Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a (Leído 2125599 veces)

emeryth · « **Respuesta #520 en:** 20-07-2012, 17:45 (Viernes) »

hola Noltari, e probado los caldata, al probar el primero apareció la wifi, pero sin tipo de red y una potencia de 27 dB y realizaba escaneo pero no se activaba como AP. Asi que intente con los otros caldatas pero la wifi desapareció, y al intentar volver a la primera caldata ya no apareció la wifi.

muchisimas gracias por tu esfuerzo y ayuda.

Noltari · « **Respuesta #521 en:** 20-07-2012, 18:53 (Viernes) »

Cita de: emeryth en 20-07-2012, 17:45 (Viernes)

hola Noltari, e probado los caldata, al probar el primero apareció la wifi, pero sin tipo de red y una potencia de 27 dB y realizaba escaneo pero no se activaba como AP. Asi que intente con los otros caldatas pero la wifi desapareció, y al intentar volver a la primera caldata ya no apareció la wifi.

muchisimas gracias por tu esfuerzo y ayuda.

Lo del primer intento suena prometedor.

Realiza lo siguiente:
Imagino que tienes instalado el último firmware que te he pasado. Si es así copia el primer archivo a la partición mtd4.
Una vez lo hayas copiado a la partición mtd4, ejecuta el siguiente comando:

Código: [Seleccionar]

mtd -r erase rootfs_dataEse comando debería reiniciar el router. Una vez que el router se haya reiniciado, haz un dmesg y mándamelo.

EDIT: parece ser que a Ggarza también le ha vuelto el wifi con el primero.
Una vez flasheado el primer caldata (si no habéis flasheado otro encima no hace falta que lo repitáis).
Borrad los datos de la partición rootfs_data como indico arriba o volved a flashear el mismo firmware o uno oficial.

Saludos.

emeryth · « **Respuesta #522 en:** 20-07-2012, 20:04 (Viernes) »

cuando reinicia el router no tiene ping, no responde al ssh ni html, lo curioso es que tengo internet.
así que no tengo manera de sacar el dmesg, instalo otra ves tu ultimo firmware? y saco el dmesg?

Noltari · « **Respuesta #523 en:** 20-07-2012, 20:25 (Viernes) »

Cita de: emeryth en 20-07-2012, 20:04 (Viernes)

cuando reinicia el router no tiene ping, no responde al ssh ni html, lo curioso es que tengo internet.
así que no tengo manera de sacar el dmesg, instalo otra ves tu ultimo firmware? y saco el dmesg?

Si lo tienes conectado por ethernet a otro router con la ip 192.168.1.1 es normal. El tema es que el comando que te he dado reinicia toda la configuracion.

Fija la ip de tu pc manualmente, sin dhcp.

Saludos

emeryth · « **Respuesta #524 en:** 20-07-2012, 20:48 (Viernes) »

