernel: [    0.068000] registering PCI controller with io_map_base unset
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.088000] bio: create slab <bio-0> at 0
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.096000] PCI host bridge to bus 0000:00
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.124000] Switching to clocksource MIPS
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.136000] NET: Registered protocol family 2
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.172000] TCP reno registered
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.188000] NET: Registered protocol family 1
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.192000] pci 0000:00:01.0: fixup device configuration
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.200000] PCI: CLS 0 bytes, default 16
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.204000] audit: initializing netlink socket (disabled)
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.212000] type=2000 audit(0.212:1): initialized
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.236000] msgmni has been set to 120
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.240000] io scheduler noop registered
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.244000] io scheduler deadline registered (default)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.260000] console [ttyS0] enabled, bootconsole disabled
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.276000] physmap platform flash device: 02000000 at 1e000000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.300000]   Amd/Fujitsu Extended Query version 1.3.
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.304000] number of CFI chips: 1
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.420000] mtd: partition "rootfs" set to be root filesystem
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.424000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=C20000
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.432000] 0x000000340000-0x000000f60000 : "rootfs_data"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.460000] 0x000000020000-0x000000f60000 : "linux"
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.488000] Registered led device: HW556:red:message
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.488000] Registered led device: HW556:red:hspa
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: HW556:red:dsl
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: HW556:red:power
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: HW556:red:all
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.492000] TCP cubic registered
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.496000] NET: Registered protocol family 17
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.500000] 8021q: 802.1Q VLAN Support v1.8
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.524000] Freeing unused kernel memory: 196k freed
Jul 19 14:18:08 OpenWrt kern.info kernel: [    3.252000] eth0: link forced UP - 100/full - flow control off/off
Jul 19 14:18:08 OpenWrt kern.info kernel: [    3.468000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
Jul 19 14:18:08 OpenWrt kern.warn kernel: [    4.536000] There is already a switch registered on the device 'eth0'
Jul 19 14:18:08 OpenWrt kern.info kernel: [    6.004000] Button Hotplug driver version 0.4.1
Jul 19 14:18:08 OpenWrt kern.notice kernel: [   10.000000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
Jul 19 14:18:08 OpenWrt kern.info kernel: [   12.984000] Compat-wireless backport release: compat-wireless-2012-07-13
Jul 19 14:18:08 OpenWrt kern.info kernel: [   12.992000] Backport based on wireless-testing.git master-2012-07-16
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.000000] compat.git: wireless-testing.git
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.068000] cfg80211: Calling CRDA to update world regulatory domain
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.072000] cfg80211: World regulatory domain updated:
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.096000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.104000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.112000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.120000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.564000] NET: Registered protocol family 10
Jul 19 14:18:08 OpenWrt kern.notice kernel: [   14.020000] SCSI subsystem initialized
Jul 19 14:18:08 OpenWrt kern.warn kernel: [   14.112000] There is already a switch registered on the device 'eth0'
Jul 19 14:18:08 OpenWrt kern.info kernel: [   14.468000] usbcore: registered new interface driver usbfs
Jul 19 14:18:09 OpenWrt kern.info kernel: [   14.476000] usbcore: registered new interface driver hub
Jul 19 14:18:09 OpenWrt kern.info kernel: [   14.484000] usbcore: registered new device driver usb
Jul 19 14:18:09 OpenWrt kern.warn kernel: [   15.600000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Jul 19 14:18:09 OpenWrt kern.err kernel: [   15.616000] ath: phy0: Bad EEPROM checksum 0x910 or revision 0x0006
Jul 19 14:18:09 OpenWrt kern.err kernel: [   15.620000] ath: phy0: Unable to initialize hardware; initialization status: -22
