no se sí te sirva de algo, pero te envió el bootlog del firmware de danitool, que esta publicado en la primera pagina (el especifico para 29LV128DBT)
[spoiler]
CFE version cfe.d081.5003 for BCM96358 (32bit,SP,BE)
Build Date: Wed Nov 11 10:36:35 CST 2009 (Lihua_68693)
Copyright (C) 2006 Huawei Technologies Co. Ltd.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
@w45260: Flash Manufacture id :c2
@w45260Flash Device id :227a
@w45260flipCFIGeometry:0
Parallel flash device: name MX29LV128DB, id 0x227a, size 16384KB
*** GetHG556aBoardVersion = <0> ***
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
Total memory: 67108864 bytes (64MB)
Total memory used by CFE: 0x80401000 - 0x8052A510 (1217808)
Initialized Data: 0x8041F3C0 - 0x80421B60 (10144)
BSS Area: 0x80421B60 - 0x80428510 (27056)
Local Heap: 0x80428510 - 0x80528510 (1048576)
Stack Area: 0x80528510 - 0x8052A510 (8192)
Text (code) segment: 0x80401000 - 0x8041F3B4 (123828)
Boot area (physical): 0x0052B000 - 0x0056B000
Relocation Factor: I:00000000 - D:00000000
*** GetHG556aBoardVersion = <0> ***
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : HW556
Psi size in KB : 64
Number of MAC Addresses (1-32) : 10
Base MAC Address : 64:16:f0:0a:87:2d
Ethernet PHY Type : Internal
Memory size in MB : 64
CMT Thread Number : 1
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
boot kernel from be020100
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[ 0.000000] Linux version 2.6.39.4 (dani@tool) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #34 Wed Jan 4 22:16:19 CET 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 62016k/65536k available (2145k kernel code, 3520k reserved, 368k data, 160k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.064000] MPI_CSBASE_REG(0) = 0x1e000000
[ 0.068000] changed ath9k regdomain to 0xff
[ 0.072000] registering PCI controller with io_map_base unset
[ 0.084000] bio: create slab <bio-0> at 0
[ 0.092000] pci 0000:00:01.0: fixup device configuration
[ 0.096000] pci-ath9k-fixup: Writing 0x0029168c to register 0x6000
[ 0.100000] pci-ath9k-fixup: Writing 0x02800001 to register 0x6008
[ 0.104000] pci-ath9k-fixup: Writing 0x2091168c to register 0x602c
[ 0.108000] pci-ath9k-fixup: Writing 0x002a168c to register 0x5000
[ 0.112000] pci-ath9k-fixup: Writing 0x02800001 to register 0x5008
[ 0.116000] pci-ath9k-fixup: Writing 0x2091168c to register 0x502c
[ 0.120000] pci-ath9k-fixup: Writing 0x05040cc0 to register 0x5064
[ 0.124000] pci-ath9k-fixup: Writing 0x00033811 to register 0x506c
[ 0.128000] pci-ath9k-fixup: Writing 0x0040073b to register 0x4004
[ 0.132000] pci-ath9k-fixup: Writing 0x00000003 to register 0x4074
[ 0.136000] pci-ath9k-fixup: Writing 0x01c20000 to register 0x4000
[ 0.140000] pci-ath9k-fixup: Writing 0x00000044 to register 0x6034
[ 0.144000] pci-ath9k-fixup: Device vendor 0x168c, id 0x0029
[ 0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.168000] pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x3000ffff] (PCI address [0x30000000-0x3000ffff])
[ 0.172000] Switching to clocksource MIPS
[ 0.184000] NET: Registered protocol family 2
[ 0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.196000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.204000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.212000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.216000] TCP reno registered
[ 0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.236000] NET: Registered protocol family 1
[ 0.240000] audit: initializing netlink socket (disabled)
[ 0.248000] type=2000 audit(0.248:1): initialized
[ 0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.260000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.272000] msgmni has been set to 121
[ 0.276000] io scheduler noop registered
[ 0.280000] io scheduler deadline registered (default)
[ 0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.292000] console [ttyS0] enabled, bootconsole disabled
[ 0.292000] console [ttyS0] enabled, bootconsole disabled
[ 0.308000] bcm963xx-flash bcm963xx-flash.0: 0x02000000 at 0x1e000000
[ 0.316000] Number of erase regions: 2
[ 0.320000] Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
[ 0.328000] Primary Algorithm Table at 0040
[ 0.332000] Alternative Vendor Command Set: 0000 (None)
[ 0.336000] No Alternate Algorithm Table
[ 0.340000] Vcc Minimum: 3.0 V
[ 0.344000] Vcc Maximum: 3.6 V
[ 0.348000] No Vpp line
[ 0.348000] Typical byte/word write timeout: 16 µs
[ 0.356000] Maximum byte/word write timeout: 512 µs
[ 0.360000] Full buffer write not supported
[ 0.364000] Typical block erase timeout: 1024 ms
[ 0.368000] Maximum block erase timeout: 16384 ms
[ 0.372000] Chip erase not supported
[ 0.376000] Device size: 0x1000000 bytes (16 MiB)
[ 0.380000] Flash Device Interface description: 0x0002
[ 0.388000] - supports x8 and x16 via BYTE# with asynchronous interface
[ 0.392000] Max. bytes in buffer write: 0x1
[ 0.400000] Number of Erase Block Regions: 2
[ 0.404000] Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