pues si, que tonto soy, lamentablemente aun no aparece el wifi te mando el dmesg

[spoiler][ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu Jul 19 20:53:42 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] pci 0000:00:01.0: fixup device configuration
[ 0.200000] PCI: CLS 0 bytes, default 16
[ 0.204000] audit: initializing netlink socket (disabled)
[ 0.212000] type=2000 audit(0.212:1): initialized
[ 0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.236000] msgmni has been set to 120
[ 0.240000] io scheduler noop registered
[ 0.244000] io scheduler deadline registered (default)
[ 0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.260000] console [ttyS0] enabled, bootconsole disabled
[ 0.276000] physmap platform flash device: 02000000 at 1e000000
[ 0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.300000] Amd/Fujitsu Extended Query version 1.3.
[ 0.304000] number of CFI chips: 1
[ 0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.336000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length de0000
[ 0.360000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.368000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.380000] 0x000000000000-0x000000020000 : "CFE"
[ 0.388000] 0x000000020100-0x000000120000 : "kernel"
[ 0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.408000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.420000] mtd: partition "rootfs" set to be root filesystem
[ 0.424000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.432000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.444000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.460000] 0x000000020000-0x000000e00000 : "linux"
[ 0.480000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.488000] Registered led device: HW556:red:message
[ 0.488000] Registered led device: HW556:red:hspa
[ 0.492000] Registered led device: HW556:red:dsl
[ 0.492000] Registered led device: HW556:red:power
[ 0.492000] Registered led device: HW556:red:all
[ 0.492000] TCP cubic registered
[ 0.496000] NET: Registered protocol family 17
[ 0.500000] 8021q: 802.1Q VLAN Support v1.8
[ 0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.524000] Freeing unused kernel memory: 200k freed
[ 3.228000] eth0: link forced UP - 100/full - flow control off/off
[ 3.444000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.512000] There is already a switch registered on the device 'eth0'
[ 5.980000] Button Hotplug driver version 0.4.1
[ 9.960000] JFFS2 notice: (347) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 15.112000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 15.120000] Backport based on wireless-testing.git master-2012-07-16
[ 15.128000] compat.git: wireless-testing.git
[ 15.192000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.196000] cfg80211: World regulatory domain updated:
[ 15.204000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.212000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.220000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.228000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.236000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.244000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.100000] NET: Registered protocol family 10
[ 17.116000] SCSI subsystem initialized
[ 17.216000] There is already a switch registered on the device 'eth0'
[ 17.584000] usbcore: registered new interface driver usbfs
[ 17.588000] usbcore: registered new interface driver hub
[ 17.596000] usbcore: registered new device driver usb
[ 20.076000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 20.088000] ath: phy0: Bad EEPROM checksum 0xe09c or revision 0x000e
[ 20.096000] ath: phy0: Unable to initialize hardware; initialization status: -22
[ 20.104000] ath9k 0000:00:01.0: Failed to initialize device
[ 20.112000] ath9k: probe of 0000:00:01.0 failed with error -22
[ 20.496000] PPP generic driver version 2.4.2
[ 20.888000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.180000] NET: Registered protocol family 24
[ 21.396000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 21.508000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 21.512000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 21.548000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 21.564000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 21.572000] hub 1-0:1.0: USB hub found
[ 21.576000] hub 1-0:1.0: 2 ports detected
[ 21.756000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 22.140000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[ 22.380000] hub 1-1:1.0: USB hub found
[ 22.392000] hub 1-1:1.0: 2 ports detected
[ 22.588000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 23.004000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 23.116000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 23.120000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 23.128000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 23.196000] hub 2-0:1.0: USB hub found
[ 23.200000] hub 2-0:1.0: 1 port detected
[ 23.376000] Initializing USB Mass Storage driver...
[ 23.380000] usbcore: registered new interface driver usb-storage
[ 23.388000] USB Mass Storage support registered.
[ 23.424000] usbcore: registered new interface driver ums-alauda
[ 23.460000] usbcore: registered new interface driver ums-cypress
[ 23.496000] usbcore: registered new interface driver ums-datafab
[ 23.536000] usbcore: registered new interface driver ums-freecom
[ 23.572000] usbcore: registered new interface driver ums-isd200
[ 23.608000] usbcore: registered new interface driver ums-jumpshot
[ 23.648000] usbcore: registered new interface driver ums-karma
[ 23.684000] usbcore: registered new interface driver ums-sddr09
[ 23.724000] usbcore: registered new interface driver ums-sddr55
[ 23.760000] usbcore: registered new interface driver ums-usbat
[ 23.800000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 30.440000] eth0: link forced UP - 100/full - flow control off/off
[ 30.456000] device eth0 entered promiscuous mode
[ 30.464000] br-lan: port 1(eth0) entered forwarding state
[ 30.468000] br-lan: port 1(eth0) entered forwarding state
[ 32.472000] br-lan: port 1(eth0) entered forwarding state
[/spoiler]

gracias

tool · « **Respuesta #525 en:** 20-07-2012, 21:11 (Viernes) »

Noltari podrías resubir las compilaciones para Ralink?

Noltari · « **Respuesta #526 en:** 21-07-2012, 02:09 (Sábado) »

Parches actualizados, volviendo a la detección utilizada por danitool:
https://dl.dropbox.com/u/4708147/openwrt/hw556/hw556_svn_all.patch

Código: [Seleccionar]

patch -p0 -i hw556_svn_all.patch
He optado por proteger a lo "bestia" los 2MB últimos de la flash, para evitar borrar datos de calibración en cualquier dispositivo.
Creo que con una flash de 16MB - 2MB = 14MB deberían ser más que suficientes

.

Firmware actualizado:
https://dl.dropbox.com/u/4708147/openwrt/hw556/openwrt-HW556-squashfs-cfe_r32786.bin

Como comprenderéis, por seguridad me veo obligado a retirar completamente los enlaces de las compilaciones anteriores por si las moscas.

Un saludo y pido disculpas por las molestias ocasionadas.

P.D: Ggarza ya tiene wifi, aún estoy en ello con emeryth. ¿Alguno más que se haya quedado sin wifi?

tool · « **Respuesta #527 en:** 21-07-2012, 11:23 (Sábado) »

Gracias Noltari, pero está bien avisado en el post principal, Backup primero.

Cuánto se está perdiendo entre reservar o no esos 2mb?

En el caso de los ralink que tienes que inyectar los datos de calibración desde un fichero, no se "pierden esos 2mb" ?

Pruebo la build y te cuento.

Porque la anterior que tenía, no iba el modo cliente al reiniciarlo, tenía que volver a dejarlo de fábrica y volver a crear el modo cliente.

No tienes por qué pedir disculpas, que os estáis llevando un currele

jar229 · « **Respuesta #528 en:** 21-07-2012, 12:03 (Sábado) »

Creo que se está refiriendo a reservar 2 de los 16 megas de la flash para guardar los datos de la wifi

Una estupenda idea

Noltari · « **Respuesta #529 en:** 21-07-2012, 12:05 (Sábado) »

Cita de: tool en 21-07-2012, 11:23 (Sábado)

Gracias Noltari, pero está bien avisado en el post principal, Backup primero.

