Que alguien con un ralink pruebe el siguiente firmware:
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32910.bin
Probad lo del reinicio y adjuntad un bootlog (dmesg) y un "cat /etc/config/wireless"
Saludos.
Primer inicio, conectado correctamente en modo cliente:
[spoiler=dmesg]
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Jul 31 13:39:53 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f890, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61876k/65536k available (2225k kernel code, 3660k reserved, 397k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.464000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.164000] eth0: link forced UP - 100/full - flow control off/off
[ 3.384000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.452000] There is already a switch registered on the device 'eth0'
[ 5.916000] Button Hotplug driver version 0.4.1
[ 12.740000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.748000] Backport based on wireless-testing.git master-2012-07-16
[ 12.756000] compat.git: wireless-testing.git
[ 12.824000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.828000] cfg80211: World regulatory domain updated:
[ 12.836000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.844000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.852000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.860000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.868000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.876000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.316000] NET: Registered protocol family 10
[ 13.772000] SCSI subsystem initialized
[ 13.864000] There is already a switch registered on the device 'eth0'
[ 14.220000] usbcore: registered new interface driver usbfs
[ 14.224000] usbcore: registered new interface driver hub
[ 14.232000] usbcore: registered new device driver usb
[ 15.380000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.388000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.572000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.572000] Registered led device: rt2800pci-phy0::radio
[ 15.572000] Registered led device: rt2800pci-phy0::assoc
[ 15.576000] Registered led device: rt2800pci-phy0::quality
[ 15.920000] PPP generic driver version 2.4.2
[ 16.308000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.596000] NET: Registered protocol family 24
[ 16.792000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.904000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 16.908000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 16.944000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 16.960000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 16.968000] hub 1-0:1.0: USB hub found
[ 16.972000] hub 1-0:1.0: 2 ports detected
[ 17.152000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
[ 17.944000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.356000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.464000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.468000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.476000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.544000] hub 2-0:1.0: USB hub found
[ 18.548000] hub 2-0:1.0: 1 port detected
[ 18.720000] Initializing USB Mass Storage driver...
[ 18.728000] usbcore: registered new interface driver usb-storage
[ 18.732000] USB Mass Storage support registered.
[ 18.768000] usbcore: registered new interface driver ums-alauda
[ 18.808000] usbcore: registered new interface driver ums-cypress
[ 18.844000] usbcore: registered new interface driver ums-datafab
[ 18.880000] usbcore: registered new interface driver ums-freecom
[ 18.916000] usbcore: registered new interface driver ums-isd200
[ 18.956000] usbcore: registered new interface driver ums-jumpshot
[ 18.992000] usbcore: registered new interface driver ums-karma
[ 19.028000] usbcore: registered new interface driver ums-sddr09
[ 19.064000] usbcore: registered new interface driver ums-sddr55
[ 19.104000] usbcore: registered new interface driver ums-usbat
[ 19.140000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 24.800000] eth0: link forced UP - 100/full - flow control off/off
[ 24.812000] device eth0 entered promiscuous mode
[ 24.820000] br-lan: port 1(eth0) entered forwarding state
[ 24.828000] br-lan: port 1(eth0) entered forwarding state
[ 26.828000] br-lan: port 1(eth0) entered forwarding state
[ 46.224000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 46.236000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 46.240000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 93.208000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 95.496000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 97.776000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 105.296000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 109.236000] done.
[ 109.240000] JFFS2 notice: (1064) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 127.800000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 158.196000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 162.240000] wlan0: authenticate with 00:19:70:XX:XX:XX
[ 162.288000] wlan0: send auth to 00:19:70:XX:XX:XX (try 1/3)
[ 162.296000] wlan0: authenticated
[ 162.332000] wlan0: associate with 00:19:70:XX:XX:XX (try 1/3)
[ 162.344000] wlan0: RX AssocResp from 00:19:70:XX:XX:XX (capab=0x431 status=0 aid=1)
[ 162.352000] wlan0: associated
[ 162.356000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 220.140000] br-lan: port 1(eth0) entered disabled state
[ 220.184000] device eth0 left promiscuous mode
[ 220.188000] br-lan: port 1(eth0) entered disabled state
[ 220.224000] eth0: link forced UP - 100/full - flow control off/off
[ 220.272000] device eth0 entered promiscuous mode
[ 220.300000] br-lan: port 1(eth0) entered forwarding state
[ 220.304000] br-lan: port 1(eth0) entered forwarding state
[ 221.924000] wlan0: deauthenticating from 00:19:70:XX:XX:XX by local choice (reason=3)
[ 222.308000] br-lan: port 1(eth0) entered forwarding state
[ 223.532000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 227.104000] wlan0: authenticate with 00:19:70:XX:XX:XX