Jul 19 14:18:09 OpenWrt kern.err kernel: [   15.628000] ath9k 0000:00:01.0: Failed to initialize device
Jul 19 14:18:09 OpenWrt kern.warn kernel: [   15.636000] ath9k: probe of 0000:00:01.0 failed with error -22
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.012000] PPP generic driver version 2.4.2
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.404000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.696000] NET: Registered protocol family 24
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.896000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.068000] hub 1-0:1.0: USB hub found
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.072000] hub 1-0:1.0: 2 ports detected
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.252000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.636000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.776000] hub 1-1:1.0: USB hub found
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.788000] hub 1-1:1.0: 2 ports detected
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.076000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.492000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.604000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.608000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.616000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.684000] hub 2-0:1.0: USB hub found
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.688000] hub 2-0:1.0: 1 port detected
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.864000] Initializing USB Mass Storage driver...
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.868000] usbcore: registered new interface driver usb-storage
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.876000] USB Mass Storage support registered.
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.912000] usbcore: registered new interface driver ums-alauda
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.948000] usbcore: registered new interface driver ums-cypress
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.984000] usbcore: registered new interface driver ums-datafab
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.024000] usbcore: registered new interface driver ums-freecom
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.060000] usbcore: registered new interface driver ums-isd200
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.096000] usbcore: registered new interface driver ums-jumpshot
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.136000] usbcore: registered new interface driver ums-karma
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.172000] usbcore: registered new interface driver ums-sddr09
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.212000] usbcore: registered new interface driver ums-sddr55
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.248000] usbcore: registered new interface driver ums-usbat
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.288000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.516000] eth0: link forced UP - 100/full - flow control off/off
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.532000] device eth0 entered promiscuous mode
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.540000] br-lan: port 1(eth0) entered forwarding state
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.544000] br-lan: port 1(eth0) entered forwarding state
Jul 19 14:18:12 OpenWrt daemon.notice netifd: Interface 'lan' is now up
Jul 19 14:18:12 OpenWrt daemon.notice netifd: Interface 'loopback' is now up
Jul 19 14:18:14 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Jul 19 14:18:14 OpenWrt kern.info kernel: [   26.548000] br-lan: port 1(eth0) entered forwarding state
Jul 19 14:18:17 OpenWrt user.info sysinit: Loading defaults
Jul 19 14:18:18 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Jul 19 14:18:18 OpenWrt user.info sysinit: Loading synflood protection
Jul 19 14:18:18 OpenWrt user.info sysinit: Adding custom chains
Jul 19 14:18:19 OpenWrt user.info sysinit: Loading zones
Jul 19 14:18:22 OpenWrt user.info sysinit: Loading forwardings
Jul 19 14:18:22 OpenWrt user.info sysinit: Loading rules
Jul 19 14:18:23 OpenWrt user.info sysinit: Loading redirects
Jul 19 14:18:23 OpenWrt user.info sysinit: Loading includes
Jul 19 14:18:23 OpenWrt user.info sysinit: Optimizing conntrack
Jul 19 14:18:23 OpenWrt user.info sysinit: Loading interfaces
Jul 19 14:18:24 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Jul 19 14:18:26 OpenWrt authpriv.info dropbear[952]: Running in background
Jul 19 14:18:28 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jul 19 14:18:28 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: started, version 2.62 cachesize 150
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using local addresses only for domain lan
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: reading /tmp/resolv.conf.auto
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using nameserver 8.8.8.8#53
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using nameserver 8.8.4.4#53
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using local addresses only for domain lan
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: read /etc/hosts - 1 addresses
[/spoiler] system log

