Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a (Leído 2230096 veces)

masuele · « **Respuesta #1460 en:** 20-05-2013, 21:19 (Lunes) »

Cita de: jar229 en 20-05-2013, 08:10 (Lunes)

En el apartado LAN tienes mal configuradas un par de cosas

En gateway debes poner 192.168.1.1 (en lugar de 192.168.100.1 )
Máscara de red 255.255.255.0 (en lugar de 255.255.240.0 )

Qué compilación estás usando ?

EDITO: en la 5ª captura que has puesto, en el apartado WWAN te sigue saliendo un IP pública

aver el gateway es 192.168.100.1 por que es el de mi router principal y la mascara de red tambien es 255.255.240.0 en mi router principal y que sepa no habia que poner en estos dos apartados los mismo que mi router principal?, bien pero pa la wwan como le pongo una ip fija? que se la pueda escribir yo y guardarlo, de todas formas ya te digo por cable si tengo internet se va cuando activo la red repetidora. Tengo la ultima compilacion que posteaste jar pues tenia una cocon todo para usbs pero nose a veces se ponia lento el router asique eti esta. hg556a_backport_12.09-luci.zip

jar229 · « **Respuesta #1461 en:** 20-05-2013, 22:00 (Lunes) »

Tienes un lío bastante gordo. La parte LAN, no tiene nada que ver con la de tu router principal (los equipos van a estar en dos subredes distintas).
Si estás usando el backport a backfire, para que te funcione el modo repetidor, tienes que desactivar la WiFi y volverla a activar.

Pero sigo diciendo que me resulta muy raro que en WWAN recibas una IP pública. Creo que sigues sin tener bien configurado el router de Ono ... $:-\$

Y este tema debería ser tratado en el hilo pertinente. Si vuelves a postear aquí tratando del modo/cliente/repetidor te lo borraré sin más ... :o

Enviado desde mi Cube U30GT

masuele · « **Respuesta #1462 en:** 20-05-2013, 23:45 (Lunes) »

He posteado donde dices, ya no lo hago mas aqui pa eso que los correos me llega la respuesta en este tema por eso segui contestando aqui, solo una cosa tambien tengo un par de routers o nose que son, se que se usaban pa repetir señales en un colegio pero no se utilizarlos

usr 5441

3crgpoe10075

Son estos dos me sevirian para algo? y mas de alguna vez intente utilizarlos como indican sus manuales pero nada... y se que es por mi torpeza como al principio con el router este de vodafone que pensaba que ya lo habia jodido bien y no era nada.

zanuksi · « **Respuesta #1463 en:** 21-05-2013, 02:51 (Martes) »

Hola buenas noches a todos, Gracias de antemano, ya que creo que hago bien en postear aquí, sino mis disculpas al moderador (soy un poco nuevo en esto)

Os escribo porque hace unos días instale adsl de Telefónica en mi casa (4 plantas de altura), el problema que tengo es el siguiente: Yo antes tenia VF y tengo el router HG556a (Ver. A) con chipset Ralink. El router de Movistar esta en el salón (Planta 4ª) y el HG556A en la (Planta 1ª), tiene instalado ya el Openwrt r36114 y en el puerto usb una antena AWVS036NH que me autorecomende porque por lo que e leído este modelo de router no envía y recibe a la vez (corregidme si me equivoco). El tema es que el Openwrt me reconoce la antena pero al ponerla en modo cliente directamente se apaga y no encuentra la red. ¿Que estoy haciendo mal? Repito Gracias de antemano, llevo muchos días con esto desde las sombras y al final necesito vuestra ayuda $:-\$

jar229 · « **Respuesta #1464 en:** 21-05-2013, 08:20 (Martes) »

masuele: los dos equipos que comentas, permiten ampliar una red wifi, usando WDS.

zanuksi: has probado a usar la wifi interna del hg556a como cliente, y la ralink en modo AP ?

Has probado los otros dos puertos USB ?