Cuánto se está perdiendo entre reservar o no esos 2mb?

En el caso de los ralink que tienes que inyectar los datos de calibración desde un fichero, no se "pierden esos 2mb" ?

Pruebo la build y te cuento.

Porque la anterior que tenía, no iba el modo cliente al reiniciarlo, tenía que volver a dejarlo de fábrica y volver a crear el modo cliente.

No tienes por qué pedir disculpas, que os estáis llevando un currele

Simplemente es una cuestión de espacio. Al proteger los dos últimos megas de la flash, nos quedamos con 14 MB de espacio para el firmware y almacenamiento de archivos y paquetes/programas. Creo que es más que suficiente de todas formas

.

En el caso del ralink estamos reservando los 2 megas para nada, porque se podrían usar perfectamente. El problema es que no es aconsejable hacer un firmware distinto para cada router porque siempre hay alguno que se pone a probar firmwares y la lía :$...

Lo del modo cliente ni idea tío, cada driver va como le sale de los h*****, es una locura xDDD...

Noltari · « **Respuesta #530 en:** 21-07-2012, 13:47 (Sábado) »

Restaurado el wifi de emeryth utilizando los datos de calibración del MX29GL128EH de jar229.

Por cierto, para restaurar los datos de calibración correctamente ha sido necesario utilizar el comando:
mtd -r erase cal_data
Este comando borra completamente la partición de los datos de calibración.

Si no se ejecuta este comando antes de restaurar los datos del wifi (dd if=ath.bin of=/dev/mtd4), no se graban correctamente los datos y se producen errores al comprobar el checksum de estos.

P.D: El primer firmware del post principal es el más actualizado y es seguro utilizarlo en cualquier router.

Saludos.

jar229 · « **Respuesta #531 en:** 21-07-2012, 18:00 (Sábado) »

Así todo el mundo tiene ya wifi ?

Noltari · « **Respuesta #532 en:** 21-07-2012, 18:02 (Sábado) »

Cita de: jar229 en 21-07-2012, 18:00 (Sábado)

Así todo el mundo tiene ya wifi ?

Sí, todo el mundo tiene wifi

.

Saludos.

tool · « **Respuesta #533 en:** 21-07-2012, 20:11 (Sábado) »

Cita de: jar229 en 21-07-2012, 12:03 (Sábado)

Creo que se está refiriendo a reservar 2 de los 16 megas de la flash para guardar los datos de la wifi
Una estupenda idea

Si, sé para que son esos 2mb, pero en el caso de ralink no hacen falta

Y lo de reservar 2mb, creo yo, entiendo que es la posible zona por dónde estén los datos. Porque no creo que ocupen 2mb la calibración.

Voy a probar si ahora va OK el wifi.

EDIT:

Pruebas: Me pongo como cliente sin problemas y funciona (RALINK).
APago y vuelvo a encender, no se enciende el wifi, y en dónde debería aparecer el wifi como cliente, aparece radio1, con OpenWRT master (todo como desconectado :p)
Si enchufo de nuevo, creo que creaba radio2 etc.

Aquí va el dmesg.
[spoiler=DMESG RALINK 2nd boot][ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.160000] eth0: link forced UP - 100/full - flow control off/off
[ 3.380000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.444000] There is already a switch registered on the device 'eth0'
[ 5.912000] Button Hotplug driver version 0.4.1
[ 9.920000] JFFS2 notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[ 12.900000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.908000] Backport based on wireless-testing.git master-2012-07-16
[ 12.912000] compat.git: wireless-testing.git
[ 12.980000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.984000] cfg80211: World regulatory domain updated:
[ 12.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.008000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.016000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.024000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.032000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.472000] NET: Registered protocol family 10
[ 13.928000] SCSI subsystem initialized
[ 14.020000] There is already a switch registered on the device 'eth0'
[ 14.380000] usbcore: registered new interface driver usbfs
[ 14.384000] usbcore: registered new interface driver hub
[ 14.392000] usbcore: registered new device driver usb
[ 15.544000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.552000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.732000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.736000] Registered led device: rt2800pci-phy0::radio
[ 15.736000] Registered led device: rt2800pci-phy0::assoc
[ 15.736000] Registered led device: rt2800pci-phy0::quality
[ 16.084000] PPP generic driver version 2.4.2
[ 16.476000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.768000] NET: Registered protocol family 24
[ 16.968000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.080000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.084000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.120000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.136000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.144000] hub 1-0:1.0: USB hub found
[ 17.148000] hub 1-0:1.0: 2 ports detected
[ 17.328000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 17.708000] usb 1-2: new high-speed USB device number 2 using bcm63xx_ehci
[ 17.856000] hub 1-2:1.0: USB hub found
[ 17.864000] hub 1-2:1.0: 4 ports detected
[ 18.156000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.572000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.684000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.688000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.696000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.764000] hub 2-0:1.0: USB hub found
[ 18.768000] hub 2-0:1.0: 1 port detected
[ 18.944000] Initializing USB Mass Storage driver...
[ 18.948000] usbcore: registered new interface driver usb-storage
[ 18.956000] USB Mass Storage support registered.
[ 18.992000] usbcore: registered new interface driver ums-alauda
[ 19.028000] usbcore: registered new interface driver ums-cypress
[ 19.068000] usbcore: registered new interface driver ums-datafab
[ 19.104000] usbcore: registered new interface driver ums-freecom
[ 19.140000] usbcore: registered new interface driver ums-isd200
[ 19.180000] usbcore: registered new interface driver ums-jumpshot
[ 19.216000] usbcore: registered new interface driver ums-karma
[ 19.256000] usbcore: registered new interface driver ums-sddr09
[ 19.292000] usbcore: registered new interface driver ums-sddr55
[ 19.328000] usbcore: registered new interface driver ums-usbat
[ 19.368000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 24.936000] eth0: link forced UP - 100/full - flow control off/off
[ 24.948000] device eth0 entered promiscuous mode
[ 24.956000] br-lan: port 1(eth0) entered forwarding state
[ 24.960000] br-lan: port 1(eth0) entered forwarding state
[ 26.964000] br-lan: port 1(eth0) entered forwarding state
[ 223.628000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 225.844000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 228.056000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 238.736000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 240.952000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 243.168000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 247.816000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 250.032000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 252.252000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready[/spoiler]