[ 0.408000] Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
[ 0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
[ 0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.432000] Amd/Fujitsu Extended Query version 1.3.
[ 0.436000] Silicon revision: 0
[ 0.440000] Address sensitive unlock: Required
[ 0.444000] Erase Suspend: Read/write
[ 0.448000] Block protection: 4 sectors per group
[ 0.452000] Temporary block unprotect: Supported
[ 0.460000] Block protect/unprotect scheme: 4
[ 0.464000] Number of simultaneous operations: 0
[ 0.468000] Burst mode: Not supported
[ 0.472000] Page mode: Not supported
[ 0.476000] Vpp Supply Minimum Program/Erase Voltage: 10.5 V
[ 0.480000] Vpp Supply Maximum Program/Erase Voltage: 11.5 V
[ 0.488000] Top/Bottom Boot Block: Bottom boot
[ 0.492000] number of CFI chips: 1
[ 0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
[ 0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
[ 0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
[ 0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
[ 0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
[ 0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
[ 0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
[ 0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
[ 0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
[ 0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
[ 0.568000] Creating 6 MTD partitions on "bcm963xx":
[ 0.576000] 0x000000000000-0x000000020000 : "CFE"
[ 0.584000] 0x000000020100-0x000000100000 : "kernel"
[ 0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.604000] 0x000000100000-0x000000e00000 : "rootfs"
[ 0.612000] mtd: partition "rootfs" set to be root filesystem
[ 0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
[ 0.648000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.656000] 0x000000020000-0x000000e00000 : "linux"
[ 0.672000] bcm63xx-wdt bcm63xx-wdt.0: started, timer margin: 30 sec
[ 0.684000] TCP westwood registered
[ 0.688000] NET: Registered protocol family 17
[ 0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.700000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.724000] Freeing unused kernel memory: 160k freed
awk: /proc/cpuinfo: No such file or directory
[ 3.592000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.660000] There is already a switch registered on the device 'eth0'
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 9.284000] JFFS2 notice: (317) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 5 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 12.800000] Compat-wireless backport release: compat-wireless-2011-11-29
[ 12.808000] Backport based on wireless-testing.git master-2011-12-01
[ 13.032000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.844000] cfg80211: World regulatory domain updated:
[ 13.852000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.868000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.876000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.884000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.892000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.580000] SCSI subsystem initialized
[ 14.680000] There is already a switch registered on the device 'eth0'
[ 15.076000] usbcore: registered new interface driver usbfs
[ 15.084000] usbcore: registered new interface driver hub
[ 15.096000] usbcore: registered new device driver usb
[ 16.680000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 16.688000] board_bcm963xx: Setting device platform data
[ 16.700000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[ 16.708000] ath: random mac address will be used: 2e:d2:a1:a8:80:0b
[ 16.728000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[ 16.740000] cfg80211: Calling CRDA for country: JP
[ 16.892000] cfg80211: Regulatory domain changed to country: JP
[ 16.900000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.908000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.916000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 16.924000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 16.932000] cfg80211: (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.940000] cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[ 16.948000] cfg80211: (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.952000] cfg80211: (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.960000] cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[ 16.968000] cfg80211: (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.976000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.984000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.992000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[ 17.040000] Button Hotplug driver version 0.4.1
[ 18.016000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 18.568000] PPP generic driver version 2.4.2
[ 18.796000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.120000] NET: Registered protocol family 24