Pon la salida del dmesg por aquí, a ver si vemos algo ...

zanuksi · « **Respuesta #1465 en:** 21-05-2013, 13:05 (Martes) »

la verdad tengo el dmesg copiado pero como lo añado para no estropearte el hilo (sea una ventana aparte o algo parecido, porque como spoiler no me lo coloca), gracias!

jar229 · « **Respuesta #1466 en:** 21-05-2013, 13:22 (Martes) »

Utiliza las etiquetas

Código: [Seleccionar]

[quote][/quote]
Y no olvides responder al resto de preguntas

zanuksi · « **Respuesta #1467 en:** 21-05-2013, 13:38 (Martes) »

Citar

root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.7.10 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Sun Mar 24 19:12:50 CET 2013
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] bcm63xx_nvram: nvram checksum invalid (expected 33313530, actual 55562450)
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802cdd60, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 61464k/65536k available (2296k kernel code, 4072k reserved, 594k data, 244k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.036000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.064000] registering PCI controller with io_map_base unset
[ 0.084000] bio: create slab <bio-0> at 0
[ 0.092000] PCI host bridge to bus 0000:00
[ 0.096000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.100000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.104000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.108000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff]
[ 0.120000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.120000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.140000] NET: Registered protocol family 2
[ 0.144000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.152000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.160000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.164000] TCP: reno registered
[ 0.168000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.176000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] NET: Registered protocol family 1
[ 0.188000] PCI: CLS 0 bytes, default 16
[ 0.192000] audit: initializing netlink socket (disabled)
[ 0.196000] type=2000 audit(0.195:1): initialized
[ 0.204000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.208000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.220000] msgmni has been set to 120
[ 0.224000] io scheduler noop registered
[ 0.228000] io scheduler deadline registered (default)
[ 0.236000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.244000] console [ttyS0] enabled, bootconsole disabled
[ 0.260000] physmap platform flash device: 02000000 at 1e000000
[ 0.268000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.280000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.280000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.284000] Amd/Fujitsu Extended Query version 1.3.
[ 0.288000] number of CFI chips: 1
[ 0.292000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.300000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.308000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[ 0.316000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length cc0000
[ 0.324000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 20000
[ 0.328000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.336000] bcm63xxpart: Partition 5 is linux offset 20000 and length de0000
[ 0.344000] bcm63xxpart: Spare partition is offset 420004 and length 9dfffc
[ 0.352000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.360000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.364000] 0x000000000000-0x000000020000 : "CFE"
[ 0.372000] 0x000000020100-0x000000140000 : "kernel"
[ 0.380000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.396000] 0x000000140000-0x000000e00000 : "rootfs"
[ 0.404000] mtd: partition "rootfs" set to be root filesystem
[ 0.412000] mtd: partition "rootfs_data" created automatically, ofs=420000, len=9E0000
[ 0.420000] 0x000000420000-0x000000e00000 : "rootfs_data"
[ 0.428000] 0x000000e00000-0x000000e20000 : "cal_data"
[ 0.440000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.448000] 0x000000020000-0x000000e00000 : "linux"
[ 0.460000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542) v0.1.2
[ 0.480000] libphy: bcm63xx_enet MII bus: probed
[ 0.484000] b53_common: found switch: BCM5325, rev 0
[ 0.492000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[ 0.504000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.512000] Registered led device: HW556:red:message
[ 0.512000] Registered led device: HW556:red:hspa
[ 0.512000] Registered led device: HW556:red:dsl
[ 0.516000] Registered led device: HW556:red:power
[ 0.516000] Registered led device: HW556:red:all
[ 0.520000] TCP: cubic registered
[ 0.520000] NET: Registered protocol family 17
[ 0.528000] 8021q: 802.1Q VLAN Support v1.8
[ 0.544000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.552000] Freeing unused kernel memory: 244k freed
[ 4.180000] Button Hotplug driver version 0.4.1
[ 4.216000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 5.632000] eth0: link UP - 100/full - flow control off
[ 7.932000] jffs2: notice: (349) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found.
[ 8.700000] eth0: link DOWN
[ 11.684000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[ 11.692000] Backport based on wireless-testing.git master-2013-02-22
[ 11.700000] compat.git: wireless-testing.git
[ 11.768000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.776000] cfg80211: World regulatory domain updated:
[ 11.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.788000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.796000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.804000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.812000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.820000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.484000] SCSI subsystem initialized
[ 12.748000] usbcore: registered new interface driver usbfs
[ 12.752000] usbcore: registered new interface driver hub
[ 12.760000] usbcore: registered new device driver usb
[ 12.952000] lib80211: common routines for IEEE802.11 drivers
[ 12.960000] lib80211_crypt: registered algorithm 'NULL'
[ 12.988000] lib80211_crypt: registered algorithm 'WEP'
[ 13.020000] lib80211_crypt: registered algorithm 'CCMP'
[ 13.048000] lib80211_crypt: registered algorithm 'TKIP'
[ 14.496000] usbcore: registered new interface driver usb8xxx
[ 14.672000] usbcore: registered new interface driver rt2500usb
[ 14.852000] usbcore: registered new interface driver rt73usb
[ 14.900000] usbcore: registered new interface driver rtl8187
[ 15.092000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.100000] rt2800pci 0000:00:01.0: setting latency timer to 64
[ 15.116000] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 3572, rf: 0001, rev: 0223.
[ 15.124000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.128000] Registered led device: rt2800pci-phy0::radio