Noltari · « **Respuesta #534 en:** 21-07-2012, 20:47 (Sábado) »

Cita de: tool en 21-07-2012, 20:11 (Sábado)

Cita de: jar229 en 21-07-2012, 12:03 (Sábado)
Creo que se está refiriendo a reservar 2 de los 16 megas de la flash para guardar los datos de la wifi
Una estupenda idea

Si, sé para que son esos 2mb, pero en el caso de ralink no hacen falta Y lo de reservar 2mb, creo yo, entiendo que es la posible zona por dónde estén los datos. Porque no creo que ocupen 2mb la calibración.

Voy a probar si ahora va OK el wifi.

EDIT:

Pruebas: Me pongo como cliente sin problemas y funciona (RALINK).
APago y vuelvo a encender, no se enciende el wifi, y en dónde debería aparecer el wifi como cliente, aparece radio1, con OpenWRT master (todo como desconectado :p)
Si enchufo de nuevo, creo que creaba radio2 etc.

Aquí va el dmesg.
[spoiler=DMESG RALINK 2nd boot][ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.160000] eth0: link forced UP - 100/full - flow control off/off
[ 3.380000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.444000] There is already a switch registered on the device 'eth0'
[ 5.912000] Button Hotplug driver version 0.4.1
[ 9.920000] JFFS2 notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[ 12.900000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.908000] Backport based on wireless-testing.git master-2012-07-16
[ 12.912000] compat.git: wireless-testing.git
[ 12.980000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.984000] cfg80211: World regulatory domain updated:
[ 12.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.008000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.016000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.024000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.032000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.472000] NET: Registered protocol family 10
[ 13.928000] SCSI subsystem initialized
[ 14.020000] There is already a switch registered on the device 'eth0'
[ 14.380000] usbcore: registered new interface driver usbfs
[ 14.384000] usbcore: registered new interface driver hub
[ 14.392000] usbcore: registered new device driver usb
[ 15.544000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.552000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.732000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.736000] Registered led device: rt2800pci-phy0::radio
[ 15.736000] Registered led device: rt2800pci-phy0::assoc
[ 15.736000] Registered led device: rt2800pci-phy0::quality
[ 16.084000] PPP generic driver version 2.4.2
[ 16.476000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.768000] NET: Registered protocol family 24
[ 16.968000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.080000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.084000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.120000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.136000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.144000] hub 1-0:1.0: USB hub found
[ 17.148000] hub 1-0:1.0: 2 ports detected
[ 17.328000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 17.708000] usb 1-2: new high-speed USB device number 2 using bcm63xx_ehci
[ 17.856000] hub 1-2:1.0: USB hub found
[ 17.864000] hub 1-2:1.0: 4 ports detected
[ 18.156000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.572000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.684000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.688000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.696000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.764000] hub 2-0:1.0: USB hub found
[ 18.768000] hub 2-0:1.0: 1 port detected
[ 18.944000] Initializing USB Mass Storage driver...
[ 18.948000] usbcore: registered new interface driver usb-storage
[ 18.956000] USB Mass Storage support registered.
[ 18.992000] usbcore: registered new interface driver ums-alauda
[ 19.028000] usbcore: registered new interface driver ums-cypress
[ 19.068000] usbcore: registered new interface driver ums-datafab
[ 19.104000] usbcore: registered new interface driver ums-freecom
[ 19.140000] usbcore: registered new interface driver ums-isd200
[ 19.180000] usbcore: registered new interface driver ums-jumpshot
[ 19.216000] usbcore: registered new interface driver ums-karma
[ 19.256000] usbcore: registered new interface driver ums-sddr09
[ 19.292000] usbcore: registered new interface driver ums-sddr55
[ 19.328000] usbcore: registered new interface driver ums-usbat
[ 19.368000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 24.936000] eth0: link forced UP - 100/full - flow control off/off
[ 24.948000] device eth0 entered promiscuous mode
[ 24.956000] br-lan: port 1(eth0) entered forwarding state
[ 24.960000] br-lan: port 1(eth0) entered forwarding state
[ 26.964000] br-lan: port 1(eth0) entered forwarding state
[ 223.628000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 225.844000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 228.056000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 238.736000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 240.952000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 243.168000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 247.816000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 250.032000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 252.252000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready[/spoiler]

