Autor Tema: [Desarrollo] OpenWRT para routers Astoria de ya.com (ARV4518/ARV7518) (Leído 699211 veces)

Pteridium · « **Respuesta #400 en:** 25-01-2013, 20:13 (Viernes) »

Sí, ajusté un poco de más.

Es la pega de usar esas flags, que el código está mucho más optimizado pero es más gordo y tira algo más de la RAM. También te puedes encontrar alguna aplicación que vaya mal o algo más lenta.
Es sólo un parche pero menos es nada.

Lesgar · « **Respuesta #401 en:** 25-01-2013, 23:48 (Viernes) »

El usb funciona y el mdoem adsl parece que tambien, los problemas que le veo a estas imagenes es que se ejecutan en la ram, no se pueden guardar los cambios. Aqui pego los bootlogs he probado las dos y con las dos direcciones del kernel. Estoy haciendo algo mal? se admiten ideas, gracias

ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 2 1 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-25 11:20:58 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1184504 Bytes = 1.1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.2 (pepe@debian) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Fri Jan 25 12:20:39 CET 2013

[ 0.000000] SoC: Danube rev 1.3

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)

[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 04000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] __ex_table already sorted, skipping sort

[ 0.000000] Writing ErrCtl register=00068a78

[ 0.000000] Readback ErrCtl register=00068a78

[ 0.000000] Memory: 61208k/65536k available (2532k kernel code, 4328k reserved, 770k data, 208k init, 0k highmem)

[ 0.000000] NR_IRQS:256

[ 0.000000] CPU Clock: 333MHz

[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[ 0.036000] pid_max: default: 32768 minimum: 301

[ 0.040000] Mount-cache hash table entries: 512

[ 0.048000] pinctrl core: initialized pinctrl subsystem

[ 0.052000] NET: Registered protocol family 16

[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done

[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20

[ 0.104000] bio: create slab <bio-0> at 0

[ 0.112000] usbcore: registered new interface driver usbfs

[ 0.116000] usbcore: registered new interface driver hub

[ 0.120000] usbcore: registered new device driver usb

[ 0.124000] Switching to clocksource MIPS

[ 0.132000] NET: Registered protocol family 2

[ 0.140000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[ 0.144000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.152000] TCP: Hash tables configured (established 2048 bind 2048)

[ 0.160000] TCP: reno registered

[ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.168000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.176000] NET: Registered protocol family 1

[ 0.180000] gptu: totally 6 16-bit timers/counters

[ 0.184000] gptu: misc_register on minor 63

[ 0.188000] gptu: succeeded to request irq 126

[ 0.192000] gptu: succeeded to request irq 127

[ 0.196000] gptu: succeeded to request irq 128

[ 0.204000] gptu: succeeded to request irq 129

[ 0.208000] gptu: succeeded to request irq 130

[ 0.212000] gptu: succeeded to request irq 131

[ 0.224000] lantiq,vmmc 1f103000.vmmc: requested GPIO 255

[ 0.228000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03900000

[ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.244000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[ 0.256000] msgmni has been set to 119

[ 0.260000] io scheduler noop registered

[ 0.264000] io scheduler deadline registered (default)

[ 0.268000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled

[ 0.292000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022f9
[ 0.300000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.304000] Amd/Fujitsu Extended Query version 1.1.
[ 0.312000] number of CFI chips: 1
[ 0.312000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.320000] Creating 4 MTD partitions on "ltq_nor":
[ 0.324000] 0x000000000000-0x000000010000 : "uboot"
[ 0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.340000] 0x000000020000-0x0000003f0000 : "linux"
[ 0.344000] found squashfs behind kernel
[ 0.348000] Creating 2 MTD partitions on "ltq_nor":
[ 0.352000] 0x000000020000-0x000000141338 : "kernel"
[ 0.356000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.372000] 0x000000141338-0x0000003f0000 : "rootfs"
[ 0.376000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] mtd: partition "rootfs" set to be root filesystem
[ 0.396000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=60000
[ 0.404000] 0x000000390000-0x0000003f0000 : "rootfs_data"
[ 0.412000] 0x0000003f0000-0x000000400000 : "boardconfig"
[ 0.424000] etop: invalid MAC, using random
[ 0.440000] libphy: ltq_mii: probed
[ 0.472000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
[ 0.480000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.492000] wdt 1f8803f0.watchdog: Init done
[ 0.496000] leds-gpio gpio-leds.5: pins are not configured from the driver
[ 0.508000] TCP: cubic registered
[ 0.512000] NET: Registered protocol family 17
[ 0.516000] 8021q: 802.1Q VLAN Support v1.8
[ 0.532000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.540000] Freeing unused kernel memory: 208k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console.

[ 10.568000] SCSI subsystem initialized
[ 10.896000] NET: Registered protocol family 8
[ 10.900000] NET: Registered protocol family 20
[ 11.952000] PPP generic driver version 2.4.2
[ 12.296000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.712000] NET: Registered protocol family 24
[ 12.888000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 13.732000] IFX MEI Version 5.00.00
[ 13.760000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 14.268000] IFXUSB: USB core #0 soft-reset
[ 14.472000] IFXUSB: USB core #0 soft-reset
[ 14.472000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 14.476000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 14.484000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 14.492000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[ 14.496000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[ 14.504000] IFXUSB: Init: Power Port (0)
[ 14.508000] hub 1-0:1.0: USB hub found
[ 14.508000] hub 1-0:1.0: 1 port detected
[ 14.516000] ifxusb_hcd ifxusb_hcd: requested GPIO 238
[ 14.692000] ATM1.0.26 ATM (A1) firmware version 0.17
[ 14.812000] Initializing USB Mass Storage driver...
[ 14.816000] usbcore: registered new interface driver usb-storage
[ 14.820000] USB Mass Storage support registered.
[ 15.100000] usb 1-1: new high-speed USB device number 2 using ifxusb_hcd
[ 15.300000] scsi0 : usb-storage 1-1:1.0
[ 16.516000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler G3 1.00 PQ: 0 ANSI: 2
[ 16.528000] sd 0:0:0:0: [sda] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 16.544000] sd 0:0:0:0: [sda] Write Protect is off
[ 16.548000] sd 0:0:0:0: [sda] No Caching mode page present
[ 16.552000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 16.564000] sd 0:0:0:0: [sda] No Caching mode page present
[ 16.568000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 28.544000] device eth0 entered promiscuous mode
[ 28.556000] br-lan: port 1(eth0) entered forwarding state
[ 28.560000] br-lan: port 1(eth0) entered forwarding state
[ 30.564000] br-lan: port 1(eth0) entered forwarding state
[ 52.612000] jffs2: notice: (1355) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