[ 15.128000] Registered led device: rt2800pci-phy0::assoc
[ 15.128000] Registered led device: rt2800pci-phy0::quality
[ 15.164000] usbcore: registered new interface driver rt2800usb
[ 16.512000] PPP generic driver version 2.4.2
[ 16.584000] usbcore: registered new interface driver p54usb
[ 16.988000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.288000] NET: Registered protocol family 24
[ 17.520000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.632000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 17.636000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 17.672000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 17.688000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 17.696000] hub 1-0:1.0: USB hub found
[ 17.700000] hub 1-0:1.0: 2 ports detected
[ 17.908000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[ 18.388000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[ 19.264000] usb 1-1: reset high-speed USB device number 2 using bcm63xx_ehci
[ 19.492000] usbcore: registered new interface driver ath9k_htc
[ 19.552000] usbcore: registered new interface driver brcmfmac
[ 19.704000] usbcore: registered new interface driver carl9170
[ 19.896000] usbcore: registered new interface driver zd1201
[ 20.100000] Initializing USB Mass Storage driver...
[ 20.104000] usbcore: registered new interface driver usb-storage
[ 20.112000] USB Mass Storage support registered.
[ 20.308000] usbcore: registered new interface driver zd1211rw
[ 20.356000] phy1 -> rt2x00_set_chip: Info - Chipset detected - rt: 3070, rf: 0005, rev: 0201.
[ 20.372000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 20.376000] Registered led device: rt2800usb-phy1::radio
[ 20.376000] Registered led device: rt2800usb-phy1::assoc
[ 20.376000] Registered led device: rt2800usb-phy1::quality
[ 20.488000] usb 1-2: new high-speed USB device number 3 using bcm63xx_ehci
[ 20.628000] hub 1-2:1.0: USB hub found
[ 20.632000] hub 1-2:1.0: 4 ports detected
[ 26.036000] eth0: link UP - 100/full - flow control off
[ 27.528000] device eth0.1 entered promiscuous mode
[ 27.536000] device eth0 entered promiscuous mode
[ 27.548000] br-lan: port 1(eth0.1) entered forwarding state
[ 27.552000] br-lan: port 1(eth0.1) entered forwarding state
[ 29.040000] eth0: link UP - 100/full - flow control off
[ 29.556000] br-lan: port 1(eth0.1) entered forwarding state
[ 33.996000] phy0 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'.
[ 34.308000] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34.
[ 34.412000] device wlan0 entered promiscuous mode
[ 34.520000] br-lan: port 2(wlan0) entered forwarding state
[ 34.524000] br-lan: port 2(wlan0) entered forwarding state
[ 36.528000] br-lan: port 2(wlan0) entered forwarding state
[ 37.840000] cfg80211: Calling CRDA for country: ES
[ 37.848000] cfg80211: Regulatory domain changed to country: ES
[ 37.852000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 37.860000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 37.868000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 37.876000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 37.884000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 40.412000] phy1 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
[ 40.424000] phy1 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29.
[ 41.024000] device wlan1 entered promiscuous mode
[ 41.648000] br-lan: port 3(wlan1) entered forwarding state
[ 41.656000] br-lan: port 3(wlan1) entered forwarding state
[ 43.660000] br-lan: port 3(wlan1) entered forwarding state
[ 142.240000] device wlan0 left promiscuous mode
[ 142.244000] br-lan: port 2(wlan0) entered disabled state
[ 143.176000] device wlan1 left promiscuous mode
[ 143.184000] br-lan: port 3(wlan1) entered disabled state
[ 146.508000] cfg80211: Calling CRDA to update world regulatory domain
[ 146.516000] cfg80211: World regulatory domain updated:
[ 146.520000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 146.528000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 146.536000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 146.544000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 146.552000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 146.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 150.444000] cfg80211: Calling CRDA for country: ES
[ 150.448000] cfg80211: Regulatory domain changed to country: ES
[ 150.456000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 150.464000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 150.472000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 150.480000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 150.488000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 154.308000] device wlan1 entered promiscuous mode
[ 155.216000] br-lan: port 2(wlan1) entered forwarding state
[ 155.224000] br-lan: port 2(wlan1) entered forwarding state
[ 157.228000] br-lan: port 2(wlan1) entered forwarding state
[ 159.932000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 0
[ 159.940000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 0
[ 159.952000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 0
[ 159.960000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 0
[ 159.968000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 0
[ 190.340000] device wlan1 left promiscuous mode
[ 190.348000] br-lan: port 2(wlan1) entered disabled state
[ 191.564000] cfg80211: Calling CRDA to update world regulatory domain
[ 191.572000] cfg80211: World regulatory domain updated:
[ 191.576000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 191.584000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 191.592000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 191.600000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 191.608000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 191.616000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 194.704000] cfg80211: Calling CRDA for country: ES
[ 194.708000] cfg80211: Regulatory domain changed to country: ES
[ 194.716000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 194.724000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 194.732000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 194.740000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 194.748000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 198.284000] device wlan1 entered promiscuous mode
[ 198.924000] br-lan: port 2(wlan1) entered forwarding state
[ 198.932000] br-lan: port 2(wlan1) entered forwarding state
[ 200.936000] br-lan: port 2(wlan1) entered forwarding state
[ 220.056000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 0
[ 220.064000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 0
[ 220.076000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 0
[ 220.084000] phy1 -> rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 0
root@OpenWrt:~#