Podría ser un problema del driver del ralink :$...

Ya he dicho que en los ralink no sirve de nada. El problema es que no tenemos ningún método para identificar correctamente si el router es un ralink o un atheros.

Cita de: Noltari

En el caso del ralink estamos reservando los 2 megas para nada, porque se podrían usar perfectamente. El problema es que no es aconsejable hacer un firmware distinto para cada router porque siempre hay alguno que se pone a probar firmwares y la lía :$...

Sobre lo del tamaño a reservar no depende de mi. El problema es que si unos datos están en el offset 0xEFE000 y otros en el 0xF7E000. Como mínimo se podría reservar los últimos 0x102000 bytes de la flash (algo más de un mega). De esta forma, aunque los datos del wifi ocupen 0x2000, el espacio posterior no se puede utilizar dado que no es contiguo al anterior. Se podría utilizar, pero para crear una partición a la que no creo que le dieras uso.

Saludos.

geminis_demon · « **Respuesta #535 en:** 22-07-2012, 22:05 (Domingo) »

Cita de: tool en 21-07-2012, 20:11 (Sábado)

Pruebas: Me pongo como cliente sin problemas y funciona (RALINK).
APago y vuelvo a encender, no se enciende el wifi, y en dónde debería aparecer el wifi como cliente, aparece radio1, con OpenWRT master (todo como desconectado :p)
Si enchufo de nuevo, creo que creaba radio2 etc.

Me pasa exactamente lo mismo, tengo que mantenerlo encendido siempre porque como lo reinicie me quedo sin wifi y tengo que volver a flashear.

Me tambien me pasaba lo mismo con la compilación anterior "openwrt-HW556-squashfs-cfe_r32764.bin"

tool · « **Respuesta #536 en:** 23-07-2012, 02:00 (Lunes) »

No hace falta volver a flashear, con restaurar valores de fábrica y volver a configurar listo.

Es una jodienda, tenía uno configurado como cliente para una xbox en la misma regleta. Al apagar regleta adiós, toca enchufar el portátil y reconfigurar.

A ver si conseguimos arreglar esto!

Noltari · « **Respuesta #537 en:** 23-07-2012, 02:14 (Lunes) »

Cita de: tool en 23-07-2012, 02:00 (Lunes)

No hace falta volver a flashear, con restaurar valores de fábrica y volver a configurar listo.

Es una jodienda, tenía uno configurado como cliente para una xbox en la misma regleta. Al apagar regleta adiós, toca enchufar el portátil y reconfigurar.

A ver si conseguimos arreglar esto!

Haz un backup de la configuración por LuCI con todo funcionando y otro al reiniciar.
Súbelos al foro y mañana (hoy) le echo un ojo.

Si puedes poner dmesg del primer inicio y del reinicio ayudaría también.

Saludos.

tool · « **Respuesta #538 en:** 25-07-2012, 11:24 (Miércoles) »