gracias.  ;D

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #504 en: 19-07-2012, 16:42 (Jueves) »
Citar
emeryth y Ggarza, probad a restaurar estos datos con mi último firmware (El primero que aparece en el primer post).

https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_MX29GL128EH.bin

Podéis pasarlos al router de varias formas:
1) Por USB.
2) Conectándolo a otro router que tenga internet y ejecutando el comando:
wget https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_MX29GL128EH.bin
3) Usando netcat
4) etc.

Para restaurarlos ejecutad:
dd if=ath_MX29GL128EH.bin of=/dev/mtd4

Saludos.

hola Noltari, pensé que el anterior ath_data.bin era para mi router, pero no funciona (no aparece el wifi), pero si pude instalar el tu ultimo firmware.

[spoiler][    0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Jul 17 19:59:50 CEST 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.200000] PCI: CLS 0 bytes, default 16
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
[    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
[    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=C20000
[    0.432000] 0x000000340000-0x000000f60000 : "rootfs_data"
[    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000f60000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.488000] Registered led device: HW556:red:message
[    0.488000] Registered led device: HW556:red:hspa
[    0.492000] Registered led device: HW556:red:dsl
[    0.492000] Registered led device: HW556:red:power
[    0.492000] Registered led device: HW556:red:all
[    0.492000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.500000] 8021q: 802.1Q VLAN Support v1.8
[    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 196k freed
[    3.252000] eth0: link forced UP - 100/full - flow control off/off
[    3.468000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.536000] There is already a switch registered on the device 'eth0'
[    6.004000] Button Hotplug driver version 0.4.1
[   10.000000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[   12.984000] Compat-wireless backport release: compat-wireless-2012-07-13
[   12.992000] Backport based on wireless-testing.git master-2012-07-16
[   13.000000] compat.git: wireless-testing.git
[   13.068000] cfg80211: Calling CRDA to update world regulatory domain
[   13.072000] cfg80211: World regulatory domain updated:
[   13.080000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.088000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.096000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.104000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.112000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.120000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.564000] NET: Registered protocol family 10
[   14.020000] SCSI subsystem initialized
[   14.112000] There is already a switch registered on the device 'eth0'
[   14.468000] usbcore: registered new interface driver usbfs
[   14.476000] usbcore: registered new interface driver hub
[   14.484000] usbcore: registered new device driver usb
[   15.600000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.616000] ath: phy0: Bad EEPROM checksum 0x910 or revision 0x0006
[   15.620000] ath: phy0: Unable to initialize hardware; initialization status: -22
[   15.628000] ath9k 0000:00:01.0: Failed to initialize device
[   15.636000] ath9k: probe of 0000:00:01.0 failed with error -22
[   16.012000] PPP generic driver version 2.4.2
[   16.404000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.696000] NET: Registered protocol family 24
[   16.896000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.004000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   17.008000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   17.044000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   17.060000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   17.068000] hub 1-0:1.0: USB hub found
[   17.072000] hub 1-0:1.0: 2 ports detected
[   17.252000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[   17.636000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   17.776000] hub 1-1:1.0: USB hub found
[   17.788000] hub 1-1:1.0: 2 ports detected
[   18.076000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.604000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   18.608000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   18.616000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   18.684000] hub 2-0:1.0: USB hub found
[   18.688000] hub 2-0:1.0: 1 port detected
[   18.864000] Initializing USB Mass Storage driver...
[   18.868000] usbcore: registered new interface driver usb-storage
[   18.876000] USB Mass Storage support registered.
[   18.912000] usbcore: registered new interface driver ums-alauda
[   18.948000] usbcore: registered new interface driver ums-cypress
[   18.984000] usbcore: registered new interface driver ums-datafab
[   19.024000] usbcore: registered new interface driver ums-freecom
[   19.060000] usbcore: registered new interface driver ums-isd200
[   19.096000] usbcore: registered new interface driver ums-jumpshot
[   19.136000] usbcore: registered new interface driver ums-karma
[   19.172000] usbcore: registered new interface driver ums-sddr09
[   19.212000] usbcore: registered new interface driver ums-sddr55
[   19.248000] usbcore: registered new interface driver ums-usbat
[   19.288000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   24.516000] eth0: link forced UP - 100/full - flow control off/off
[   24.532000] device eth0 entered promiscuous mode
[   24.540000] br-lan: port 1(eth0) entered forwarding state
[   24.544000] br-lan: port 1(eth0) entered forwarding state
[   26.548000] br-lan: port 1(eth0) entered forwarding state
[/spoiler] kernel log