OK, si e probado en los 3 con el mismo resultado. Lo extraño es que cuando pongo en modo cliente la interna del HG556a también me la des habilita le doy a enable la reinicia pero no consigue conectar. Madre mía que desesperación!!!

jar229 · « **Respuesta #1468 en:** 21-05-2013, 14:12 (Martes) »

Prueba a instalar la compilación r35318: https://dl.dropbox.com/u/4708147/openwrt/bcm63xx/HG556a/openwrt-HW556-squashfs-cfe_r35318.bin

zanuksi · « **Respuesta #1469 en:** 21-05-2013, 17:44 (Martes) »

Al final e conseguido conectar con la compilacion actual, con un simple reset y cambiando al usb trasero fue suficiente. El problema es que el wifi del router no emite, tan solo me da conexion por Lan, a que puede ser debido. Mil gracias de corazon!!

jar229 · « **Respuesta #1470 en:** 21-05-2013, 20:47 (Martes) »

Yo probría con la compilación que te comenté anteriormente.
En modo cliente tampoco te funciona la wifi ?
No te estarás liando con la configuración ?

dlop · « **Respuesta #1471 en:** 21-05-2013, 20:55 (Martes) »

Hola.

Un problemilla:
Llevo unos dias intentado reinstalar el Openwrt en el HG556a, y siempre me falta algo:
- He probado igual que cuando el kernel er 3.3.8, pero con el firm R36114, con el R35318 y con el trunk... pero los repositorios ya han cambiado a kernel 3.8 y no admite lo de la impresora.
- Y he probado tambien con el firm de attitude adjustment 12.09 y con el trunk... pero ahí el problema es con la wifi, que no aparece.

- ¿Alguna solución, o teneis previsto alguna versión con el kernel actual?

Esta es mi secuencia de instalación ahora

Citar

1.- Descargar imagen nueva
2.- Instalar imagen (interfaz web) "openwrt-HW556-squashfs-cfe_20130521.bin"
3.- Acceder por telnet
4.- Asignar password y modificar ip y gateway, y reiniciar network
5.- Conectar por SSH
6.- Modificar el dns: vi /etc/resolv .. 8.8.8.8
7.- Reiniciar network: /etc/init.d/network restart
8.- opkg install luci (y baja un montón de cosas)
9- /etc/init.d/uhttpd start
10.- /etc/init.d/uhttpd enable
11.- Conectar por web (ha cambiado a tipo "bootstrap")

Adjunto el log del Kernel con "openwrt-HW556-squashfs-cfe.bin" Barrier Breaker r36676 (he vuelto a probar el antiguo y no da errores)