ROM VER: 1.0.3
CFG 01
Readü
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 2
ARV4518 => setenv kernel_addr 0xb0030000
ARV4518 => saveenv
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... 9....8....7....6....5....4....3....2....1....done
Protected 1 sectors
ARV4518 => reset
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 2 1 0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Failed to execute bootcmd (maybe invalid u-boot environment?), starting httpd to update firmware...
starting httpd server from server 192.168.1.1
http start
.....request for file /
.........expecting 3670262 bytes
received data will be stored at 80500000
811 / 3670020

---Cortado por inutil----

3670069 / 3670020
Bytes transferred = 3670020 (380004 hex)
http upload ready

## Checking Image at 80500000 ...
Legacy image found
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-25 11:20:58 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1184504 Bytes = 1.1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
http ugrade ...

......................................................... done
Erased 57 sectors
Copy to Flash... 9....8....7....6....5....4....3....2....1....0done
http ugrade ready

ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 2 1 0
## Booting kernel from Legacy Image at b0030000 ...
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-25 11:20:58 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1184504 Bytes = 1.1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.2 (pepe@debian) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Fri Jan 25 12:20:39 CET 2013

[ 0.000000] SoC: Danube rev 1.3

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)

[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 04000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] __ex_table already sorted, skipping sort

[ 0.000000] Writing ErrCtl register=00068a70

[ 0.000000] Readback ErrCtl register=00068a70

[ 0.000000] Memory: 61208k/65536k available (2532k kernel code, 4328k reserved, 770k data, 208k init, 0k highmem)

[ 0.000000] NR_IRQS:256

[ 0.000000] CPU Clock: 333MHz

[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[ 0.036000] pid_max: default: 32768 minimum: 301

[ 0.040000] Mount-cache hash table entries: 512

[ 0.048000] pinctrl core: initialized pinctrl subsystem

[ 0.052000] NET: Registered protocol family 16

[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done

[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20

[ 0.104000] bio: create slab <bio-0> at 0

[ 0.112000] usbcore: registered new interface driver usbfs

[ 0.116000] usbcore: registered new interface driver hub

[ 0.120000] usbcore: registered new device driver usb

[ 0.124000] Switching to clocksource MIPS

[ 0.132000] NET: Registered protocol family 2

[ 0.140000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[ 0.144000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.152000] TCP: Hash tables configured (established 2048 bind 2048)

[ 0.160000] TCP: reno registered

[ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.168000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.176000] NET: Registered protocol family 1

[ 0.180000] gptu: totally 6 16-bit timers/counters

[ 0.184000] gptu: misc_register on minor 63

[ 0.188000] gptu: succeeded to request irq 126

[ 0.192000] gptu: succeeded to request irq 127

[ 0.196000] gptu: succeeded to request irq 128

[ 0.204000] gptu: succeeded to request irq 129

[ 0.208000] gptu: succeeded to request irq 130

[ 0.212000] gptu: succeeded to request irq 131

[ 0.224000] lantiq,vmmc 1f103000.vmmc: requested GPIO 255

[ 0.228000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03900000

[ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.244000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[ 0.256000] msgmni has been set to 119

[ 0.260000] io scheduler noop registered

[ 0.264000] io scheduler deadline registered (default)

[ 0.268000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc

[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled

[ 0.292000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022f9
[ 0.300000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.304000] Amd/Fujitsu Extended Query version 1.1.
[ 0.312000] number of CFI chips: 1
[ 0.312000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.320000] Creating 4 MTD partitions on "ltq_nor":
[ 0.324000] 0x000000000000-0x000000010000 : "uboot"
[ 0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.340000] 0x000000020000-0x0000003f0000 : "linux"
[ 0.344000] Creating 2 MTD partitions on "ltq_nor":
[ 0.348000] 0x000000020000-0x000000150000 : "kernel"
[ 0.356000] 0x000000150000-0x0000003f0000 : "rootfs"
[ 0.364000] mtd: partition "rootfs" set to be root filesystem
[ 0.368000] split_squashfs: no squashfs found in "ltq_nor"
[ 0.372000] 0x0000003f0000-0x000000400000 : "boardconfig"
[ 0.388000] etop: invalid MAC, using random
[ 0.404000] libphy: ltq_mii: probed
[ 0.436000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
[ 0.440000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.452000] wdt 1f8803f0.watchdog: Init done
[ 0.456000] leds-gpio gpio-leds.5: pins are not configured from the driver
[ 0.472000] TCP: cubic registered
[ 0.472000] NET: Registered protocol family 17
[ 0.480000] 8021q: 802.1Q VLAN Support v1.8
[ 0.488000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,4)

Noltari · « **Respuesta #402 en:** 26-01-2013, 17:57 (Sábado) »

Lesgar, prueba este firmware cuando puedas:
https://dl.dropbox.com/u/4708147/openwrt/arv4518/openwrt-lantiq-xway-ARV4518PW-squashfs.image

Seguro que tira excepciones, pero he metido cierto debug.

Saludos.

Lesgar · « **Respuesta #403 en:** 26-01-2013, 18:24 (Sábado) »

Te adjunto el bootlog de la imagen anterior y te pongo ademas otro (mucho mas antiguo) en el que si se carga el bus pci (probado en mi router)
-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 2 1 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.4
Created: 2013-01-26 16:53:50 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1206925 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.4 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Sat Jan 26 17:53:40 CET 2013

[ 0.000000] SoC: Danube rev 1.3

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)

[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 04000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Zone ranges:

[ 0.000000] Normal [mem 0x00000000-0x03ffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]

[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.