[ 227.156000] wlan0: send auth to 00:19:70:XX:XX:XX (try 1/3)
[ 227.164000] wlan0: authenticated
[ 227.204000] wlan0: associate with 00:19:70:XX:XX:XX (try 1/3)
[ 227.216000] wlan0: RX AssocResp from 00:19:70:XX:XX:XX (capab=0x431 status=0 aid=1)
[ 227.224000] wlan0: associated
[ 227.228000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[/spoiler]
[spoiler=cat /etc/config/wireless]
config wifi-device 'radio0'
option type 'mac80211'
option macaddr 'c6:a2:77:XX:XX:XX'
option hwmode '11ng'
option htmode 'HT20'
list ht_capab 'GF'
list ht_capab 'SHORT-GI-20'
list ht_capab 'SHORT-GI-40'
list ht_capab 'TX-STBC'
list ht_capab 'RX-STBC12'
option disabled '0'
option channel '8'
option country '00'
config wifi-iface
option network 'wwan'
option ssid 'WIFI'
option encryption 'psk2'
option device 'radio0'
option mode 'sta'
option bssid '00:19:70:XX:XX:XX'
option key '1234567890'
[/spoiler]
Despues de un reboot:
[spoiler=dmesg]
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Jul 31 13:39:53 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f890, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61876k/65536k available (2225k kernel code, 3660k reserved, 397k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.464000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.196000] eth0: link forced UP - 100/full - flow control off/off
[ 3.416000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.480000] There is already a switch registered on the device 'eth0'
[ 5.944000] Button Hotplug driver version 0.4.1
[ 9.944000] JFFS2 notice: (337) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[ 12.912000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.920000] Backport based on wireless-testing.git master-2012-07-16
[ 12.928000] compat.git: wireless-testing.git
[ 12.992000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.996000] cfg80211: World regulatory domain updated:
[ 13.004000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.012000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.020000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.028000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.036000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.044000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.488000] NET: Registered protocol family 10
[ 13.940000] SCSI subsystem initialized
[ 14.032000] There is already a switch registered on the device 'eth0'
[ 14.388000] usbcore: registered new interface driver usbfs
[ 14.396000] usbcore: registered new interface driver hub
[ 14.404000] usbcore: registered new device driver usb
[ 15.548000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.556000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.740000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.740000] Registered led device: rt2800pci-phy0::radio
[ 15.740000] Registered led device: rt2800pci-phy0::assoc
[ 15.740000] Registered led device: rt2800pci-phy0::quality
[ 16.092000] PPP generic driver version 2.4.2
[ 16.480000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.768000] NET: Registered protocol family 24
[ 16.968000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.076000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.080000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.116000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.132000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.140000] hub 1-0:1.0: USB hub found
[ 17.144000] hub 1-0:1.0: 2 ports detected
[ 17.324000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
[ 18.116000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.528000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.636000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.640000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.648000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.716000] hub 2-0:1.0: USB hub found
[ 18.720000] hub 2-0:1.0: 1 port detected
[ 18.896000] Initializing USB Mass Storage driver...
[ 18.900000] usbcore: registered new interface driver usb-storage
[ 18.904000] USB Mass Storage support registered.
[ 18.940000] usbcore: registered new interface driver ums-alauda
[ 18.980000] usbcore: registered new interface driver ums-cypress
[ 19.016000] usbcore: registered new interface driver ums-datafab
[ 19.052000] usbcore: registered new interface driver ums-freecom
[ 19.092000] usbcore: registered new interface driver ums-isd200
[ 19.128000] usbcore: registered new interface driver ums-jumpshot
[ 19.164000] usbcore: registered new interface driver ums-karma
[ 19.200000] usbcore: registered new interface driver ums-sddr09
[ 19.240000] usbcore: registered new interface driver ums-sddr55
[ 19.276000] usbcore: registered new interface driver ums-usbat
[ 19.316000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 24.736000] eth0: link forced UP - 100/full - flow control off/off
[ 24.760000] device eth0 entered promiscuous mode
[ 24.776000] br-lan: port 1(eth0) entered forwarding state
[ 24.780000] br-lan: port 1(eth0) entered forwarding state
[ 26.784000] br-lan: port 1(eth0) entered forwarding state
[/spoiler]
[spoiler=cat /etc/config/wireless]
config wifi-device 'radio0'
option type 'mac80211'
option macaddr 'c6:a2:77:XX:XX:XX'
option hwmode '11ng'
option htmode 'HT20'
list ht_capab 'GF'
list ht_capab 'SHORT-GI-20'
list ht_capab 'SHORT-GI-40'
list ht_capab 'TX-STBC'
list ht_capab 'RX-STBC12'
option disabled '0'
option channel '8'
option country '00'
config wifi-iface
option network 'wwan'
option ssid 'WIFI'
option encryption 'psk2'
option device 'radio0'
option mode 'sta'
option bssid '00:19:70:XX:XX:XX'
option key '1234567890'
config wifi-device radio1
option type mac80211
option channel 11
option macaddr 72:25:2b:XX:XX:XX
option hwmode 11ng
option htmode HT20
list ht_capab GF
list ht_capab SHORT-GI-20
list ht_capab SHORT-GI-40
list ht_capab TX-STBC
list ht_capab RX-STBC12
# REMOVE THIS LINE TO ENABLE WIFI:
option disabled 1
config wifi-iface
option device radio1
option network lan
option mode ap
option ssid OpenWrt
option encryption none
[/spoiler]