Citar

================
[ 0.000000] Linux version 3.8.12 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36676) ) #1 Tue May 21 05:53:28 PDT 2013
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 33303639, got bb7c4910)
[ 0.000000] No bcm_tag found!
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556_C
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8030aaf0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 61236k/65536k available (2440k kernel code, 4300k reserved, 693k data, 256k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.036000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.064000] registering PCI controller with io_map_base unset
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff]
[ 0.108000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.112000] pci 0000:00:01.0: [168c:ff1d] type 00 class 0x020000
[ 0.112000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.124000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.124000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.128000] PCI host bridge to bus 0000:01
[ 0.132000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[ 0.136000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff]
[ 0.140000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.144000] pci 0000:01:1e.0: [14e4:6358] type 02 class 0x060700
[ 0.144000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.148000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
[ 0.148000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 05
[ 0.148000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[ 0.152000] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff]
[ 0.156000] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff]
[ 0.160000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[ 0.164000] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff]
[ 0.168000] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff]
[ 0.172000] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff]
[ 0.176000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
[ 0.180000] pci 0000:01:1e.0: setting latency timer to 64
[ 0.180000] Switching to clocksource MIPS
[ 0.192000] NET: Registered protocol family 2
[ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.204000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.212000] TCP: Hash tables configured (established 512 bind 512)
[ 0.220000] TCP: reno registered
[ 0.224000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.236000] NET: Registered protocol family 1
[ 0.240000] pci 0000:00:01.0: fixup device configuration
[ 0.248000] PCI: CLS 0 bytes, default 16
[ 0.256000] audit: initializing netlink socket (disabled)
[ 0.260000] type=2000 audit(0.259:1): initialized
[ 0.264000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.272000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.284000] msgmni has been set to 119
[ 0.288000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.296000] io scheduler noop registered
[ 0.300000] io scheduler deadline registered (default)
[ 0.308000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.316000] console [ttyS0] enabled, bootconsole disabled
[ 0.332000] physmap platform flash device: 02000000 at 1e000000
[ 0.340000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.352000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.352000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.356000] Amd/Fujitsu Extended Query version 1.3.
[ 0.360000] number of CFI chips: 1
[ 0.364000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.372000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.380000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[ 0.388000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length da0000
[ 0.392000] bcm63xxpart: Partition 3 is cal_data offset ee0000 and length 20000
[ 0.400000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.408000] bcm63xxpart: Partition 5 is linux offset 20000 and length ec0000
[ 0.416000] bcm63xxpart: Spare partition is offset 2e0004 and length bffffc
[ 0.424000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.428000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.436000] 0x000000000000-0x000000020000 : "CFE"
[ 0.444000] 0x000000020100-0x000000140000 : "kernel"
[ 0.448000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.468000] 0x000000140000-0x000000ee0000 : "rootfs"
[ 0.476000] mtd: partition "rootfs" set to be root filesystem
[ 0.480000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=C00000
[ 0.488000] 0x0000002e0000-0x000000ee0000 : "rootfs_data"
[ 0.500000] 0x000000ee0000-0x000000f00000 : "cal_data"
[ 0.508000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.516000] 0x000000020000-0x000000ee0000 : "linux"
[ 0.528000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[ 0.548000] libphy: bcm63xx_enet MII bus: probed
[ 0.552000] b53_common: found switch: BCM5325, rev 0
[ 0.560000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[ 0.572000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.584000] TCP: cubic registered
[ 0.588000] NET: Registered protocol family 17
[ 0.596000] Bridge firewalling registered
[ 0.600000] 8021q: 802.1Q VLAN Support v1.8
[ 0.616000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.628000] Freeing unused kernel memory: 256k freed
[ 4.300000] Button Hotplug driver version 0.4.1
[ 4.332000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 5.652000] eth0: link UP - 100/full - flow control off
[ 8.676000] eth0: link DOWN
[ 9.716000] compat-drivers backport release: compat-drivers-2013-03-28-5
[ 9.720000] Backport based on wireless-testing.git master-2013-04-16
[ 9.728000] compat.git: wireless-testing.git
[ 9.796000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.800000] cfg80211: World regulatory domain updated:
[ 9.808000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.816000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.824000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.832000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.840000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.848000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.300000] NET: Registered protocol family 10
[ 11.096000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 11.304000] PPP generic driver version 2.4.2
[ 11.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.832000] NET: Registered protocol family 24
[ 11.876000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 12.396000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.948000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.672000] eth0: link UP - 100/full - flow control off
[ 19.676000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.536000] device eth0.1 entered promiscuous mode
[ 21.540000] device eth0 entered promiscuous mode
[ 21.552000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.556000] br-lan: port 1(eth0.1) entered forwarding state
[ 22.576000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 22.676000] eth0: link UP - 100/full - flow control off
[ 23.560000] br-lan: port 1(eth0.1) entered forwarding state
[ 34.888000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 34.904000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 34.908000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 107.228000] jffs2: notice: (757) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 180.016000] br-lan: port 1(eth0.1) entered disabled state
[ 180.028000] device eth0.1 left promiscuous mode
[ 180.032000] device eth0 left promiscuous mode
[ 180.036000] br-lan: port 1(eth0.1) entered disabled state
[ 180.708000] eth0: link DOWN
[ 181.408000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 182.708000] eth0: link UP - 100/full - flow control off
[ 182.712000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 183.448000] device eth0.1 entered promiscuous mode
[ 183.452000] device eth0 entered promiscuous mode
[ 183.464000] br-lan: port 1(eth0.1) entered forwarding state
[ 183.468000] br-lan: port 1(eth0.1) entered forwarding state
[ 183.712000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 184.712000] eth0: link UP - 100/full - flow control off
[ 185.472000] br-lan: port 1(eth0.1) entered forwarding state