[ 19.368000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 19.372000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 19.380000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 19.412000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 19.428000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 19.436000] hub 1-0:1.0: USB hub found
[ 19.440000] hub 1-0:1.0: 2 ports detected
[ 19.756000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
[ 19.876000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
[ 20.260000] hub 1-1:1.0: USB hub found
[ 20.272000] hub 1-1:1.0: 2 ports detected
[ 20.680000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.684000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 20.692000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 20.700000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 20.768000] hub 2-0:1.0: USB hub found
[ 20.772000] hub 2-0:1.0: 1 port detected
[ 21.052000] Initializing USB Mass Storage driver...
[ 21.056000] usbcore: registered new interface driver usb-storage
[ 21.064000] USB Mass Storage support registered.
[ 21.276000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[ 23.288000] eth0: link forced UP - 100/full - flow control off/off
[ 23.732000] device eth0 entered promiscuous mode
[ 23.828000] br-lan: port 1(eth0) entering forwarding state
[ 23.832000] br-lan: port 1(eth0) entering forwarding state[/spoiler] es esl bootlog que me da la ventana serie
[spoiler]Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.348000] No Vpp line
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.348000] Typical byte/word write timeout: 16 µs
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.356000] Maximum byte/word write timeout: 512 µs
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.360000] Full buffer write not supported
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.364000] Typical block erase timeout: 1024 ms
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.368000] Maximum block erase timeout: 16384 ms
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.372000] Chip erase not supported
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.376000] Device size: 0x1000000 bytes (16 MiB)
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.404000] Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.408000] Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 0.424000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.424000] Amd/Fujitsu Extended Query Table at 0x0040
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.432000] Amd/Fujitsu Extended Query version 1.3.
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.436000] Silicon revision: 0
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.440000] Address sensitive unlock: Required
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.444000] Erase Suspend: Read/write
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.448000] Block protection: 4 sectors per group
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.452000] Temporary block unprotect: Supported
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.460000] Block protect/unprotect scheme: 4
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.464000] Number of simultaneous operations: 0
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.468000] Burst mode: Not supported
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.472000] Page mode: Not supported
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.476000] Vpp Supply Minimum Program/Erase Voltage: 10.5 V
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.480000] Vpp Supply Maximum Program/Erase Voltage: 11.5 V
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.488000] Top/Bottom Boot Block: Bottom boot
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.492000] number of CFI chips: 1
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.584000] 0x000000020100-0x000000100000 : "kernel"
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.604000] 0x000000100000-0x000000e00000 : "rootfs"
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.612000] mtd: partition "rootfs" set to be root filesystem
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.648000] 0x000000fe0000-0x000001000000 : "nvram"
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 0.656000] 0x000000020000-0x000000e00000 : "linux"
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.672000] bcm63xx-wdt bcm63xx-wdt.0: started, timer margin: 30 sec
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 0.680000] Registered led device: message
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 0.680000] Registered led device: hspa
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 0.680000] Registered led device: dsl
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 0.680000] Registered led device: power
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 0.680000] Registered led device: all_leds