Perdón por tardar, pero no he tenido tiempo.
Aquí dejo dmesg primer boot configurado y funcionando client mode.
[spoiler=DMESG 1º Boot]
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.168000] eth0: link forced UP - 100/full - flow control off/off
[ 3.388000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.452000] There is already a switch registered on the device 'eth0'
[ 5.920000] Button Hotplug driver version 0.4.1
[ 9.884000] JFFS2 notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 15.024000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 15.032000] Backport based on wireless-testing.git master-2012-07-16
[ 15.040000] compat.git: wireless-testing.git
[ 15.104000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.108000] cfg80211: World regulatory domain updated:
[ 15.116000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.124000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.132000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.140000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.148000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.156000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.968000] NET: Registered protocol family 10
[ 16.440000] SCSI subsystem initialized
[ 16.532000] There is already a switch registered on the device 'eth0'
[ 16.888000] usbcore: registered new interface driver usbfs
[ 16.896000] usbcore: registered new interface driver hub
[ 16.908000] usbcore: registered new device driver usb
[ 18.616000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 18.624000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 18.808000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.808000] Registered led device: rt2800pci-phy0::radio
[ 18.812000] Registered led device: rt2800pci-phy0::assoc
[ 18.812000] Registered led device: rt2800pci-phy0::quality
[ 19.160000] PPP generic driver version 2.4.2
[ 19.580000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.876000] NET: Registered protocol family 24
[ 20.076000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 20.184000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 20.188000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 20.224000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 20.240000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 20.248000] hub 1-0:1.0: USB hub found
[ 20.252000] hub 1-0:1.0: 2 ports detected
[ 20.436000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 20.820000] usb 1-2: new high-speed USB device number 2 using bcm63xx_ehci
[ 20.964000] hub 1-2:1.0: USB hub found
[ 20.972000] hub 1-2:1.0: 4 ports detected
[ 21.276000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 21.712000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 21.820000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 21.824000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 21.836000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 21.900000] hub 2-0:1.0: USB hub found
[ 21.904000] hub 2-0:1.0: 1 port detected
[ 22.080000] Initializing USB Mass Storage driver...
[ 22.084000] usbcore: registered new interface driver usb-storage
[ 22.092000] USB Mass Storage support registered.
[ 22.128000] usbcore: registered new interface driver ums-alauda
[ 22.164000] usbcore: registered new interface driver ums-cypress
[ 22.200000] usbcore: registered new interface driver ums-datafab
[ 22.240000] usbcore: registered new interface driver ums-freecom
[ 22.276000] usbcore: registered new interface driver ums-isd200
[ 22.312000] usbcore: registered new interface driver ums-jumpshot
[ 22.352000] usbcore: registered new interface driver ums-karma
[ 22.392000] usbcore: registered new interface driver ums-sddr09
[ 22.428000] usbcore: registered new interface driver ums-sddr55
[ 22.468000] usbcore: registered new interface driver ums-usbat
[ 22.504000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 29.636000] eth0: link forced UP - 100/full - flow control off/off
[ 29.656000] device eth0 entered promiscuous mode
[ 29.668000] br-lan: port 1(eth0) entered forwarding state
[ 29.672000] br-lan: port 1(eth0) entered forwarding state
[ 31.676000] br-lan: port 1(eth0) entered forwarding state
[ 145.724000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 147.940000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 150.152000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 156.348000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 164.952000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 183.244000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 188.420000] wlan0: authenticate with 5c:4c:a9:72:a0:c1
[ 188.464000] wlan0: send auth to 5c:4c:a9:72:a0:c1 (try 1/3)
[ 188.472000] wlan0: authenticated
[ 188.512000] wlan0: associate with 5c:4c:a9:72:a0:c1 (try 1/3)
[ 188.524000] wlan0: RX AssocResp from 5c:4c:a9:72:a0:c1 (capab=0x411 status=0 aid=2)
[ 188.532000] wlan0: associated
[ 188.992000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[/spoiler]

[spoiler=DMESG 2º Boot]
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.208000] eth0: link forced UP - 100/full - flow control off/off
[ 3.428000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.492000] There is already a switch registered on the device 'eth0'
[ 5.960000] Button Hotplug driver version 0.4.1
[ 9.960000] JFFS2 notice: (337) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[ 12.936000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.944000] Backport based on wireless-testing.git master-2012-07-16
[ 12.948000] compat.git: wireless-testing.git
[ 13.020000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.024000] cfg80211: World regulatory domain updated:
[ 13.032000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.040000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.048000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.056000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.064000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.072000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.512000] NET: Registered protocol family 10
[ 13.964000] SCSI subsystem initialized
[ 14.056000] There is already a switch registered on the device 'eth0'
[ 14.416000] usbcore: registered new interface driver usbfs
[ 14.420000] usbcore: registered new interface driver hub
[ 14.428000] usbcore: registered new device driver usb
[ 15.580000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.588000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.768000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.772000] Registered led device: rt2800pci-phy0::radio
[ 15.772000] Registered led device: rt2800pci-phy0::assoc
[ 15.772000] Registered led device: rt2800pci-phy0::quality
[ 16.120000] PPP generic driver version 2.4.2
[ 16.512000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.804000] NET: Registered protocol family 24
[ 17.000000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.112000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.116000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.152000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.168000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.176000] hub 1-0:1.0: USB hub found
[ 17.180000] hub 1-0:1.0: 2 ports detected
[ 17.360000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 17.744000] usb 1-2: new high-speed USB device number 2 using bcm63xx_ehci
[ 17.888000] hub 1-2:1.0: USB hub found
[ 17.896000] hub 1-2:1.0: 4 ports detected
[ 18.188000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.604000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.712000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.716000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.724000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.792000] hub 2-0:1.0: USB hub found
[ 18.796000] hub 2-0:1.0: 1 port detected
[ 18.968000] Initializing USB Mass Storage driver...
[ 18.976000] usbcore: registered new interface driver usb-storage
[ 18.980000] USB Mass Storage support registered.
[ 19.020000] usbcore: registered new interface driver ums-alauda
[ 19.056000] usbcore: registered new interface driver ums-cypress
[ 19.092000] usbcore: registered new interface driver ums-datafab
[ 19.132000] usbcore: registered new interface driver ums-freecom
[ 19.168000] usbcore: registered new interface driver ums-isd200
[ 19.204000] usbcore: registered new interface driver ums-jumpshot
[ 19.244000] usbcore: registered new interface driver ums-karma
[ 19.280000] usbcore: registered new interface driver ums-sddr09
[ 19.320000] usbcore: registered new interface driver ums-sddr55
[ 19.356000] usbcore: registered new interface driver ums-usbat
[ 19.396000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 25.404000] eth0: link forced UP - 100/full - flow control off/off
[ 25.428000] device eth0 entered promiscuous mode
[ 25.440000] br-lan: port 1(eth0) entered forwarding state
[ 25.444000] br-lan: port 1(eth0) entered forwarding state
[ 27.448000] br-lan: port 1(eth0) entered forwarding state
[/spoiler]