Ahora el log con la versión antigua (kernel 3.3.

Citar

Kernel log en R33456
================
[ 0.000000] Linux version 3.3.8 (jar@jar-virtual-machine) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Sep 18 19:36:08 CEST 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-49.46
[ 0.000000] HW556: ath9k caldata offset 0xefe000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW556
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802afd70, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61800k/65536k available (2279k kernel code, 3736k reserved, 409k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.108000] pci 0000:00:01.0: [168c:ff1d] type 0 class 0x000200
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] NET: Registered protocol family 2
[ 0.140000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.148000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.156000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.164000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.172000] TCP reno registered
[ 0.172000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] pci 0000:00:01.0: fixup device configuration
[ 0.200000] PCI: CLS 0 bytes, default 16
[ 0.204000] audit: initializing netlink socket (disabled)
[ 0.212000] type=2000 audit(0.212:1): initialized
[ 0.216000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.224000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.236000] msgmni has been set to 120
[ 0.240000] io scheduler noop registered
[ 0.244000] io scheduler deadline registered (default)
[ 0.252000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.260000] console [ttyS0] enabled, bootconsole disabled
[ 0.276000] physmap platform flash device: 02000000 at 1e000000
[ 0.284000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.292000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.292000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.300000] Amd/Fujitsu Extended Query version 1.3.
[ 0.304000] number of CFI chips: 1
[ 0.308000] bcm63xxpart: CFE boot tag found with version 8 and board type HW556
[ 0.316000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.320000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.328000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ce0000
[ 0.336000] bcm63xxpart: Partition 3 is cal_data offset e00000 and length 1e0000
[ 0.344000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.352000] bcm63xxpart: Partition 5 is linux offset 20000 and length de0000
[ 0.360000] bcm63xxpart: Spare partition is offset 5c0004 and length 83fffc
[ 0.368000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.372000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.380000] 0x000000000000-0x000000020000 : "CFE"
[ 0.388000] 0x000000020100-0x000000120000 : "kernel"
[ 0.392000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.408000] 0x000000120000-0x000000e00000 : "rootfs"
[ 0.420000] mtd: partition "rootfs" set to be root filesystem
[ 0.424000] mtd: partition "rootfs_data" created automatically, ofs=5C0000, len=840000
[ 0.432000] 0x0000005c0000-0x000000e00000 : "rootfs_data"
[ 0.444000] 0x000000e00000-0x000000fe0000 : "cal_data"
[ 0.452000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.460000] 0x000000020000-0x000000e00000 : "linux"
[ 0.480000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.488000] Registered led device: HW556:red:message
[ 0.492000] Registered led device: HW556:red:hspa
[ 0.492000] Registered led device: HW556:red:dsl
[ 0.492000] Registered led device: HW556:red:power
[ 0.492000] Registered led device: HW556:red:all
[ 0.496000] TCP cubic registered
[ 0.496000] NET: Registered protocol family 17
[ 0.504000] 8021q: 802.1Q VLAN Support v1.8
[ 0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.524000] Freeing unused kernel memory: 200k freed
[ 3.476000] eth0: link forced UP - 100/full - flow control off/off
[ 3.704000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
[ 4.772000] There is already a switch registered on the device 'eth0'
[ 6.224000] Button Hotplug driver version 0.4.1
[ 13.588000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 13.592000] Backport based on wireless-testing.git master-2012-09-07
[ 13.600000] compat.git: wireless-testing.git
[ 13.668000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.672000] cfg80211: World regulatory domain updated:
[ 13.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.688000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.696000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.704000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.712000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.720000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.304000] SCSI subsystem initialized
[ 14.396000] There is already a switch registered on the device 'eth0'
[ 14.656000] usbcore: registered new interface driver usbfs
[ 14.660000] usbcore: registered new interface driver hub
[ 14.668000] usbcore: registered new device driver usb
[ 15.952000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 15.968000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[ 15.976000] ath: phy0: random mac address will be used: 6e:e6:c6:fe:55:df
[ 15.984000] ath: EEPROM regdomain: 0x0
[ 15.984000] ath: EEPROM indicates default country code should be used
[ 15.984000] ath: doing EEPROM country->regdmn map search
[ 15.984000] ath: country maps to regdmn code: 0x3a
[ 15.984000] ath: Country alpha2 being used: US
[ 15.984000] ath: Regpair used: 0x3a
[ 15.996000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 16.000000] Registered led device: ath9k-phy0
[ 16.000000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc02e0000, irq=39
[ 16.012000] cfg80211: Calling CRDA for country: US
[ 16.016000] cfg80211: Regulatory domain changed to country: US
[ 16.020000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.028000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 16.036000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 16.044000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.052000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.060000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.068000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 17.408000] PPP generic driver version 2.4.2
[ 17.984000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.364000] NET: Registered protocol family 24
[ 18.576000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 18.684000] bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
[ 18.688000] bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
[ 18.724000] bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
[ 18.740000] bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 18.748000] hub 1-0:1.0: USB hub found
[ 18.752000] hub 1-0:1.0: 2 ports detected
[ 18.944000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[ 19.268000] usb 1-1: new high-speed USB device number 2 using bcm63xx_ehci
[ 19.696000] hub 1-1:1.0: USB hub found
[ 19.708000] hub 1-1:1.0: 2 ports detected
[ 19.984000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.092000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 20.096000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
[ 20.104000] bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
[ 20.172000] hub 2-0:1.0: USB hub found
[ 20.176000] hub 2-0:1.0: 2 ports detected
[ 20.352000] uhci_hcd: USB Universal Host Controller Interface driver
[ 20.540000] usbcore: registered new interface driver usblp
[ 20.592000] Initializing USB Mass Storage driver...
[ 20.596000] usbcore: registered new interface driver usb-storage
[ 20.604000] USB Mass Storage support registered.
[ 20.808000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 20.860000] fuse init (API version 7.18)
[ 27.312000] eth0: link forced UP - 100/full - flow control off/off
[ 27.336000] device eth0 entered promiscuous mode
[ 27.348000] br-lan: port 1(eth0) entered forwarding state
[ 27.352000] br-lan: port 1(eth0) entered forwarding state
[ 29.356000] br-lan: port 1(eth0) entered forwarding state
[ 57.124000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 57.132000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 57.140000] jffs2_build_filesystem(): erasing all blocks after the end marker...

(Nota: La opción de compilar la he probado hoy por primera vez en la ofi, que tengo máquina, pero me da error. Y en casa el portátil dijo "hasta la vista babe" y con el AMD K7 va a ser que no puedo hacer muchas pruebas de compliación.)

Gracias y un saludo

jar229 · « **Respuesta #1472 en:** 22-05-2013, 08:02 (Miércoles) »

Como tu router tiene wifi atheros, yo usaría el backport a backfire: http://www.mediafire.com/?0d6x4ozbmvfr59o

Esta compilación incluye: LuCi, FPU emulation, transmission, ftp, servidor de impresión, samba, usb-storage, etc.

Con esta no tendrás problemas para instalar nuevos paquetes dependientes del kernel.

Me resulta raro que no te funciones el backport a attitude adjustment

locobyte · « **Respuesta #1473 en:** 22-05-2013, 13:21 (Miércoles) »

Cita de: dlop en 21-05-2013, 20:55 (Martes)

Hola.