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.684000] TCP westwood registered
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.688000] NET: Registered protocol family 17
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.700000] All bugs added by David S. Miller <davem@redhat.com>
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 0.724000] Freeing unused kernel memory: 160k freed
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 3.584000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 4.656000] There is already a switch registered on the device 'eth0'
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 12.672000] Compat-wireless backport release: compat-wireless-2011-11-29
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 12.680000] Backport based on wireless-testing.git master-2011-12-01
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 12.904000] cfg80211: Calling CRDA to update world regulatory domain
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 13.760000] cfg80211: World regulatory domain updated:
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 13.764000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 13.808000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Sep 8 15:44:11 OpenWrt kern.notice kernel: [ 14.452000] SCSI subsystem initialized
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 14.552000] There is already a switch registered on the device 'eth0'
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 14.952000] usbcore: registered new interface driver usbfs
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 14.956000] usbcore: registered new interface driver hub
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 14.968000] usbcore: registered new device driver usb
Sep 8 15:44:11 OpenWrt kern.warn kernel: [ 16.552000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.560000] board_bcm963xx: Setting device platform data
Sep 8 15:44:11 OpenWrt kern.err kernel: [ 16.576000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
Sep 8 15:44:11 OpenWrt kern.err kernel: [ 16.580000] ath: random mac address will be used: 22:9f:90:3e:7a:be
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 16.588000] ath: EEPROM regdomain: 0xff
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 16.588000] ath: EEPROM indicates we should expect a direct regpair map
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 16.588000] ath: Country alpha2 being used: JP
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 16.588000] ath: Regpair used: 0xff
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 16.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sep 8 15:44:11 OpenWrt kern.debug kernel: [ 16.600000] Registered led device: ath9k-phy0
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.600000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.612000] cfg80211: Calling CRDA for country: JP
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.776000] cfg80211: Regulatory domain changed to country: JP
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.784000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.792000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.800000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.808000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.816000] cfg80211: (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.824000] cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.832000] cfg80211: (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.840000] cfg80211: (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.848000] cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.872000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.880000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 16.916000] Button Hotplug driver version 0.4.1
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 17.892000] NTFS driver 2.1.30 [Flags: R/O MODULE].
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 18.444000] PPP generic driver version 2.4.2
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 18.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 18.996000] NET: Registered protocol family 24
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.248000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.252000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.260000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.292000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.308000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.316000] hub 1-0:1.0: USB hub found
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.320000] hub 1-0:1.0: 2 ports detected
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.640000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 19.756000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.140000] hub 1-1:1.0: USB hub found
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.152000] hub 1-1:1.0: 2 ports detected