[spoiler]Jul 19 14:18:08 OpenWrt kern.warn kernel: [    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Jul 19 14:18:08 OpenWrt kern.warn kernel: [    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.000000] NR_IRQS:128
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.036000] pid_max: default: 32768 minimum: 301
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.040000] Mount-cache hash table entries: 512
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.052000] NET: Registered protocol family 16
Jul 19 14:18:08 OpenWrt kern.warn kernel: [    0.068000] registering PCI controller with io_map_base unset
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.088000] bio: create slab <bio-0> at 0
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.096000] PCI host bridge to bus 0000:00
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.124000] Switching to clocksource MIPS
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.136000] NET: Registered protocol family 2
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.172000] TCP reno registered
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.188000] NET: Registered protocol family 1
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.192000] pci 0000:00:01.0: fixup device configuration
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.200000] PCI: CLS 0 bytes, default 16
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.204000] audit: initializing netlink socket (disabled)
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.212000] type=2000 audit(0.212:1): initialized
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.236000] msgmni has been set to 120
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.240000] io scheduler noop registered
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.244000] io scheduler deadline registered (default)
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.260000] console [ttyS0] enabled, bootconsole disabled
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.276000] physmap platform flash device: 02000000 at 1e000000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.300000]   Amd/Fujitsu Extended Query version 1.3.
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.304000] number of CFI chips: 1
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.420000] mtd: partition "rootfs" set to be root filesystem
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.424000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=C20000
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.432000] 0x000000340000-0x000000f60000 : "rootfs_data"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
Jul 19 14:18:08 OpenWrt kern.notice kernel: [    0.460000] 0x000000020000-0x000000f60000 : "linux"
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.488000] Registered led device: HW556:red:message
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.488000] Registered led device: HW556:red:hspa
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: HW556:red:dsl
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: HW556:red:power
Jul 19 14:18:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: HW556:red:all
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.492000] TCP cubic registered
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.496000] NET: Registered protocol family 17
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.500000] 8021q: 802.1Q VLAN Support v1.8
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Jul 19 14:18:08 OpenWrt kern.info kernel: [    0.524000] Freeing unused kernel memory: 196k freed
Jul 19 14:18:08 OpenWrt kern.info kernel: [    3.252000] eth0: link forced UP - 100/full - flow control off/off
Jul 19 14:18:08 OpenWrt kern.info kernel: [    3.468000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
Jul 19 14:18:08 OpenWrt kern.warn kernel: [    4.536000] There is already a switch registered on the device 'eth0'
Jul 19 14:18:08 OpenWrt kern.info kernel: [    6.004000] Button Hotplug driver version 0.4.1
Jul 19 14:18:08 OpenWrt kern.notice kernel: [   10.000000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
Jul 19 14:18:08 OpenWrt kern.info kernel: [   12.984000] Compat-wireless backport release: compat-wireless-2012-07-13
Jul 19 14:18:08 OpenWrt kern.info kernel: [   12.992000] Backport based on wireless-testing.git master-2012-07-16
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.000000] compat.git: wireless-testing.git
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.068000] cfg80211: Calling CRDA to update world regulatory domain
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.072000] cfg80211: World regulatory domain updated:
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.096000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.104000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.112000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.120000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 19 14:18:08 OpenWrt kern.info kernel: [   13.564000] NET: Registered protocol family 10
Jul 19 14:18:08 OpenWrt kern.notice kernel: [   14.020000] SCSI subsystem initialized
Jul 19 14:18:08 OpenWrt kern.warn kernel: [   14.112000] There is already a switch registered on the device 'eth0'
Jul 19 14:18:08 OpenWrt kern.info kernel: [   14.468000] usbcore: registered new interface driver usbfs
Jul 19 14:18:09 OpenWrt kern.info kernel: [   14.476000] usbcore: registered new interface driver hub
Jul 19 14:18:09 OpenWrt kern.info kernel: [   14.484000] usbcore: registered new device driver usb