[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] __ex_table already sorted, skipping sort

[ 0.000000] Writing ErrCtl register=00068a70

[ 0.000000] Readback ErrCtl register=00068a70

[ 0.000000] Memory: 61124k/65536k available (2580k kernel code, 4412k reserved, 785k data, 208k init, 0k highmem)

[ 0.000000] NR_IRQS:256

[ 0.000000] CPU Clock: 333MHz

[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)

[ 0.040000] pid_max: default: 32768 minimum: 301

[ 0.044000] Mount-cache hash table entries: 512

[ 0.048000] pinctrl core: initialized pinctrl subsystem

[ 0.052000] NET: Registered protocol family 16

[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done

[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20

[ 0.084000] Debug #1

[ 0.088000] Debug #2

[ 0.088000] Debug #3

[ 0.092000] Debug #4

[ 0.092000] Debug #5

[ 0.096000] Data bus error, epc == 802810e0, ra == 802810c8

[ 0.096000] Oops[#1]:

[ 0.096000] Cpu 0

[ 0.096000] $ 0 : 00000000 00000000 be105400 feffffff

[ 0.096000] $ 4 : ffffffff 803a8fb0 00000001 000041c6

[ 0.096000] $ 8 : 83854620 00000002 00000001 0000002d

[ 0.096000] $12 : 00000000 00000000 00000000 0000002d

[ 0.096000] $16 : 803b0000 83854580 81002078 83854590

[ 0.096000] $20 : 803b0000 803b0000 803b0000 803b0000

[ 0.096000] $24 : 00000003 8014e9f0

[ 0.096000] $28 : 8381c000 8381dd60 8032b730 802810c8

[ 0.096000] Hi : 000023f0

[ 0.096000] Lo : 00008fc0

[ 0.096000] epc : 802810e0 ltq_pci_probe+0x284/0x4fc

[ 0.096000] Not tainted

[ 0.096000] ra : 802810c8 ltq_pci_probe+0x26c/0x4fc

[ 0.096000] Status: 1100fc03 KERNEL EXL IE

[ 0.096000] Cause : 1080001c

[ 0.096000] PrId : 00019641 (MIPS 24KEc)

[ 0.096000] Modules linked in:

[ 0.096000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)

[ 0.096000] Stack : 83854598 8385b790 00000001 00000001 0000001d 83854590 803b0000 80347894

ffffffed 8032f280 80347894 0000001d 8034c210 8017a930 83854590 80347894

80347894 8017c340 834015e0 838545c4 83854590 80347894 80347894 00000000

80380000 8017ab08 80347894 80178c1c 83853180 00000000 00000000 80347894

8017aa9c 80178f18 00000000 80275ee8 80340ae0 80178b9c 838184cc 83853430

...

[ 0.096000] Call Trace:

[ 0.096000] [<802810e0>] ltq_pci_probe+0x284/0x4fc

[ 0.096000] [<8017a930>] driver_probe_device+0x138/0x2a4

[ 0.096000] [<8017ab08>] __driver_attach+0x6c/0xa4

[ 0.096000] [<80178f18>] bus_for_each_dev+0x54/0x98

[ 0.096000] [<80179ec0>] bus_add_driver+0xbc/0x244

[ 0.096000] [<8017aeb0>] driver_register+0xbc/0x178

[ 0.096000] [<8035efa4>] pcibios_init+0x18/0x40

[ 0.096000] [<80006500>] do_one_initcall+0xf0/0x1c0

[ 0.096000] [<8027822c>] kernel_init+0x138/0x2c0

[ 0.096000] [<8000b41c>] kernel_thread_helper+0x10/0x18

[ 0.096000]

[ 0.096000]

Code: 8c440030 3c03feff 3463ffff <00831824> ac430030 0000000f 8ee3e790 8e02e794 3c058031

[ 0.100000] ---[ end trace 139ce121c98e96c9 ]---

[ 0.104000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b

[ 0.104000]

------------------------------------------------------------------------------------------

PCI que si funciona

U-Boot 2010.03 (Oct 28 2010 - 21:50:55)

Board: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
*** Warning - bad CRC, using default environment

Net:
searching for rtl8306 switch ... found
lq_cpe_eth

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 5 4 3 2 1 0
## Booting kernel from Legacy Image at b007d000 ...
Image Name: MIPS OpenWrt Linux-2.6.33.7
Created: 2010-10-28 18:34:29 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2208638 Bytes = 2.1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.33.7 (norberto@orion) (gcc version 4.3.3 (GCC) ) #22 Thu Oct 28 20:34:09 CEST 2010

bootconsole [early0] enabled

CPU revision is: 00019641 (MIPS 24Kc)

Determined physical RAM map:

memory: 04000000 @ 00000000 (usable)

Initrd not found or empty - disabling initrd

Zone PFN ranges:

Normal 0x00000000 -> 0x00004000

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

0: 0x00000000 -> 0x00004000

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

Kernel command line: rootfstype=squashfs,jffs2 ip=192.168.2.1:192.168.2.101:192.168.2.254:255.255.255.0:::off init=/etc/preinit console=ttyS1,115200 ethaddr=00:13:f7:97:70:84 mtdparts=ifx-nor:128k(brnboot)ro,256k(brn_env)ro,58k(uboot)ro,58k(uboot_env)ro,64k(kernel),-(rootfs) console=ttyS0,9600 console=ttyS1,115200n8 rootfstype=squashfs,jffs2

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.

Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

Writing ErrCtl register=00068a70

Readback ErrCtl register=00068a70

Memory: 57724k/65536k available (2181k kernel code, 7736k reserved, 374k data, 4484k init, 0k highmem)

Hierarchical RCU implementation.