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.568000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.576000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.584000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.648000] hub 2-0:1.0: USB hub found
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.652000] hub 2-0:1.0: 1 port detected
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.932000] Initializing USB Mass Storage driver...
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.940000] usbcore: registered new interface driver usb-storage
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 20.944000] USB Mass Storage support registered.
Sep 8 15:44:11 OpenWrt kern.info kernel: [ 21.156000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 23.808000] eth0: link forced UP - 100/full - flow control off/off
Sep 8 15:44:12 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 24.220000] device eth0 entered promiscuous mode
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 24.320000] br-lan: port 1(eth0) entering forwarding state
Sep 8 15:44:12 OpenWrt kern.info kernel: [ 24.328000] br-lan: port 1(eth0) entering forwarding state
Sep 8 15:44:14 OpenWrt user.info sysinit: 'radio0' is disabled
Sep 8 15:44:15 OpenWrt user.info sysinit: 'radio0' is disabled
Sep 8 15:44:15 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Sep 8 15:44:18 OpenWrt user.info sysinit: Loading defaults
Sep 8 15:44:18 OpenWrt user.info sysinit: Loading synflood protection
Sep 8 15:44:19 OpenWrt user.info sysinit: Adding custom chains
Sep 8 15:44:20 OpenWrt user.info sysinit: Loading zones
Sep 8 15:44:21 OpenWrt user.info sysinit: Loading forwardings
Sep 8 15:44:21 OpenWrt user.info sysinit: Loading redirects
Sep 8 15:44:21 OpenWrt user.info sysinit: Loading rules
Sep 8 15:44:22 OpenWrt user.info sysinit: Loading includes
Sep 8 15:44:22 OpenWrt user.info sysinit: Optimizing conntrack
Sep 8 15:44:22 OpenWrt user.info sysinit: Loading interfaces
Sep 8 15:44:22 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Sep 8 15:44:25 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sep 8 15:44:25 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sep 8 15:44:29 OpenWrt daemon.info dnsmasq[956]: started, version 2.59 cachesize 150
Sep 8 15:44:29 OpenWrt daemon.info dnsmasq[956]: compile time options: IPv6 GNU-getopt no-DBus no-i18n DHCP TFTP no-conntrack no-IDN
Sep 8 15:44:29 OpenWrt daemon.info dnsmasq-dhcp[956]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sep 8 15:44:29 OpenWrt daemon.info dnsmasq[956]: using local addresses only for domain lan
Sep 8 15:44:29 OpenWrt daemon.warn dnsmasq[956]: no servers found in /tmp/resolv.conf.auto, will retry
Sep 8 15:44:29 OpenWrt daemon.info dnsmasq[956]: read /etc/hosts - 1 addresses
Sep 8 15:44:29 OpenWrt daemon.info dnsmasq-dhcp[956]: read /etc/ethers - 0 addresses
Sep 8 15:44:30 OpenWrt kern.warn kernel: [ 41.976000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
Sep 8 15:44:30 OpenWrt kern.warn kernel: [ 41.984000] jffs2_build_filesystem(): unlocking the mtd device... done.
Sep 8 15:46:08 OpenWrt kern.warn kernel: [ 41.988000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
Sep 8 15:46:08 OpenWrt kern.notice kernel: [ 139.712000] JFFS2 notice: (978) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sep 8 15:46:08 OpenWrt auth.err passwd: /etc/passwd: Read-only file system
Sep 8 15:46:08 OpenWrt auth.err passwd: can't update password file /etc/passwd
Sep 8 15:46:08 OpenWrt user.info sysinit: copying files ... done
Sep 8 15:46:10 OpenWrt authpriv.info dropbear[1766]: Running in background
[/spoiler] esto es el system log de luci
[spoiler][ 0.000000] Linux version 2.6.39.4 (dani@tool) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #34 Wed Jan 4 22:16:19 CET 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802840e0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 62016k/65536k available (2145k kernel code, 3520k reserved, 368k data, 160k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.064000] MPI_CSBASE_REG(0) = 0x1e000000
[ 0.068000] changed ath9k regdomain to 0xff
[ 0.072000] registering PCI controller with io_map_base unset
[ 0.084000] bio: create slab <bio-0> at 0
[ 0.092000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[ 0.092000] pci 0000:00:01.0: fixup device configuration
[ 0.096000] pci-ath9k-fixup: Writing 0x0029168c to register 0x6000
[ 0.100000] pci-ath9k-fixup: Writing 0x02800001 to register 0x6008
[ 0.104000] pci-ath9k-fixup: Writing 0x2091168c to register 0x602c
[ 0.108000] pci-ath9k-fixup: Writing 0x002a168c to register 0x5000
[ 0.112000] pci-ath9k-fixup: Writing 0x02800001 to register 0x5008
[ 0.116000] pci-ath9k-fixup: Writing 0x2091168c to register 0x502c
[ 0.120000] pci-ath9k-fixup: Writing 0x05040cc0 to register 0x5064
[ 0.124000] pci-ath9k-fixup: Writing 0x00033811 to register 0x506c
[ 0.128000] pci-ath9k-fixup: Writing 0x0040073b to register 0x4004
[ 0.132000] pci-ath9k-fixup: Writing 0x00000003 to register 0x4074
