Para esto necesito que alguno pruebe este firmware, que es exactamente idéntico al anterior pero con los debugs.
https://dl.dropbox.com/u/4708147/openwrt/63281T/openwrt-963281T_TEF-generic-squashfs-cfe.bin
Saludos!
Ahí va el
dmesg[spoiler][ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #3 Wed Jul 4 20:20:32 CEST 2012
[ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: A4001N-V0003
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 963281T_TEF
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802a5a60, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 29376k/32768k available (2248k kernel code, 3392k reserved, 399k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.276000] registering PCI controller with io_map_base unset
[ 0.288000] bio: create slab <bio-0> at 0
[ 0.296000] PCI host bridge to bus 0000:00
[ 0.300000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
[ 0.304000] pci_bus 0000:00: root bus resource [
0x00000000 flags 0x0]
[ 0.308000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604
[ 0.308000] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.308000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280
[ 0.308000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
[ 0.308000] pci 0000:01:00.0: supports D1 D2
[ 0.308000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[ 0.312000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[ 0.316000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[ 0.320000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
[ 0.324000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.328000] Switching to clocksource MIPS
[ 0.336000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 0.344000] bcma: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
[ 0.348000] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[ 0.360000] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[ 0.368000] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[ 0.376000] bcma: Found rev 6 PMU (capabilities 0x108C2606)
[ 0.376000] bcma: PMU resource config unknown or not needed for device 0xA8D9
[ 0.376000] bcma: Workarounds unknown or not needed for device 0xA8D9
[ 0.408000] [Hauke] bus->drv_cc.core->id.rev :: 0x22[Hauke] bus->drv_cc.capabilities :: 0x58500000[Hauke] srom_control :: 0x3
[ 0.416000] bcma: SPROM offset 0x800
[ 0.456000] bcma: Using SPROM revision 8 provided by platform.
[ 0.460000] bcma: Bus registered
[ 0.464000] NET: Registered protocol family 2
[ 0.468000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.476000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.484000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.488000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.496000] TCP reno registered
[ 0.500000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.504000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.512000] NET: Registered protocol family 1
[ 0.516000] PCI: CLS 0 bytes, default 16
[ 0.520000] audit: initializing netlink socket (disabled)
[ 0.524000] type=2000 audit(0.524:1): initialized
[ 0.532000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.536000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.548000] msgmni has been set to 57
[ 0.552000] io scheduler noop registered
[ 0.556000] io scheduler deadline registered (default)
[ 0.564000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
[ 0.572000] console [ttyS0] enabled, bootconsole disabled
[ 0.588000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.596000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.600000] bcm63xxpart: CFE boot tag found with version 6 and board type 963281T_TEF
[ 0.608000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.616000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00
[ 0.624000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000
[ 0.628000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[ 0.636000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[ 0.644000] bcm63xxpart: Spare partition is offset 2e0004 and length d0fffc
[ 0.652000] 5 bcm63xxpart partitions found on MTD device spi0.0
[ 0.656000] Creating 5 MTD partitions on "spi0.0":
[ 0.664000] 0x000000000000-0x000000010000 : "CFE"
[ 0.672000] 0x000000010100-0x000000100000 : "kernel"
[ 0.676000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.692000] 0x000000100000-0x000000ff0000 : "rootfs"
[ 0.700000] mtd: partition "rootfs" set to be root filesystem
[ 0.704000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=D10000
[ 0.712000] 0x0000002e0000-0x000000ff0000 : "rootfs_data"
[ 0.720000] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.728000] 0x000000010000-0x000000ff0000 : "linux"
[ 0.772000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.780000] Registered led device: 963281T_TEF:green:power
[ 0.780000] Registered led device: 963281T_TEF:red:stop
[ 0.780000] Registered led device: 963281T_TEF:green:inet
[ 0.784000] Registered led device: 963281T_TEF:red:inet-fail
[ 0.784000] Registered led device: 963281T_TEF:green:ppp
[ 0.784000] Registered led device: 963281T_TEF:red:ppp-fail
[ 0.784000] Registered led device: 963281T_TEF:green:3g
[ 0.784000] Registered led device: 963281T_TEF:red:3g-fail
[ 0.784000] Registered led device: 963281T_TEF:green:wlan
[ 0.784000] Registered led device: 963281T_TEF:red:wlan-fail
[ 0.784000] Registered led device: 963281T_TEF:green:eth
[ 0.788000] Registered led device: 963281T_TEF:red:eth-fail
[ 0.788000] TCP cubic registered
[ 0.792000] NET: Registered protocol family 17
[ 0.796000] 8021q: 802.1Q VLAN Support v1.8
[ 0.808000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.816000] Freeing unused kernel memory: 200k freed
[ 3.336000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 3.392000] roboswitch: Probing device eth0:
[ 3.396000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external
[ 3.404000] No Robo switch in managed mode found, phy_id = 0xffffffff
[ 3.412000] roboswitch: Probing device eth1: No such device
[ 3.416000] roboswitch: Probing device eth2: No such device
[ 3.424000] roboswitch: Probing device eth3: No such device
[ 12.000000] Compat-wireless backport release: compat-wireless-2012-06-14
[ 12.008000] Backport based on wireless-testing.git master-2012-06-14
[ 12.016000] compat.git: wireless-testing.git
[ 12.072000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.076000] cfg80211: World regulatory domain updated:
[ 12.084000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.092000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.108000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.116000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.124000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.512000] NET: Registered protocol family 10
[ 12.616000] There is already a switch registered on the device 'eth0'
[ 12.624000] roboswitch: Probing device eth1: No such device
[ 12.628000] roboswitch: Probing device eth2: No such device
[ 12.636000] roboswitch: Probing device eth3: No such device
[ 13.024000] Button Hotplug driver version 0.4.1
[ 13.188000] PPP generic driver version 2.4.2
[ 13.620000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31
[ 13.984000] bcma: Switched to core: 0x812
[ 13.984000] brcmsmac: use fifi: 20, 192, 192, 21, 17, 5
[ 13.992000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 14.004000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.212000] NET: Registered protocol family 24
[ 14.248000] nf_conntrack version 0.5.0 (462 buckets, 1848 max)
[ 14.624000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.912000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 20.896000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 20.904000] device eth0 entered promiscuous mode
[ 20.912000] br-lan: port 1(eth0) entered forwarding state
[ 20.916000] br-lan: port 1(eth0) entered forwarding state
[ 22.920000] br-lan: port 1(eth0) entered forwarding state
[ 31.328000] eth0: no IPv6 routers present
[ 38.532000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 38.540000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 38.548000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 131.648000] JFFS2 notice: (1050) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[/spoiler]