NR_IRQS:256

Linux version 2.6.33.7 (norberto@orion) (gcc version 4.3.3 (GCC) ) #22 Thu Oct 28 20:34:09 CEST 2010

bootconsole [early0] enabled

CPU revision is: 00019641 (MIPS 24Kc)

Determined physical RAM map:

memory: 04000000 @ 00000000 (usable)

Initrd not found or empty - disabling initrd

Zone PFN ranges:

Normal 0x00000000 -> 0x00004000

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

0: 0x00000000 -> 0x00004000

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

Kernel command line: rootfstype=squashfs,jffs2 ip=192.168.2.1:192.168.2.101:192.168.2.254:255.255.255.0:::off init=/etc/preinit console=ttyS1,115200 ethaddr=00:13:f7:97:70:84 mtdparts=ifx-nor:128k(brnboot)ro,256k(brn_env)ro,58k(uboot)ro,58k(uboot_env)ro,64k(kernel),-(rootfs) console=ttyS0,9600 console=ttyS1,115200n8 rootfstype=squashfs,jffs2

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.

Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

Writing ErrCtl register=00068a70

Readback ErrCtl register=00068a70

Memory: 57724k/65536k available (2181k kernel code, 7736k reserved, 374k data, 4484k init, 0k highmem)

Hierarchical RCU implementation.

NR_IRQS:256

console [ttyS0] enabled

console [ttyS1] enabled, bootconsole disabled
console [ttyS1] enabled, bootconsole disabled

Calibrating delay loop... 221.69 BogoMIPS (lpj=443392)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is Arcadyan ARV4518, SMC 7908A
regdomain: 0xffffffff --> 0x0
PCI: Probing PCI hardware on host bus 0.
IFXMips PCI mapped to 0xB7000000
IFXMips PCI I/O mapped to 0xBAE00000
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:0e.0: unsupported PM cap regs version (4)
pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
pci 0000:00:0e.0: BAR 0: set to [mem 0x18000000-0x1800ffff] (PCI address [0x18000000-0x1800ffff]
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 126
gptu: succeeded to request irq 127
gptu: succeeded to request irq 128
gptu: succeeded to request irq 129
gptu: succeeded to request irq 130
gptu: succeeded to request irq 131
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 112
io scheduler noop registered
io scheduler deadline registered (default)
ttyS0 at MMIO 0xbe100400 (irq = 104) is a asc0
ttyS1 at MMIO 0xbe100c00 (irq = 111) is a asc1
eth0: using mac=00:13:F7:97:70:84
ifxmips_mii: probed
Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
eth0: attached PHY driver [Realtek RTL8306S] (mii_bus:phy_addr=0:00, irq=-1)
ifxmips_mii0: driver loaded!
ifxmips_wdt: loaded
Registered led device: ifx:green:power
Registered led device: ifx:red:power
Registered led device: ifx:green:wlan
Registered led device: ifx:green:adsl
Registered led device: ifx:green:internet
Registered led device: ifx:red:internet
Registered led device: ifx:green:usb
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory:- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. IFXOS, Version 1.5.12 (c) Copyright 2009, Lantiq Deutschland GmbH

SCSI subsystem initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (973 buckets, 3892 max)
IFX MEI Version 5.00.00

Infineon CPE API Driver version: DSL CPE API V3.24.4.4
Infineon Technologies ATM driver version 1.0.8
Infineon Technologies ATM (A1) firmware version 0.1
ifxmips_atm: ATM init succeed
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
gpio-buttons driver version 0.1.2
input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
-----------------------------------------------------------------------

Noltari · « **Respuesta #404 en:** 26-01-2013, 18:38 (Sábado) »

Siento tener que pedirte otra prueba, pero estoy intentando identificar qué es lo que está haciendo que ocurra una excepción.

Cuando puedas prueba esta otra imagen: https://dl.dropbox.com/u/4708147/openwrt/arv4518/openwrt-lantiq-xway-ARV4518PW-squashfs_test2.image

Saludos.

Lesgar · « **Respuesta #405 en:** 26-01-2013, 18:56 (Sábado) »

aqui tienes:

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.4
Created: 2013-01-26 17:36:30 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1207281 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.4 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #2 Sat Jan 26 18:36:19 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61124k/65536k available (2581k kernel code, 4412k reserved, 784k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.048000] NET: Registered protocol family 16
[ 0.068000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.072000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.080000] Debug #1
[ 0.084000] Debug #1a
[ 0.084000] Debug #2
[ 0.088000] Debug #3
[ 0.088000] Debug #4
[ 0.092000] Debug #5
[ 0.092000] Debug #5.1
[ 0.096000] Debug #5.2
[ 0.096000] Debug #5.3
[ 0.100000] Debug #5.4
[ 0.100000] Debug #5.4 (if)
[ 0.104000] Debug #5.5
[ 0.104000] Debug #5.5 (if1)
[ 0.108000] Debug #5.5 (if2)
[ 0.108000] Debug #5.6
[ 0.112000] Debug #5.6 (if1)
[ 0.112000] Debug #5.6 (if2)
[ 0.116000] Debug #5.6 (if4)
[ 0.116000] Debug #5.7
[ 0.120000] Data bus error, epc == 80281218, ra == 80281200
[ 0.120000] Oops[#1]:
[ 0.120000] Cpu 0
[ 0.120000] $ 0 : 00000000 00000000 be105400 feffffff
[ 0.120000] $ 4 : 8030ddd8 ffffffff 0000003b 00000910
[ 0.120000] $ 8 : 00000037 00000003 803840e8 0000003b
[ 0.120000] $12 : 00000000 00000000 00000000 0000003b
[ 0.120000] $16 : 00000000 83854580 803b0000 83854590
[ 0.120000] $20 : 803b0000 81002078 803b0000 803b0000
[ 0.120000] $24 : 00000001 00000000
[ 0.120000] $28 : 8381c000 8381dd60 8032bb20 80281200
[ 0.120000] Hi : 00000488
[ 0.120000] Lo : 00001220
[ 0.120000] epc : 80281218 ltq_pci_probe+0x3bc/0x874
[ 0.120000] Not tainted
[ 0.120000] ra : 80281200 ltq_pci_probe+0x3a4/0x874
[ 0.120000] Status: 1100fc03 KERNEL EXL IE
[ 0.120000] Cause : 1080001c
[ 0.120000] PrId : 00019641 (MIPS 24KEc)
[ 0.120000] Modules linked in:
[ 0.120000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)
[ 0.120000] Stack : 83854598 0000003a 0000003a 00000910 0000001d 83854590 803b0000 80347894
ffffffed 8032f280 80347894 0000001d 8034c210 8017a930 83854590 80347894
80347894 8017c340 834015e0 838545c4 83854590 80347894 80347894 00000000
80380000 8017ab08 80347894 80178c1c 83853180 00000000 00000000 80347894
8017aa9c 80178f18 00000000 80275ee8 80340ae0 80178b9c 838184cc 83853430
...
[ 0.120000] Call Trace:
[ 0.120000] [<80281218>] ltq_pci_probe+0x3bc/0x874
[ 0.120000] [<8017a930>] driver_probe_device+0x138/0x2a4
[ 0.120000] [<8017ab08>] __driver_attach+0x6c/0xa4
[ 0.120000] [<80178f18>] bus_for_each_dev+0x54/0x98
[ 0.120000] [<80179ec0>] bus_add_driver+0xbc/0x244
[ 0.120000] [<8017aeb0>] driver_register+0xbc/0x178
[ 0.120000] [<8035efa4>] pcibios_init+0x18/0x40
[ 0.120000] [<80006500>] do_one_initcall+0xf0/0x1c0
[ 0.120000] [<8027822c>] kernel_init+0x138/0x2c0
[ 0.120000] [<8000b41c>] kernel_thread_helper+0x10/0x18
[ 0.120000]
[ 0.120000]
Code: 8c450030 3c048031 2484ddd8 <00a31824> ac430030 0c0a081e 00000000 0000000f 3c048031
[ 0.124000] ---[ end trace 139ce121c98e96c9 ]---
[ 0.128000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.128000]