Jul 19 14:18:09 OpenWrt kern.warn kernel: [   15.600000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Jul 19 14:18:09 OpenWrt kern.err kernel: [   15.616000] ath: phy0: Bad EEPROM checksum 0x910 or revision 0x0006
Jul 19 14:18:09 OpenWrt kern.err kernel: [   15.620000] ath: phy0: Unable to initialize hardware; initialization status: -22
Jul 19 14:18:09 OpenWrt kern.err kernel: [   15.628000] ath9k 0000:00:01.0: Failed to initialize device
Jul 19 14:18:09 OpenWrt kern.warn kernel: [   15.636000] ath9k: probe of 0000:00:01.0 failed with error -22
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.012000] PPP generic driver version 2.4.2
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.404000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.696000] NET: Registered protocol family 24
Jul 19 14:18:09 OpenWrt kern.info kernel: [   16.896000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.068000] hub 1-0:1.0: USB hub found
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.072000] hub 1-0:1.0: 2 ports detected
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.252000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.636000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.776000] hub 1-1:1.0: USB hub found
Jul 19 14:18:09 OpenWrt kern.info kernel: [   17.788000] hub 1-1:1.0: 2 ports detected
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.076000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.492000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.604000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.608000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.616000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.684000] hub 2-0:1.0: USB hub found
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.688000] hub 2-0:1.0: 1 port detected
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.864000] Initializing USB Mass Storage driver...
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.868000] usbcore: registered new interface driver usb-storage
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.876000] USB Mass Storage support registered.
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.912000] usbcore: registered new interface driver ums-alauda
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.948000] usbcore: registered new interface driver ums-cypress
Jul 19 14:18:09 OpenWrt kern.info kernel: [   18.984000] usbcore: registered new interface driver ums-datafab
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.024000] usbcore: registered new interface driver ums-freecom
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.060000] usbcore: registered new interface driver ums-isd200
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.096000] usbcore: registered new interface driver ums-jumpshot
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.136000] usbcore: registered new interface driver ums-karma
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.172000] usbcore: registered new interface driver ums-sddr09
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.212000] usbcore: registered new interface driver ums-sddr55
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.248000] usbcore: registered new interface driver ums-usbat
Jul 19 14:18:09 OpenWrt kern.info kernel: [   19.288000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.516000] eth0: link forced UP - 100/full - flow control off/off
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.532000] device eth0 entered promiscuous mode
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.540000] br-lan: port 1(eth0) entered forwarding state
Jul 19 14:18:12 OpenWrt kern.info kernel: [   24.544000] br-lan: port 1(eth0) entered forwarding state
Jul 19 14:18:12 OpenWrt daemon.notice netifd: Interface 'lan' is now up
Jul 19 14:18:12 OpenWrt daemon.notice netifd: Interface 'loopback' is now up
Jul 19 14:18:14 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Jul 19 14:18:14 OpenWrt kern.info kernel: [   26.548000] br-lan: port 1(eth0) entered forwarding state
Jul 19 14:18:17 OpenWrt user.info sysinit: Loading defaults
Jul 19 14:18:18 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Jul 19 14:18:18 OpenWrt user.info sysinit: Loading synflood protection
Jul 19 14:18:18 OpenWrt user.info sysinit: Adding custom chains
Jul 19 14:18:19 OpenWrt user.info sysinit: Loading zones
Jul 19 14:18:22 OpenWrt user.info sysinit: Loading forwardings
Jul 19 14:18:22 OpenWrt user.info sysinit: Loading rules
Jul 19 14:18:23 OpenWrt user.info sysinit: Loading redirects
Jul 19 14:18:23 OpenWrt user.info sysinit: Loading includes
Jul 19 14:18:23 OpenWrt user.info sysinit: Optimizing conntrack
Jul 19 14:18:23 OpenWrt user.info sysinit: Loading interfaces
Jul 19 14:18:24 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Jul 19 14:18:26 OpenWrt authpriv.info dropbear[952]: Running in background
Jul 19 14:18:28 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jul 19 14:18:28 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: started, version 2.62 cachesize 150
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using local addresses only for domain lan
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: reading /tmp/resolv.conf.auto
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using nameserver 8.8.8.8#53
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using nameserver 8.8.4.4#53
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: using local addresses only for domain lan
Jul 19 14:18:28 OpenWrt daemon.info dnsmasq[991]: read /etc/hosts - 1 addresses
[/spoiler] system log

