buenas,
Hay un led que debe parpadear mientras el router inicia, el power. El parche tiene mal el nombre:
Index: target/linux/brcm63xx/base-files/lib/brcm63xx.sh
===================================================================
--- target/linux/brcm63xx/base-files/lib/brcm63xx.sh (revisión: 32489)
+++ target/linux/brcm63xx/base-files/lib/brcm63xx.sh (copia de trabajo)
@@ -26,6 +26,10 @@
status_led="963281TAN::power"
ifname=eth0
;;
+ 963281T_TEF)
+ status_led="963281T_TEF::power"
+ ifname=eth0
+ ;;
en la definición de leds lo llamaste 963281T_TEF:green:power
Adjunto el log del fw original. Hay una cosa común a los broadcom con el driver propietario y es este mensaje:
[spoiler]wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2[/spoiler]
la verdad es que el router tiene una partición nvram, y por un momento pensé que como los soc 47xx cogen la srom de ahí, pero por el contenido parecen dos copias de la configuración del router con el fw original...
![Tongue :P](https://foro.seguridadwireless.net/Smileys/nostalgia/nn.gif)
Saludos
BOOTLOG[spoiler]CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.10
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : run.bin
Default host flash file name : 2.bin
Boot delay (0-9 seconds) : 9
Board Id (0-4) : 963281T_TEF
Number of MAC Addresses (1-32) : 11
Base MAC Address : 30:39:f2:87:8f:41
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 1
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 9
web info: Waiting for connection on socket 0.
web info: Waiting for connection on socket 1.
web info: Waiting for connection on socket 2.
web info: Waiting for connection on socket 0.
web info: Waiting for connection on socket 1.
web info: Upload 6818609 bytes, Broadcom image format.
web info: Waiting for connection on socket 0.
Flashing root file system and kernel at 0xb8800000: .....................................................
.
*** Image flash done *** !
Resetting board...HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.10
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : run.bin
Default host flash file name : 2.bin
Boot delay (0-9 seconds) : 9
Boot image (0=latest, 1=previous) : 0
Board Id (0-4) : 963281T_TEF
Number of MAC Addresses (1-32) : 11
Base MAC Address : 30:39:f2:87:8f:41
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 1
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Booting from latest image (0xb8800000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (zu1costast@thorold) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Thu Apr 21 20:1
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
963281T_TEF prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00001f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001f00
On node 0 totalpages: 7936
free_area_init_node: node 0, pgdat 802f3830, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 30 pages used for memmap
Normal zone: 3810 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7874
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28088k/31744k available (2409k kernel code, 3656k reserved, 555k data, 120k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 536 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 4096 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 54
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8800100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
initLed: led[0]: Gpio=0xffff8003, FailGpio=0xffff8005
initLed: led[1]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[2]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[3]: Gpio=0xffff800b, FailGpio=0xffff8002
initLed: led[4]: Gpio=0xffff8009, FailGpio=0xffff800a
initLed: led[5]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[6]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[7]: Gpio=0xffff8006, FailGpio=0xffff8007
initLed: led[8]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[9]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[10]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[11]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[12]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[13]: Gpio=0xffff8004, FailGpio=0xffff8008
initLed: led[14]: Gpio=0xffff8006, FailGpio=0xffff8007
initLed: led[15]: Gpio=0xffff801f, FailGpio=0xffff8014
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 21 2011 20:07:12
Broadcom Logger v0.1 Apr 21 2011 20:04:59
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 17
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 120k freed
init started: BusyBox v1.00 (2011.04.21-18:13+0000) multi-call binary
BusyBox v1.00 (2011.04.21-18:13+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
bcmxtmcfg: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 21 2011 20:05:03
ETH Init: 180 tx BDs at 0xa194e000
ETH Init: 400 rx BDs at 0xa19f8000
ETH Init: 400 rx BDs at 0xa19f9000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 30:39:F2:87:8F:41
eth1: MAC Address: 30:39:F2:87:8F:41
eth2: MAC Address: 30:39:F2:87:8F:41
eth3: MAC Address: 30:39:F2:87:8F:41
eth0 Link UP 100 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
BCM63XX_USB USB Device not present
insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Auto-negotiation enabled.
The autonegotiated media type is 100baseTx-FD.
Link is up
mii register 26 is 0x4000
===== Release Version PDG_TEF_SP_4.06L.4 (build timestamp 110421_2011) =====
factoryCfg = 0
iptables v1.4.0: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
sendto: Network is unreachable
ip_tables: (C) 2000-2006 Netfilter Core Team
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
ssk:error:23.000:BcmAdsl_Initialize=0xC00A50D8, g_pFnNotifyCallback=0xC00D5E04
rutDsl_CfgProfileInit:2015:rutDsl_CfgProfileInit()
WLmngr Daemon is running
optarg=0 shmId=0
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
pSdramPHY=0xA1FFFFF8, 0x840002 0x40099
AdslCoreSharedMemInit: shareMemAvailable=484928
AdslCoreHwReset: AdslOemDataAddr = 0xA1F6AEB4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 400 rx BDs at 0xa0bb5000
XTM Init: 100 rx BDs at 0xa0b12000
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (496 buckets, 1984 max)
iptables: No chain/target/match by that name
monitor task is initialized pid= 244
There is no Predefined DevicePin in CFE
WPS Device PIN = 29942275
backup_psi_number_blk=6 result=24576
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
backup_psi_number_blk=6 result=24576
Setting SSID: "ESRO2"
Setting SSID: "wlwl0.1 (): not using net_device_ops yet
0_Guest1"
Setting SSID: "wlwl0.2 (): not using net_device_ops yet
0_Guest2"
Setting SSID: "wlwl0.3 (): not using net_device_ops yet
0_Guest3"
br0: port 5(wl0) entering disabled state
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Undefined error
chanspec 0x2b01 selected
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Reaped 1381
UPnP daemon is ready to run
[/spoiler]