[spoiler=DMESG 3º Boot]
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.200000] type=2000 audit(0.200:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.304000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.160000] eth0: link forced UP - 100/full - flow control off/off
[ 3.380000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.444000] There is already a switch registered on the device 'eth0'
[ 5.912000] Button Hotplug driver version 0.4.1
[ 9.920000] JFFS2 notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[ 12.900000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.908000] Backport based on wireless-testing.git master-2012-07-16
[ 12.912000] compat.git: wireless-testing.git
[ 12.980000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.984000] cfg80211: World regulatory domain updated:
[ 12.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.008000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.016000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.024000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.032000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.472000] NET: Registered protocol family 10
[ 13.928000] SCSI subsystem initialized
[ 14.020000] There is already a switch registered on the device 'eth0'
[ 14.380000] usbcore: registered new interface driver usbfs
[ 14.384000] usbcore: registered new interface driver hub
[ 14.392000] usbcore: registered new device driver usb
[ 15.544000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.552000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.732000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.736000] Registered led device: rt2800pci-phy0::radio
[ 15.736000] Registered led device: rt2800pci-phy0::assoc
[ 15.736000] Registered led device: rt2800pci-phy0::quality
[ 16.084000] PPP generic driver version 2.4.2
[ 16.476000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.768000] NET: Registered protocol family 24
[ 16.968000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.080000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.084000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.120000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.136000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.144000] hub 1-0:1.0: USB hub found
[ 17.148000] hub 1-0:1.0: 2 ports detected
[ 17.328000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 17.708000] usb 1-2: new high-speed USB device number 2 using bcm63xx_ehci
[ 17.856000] hub 1-2:1.0: USB hub found
[ 17.864000] hub 1-2:1.0: 4 ports detected
[ 18.156000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.572000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.684000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.688000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.696000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.764000] hub 2-0:1.0: USB hub found
[ 18.768000] hub 2-0:1.0: 1 port detected
[ 18.944000] Initializing USB Mass Storage driver...
[ 18.948000] usbcore: registered new interface driver usb-storage
[ 18.956000] USB Mass Storage support registered.
[ 18.992000] usbcore: registered new interface driver ums-alauda
[ 19.028000] usbcore: registered new interface driver ums-cypress
[ 19.068000] usbcore: registered new interface driver ums-datafab
[ 19.104000] usbcore: registered new interface driver ums-freecom
[ 19.140000] usbcore: registered new interface driver ums-isd200
[ 19.180000] usbcore: registered new interface driver ums-jumpshot
[ 19.216000] usbcore: registered new interface driver ums-karma
[ 19.256000] usbcore: registered new interface driver ums-sddr09
[ 19.292000] usbcore: registered new interface driver ums-sddr55
[ 19.328000] usbcore: registered new interface driver ums-usbat
[ 19.368000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 24.936000] eth0: link forced UP - 100/full - flow control off/off
[ 24.948000] device eth0 entered promiscuous mode
[ 24.956000] br-lan: port 1(eth0) entered forwarding state
[ 24.960000] br-lan: port 1(eth0) entered forwarding state
[ 26.964000] br-lan: port 1(eth0) entered forwarding state
[ 223.628000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 225.844000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 228.056000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 238.736000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 240.952000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 243.168000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 247.816000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 250.032000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 252.252000] ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.204000] type=2000 audit(0.204:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.308000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.500000] Freeing unused kernel memory: 200k freed
[ 3.164000] eth0: link forced UP - 100/full - flow control off/off
[ 3.384000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.448000] There is already a switch registered on the device 'eth0'
[ 5.916000] Button Hotplug driver version 0.4.1
[ 9.924000] JFFS2 notice: (337) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
[ 12.896000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 12.904000] Backport based on wireless-testing.git master-2012-07-16
[ 12.912000] compat.git: wireless-testing.git
[ 12.980000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.984000] cfg80211: World regulatory domain updated:
[ 12.992000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.008000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.016000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.024000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.032000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.472000] NET: Registered protocol family 10
[ 13.928000] SCSI subsystem initialized
[ 14.020000] There is already a switch registered on the device 'eth0'