gracias.  ;D
Pues esos deberían haber funcionado :$...

Prueba estos otros, ya sabes, hay que reiniciar el router:
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_S29GL128P10.bin
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_MX29LV128DB.bin

Saludos.

Ggarza

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #505 en: 19-07-2012, 16:43 (Jueves) »
Aqui esta el dmesg.txt:

0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Jul 17 19:59:50 CEST 2012
[    0.000000] Detected Broadcom 0x6358 CPU revision a1
[    0.000000] CPU frequency is 300 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 40 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xbe000000
[    0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: HW556
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 61896k/65536k available (2225k kernel code, 3640k reserved, 398k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.068000] registering PCI controller with io_map_base unset
[    0.088000] bio: create slab <bio-0> at 0
[    0.096000] PCI host bridge to bus 0000:00
[    0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.104000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[    0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[    0.124000] Switching to clocksource MIPS
[    0.136000] NET: Registered protocol family 2
[    0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.172000] TCP reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] pci 0000:00:01.0: fixup device configuration
[    0.200000] PCI: CLS 0 bytes, default 16
[    0.204000] audit: initializing netlink socket (disabled)
[    0.212000] type=2000 audit(0.212:1): initialized
[    0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.236000] msgmni has been set to 120
[    0.240000] io scheduler noop registered
[    0.244000] io scheduler deadline registered (default)
[    0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[    0.260000] console [ttyS0] enabled, bootconsole disabled
[    0.276000] physmap platform flash device: 02000000 at 1e000000
[    0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.300000]   Amd/Fujitsu Extended Query version 1.3.
[    0.304000] number of CFI chips: 1
[    0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[    0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[    0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[    0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e40000
[    0.336000] bcm63xxpart: Partition 3 is cal_data offset f60000 and length 20000
[    0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[    0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length f40000
[    0.360000] bcm63xxpart: Spare partition is offset 340004 and length c1fffc
[    0.364000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[    0.380000] 0x000000000000-0x000000020000 : "CFE"
[    0.388000] 0x000000020100-0x000000120000 : "kernel"
[    0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.408000] 0x000000120000-0x000000f60000 : "rootfs"
[    0.420000] mtd: partition "rootfs" set to be root filesystem
[    0.424000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=C20000
[    0.432000] 0x000000340000-0x000000f60000 : "rootfs_data"
[    0.444000] 0x000000f60000-0x000000f80000 : "cal_data"
[    0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[    0.460000] 0x000000020000-0x000000f60000 : "linux"
[    0.480000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.488000] Registered led device: HW556:red:message
[    0.488000] Registered led device: HW556:red:hspa
[    0.492000] Registered led device: HW556:red:dsl
[    0.492000] Registered led device: HW556:red:power
[    0.492000] Registered led device: HW556:red:all
[    0.492000] TCP cubic registered
[    0.496000] NET: Registered protocol family 17
[    0.500000] 8021q: 802.1Q VLAN Support v1.8
[    0.516000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.524000] Freeing unused kernel memory: 196k freed
[    3.236000] eth0: link forced UP - 100/full - flow control off/off
[    3.456000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[    4.520000] There is already a switch registered on the device 'eth0'
[    5.988000] Button Hotplug driver version 0.4.1
[    9.996000] JFFS2 notice: (345) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 3 orphan) found.
[   12.980000] Compat-wireless backport release: compat-wireless-2012-07-13
[   12.984000] Backport based on wireless-testing.git master-2012-07-16
[   12.992000] compat.git: wireless-testing.git
[   13.060000] cfg80211: Calling CRDA to update world regulatory domain
[   13.064000] cfg80211: World regulatory domain updated:
[   13.072000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.080000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.088000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.096000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.104000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.112000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.556000] NET: Registered protocol family 10
[   14.008000] SCSI subsystem initialized
[   14.104000] There is already a switch registered on the device 'eth0'
[   14.460000] usbcore: registered new interface driver usbfs
[   14.468000] usbcore: registered new interface driver hub
[   14.476000] usbcore: registered new device driver usb
[   15.592000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[   15.608000] ath: phy0: Bad EEPROM checksum 0x233e or revision 0x0006
[   15.616000] ath: phy0: Unable to initialize hardware; initialization status: -22
[   15.624000] ath9k 0000:00:01.0: Failed to initialize device
[   15.628000] ath9k: probe of 0000:00:01.0 failed with error -22
[   16.008000] PPP generic driver version 2.4.2
[   16.400000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.692000] NET: Registered protocol family 24
[   16.892000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.000000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[   17.004000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[   17.040000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[   17.056000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   17.064000] hub 1-0:1.0: USB hub found
[   17.068000] hub 1-0:1.0: 2 ports detected
[   17.248000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[   17.632000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[   17.772000] hub 1-1:1.0: USB hub found
[   17.784000] hub 1-1:1.0: 2 ports detected
[   18.076000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.492000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   18.600000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[   18.604000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[   18.612000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[   18.680000] hub 2-0:1.0: USB hub found
[   18.684000] hub 2-0:1.0: 1 port detected
[   18.860000] Initializing USB Mass Storage driver...
[   18.864000] usbcore: registered new interface driver usb-storage
[   18.872000] USB Mass Storage support registered.
[   18.908000] usbcore: registered new interface driver ums-alauda
[   18.944000] usbcore: registered new interface driver ums-cypress
[   18.980000] usbcore: registered new interface driver ums-datafab
[   19.020000] usbcore: registered new interface driver ums-freecom
[   19.056000] usbcore: registered new interface driver ums-isd200
[   19.096000] usbcore: registered new interface driver ums-jumpshot
[   19.132000] usbcore: registered new interface driver ums-karma
[   19.168000] usbcore: registered new interface driver ums-sddr09
[   19.208000] usbcore: registered new interface driver ums-sddr55
[   19.244000] usbcore: registered new interface driver ums-usbat
[   19.284000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   24.856000] eth0: link forced UP - 100/full - flow control off/off
[   24.880000] device eth0 entered promiscuous mode
[   24.892000] br-lan: port 1(eth0) entered forwarding state
[   24.896000] br-lan: port 1(eth0) entered forwarding state
[   26.900000] br-lan: port 1(eth0) entered forwarding state