Noltari · « **Respuesta #406 en:** 26-01-2013, 19:04 (Sábado) »

Vale, ya he localizado la línea en la que se cuelga.

Prueba esta imagen: https://dl.dropbox.com/u/4708147/openwrt/arv4518/openwrt-lantiq-xway-ARV4518PW-squashfs_test3.image

Perdón por el coñazo...

Lesgar · « **Respuesta #407 en:** 26-01-2013, 19:16 (Sábado) »

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.4
Created: 2013-01-26 18:03:27 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1207533 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.4 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #3 Sat Jan 26 19:03:17 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61124k/65536k available (2581k kernel code, 4412k reserved, 784k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.048000] NET: Registered protocol family 16
[ 0.068000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.072000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.080000] Debug #1
[ 0.084000] Debug #1a
[ 0.084000] Debug #2
[ 0.088000] Debug #3
[ 0.088000] Debug #4
[ 0.092000] Debug #5
[ 0.092000] Debug #5.1
[ 0.096000] Debug #5.2
[ 0.096000] Debug #5.3
[ 0.100000] Debug #5.4
[ 0.100000] Debug #5.4 (if)
[ 0.104000] Debug #5.5
[ 0.104000] Debug #5.5 (if1)
[ 0.108000] Debug #5.5 (if2)
[ 0.108000] Debug #5.6
[ 0.112000] Debug #5.6 (if1)
[ 0.112000] Debug #5.6 (if2)
[ 0.116000] Debug #5.6 (if4)
[ 0.116000] Debug #5.7
[ 0.120000] Debug #5.8
[ 0.120000] Debug #5.9
[ 0.124000] Data bus error, epc == 80281228, ra == 80281218
[ 0.124000] Oops[#1]:
[ 0.124000] Cpu 0
[ 0.124000] $ 0 : 00000000 00000000 b7000000 ffffffff
[ 0.124000] $ 4 : 8030ddf8 0000003d 0000003d 00000960
[ 0.124000] $ 8 : 00000039 00000003 803840e8 0000003d
[ 0.124000] $12 : 00000000 00000000 00000000 0000003d
[ 0.124000] $16 : 00000000 83854580 803b0000 83854590
[ 0.124000] $20 : 803b0000 81002078 803b0000 803b0000
[ 0.124000] $24 : 00000001 00000000
[ 0.124000] $28 : 8381c000 8381dd60 8032bb20 80281218
[ 0.124000] Hi : 000004b0
[ 0.124000] Lo : 000012c0
[ 0.124000] epc : 80281228 ltq_pci_probe+0x3cc/0x854
[ 0.124000] Not tainted
[ 0.124000] ra : 80281218 ltq_pci_probe+0x3bc/0x854
[ 0.124000] Status: 1100fc03 KERNEL EXL IE
[ 0.124000] Cause : 1080001c
[ 0.124000] PrId : 00019641 (MIPS 24KEc)
[ 0.124000] Modules linked in:
[ 0.124000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)
[ 0.124000] Stack : 83854598 0000003c 0000003c 00000960 0000001d 83854590 803b0000 80347894
ffffffed 8032f280 80347894 0000001d 8034c210 8017a930 83854590 80347894
80347894 8017c340 834015e0 838545c4 83854590 80347894 80347894 00000000
80380000 8017ab08 80347894 80178c1c 83853180 00000000 00000000 80347894
8017aa9c 80178f18 00000000 80275ee8 80340ae0 80178b9c 838184cc 83853430
...
[ 0.124000] Call Trace:
[ 0.124000] [<80281228>] ltq_pci_probe+0x3cc/0x854
[ 0.124000] [<8017a930>] driver_probe_device+0x138/0x2a4
[ 0.124000] [<8017ab08>] __driver_attach+0x6c/0xa4
[ 0.124000] [<80178f18>] bus_for_each_dev+0x54/0x98
[ 0.124000] [<80179ec0>] bus_add_driver+0xbc/0x244
[ 0.124000] [<8017aeb0>] driver_register+0xbc/0x178
[ 0.124000] [<8035efa4>] pcibios_init+0x18/0x40
[ 0.124000] [<80006500>] do_one_initcall+0xf0/0x1c0
[ 0.124000] [<8027822c>] kernel_init+0x138/0x2c0
[ 0.124000] [<8000b41c>] kernel_thread_helper+0x10/0x18
[ 0.124000]
[ 0.124000]
Code: 3c048031 2484ddf8 8c430004 <34630007> ac430004 0c0a0816 00000000 8e42e794 3c048031
[ 0.128000] ---[ end trace 139ce121c98e96c9 ]---
[ 0.132000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.132000]

Noltari · « **Respuesta #408 en:** 26-01-2013, 19:24 (Sábado) »

Parece como si petara al leer/escribir del bus PCI porque no está aún preparado o algo parecido :$...