[ 14.376000] usbcore: registered new interface driver usbfs
[ 14.384000] usbcore: registered new interface driver hub
[ 14.392000] usbcore: registered new device driver usb
[ 15.540000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.544000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.728000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.732000] Registered led device: rt2800pci-phy0::radio
[ 15.732000] Registered led device: rt2800pci-phy0::assoc
[ 15.732000] Registered led device: rt2800pci-phy0::quality
[ 16.080000] PPP generic driver version 2.4.2
[ 16.472000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.764000] NET: Registered protocol family 24
[ 16.964000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.072000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.076000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.112000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.128000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.136000] hub 1-0:1.0: USB hub found
[ 17.140000] hub 1-0:1.0: 2 ports detected
[ 17.320000] nf_conntrack version 0.5.0 (970 buckets, 3880 max)
[ 17.700000] usb 1-2: new high-speed USB device number 2 using bcm63xx_ehci
[ 17.848000] hub 1-2:1.0: USB hub found
[ 17.856000] hub 1-2:1.0: 4 ports detected
[ 18.148000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.564000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.672000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 18.676000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 18.684000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 18.752000] hub 2-0:1.0: USB hub found
[ 18.756000] hub 2-0:1.0: 1 port detected
[ 18.932000] Initializing USB Mass Storage driver...
[ 18.936000] usbcore: registered new interface driver usb-storage
[ 18.944000] USB Mass Storage support registered.
[ 18.980000] usbcore: registered new interface driver ums-alauda
[ 19.016000] usbcore: registered new interface driver ums-cypress
[ 19.056000] usbcore: registered new interface driver ums-datafab
[ 19.092000] usbcore: registered new interface driver ums-freecom
[ 19.128000] usbcore: registered new interface driver ums-isd200
[ 19.168000] usbcore: registered new interface driver ums-jumpshot
[ 19.204000] usbcore: registered new interface driver ums-karma
[ 19.244000] usbcore: registered new interface driver ums-sddr09
[ 19.280000] usbcore: registered new interface driver ums-sddr55
[ 19.320000] usbcore: registered new interface driver ums-usbat
[ 19.360000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 25.236000] eth0: link forced UP - 100/full - flow control off/off
[ 25.248000] device eth0 entered promiscuous mode
[ 25.256000] br-lan: port 1(eth0) entered forwarding state
[ 25.260000] br-lan: port 1(eth0) entered forwarding state
[ 27.264000] br-lan: port 1(eth0) entered forwarding state
[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Jul 21 02:06:44 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: Unable to find ath9k caldata.
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8029f750, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61892k/65536k available (2225k kernel code, 3644k reserved, 398k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 0 class 0x000280
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] PCI: CLS 0 bytes, default 16
[ 0.196000] audit: initializing netlink socket (disabled)
[ 0.204000] type=2000 audit(0.204:1): initialized
[ 0.208000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.216000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.224000] msgmni has been set to 120
[ 0.228000] io scheduler noop registered
[ 0.232000] io scheduler deadline registered (default)
[ 0.240000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.248000] console [ttyS0] enabled, bootconsole disabled
[ 0.268000] physmap platform flash device: 02000000 at 1e000000
[ 0.272000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.284000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.284000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.288000] Amd/Fujitsu Extended Query version 1.3.
[ 0.296000] number of CFI chips: 1
[ 0.300000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.308000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.312000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.320000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.328000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.336000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.344000] bcm63xxpart: Spare partition is offset 340004 and length abfffc
[ 0.348000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.356000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000120000 : "kernel"
[ 0.376000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=AC0000
[ 0.416000] 0x000000340000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.436000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.456000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] Registered led device: HW556:red:message
[ 0.464000] Registered led device: HW556:red:hspa
[ 0.464000] Registered led device: HW556:red:dsl
[ 0.468000] Registered led device: HW556:red:power
[ 0.468000] Registered led device: HW556:red:all
[ 0.468000] TCP cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.476000] 8021q: 8
[/spoiler]

Goofre · « **Respuesta #539 en:** 25-07-2012, 21:07 (Miércoles) »

Hola a todos:

¿Sabeis de algun ultimo firmware para el router hg556a que tenga Relayd?, antes usaba el

fpu.LuCi.samba.etc.r30964.openwrt-HW556-squashfs-cfe.bin

pero algun virus me lo dejó inservible, ya puesto buscaria el mas actual posible.

Os agradeceria que me dijerais donde puedo encontrarlo. Muchas Gracias.

Noticias:

Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a (Leído 2125599 veces)

emeryth

Noltari

emeryth

Noltari

emeryth

tool

Noltari

tool

Noltari

Noltari

Noltari

tool

Noltari

tool

Noltari

tool

Goofre