Como demonios se mete todo el dmesg en un cuadrito de esos q no m sale. Q novato soy. Gracias Noltari., le he estado echando un vistazo al codigo y parece ser q el ckeckcum no es el correcto y da error en el eeprom y no reconoce el wifi o algo asi, tu q entiendes de verdad a ver q m cuentas y si se m pega algo jeje.

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #506 en: 19-07-2012, 17:15 (Jueves) »
Probad el resto de caldata que he puesto a ver si alguno va...

Aquí otro más:
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_danitool2.bin

Saludos

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #507 en: 19-07-2012, 17:16 (Jueves) »
Noltari, no funciona ninguno de los tres, el wifi no aparece, e estado mirando la pagina de openwrt, seria posible que no sea ......of=/dev/mtd4 sino .....of=/dev/mtd3?, bueno no e intentado nada todavía antes de no saber lo que piensas.


Citar
partition    name    function
mtd0    CFE    bootloader
mtd1    kernel    kernel
mtd2    rootfs    root file system
mtd3    ath_data    wifi calibration data
mtd4    nvram    OEM configuration data
sacado de la pagina http://wiki.openwrt.org/toh/huawei/hg556a

gracias  ^-^

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #508 en: 19-07-2012, 17:58 (Jueves) »
Noltari, no funciona ninguno de los tres, el wifi no aparece, e estado mirando la pagina de openwrt, seria posible que no sea ......of=/dev/mtd4 sino .....of=/dev/mtd3?, bueno no e intentado nada todavía antes de no saber lo que piensas.


Citar
partition    name    function
mtd0    CFE    bootloader
mtd1    kernel    kernel
mtd2    rootfs    root file system
mtd3    ath_data    wifi calibration data
mtd4    nvram    OEM configuration data
sacado de la pagina http://wiki.openwrt.org/toh/huawei/hg556a

gracias  ^-^

Cuando utilizas imágenes squashfs, se crea una partición llamada rootfs_data justo después de rootfs, para poder escribir configuración y otros archivos personalizados, puesto que la partición rootfs no se puede tocar.

Saludos.

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #509 en: 19-07-2012, 18:17 (Jueves) »
 :-[ uup es bueno saberlo para no meter la pata gracias por difundir tu sabiduría.

Noltari, e probado los 4 caldatas y no a vuelto el wifi. no creo que este quemado la wifi físicamente, porque el compañero Ggarza tiene el mismo problema, compartimos el mismo juego de  memoria y MAC  (Atheros MX29GL128EH con Mac: 64:16:f0) y el bootlog es casi idéntico.

intentare colocar las imágenes ath_data, desde un firmware de danitol

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #510 en: 19-07-2012, 18:23 (Jueves) »
:-[ uup es bueno saberlo para no meter la pata gracias por difundir tu sabiduría.

Noltari, e probado los 4 caldatas y no a vuelto el wifi. no creo que este quemado la wifi físicamente, porque el compañero Ggarza tiene el mismo problema, compartimos el mismo juego de  memoria y MAC  (Atheros MX29GL128EH con Mac: 64:16:f0) y el bootlog es casi idéntico.

intentare colocar las imágenes ath_data, desde un firmware de danitol
No pruebes esas imágenes en el firmware de danitool porque tienen distinto offset y no van a funcionar.

Sin embargo, prueba esta que me pasó jar229 hace tiempo en el firmware más nuevo de danitool: https://dl.dropbox.com/u/4708147/openwrt/hw556/ath_old_MX29GL128EH.bin

Saludos.

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #511 en: 19-07-2012, 18:45 (Jueves) »
nada de nada,

habría alguna manera de hacer algo mas, a partir del cable serie?.

gracias.  :(

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #512 en: 19-07-2012, 18:59 (Jueves) »
nada de nada,

habría alguna manera de hacer algo mas, a partir del cable serie?.

gracias.  :(
Cualquier otra cosa que se pudiese hacer la teníais que haber hecho antes de probar firmwares sin control, habiendo hecho un backup...