Prueba esta imagen y ya te dejo en paz:
https://dl.dropbox.com/u/4708147/openwrt/arv4518/openwrt-lantiq-xway-ARV4518PW-squashfs_test4.image

A ver si blogic no está muy ocupado y le comento...

Saludos.

Lesgar · « **Respuesta #409 en:** 26-01-2013, 19:38 (Sábado) »

Aqui tienes:
----------------------------------------------
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.4
Created: 2013-01-26 18:22:28 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1207673 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.4 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Sat Jan 26 19:22:18 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61124k/65536k available (2581k kernel code, 4412k reserved, 784k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] Debug #1
[ 0.088000] Debug #1a
[ 0.088000] Debug #2
[ 0.092000] Debug #3
[ 0.092000] Debug #4
[ 0.096000] Debug #5
[ 0.096000] Debug #5.1
[ 0.100000] Debug #5.2
[ 0.100000] Debug #5.3
[ 0.104000] Debug #5.4
[ 0.104000] Debug #5.4 (if)
[ 0.108000] Debug #5.5
[ 0.108000] Debug #5.5 (if1)
[ 0.112000] Debug #5.5 (if2)
[ 0.112000] Debug #5.6
[ 0.116000] Debug #5.6 (if1)
[ 0.116000] Debug #5.6 (if2)
[ 0.120000] Debug #5.6 (if4)
[ 0.120000] Debug #5.7
[ 0.124000] Debug #5.8
[ 0.124000] Debug #5.9
[ 0.128000] Debug #5.10
[ 0.128000] Data bus error, epc == 8001cfe4, ra == 80282070
[ 0.128000] Oops[#1]:
[ 0.128000] Cpu 0
[ 0.128000] $ 0 : 00000000 00000000 80330000 80333dec
[ 0.128000] $ 4 : 00000000 ffffffff 00000000 00000000
[ 0.128000] $ 8 : 00000030 00000003 803840e8 0000003e
[ 0.128000] $12 : 00000000 00000000 00000000 0000003e
[ 0.128000] $16 : 00000000 83854580 803b0000 ffffffff
[ 0.128000] $20 : 803b0000 81002078 803b0000 8034c210
[ 0.128000] $24 : 00000002 00000000
[ 0.128000] $28 : 8381c000 8381dce8 8032bb20 80282070
[ 0.128000] Hi : 00000500
[ 0.128000] Lo : 00001400
[ 0.128000] epc : 8001cfe4 vprintk_emit+0x18/0x408
[ 0.128000] Not tainted
[ 0.128000] ra : 80282070 printk+0x38/0x44
[ 0.128000] Status: 1100fc03 KERNEL EXL IE
[ 0.128000] Cause : 0080001c
[ 0.128000] PrId : 00019641 (MIPS 24KEc)
[ 0.128000] Modules linked in:
[ 0.128000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)
[ 0.128000] Stack : 00000000 00000006 00000006 8383e580 00000000 00000000 00000000 00000000
803a412e 0000000b 00000000 8014ec3c 00000000 83854580 803b0000 83854590
803b0000 81002078 803b0000 8034c210 8032bb20 80282070 00000000 00000000
00000000 00000000 8030de08 8381dd6c 8381dd6c 803b0000 81002078 80281234
8032f280 0000003e 0000003e 00000a00 83854590 803b0000 80347894 ffffffed
...
[ 0.128000] Call Trace:
[ 0.128000] [<8001cfe4>] vprintk_emit+0x18/0x408
[ 0.128000] [<80282070>] printk+0x38/0x44
[ 0.128000] [<80281234>] ltq_pci_probe+0x3d8/0x834
[ 0.128000] [<8017a930>] driver_probe_device+0x138/0x2a4
[ 0.128000] [<8017ab08>] __driver_attach+0x6c/0xa4
[ 0.128000] [<80178f18>] bus_for_each_dev+0x54/0x98
[ 0.128000] [<80179ec0>] bus_add_driver+0xbc/0x244
[ 0.128000] [<8017aeb0>] driver_register+0xbc/0x178
[ 0.128000] [<8035efa4>] pcibios_init+0x18/0x40
[ 0.128000] [<80006500>] do_one_initcall+0xf0/0x1c0
[ 0.128000] [<8027822c>] kernel_init+0x138/0x2c0
[ 0.128000] [<8000b41c>] kernel_thread_helper+0x10/0x18
[ 0.128000]
[ 0.128000]
Code: 8c50f30c afbe0050 afb40040 <afb3003c> afbf0054 afb7004c afb60048 afb50044 afb20038
[ 0.132000] ---[ end trace 139ce121c98e96c9 ]---
[ 0.136000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.136000]
-------------------------------------------------------------

Para nada molestas, todo lo contrario, muchas gracias por intentarlo. Si hablas con blogic comentale si quere que le envie el arv7519rw22 a su casa para que lo porte a openwrt. que a mi no me contesta.

Noltari · « **Respuesta #410 en:** 26-01-2013, 19:46 (Sábado) »

Por lo que veo en el último log ha petado en una simple lectura de la memoria...

Esto me lleva a pensar que el PCI no está correctamente inicializado, porque no tiene sentido alguno que los registros de memoria del bus PCI no sean correctos, dado que funcionan en toda los dispositivos danube.

Noltari · « **Respuesta #411 en:** 26-01-2013, 22:59 (Sábado) »

Todavía no he podido hablar con blogic, pero se me ha ocurrido una cosa que igual tiene algún efecto:
https://dl.dropbox.com/u/4708147/openwrt/arv4518/openwrt-lantiq-xway-ARV4518PW-squashfs_test5.image

Pruébalo y me cuentas

.

Saludos!

