Teneis algún link a alguna compilación trunk para el 7518 que tenga la compatibilidad con el wifi?. He bajado el paquete de dani17 en que parece reconocer el wifi pero no soy capaz de hacer funcionar la tarjeta de red. En la pagina de openwrt no se porqué en la rama trunk no hay ninguna compilación.
Edito para no monopolizar esta página :-)
He bajado la compilación Attitude adjustement ya que no encuentro la compilación de la rama trunk. Me he bajado el archivo
http://downloads.openwrt.org/attitude_adjustment/12.09-beta/lantiq/danube/openwrt-lantiq-danube-ARV7518PW-squashfs.imageLa he cargado al router pero parece que tiene algun problema. Alguien sabria decirme si esto es un bug o es algo que se pueda arreglar?
[spoiler] Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2012-09-04 19:43:24 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1012019 Bytes = 988.3 kB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc ve rsion 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Fri Aug 31 16:20 :51 UTC 2012
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,j ffs2 machtype=ARV7518PW
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 byt es
[ 0.000000] Writing ErrCtl register=0006f828
[ 0.000000] Readback ErrCtl register=0006f828
[ 0.000000] Memory: 61832k/65536k available (2399k kernel code, 3704k reserve d, 403k data, 176k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.060000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio
[ 0.064000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio
[ 0.068000] MIPS: machine is ARV7518PW - ASTORIA
[ 0.072000] gpiochip_add: registered GPIOs 100 to 115 on device: ltq_ebu
[ 0.112000] bio: create slab <bio-0> at 0
[ 0.120000] PCI host bridge to bus 0000:00
[ 0.124000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.128000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.132000] pci 0000:00:0e.0: fixup device configuration
[ 0.136000] pci 0000:00:0e.0: fixup info: [168c:0029] revision 01 class 0x028 000
[ 0.140000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.144000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
[ 0.148000] Switching to clocksource MIPS
[ 0.156000] NET: Registered protocol family 2
[ 0.164000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.168000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.176000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.184000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.188000] TCP reno registered
[ 0.192000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.200000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.204000] NET: Registered protocol family 1
[ 0.212000] gptu: totally 6 16-bit timers/counters
[ 0.216000] gptu: misc_register on minor 63
[ 0.220000] gptu: succeeded to request irq 126
[ 0.224000] gptu: succeeded to request irq 127
[ 0.228000] gptu: succeeded to request irq 128
[ 0.232000] gptu: succeeded to request irq 129
[ 0.240000] gptu: succeeded to request irq 130
[ 0.244000] gptu: succeeded to request irq 131
[ 0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.256000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY ) (c) 2001-2006 Red Hat, Inc.
[ 0.268000] msgmni has been set to 120
[ 0.272000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54)
[ 0.280000] io scheduler noop registered
[ 0.284000] io scheduler deadline registered (default)
[ 0.288000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[ 0.296000] console [ttyLTQ1] enabled, bootconsole disabled
[ 0.296000] console [ttyLTQ1] enabled, bootconsole disabled
[ 0.312000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.320000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.324000] Amd/Fujitsu Extended Query version 1.1.
[ 0.328000] number of CFI chips: 1
[ 0.332000] Creating 4 MTD partitions on "ltq_nor":
[ 0.336000] 0x000000000000-0x000000010000 : "uboot"
[ 0.344000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.352000] 0x000000020000-0x0000007f0000 : "linux"
[ 0.360000] found squashfs behind kernel
[ 0.360000] Creating 2 MTD partitions on "ltq_nor":
[ 0.364000] 0x000000020000-0x000000117173 : "kernel"
[ 0.372000] mtd: partition "kernel" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.384000] 0x000000117173-0x0000007f0000 : "rootfs"
[ 0.388000] mtd: partition "rootfs" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.408000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, l en=510000
[ 0.416000] 0x0000002e0000-0x0000007f0000 : "rootfs_data"
[ 0.424000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.580000] ltq_mii: probed
[ 0.604000] eth0: Atheros AR8216 switch driver attached.
[ 0.704000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=ltq_e top-fffffff:00, irq=-1)
[ 0.724000] TCP cubic registered
[ 0.728000] NET: Registered protocol family 17
[ 0.732000] 8021q: 802.1Q VLAN Support[ 0.748000] VFS: Mounted root (squas hfs filesystem) readonly on device 31:4.
[ 0.756000] Freeing unused kernel memory: 176k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 7.032000] JFFS2 notice: (412) jffs2_build_xattr_subsystem: complete buildin g xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -
[ 7.520000] JFFS2 compression type 0x06 not available.
[ 7.524000] Error: jffs2_decompress returned -5
[ 7.528000] JFFS2 compression type 0x06 not available.
[ 7.532000] Error: jffs2_decompress returned -5
[ 7.536000] JFFS2 compression type 0x06 not available.
[ 7.544000] Error: jffs2_decompress returned -5
[ 7.548000] JFFS2 compression type 0x06 not available.
[ 7.552000] Error: jffs2_decompress returned -5
[ 7.556000] JFFS2 compression type 0x06 not available.
[ 7.560000] Error: jffs2_decompress returned -5
[ 7.568000] JFFS2 compression type 0x06 not available.
[ 7.572000] Error: jffs2_decompress returned -5
[ 7.576000] JFFS2 compression type 0x06 not available.