Desconectado jar229

  • Moderador
  • *
  • Mensajes: 4604
Re: OpenWRT en Huawei hg556a
« Respuesta #513 en: 19-07-2012, 19:07 (Jueves) »
Enviado por mail, backup de la partición wifi de uno de mis routers (el otro lo tiene un colega y como poco hasta el mes que viene no lo veré ...)  ;)
Los que habéis perdido el wifi ... mira que se ha avisado en el hilo por activa y por pasiva, antes de instalar nada hay que hacer copia de la partición ...  :'(
Valoraciones positivas en compra/venta:
175 en Htcmania
240 en Har2mano
12 en gsmspain
 ....
 
Mis equipos en venta: https://drive.google.com/open?id=1Zi_bqLSfg_qCT8sx6JhPaWVvSeZXpcka

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #514 en: 19-07-2012, 19:20 (Jueves) »
Enviado por mail, backup de la partición wifi de uno de mis routers (el otro lo tiene un colega y como poco hasta el mes que viene no lo veré ...)  ;)
Los que habéis perdido el wifi ... mira que se ha avisado en el hilo por activa y por pasiva, antes de instalar nada hay que hacer copia de la partición ...  :'(
Totalmente idéntico al archivo que había generado yo con tus datos antiguos :$...

A ver qué se me ocurre...

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #515 en: 19-07-2012, 20:34 (Jueves) »
Deshabilitados los enlaces a mis compilaciones de openwrt para este router por haber podido causar la pérdida del wifi a algún miembro de este foro.

Estoy haciendo los parches de una nueva forma más segura para evitar la pérdida del caldata, haciendo una mezcla de mi procedimiento y el de danitool.

Saludos.

tool

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #516 en: 20-07-2012, 11:21 (Viernes) »
Noltari, se podría hacer que cuando instalases hiciese un "backup" de todo en un pendrive?

Sobre la pérdida de Wifi, sólo afecta a router "rana" no?

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #517 en: 20-07-2012, 12:19 (Viernes) »
¿Alguien con un backup de la partición mtd4 con un ruter atheros podría confirmarme que el wifi le funciona con este firmware?
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32779.bin

Noltari, se podría hacer que cuando instalases hiciese un "backup" de todo en un pendrive?

Sobre la pérdida de Wifi, sólo afecta a router "rana" no?
Todavía no sé a qué routers afecta. Mi sospecha es que podría ser que algunos routers con la flash MX29GL128EH tuvieran las mismas mac que los routers de la MX29LV128DB y esto estaría causando la pérdida de wifi en estos casos en concreto.

Sobre lo del backup de "todo", depende de a qué le llames "todo". En openwrt es muy sencillo hacer backups de la configuración, tienes una sección en LuCI cerca del formulario de actualización. Sin embargo, no se puede hacer un backup de los paquetes instalados, por lo que es mejor utilizar firmwares que lleven todo lo que necesitas para no tener que instalarlos posteriormente en la partición rootfs_data.

Saludos.

emeryth

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #518 en: 20-07-2012, 15:07 (Viernes) »
hola Noltari, e instalado el firmware r32779 sin problemas, pero no aparece el wifi. intento instalar los caldatas que me pasastes?

PD: te lo aseguro mi router tiene memoria MX29GL128EH y su mac es  64:16:f0( como los de MX29LV128DB)

Noltari

  • Visitante
Re: OpenWRT en Huawei hg556a
« Respuesta #519 en: 20-07-2012, 15:50 (Viernes) »
hola Noltari, e instalado el firmware r32779 sin problemas, pero no aparece el wifi. intento instalar los caldatas que me pasastes?

PD: te lo aseguro mi router tiene memoria MX29GL128EH y su mac es  64:16:f0( como los de MX29LV128DB)
Sí, prueba con los caldata que te pasé con este firmware.

EDIT: Ya no me acuerdo de a quién le he pasado los caldata más nuevos y a quién no :$...
Prueba estos:
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath9k/ath1.bin
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath9k/ath2.bin
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath9k/ath3.bin
https://dl.dropbox.com/u/4708147/openwrt/hw556/ath9k/ath4.bin

Saludos.
« Última modificación: 20-07-2012, 15:52 (Viernes) por Noltari »