Lesgar · « **Respuesta #412 en:** 26-01-2013, 23:54 (Sábado) »

Sigue petando:

ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.4
Created: 2013-01-26 21:56:50 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1207248 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.4 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #5 Sat Jan 26 22:56:40 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61124k/65536k available (2581k kernel code, 4412k reserved, 784k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] Debug #1
[ 0.088000] Debug #1a
[ 0.088000] Debug #2
[ 0.092000] Debug #3
[ 0.092000] Debug #4
[ 0.096000] Debug #5
[ 0.096000] Debug #5.1
[ 0.100000] Debug #5.2
[ 0.100000] Debug #5.3
[ 0.104000] Debug #5.4
[ 0.104000] Debug #5.4 (if)
[ 0.108000] Debug #5.5
[ 0.108000] Debug #5.5 (if1)
[ 0.112000] Debug #5.5 (if2)
[ 0.112000] Debug #5.6
[ 0.116000] Debug #5.6 (if1)
[ 0.116000] Debug #5.6 (if2)
[ 0.120000] Debug #5.6 (if4)
[ 0.124000] Debug #5.7
[ 0.124000] Data bus error, epc == 8028122c, ra == 80281214
[ 0.124000] Oops[#1]:
[ 0.124000] Cpu 0
[ 0.124000] $ 0 : 00000000 00000000 be105400 feffffff
[ 0.124000] $ 4 : 8030ddd8 ffffffff 0000003b 000009b0
[ 0.124000] $ 8 : 00000037 00000003 803840e8 0000003b
[ 0.124000] $12 : 00000000 00000000 00000000 0000003b
[ 0.124000] $16 : 00000000 83854580 803b0000 83854590
[ 0.124000] $20 : 803b0000 81002078 803b0000 803b0000
[ 0.124000] $24 : 00000001 00000000
[ 0.124000] $28 : 8381c000 8381dd60 8032bb20 80281214
[ 0.124000] Hi : 000004d8
[ 0.124000] Lo : 00001360
[ 0.124000] epc : 8028122c ltq_pci_probe+0x3d0/0x888
[ 0.124000] Not tainted
[ 0.124000] ra : 80281214 ltq_pci_probe+0x3b8/0x888
[ 0.124000] Status: 1100fc03 KERNEL EXL IE
[ 0.124000] Cause : 1080001c
[ 0.124000] PrId : 00019641 (MIPS 24KEc)
[ 0.124000] Modules linked in:
[ 0.124000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)
[ 0.124000] Stack : 83854598 0001adb0 00000250 00000960 0000001d 83854590 803b0000 80347894
ffffffed 8032f280 80347894 0000001d 8034c210 8017a930 83854590 80347894
80347894 8017c340 834015e0 838545c4 83854590 80347894 80347894 00000000
80380000 8017ab08 80347894 80178c1c 83853180 00000000 00000000 80347894
8017aa9c 80178f18 00000000 80275ee8 80340ae0 80178b9c 838184cc 83853430
...
[ 0.124000] Call Trace:
[ 0.124000] [<8028122c>] ltq_pci_probe+0x3d0/0x888
[ 0.124000] [<8017a930>] driver_probe_device+0x138/0x2a4
[ 0.124000] [<8017ab08>] __driver_attach+0x6c/0xa4
[ 0.124000] [<80178f18>] bus_for_each_dev+0x54/0x98
[ 0.124000] [<80179ec0>] bus_add_driver+0xbc/0x244
[ 0.124000] [<8017aeb0>] driver_register+0xbc/0x178
[ 0.124000] [<8035efa4>] pcibios_init+0x18/0x40
[ 0.124000] [<80006500>] do_one_initcall+0xf0/0x1c0
[ 0.124000] [<8027822c>] kernel_init+0x138/0x2c0
[ 0.124000] [<8000b41c>] kernel_thread_helper+0x10/0x18
[ 0.124000]
[ 0.124000]
Code: 8c450030 3c048031 2484ddd8 <00a31824> ac430030 0c0a0823 00000000 0000000f 3c048031
[ 0.128000] ---[ end trace 139ce121c98e96c9 ]---
[ 0.132000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.132000]

brunorro · « **Respuesta #413 en:** 27-01-2013, 10:13 (Domingo) »

Buenas !!

Tengo también por aquí un ARV4518PW con el que estoy intentando compilar el trunk (en el curro tengo un quad core con el que en menos de media hora lo tengo). A parte de los panics estándar, comentar que cuando se quita el soporte para PCI no monta root. A ver si os puedo colgar por aquí el log en algún momento...

Como off-topic, comentar que lo que más paloter me pone de este kernel es el soporte para zram. Si con el tema de compresión podemos ganarle unos megas al cacharro, aún a costa de hacerle perder algo de CPU, transmission y demás servicios "not real time" irán mucho mejor. Otra cosa que me pregunto si conseguirá compilar correctamente es la librería polarssl, porque si consiguen que el cliente sea 100% compatible con el VPN normal tendremos un cliente/server openvpn con un consumo de memoria muuuuuuy inferior.

Y como segundo off-topic del día, he conseguido hacer funcionar la VoIP con CSIPsimple en el móvil. Colgaré un post explicativo en el hilo pertinente... Pero ya os digo que el truco fundamental es no hacer currar al DNS para atacar al dominio.

Lo siguiente que quería hacer es usar el router como acceso al SIP de orange y tener el fijo desde todo lugar en el que tenga internet, pero sólo como ejercicio didáctico porque:

a) Desconozco la legalidad del asunto y
b) esta gente usa como códecs G.711 y G.722, ambos de 64kbps, que van finos pero suben la factura de datos cosa mala....

Gracias a todos por el currazo que os estáis pegando !

Noltari · « **Respuesta #414 en:** 27-01-2013, 13:48 (Domingo) »

Lesgar, esta imagen va con ayuda de blogic.
https://dl.dropbox.com/u/4708147/openwrt/arv4518/openwrt-lantiq-xway-ARV4518PW-squashfs_blogic.image

No le he podido preguntar sobre si le enviabas el ARV7519 porque está un poco susceptible y está bastante ocupado.