[ 7.580000] Error: jffs2_decompress returned -5
[ 7.588000] JFFS2 compression type 0x06 not available.
[ 7.592000] Error: jffs2_decompress returned -5
[ 7.596000] JFFS2 compression type 0x06 not available.
[ 7.600000] Error: jffs2_decompress returned -5
[ 7.604000] JFFS2 compression type 0x06 not available.
[ 7.608000] Error: jffs2_decompress returned -5
[ 7.616000] JFFS2 compression type 0x06 not available.
[ 7.620000] Error: jffs2_decompress returned -5
[ 7.624000] JFFS2 compression type 0x06 not available.
[ 7.628000] Error: jffs2_decompress returned -5
[ 7.632000] JFFS2 compression type 0x06 not available.
[ 7.636000] Error: jffs2_decompress returned -5
[ 7.644000] JFFS2 compression type 0x06 not available.
[ 7.648000] Error: jffs2_decompress returned -5
[ 7.652000] JFFS2 compression type 0x06 not available.
[ 7.656000] Error: jffs2_decompress returned -5
[ 7.660000] JFFS2 compression type 0x06 not available.
[ 7.664000] Error: jffs2_decompress returned -5
[ 7.672000] JFFS2 compression type 0x06 not available.
[ 7.676000] Error: jffs2_decompress returned -5
[ 7.680000] JFFS2 compression type 0x06 not available.
[ 7.684000] Error: jffs2_decompress returned -5
[ 7.692000] JFFS2 compression type 0x06 not available.
[ 7.696000] Error: jffs2_decompress returned -5
[ 7.700000] JFFS2 compression type 0x06 not available.
[ 7.704000] Error: jffs2_decompress returned -5
[ 7.708000] JFFS2 compression type 0x06 not available.
[ 7.712000] Error: jffs2_decompress returned -5
[ 7.716000] JFFS2 compression type 0x06 not available.
[ 7.724000] Error: jffs2_decompress returned -5
[ 7.728000] JFFS2 compression type 0x06 not available.
[ 7.732000] Error: jffs2_decompress returned -5
[ 7.736000] JFFS2 compression type 0x06 not available.
[ 7.740000] Error: jffs2_decompress returned -5
[ 7.744000] JFFS2 compression type 0x06 not available.
[ 7.752000] Error: jffs2_decompress returned -5
[ 7.756000] JFFS2 compression type 0x06 not available.
[ 7.760000] Error: jffs2_decompress returned -5
[ 7.764000] JFFS2 compression type 0x06 not available.
[ 7.768000] Error: jffs2_decompress returned -5
[ 7.772000] JFFS2 compression type 0x06 not available.
[ 7.780000] Error: jffs2_decompress returned -5
[ 7.784000] JFFS2 compression type 0x06 not available.
[ 7.788000] Error: jffs2_decompress returned -5
[ 7.792000] JFFS2 compression type 0x06 not available.
[ 7.800000] Error: jffs2_decompress returned -5
[ 7.804000] JFFS2 compression type 0x06 not available.
[ 7.808000] Error: jffs2_decompress returned -5
[ 7.812000] JFFS2 compression type 0x06 not available.
[ 7.816000] Error: jffs2_decompress returned -5
[ 7.820000] JFFS2 compression type 0x06 not available.
[ 7.828000] Error: jffs2_decompress returned -5
[ 7.832000] JFFS2 compression type 0x06 not available.
[ 7.836000] Error: jffs2_decompress returned -5
[ 7.840000] JFFS2 compression type 0x06 not available.
[ 7.844000] Error: jffs2_decompress returned -5
[ 7.848000] JFFS2 compression type 0x06 not available.
[ 7.856000] Error: jffs2_decompress returned -5
[ 7.860000] JFFS2 compression type 0x06 not available.
[ 7.864000] Error: jffs2_decompress returned -5
[ 7.868000] JFFS2 compression type 0x06 not available.
[ 7.872000] Error: jffs2_decompress returned -5
[ 7.880000] JFFS2 compression type 0x06 not available.
[ 7.884000] Error: jffs2_decompress returned -5
[ 7.888000] JFFS2 compression type 0x06 not available.
[ 7.892000] Error: jffs2_decompress returned -5
[ 7.900000] JFFS2 compression type 0x06 not available.
[ 7.900000] Error: jffs2_decompress returned -5
[ 7.908000] JFFS2 compression type 0x06 not available.
[ 7.912000] Error: jffs2_decompress returned -5
[ 7.916000] JFFS2 compression type 0x06 not available.
[ 7.920000] Error: jffs2_decompress returned -5
[ 7.924000] JFFS2 compression type 0x06 not available.
[ 7.928000] Error: jffs2_decompress returned -5
[ 7.936000] JFFS2 compression type 0x06 not available.
[ 7.940000] Error: jffs2_decompress returned -5
[ 7.944000] JFFS2 compression type 0x06 not available.
[ 7.948000] Error: jffs2_decompress returned -5
[ 7.956000] JFFS2 compression type 0x06 not available.
[ 7.960000] Error: jffs2_decompress returned -5
[ 7.964000] JFFS2 compression type 0x06 not available.
[ 7.968000] Error: jffs2_decompress returned -5
[ 7.972000] JFFS2 compression type 0x06 not available.
[ 7.976000] Err
Y ahí se queda en un bucle. No para de repetir lo mismo.
[/spoiler]