buenas,
Hay un led que debe parpadear mientras el router inicia, el power. El parche tiene mal el nombre:
Index: target/linux/brcm63xx/base-files/lib/brcm63xx.sh
===================================================================
--- target/linux/brcm63xx/base-files/lib/brcm63xx.sh (revisión: 32489)
+++ target/linux/brcm63xx/base-files/lib/brcm63xx.sh (copia de trabajo)
@@ -26,6 +26,10 @@
status_led="963281TAN::power"
ifname=eth0
;;
+ 963281T_TEF)
+ status_led="963281T_TEF::power"
+ ifname=eth0
+ ;;
en la definición de leds lo llamaste 963281T_TEF:green:power
Adjunto el log del fw original. Hay una cosa común a los broadcom con el driver propietario y es este mensaje:
[spoiler]wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2[/spoiler]
la verdad es que el router tiene una partición nvram, y por un momento pensé que como los soc 47xx cogen la srom de ahí, pero por el contenido parecen dos copias de la configuración del router con el fw original...

Saludos
BOOTLOG[spoiler]CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.10
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : run.bin
Default host flash file name : 2.bin
Boot delay (0-9 seconds) : 9
Board Id (0-4) : 963281T_TEF
Number of MAC Addresses (1-32) : 11
Base MAC Address : 30:39:f2:87:8f:41
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 1
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 9
web info: Waiting for connection on socket 0.
web info: Waiting for connection on socket 1.
web info: Waiting for connection on socket 2.
web info: Waiting for connection on socket 0.
web info: Waiting for connection on socket 1.
web info: Upload 6818609 bytes, Broadcom image format.
web info: Waiting for connection on socket 0.
Flashing root file system and kernel at 0xb8800000: .....................................................
.
*** Image flash done *** !
Resetting board...HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.10
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : run.bin
Default host flash file name : 2.bin
Boot delay (0-9 seconds) : 9
Boot image (0=latest, 1=previous) : 0
Board Id (0-4) : 963281T_TEF
Number of MAC Addresses (1-32) : 11
Base MAC Address : 30:39:f2:87:8f:41
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 1
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Booting from latest image (0xb8800000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (zu1costast@thorold) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Thu Apr 21 20:1
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
963281T_TEF prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00001f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001f00
On node 0 totalpages: 7936
free_area_init_node: node 0, pgdat 802f3830, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 30 pages used for memmap
Normal zone: 3810 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7874
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28088k/31744k available (2409k kernel code, 3656k reserved, 555k data, 120k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 536 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 4096 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 54
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8800100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
initLed: led[0]: Gpio=0xffff8003, FailGpio=0xffff8005
initLed: led[1]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[2]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[3]: Gpio=0xffff800b, FailGpio=0xffff8002
initLed: led[4]: Gpio=0xffff8009, FailGpio=0xffff800a
initLed: led[5]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[6]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[7]: Gpio=0xffff8006, FailGpio=0xffff8007
initLed: led[8]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[9]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[10]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[11]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[12]: Gpio=0xffffffff, FailGpio=0xffffffff
initLed: led[13]: Gpio=0xffff8004, FailGpio=0xffff8008
initLed: led[14]: Gpio=0xffff8006, FailGpio=0xffff8007
initLed: led[15]: Gpio=0xffff801f, FailGpio=0xffff8014
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 21 2011 20:07:12
Broadcom Logger v0.1 Apr 21 2011 20:04:59
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 17
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 120k freed
init started: BusyBox v1.00 (2011.04.21-18:13+0000) multi-call binary
BusyBox v1.00 (2011.04.21-18:13+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
bcmxtmcfg: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 21 2011 20:05:03
ETH Init: 180 tx BDs at 0xa194e000
ETH Init: 400 rx BDs at 0xa19f8000
ETH Init: 400 rx BDs at 0xa19f9000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 30:39:F2:87:8F:41
eth1: MAC Address: 30:39:F2:87:8F:41
eth2: MAC Address: 30:39:F2:87:8F:41
eth3: MAC Address: 30:39:F2:87:8F:41
eth0 Link UP 100 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
BCM63XX_USB USB Device not present
insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Auto-negotiation enabled.
The autonegotiated media type is 100baseTx-FD.
Link is up
mii register 26 is 0x4000
===== Release Version PDG_TEF_SP_4.06L.4 (build timestamp 110421_2011) =====
factoryCfg = 0
iptables v1.4.0: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
sendto: Network is unreachable
ip_tables: (C) 2000-2006 Netfilter Core Team
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
ssk:error:23.000:BcmAdsl_Initialize=0xC00A50D8, g_pFnNotifyCallback=0xC00D5E04
rutDsl_CfgProfileInit:2015:rutDsl_CfgProfileInit()
WLmngr Daemon is running
optarg=0 shmId=0
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
pSdramPHY=0xA1FFFFF8, 0x840002 0x40099
AdslCoreSharedMemInit: shareMemAvailable=484928
AdslCoreHwReset: AdslOemDataAddr = 0xA1F6AEB4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 400 rx BDs at 0xa0bb5000
XTM Init: 100 rx BDs at 0xa0b12000
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (496 buckets, 1984 max)
iptables: No chain/target/match by that name
monitor task is initialized pid= 244
There is no Predefined DevicePin in CFE
WPS Device PIN = 29942275
backup_psi_number_blk=6 result=24576
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
backup_psi_number_blk=6 result=24576
Setting SSID: "ESRO2"
Setting SSID: "wlwl0.1 (): not using net_device_ops yet
0_Guest1"
Setting SSID: "wlwl0.2 (): not using net_device_ops yet
0_Guest2"
Setting SSID: "wlwl0.3 (): not using net_device_ops yet
0_Guest3"
br0: port 5(wl0) entering disabled state
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Undefined error
chanspec 0x2b01 selected
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Reaped 1381
UPnP daemon is ready to run
[/spoiler]