EDIT: Si no tira excepción prueba el WiFi.

Saludos.

sephir0t00 · « **Respuesta #415 en:** 27-01-2013, 16:52 (Domingo) »

Noltari, esta imagen ya funciona correctamente, no da ningún error, funciona la wifi, los cambios son persistentes y el usb lo reconoce.
A ver si lo prueba Lesgar y le da el mismo resultado que a mí.

Muchas gracias a Pteridium, Noltari, Lesgar y blogic, por el esfuerzo realizado, ^^

A continuación el bootlog:
https://dl.dropbox.com/u/18460228/openwrt/ARV4518-R01_noltari-blogic.log

Lesgar · « **Respuesta #416 en:** 27-01-2013, 17:19 (Domingo) »

A mi también me funciona, pero no va la wifi. Como la has activado? En Luci no aparece, con el comando wifi tampoco, tampoco con el ifconfig. Me parece que me he cargado los datos de calibración de la wifi (los que están en los últimos 64k). Aunque tengo una copia entera de la flash no se cómo cargar SOLAMENTE esa particion

Yo_Julio · « **Respuesta #417 en:** 27-01-2013, 18:01 (Domingo) »

Bueno después de dejarlo casi tostado, ya he conseguido cargar uboot y un firmware que (al menos) arranca: atitude.adjustment

Como no queria soldar busque un programita que tenía para dialogar por el puerto serie de los tiempos del ms-dos, pero al final me harté de rebuscar entre disquetes polvorientos y metí el soldador.
Eso sí, nada más terminar descubrí que a alguien ya se la había ocurrido. Si a algien le pasa y no quiere soldar para ponerlo en modo UART que mire aquí antes (no después, como yo)

https://forum.openwrt.org/viewtopic.php?pid=183315#p183315

En cuanto a la imagen que acabas de colgar openwrt-lantiq-xway-ARV4518PW-squashfs_blogic.image en el mío no va (es un R01A)

pongo las ultimas lineas de la salida de putty por si sirve de algo. He puesto en cursiva las que se diferencian del log que acaba de postear sephir0t00 Lo demás está igual.

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00013ec0
[ 0.000000] Readback ErrCtl register=00013ec0
[ 0.000000] Memory: 61124k/65536k available (2580k kernel code, 4412k reserved, 785k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.048000] NET: Registered protocol family 16
[ 0.068000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.072000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.088000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.092000] IO 0x000000001ae00000..0x000000001affffff
[ 0.116000] bio: create slab <bio-0> at 0
[ 0.124000] usbcore: registered new interface driver usbfs
[ 0.128000] usbcore: registered new interface driver hub
[ 0.132000] usbcore: registered new device driver usb
[ 0.136000] PCI host bridge to bus 0000:00
[ 0.140000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.144000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.148000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

Y aquí se queda colgado.

Noltari · « **Respuesta #418 en:** 27-01-2013, 18:12 (Domingo) »

Lo primero es daros las gracias a vosotros por las pruebas

.

Cita de: Lesgar en 27-01-2013, 17:19 (Domingo)

A mi también me funciona, pero no va la wifi. Como la has activado? En Luci no aparece, con el comando wifi tampoco, tampoco con el ifconfig. Me parece que me he cargado los datos de calibración de la wifi (los que están en los últimos 64k). Aunque tengo una copia entera de la flash no se cómo cargar SOLAMENTE esa particion

Mándame el backup a mi correo (noltari@gmail.com), extraigo la partición boardconfig y te la mando junto con un firmware que tenga la protección de la partición desactivada para poder flashearla.

Cita de: Yo_Julio en 27-01-2013, 18:01 (Domingo)

Bueno después de dejarlo casi tostado, ya he conseguido cargar uboot y un firmware que (al menos) arranca: atitude.adjustment

Como no queria soldar busque un programita que tenía para dialogar por el puerto serie de los tiempos del ms-dos, pero al final me harté de rebuscar entre disquetes polvorientos y metí el soldador.
Eso sí, nada más terminar descubrí que a alguien ya se la había ocurrido. Si a algien le pasa y no quiere soldar para ponerlo en modo UART que mire aquí antes (no después, como yo)

https://forum.openwrt.org/viewtopic.php?pid=183315#p183315

En cuanto a la imagen que acabas de colgar openwrt-lantiq-xway-ARV4518PW-squashfs_blogic.image en el mío no va (es un R01A)

pongo las ultimas lineas de la salida de putty por si sirve de algo. He puesto en cursiva las que se diferencian del log que acaba de postear sephir0t00 Lo demás está igual.

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00013ec0
[ 0.000000] Readback ErrCtl register=00013ec0
[ 0.000000] Memory: 61124k/65536k available (2580k kernel code, 4412k reserved, 785k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.048000] NET: Registered protocol family 16
[ 0.068000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.072000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.088000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.092000] IO 0x000000001ae00000..0x000000001affffff
[ 0.116000] bio: create slab <bio-0> at 0
[ 0.124000] usbcore: registered new interface driver usbfs
[ 0.128000] usbcore: registered new interface driver hub
[ 0.132000] usbcore: registered new device driver usb
[ 0.136000] PCI host bridge to bus 0000:00
[ 0.140000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.144000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.148000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

Y aquí se queda colgado.

Gracias por las pruebas, aunque ya lo había probado Pteridium y no funcionaba en el R01A. Hay que hacer dos DTS distintos, ya estoy preparando el parche para mandarlo.

Saludos.

sephir0t00 · « **Respuesta #419 en:** 27-01-2013, 18:20 (Domingo) »

Lesgar pues he activado la wifi de forma normal a través de luci.
A ver si se te arregla restaurando los datos de calibración.

Noticias:

Autor Tema: [Desarrollo] OpenWRT para routers Astoria de ya.com (ARV4518/ARV7518) (Leído 699211 veces)

Pteridium

Lesgar

Noltari

Lesgar

Noltari

Lesgar

Noltari

Lesgar

Noltari

Lesgar

Noltari

Noltari

Lesgar

brunorro

Noltari

sephir0t00

Lesgar

Yo_Julio

Noltari

sephir0t00