[ 0.136000] pci-ath9k-fixup: Writing 0x01c20000 to register 0x4000
[ 0.140000] pci-ath9k-fixup: Writing 0x00000044 to register 0x6034
[ 0.144000] pci-ath9k-fixup: Device vendor 0x168c, id 0x0029
[ 0.148000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.160000] pci 0000:00:01.0: PME# supported from D0 D3hot
[ 0.160000] pci 0000:00:01.0: PME# disabled
[ 0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.168000] pci 0000:00:01.0: BAR 0: set to [mem 0x30000000-0x3000ffff] (PCI address [0x30000000-0x3000ffff])
[ 0.172000] Switching to clocksource MIPS
[ 0.184000] NET: Registered protocol family 2
[ 0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.196000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.204000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.212000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.216000] TCP reno registered
[ 0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.236000] NET: Registered protocol family 1
[ 0.240000] PCI: CLS 0 bytes, default 32
[ 0.240000] audit: initializing netlink socket (disabled)
[ 0.248000] type=2000 audit(0.248:1): initialized
[ 0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.260000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.272000] msgmni has been set to 121
[ 0.276000] io scheduler noop registered
[ 0.280000] io scheduler deadline registered (default)
[ 0.284000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.292000] console [ttyS0] enabled, bootconsole disabled
[ 0.308000] bcm963xx-flash bcm963xx-flash.0: 0x02000000 at 0x1e000000
[ 0.316000] Number of erase regions: 2
[ 0.320000] Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
[ 0.328000] Primary Algorithm Table at 0040
[ 0.332000] Alternative Vendor Command Set: 0000 (None)
[ 0.336000] No Alternate Algorithm Table
[ 0.340000] Vcc Minimum: 3.0 V
[ 0.344000] Vcc Maximum: 3.6 V
[ 0.348000] No Vpp line
[ 0.348000] Typical byte/word write timeout: 16 µs
[ 0.356000] Maximum byte/word write timeout: 512 µs
[ 0.360000] Full buffer write not supported
[ 0.364000] Typical block erase timeout: 1024 ms
[ 0.368000] Maximum block erase timeout: 16384 ms
[ 0.372000] Chip erase not supported
[ 0.376000] Device size: 0x1000000 bytes (16 MiB)
[ 0.380000] Flash Device Interface description: 0x0002
[ 0.388000] - supports x8 and x16 via BYTE# with asynchronous interface
[ 0.392000] Max. bytes in buffer write: 0x1
[ 0.400000] Number of Erase Block Regions: 2
[ 0.404000] Erase Region #0: BlockSize 0x2000 bytes, 8 blocks
[ 0.408000] Erase Region #1: BlockSize 0x10000 bytes, 255 blocks
[ 0.416000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227a,
[ 0.424000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
[ 0.424000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.432000] Amd/Fujitsu Extended Query version 1.3.
[ 0.436000] Silicon revision: 0
[ 0.440000] Address sensitive unlock: Required
[ 0.444000] Erase Suspend: Read/write
[ 0.448000] Block protection: 4 sectors per group
[ 0.452000] Temporary block unprotect: Supported
[ 0.460000] Block protect/unprotect scheme: 4
[ 0.464000] Number of simultaneous operations: 0
[ 0.468000] Burst mode: Not supported
[ 0.472000] Page mode: Not supported
[ 0.476000] Vpp Supply Minimum Program/Erase Voltage: 10.5 V
[ 0.480000] Vpp Supply Maximum Program/Erase Voltage: 11.5 V
[ 0.488000] Top/Bottom Boot Block: Bottom boot
[ 0.492000] number of CFI chips: 1
[ 0.496000] bcm963xx_flash: Read Signature value of CFE1CFE1
[ 0.500000] bcm963xx-flash bcm963xx-flash.0: CFE bootloader detected
[ 0.508000] bcm963xx_flash: CFE boot tag found with version 8 and board type HW556
[ 0.516000] bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
[ 0.524000] bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
[ 0.532000] bcm963xx_flash: Partition 2 is rootfs offset 100000 and length d00000
[ 0.540000] bcm963xx_flash: Partition 3 is ath_data offset e00000 and length 1e0000
[ 0.548000] bcm963xx_flash: Partition 4 is nvram offset fe0000 and length 20000
[ 0.552000] bcm963xx_flash: Partition 5 is linux offset 20000 and length de0000
[ 0.560000] bcm963xx_flash: Spare partition is 360000 offset and length aa0000
[ 0.568000] Creating 6 MTD partitions on "bcm963xx":
[ 0.576000] 0x000000000000-0x000000020000 : "CFE"
[ 0.584000] 0x000000020100-0x000000100000 : "kernel"
[ 0.588000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.604000] 0x000000100000-0x000000e00000 : "rootfs"
[ 0.612000] mtd: partition "rootfs" set to be root filesystem
[ 0.620000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.628000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.636000] 0x000000e00000-0x000000fe0000 : "ath_data"
[ 0.648000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.656000] 0x000000020000-0x000000e00000 : "linux"
[ 0.672000] bcm63xx-wdt bcm63xx-wdt.0: started, timer margin: 30 sec
[ 0.680000] Registered led device: message
[ 0.680000] Registered led device: hspa
[ 0.680000] Registered led device: dsl
[ 0.680000] Registered led device: power
[ 0.680000] Registered led device: all_leds
[ 0.684000] TCP westwood registered
[ 0.688000] NET: Registered protocol family 17
[ 0.692000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.700000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.716000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.724000] Freeing unused kernel memory: 160k freed
[ 3.584000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.656000] There is already a switch registered on the device 'eth0'
[ 12.672000] Compat-wireless backport release: compat-wireless-2011-11-29
[ 12.680000] Backport based on wireless-testing.git master-2011-12-01
[ 12.904000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.760000] cfg80211: World regulatory domain updated:
[ 13.764000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.772000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.780000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.792000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.808000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.452000] SCSI subsystem initialized
[ 14.552000] There is already a switch registered on the device 'eth0'
[ 14.952000] usbcore: registered new interface driver usbfs
[ 14.956000] usbcore: registered new interface driver hub
[ 14.968000] usbcore: registered new device driver usb
[ 16.552000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 16.560000] board_bcm963xx: Setting device platform data
[ 16.576000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[ 16.580000] ath: random mac address will be used: 22:9f:90:3e:7a:be
[ 16.588000] ath: EEPROM regdomain: 0xff
[ 16.588000] ath: EEPROM indicates we should expect a direct regpair map
[ 16.588000] ath: Country alpha2 being used: JP
[ 16.588000] ath: Regpair used: 0xff
[ 16.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 16.600000] Registered led device: ath9k-phy0
[ 16.600000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[ 16.612000] cfg80211: Calling CRDA for country: JP
[ 16.776000] cfg80211: Regulatory domain changed to country: JP
[ 16.784000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.792000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.800000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 16.808000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 16.816000] cfg80211: (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.824000] cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[ 16.832000] cfg80211: (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.840000] cfg80211: (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.848000] cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[ 16.856000] cfg80211: (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[ 16.864000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.872000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.880000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[ 16.916000] Button Hotplug driver version 0.4.1
[ 17.892000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 18.444000] PPP generic driver version 2.4.2
[ 18.672000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.996000] NET: Registered protocol family 24
[ 19.248000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 19.252000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 19.260000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 19.292000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 19.308000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 19.316000] hub 1-0:1.0: USB hub found
[ 19.320000] hub 1-0:1.0: 2 ports detected
[ 19.640000] nf_conntrack version 0.5.0 (971 buckets, 3884 max)
[ 19.756000] usb 1-1: new high speed USB device number 2 using bcm63xx_ehci
[ 20.140000] hub 1-1:1.0: USB hub found
[ 20.152000] hub 1-1:1.0: 2 ports detected
[ 20.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.568000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 20.576000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 20.584000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 20.648000] hub 2-0:1.0: USB hub found
[ 20.652000] hub 2-0:1.0: 1 port detected
[ 20.932000] Initializing USB Mass Storage driver...
[ 20.940000] usbcore: registered new interface driver usb-storage
[ 20.944000] USB Mass Storage support registered.
[ 21.156000] input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
[ 23.808000] eth0: link forced UP - 100/full - flow control off/off
[ 24.220000] device eth0 entered promiscuous mode
[ 24.320000] br-lan: port 1(eth0) entering forwarding state
[ 24.328000] br-lan: port 1(eth0) entering forwarding state
[ 41.976000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 41.984000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 41.988000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 139.712000] JFFS2 notice: (978) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler] esto es el kernel log de luci