Un problemilla:
Llevo unos dias intentado reinstalar el Openwrt en el HG556a, y siempre me falta algo:
- He probado igual que cuando el kernel er 3.3.8, pero con el firm R36114, con el R35318 y con el trunk... pero los repositorios ya han cambiado a kernel 3.8 y no admite lo de la impresora.
- Y he probado tambien con el firm de attitude adjustment 12.09 y con el trunk... pero ahí el problema es con la wifi, que no aparece.

- ¿Alguna solución, o teneis previsto alguna versión con el kernel actual?

Esta es mi secuencia de instalación ahora
Citar
1.- Descargar imagen nueva
2.- Instalar imagen (interfaz web) "openwrt-HW556-squashfs-cfe_20130521.bin"
3.- Acceder por telnet
4.- Asignar password y modificar ip y gateway, y reiniciar network
5.- Conectar por SSH
6.- Modificar el dns: vi /etc/resolv .. 8.8.8.8
7.- Reiniciar network: /etc/init.d/network restart
8.- opkg install luci (y baja un montón de cosas)
9- /etc/init.d/uhttpd start
10.- /etc/init.d/uhttpd enable
11.- Conectar por web (ha cambiado a tipo "bootstrap")

Te falta instalar los drivers y activar la wifi.
Sigue los pasos que publico el compañero raphik y perfecto.

1) Instalas la imagen squashfs del trunk.
2) Instalas LuCI.
3) Desde LuCI instalas kmod-ath9k si es Atheros o kmod-rt2800-pci si es Ralink.
4) Desde una sesión SSH tecleas: wifi detect > /etc/config/wireless.
5) Otra vez desde LuCI instalas libiwinfo-lua y wpa-supplicant-mini.

locobyte · « **Respuesta #1474 en:** 22-05-2013, 13:28 (Miércoles) »

Cita de: raphik en 15-02-2013, 18:25 (Viernes)

Cita de: ximox en 06-02-2013, 09:25 (Miércoles)
como ya comente anteriormente queria usar un 556a solamente como radio wifi... me dan ganas de coger el router y tirarlo por la ventana para hacer una prueba de resistencia a la altura
Ya tengo la radio wifi funcionando ¡a partir del firmware básico del trunk! ¿Cómo? :
1) Instalas la imagen squashfs del trunk.
2) Instalas LuCI.
3) Desde LuCI instalas kmod-ath9k si es Atheros o kmod-rt2800-pci si es Ralink.
4) Desde una sesión SSH tecleas: wifi detect > /etc/config/wireless.
5) Otra vez desde LuCI instalas libiwinfo-lua y wpa-supplicant-mini.

Y luego sigues las instrucciones para montar la radio en su hilo correspondiente.

Perfecto!!muchas gracias!!

dlop · « **Respuesta #1475 en:** 22-05-2013, 19:01 (Miércoles) »

Genial. Gracias a jar229 y a locobyte.
Al final opté por la solución de locobyte con la trunk, por eso de intentar ir "a la última" (cada x meses)
Jar229: ¿Puedes explicar que es eso de "backport" a backfire? ¿Significa que el repositorio lo mantienen con todos los packetes sin sobre-escribir con versiones de kernels mas nuevos? (Soy de windows, y el Openwrt me ha servido para atreverme con linux)

Como decía: B I E N

por los dos, me habeis permitido avanzar
(
Ahora me estoy peleando con el p910, pero seguiré intentandolo por mi cuenta (leyendo) un par de dias antes de volver a molestar.

Un saludo

zanuksi · « **Respuesta #1476 en:** 22-05-2013, 20:29 (Miércoles) »

Pues e probado de todo y sigo igual solo navego por cable. La compilacion que me pasaste no trae el driver necesario (o por lo menos no me aparece) el 2800usb. ¿Es un fallo mio o deberia aparecerme?

jar229 · « **Respuesta #1477 en:** 22-05-2013, 22:02 (Miércoles) »

Cita de: dlop en 22-05-2013, 19:01 (Miércoles)

Jar229: ¿Puedes explicar que es eso de "backport" a backfire? ¿Significa que el repositorio lo mantienen con todos los packetes sin sobre-escribir con versiones de kernels mas nuevos? (Soy de windows, y el Openwrt me ha servido para atreverme con linux)

Backfire es una de la revisiones estables.
Y sí, si instalas el backport, podrás bajar los paquetes que quieras del repositorio de OpenWrt sin ningún problema de compatibilidad con el kernel.

Cita de: dlop en 22-05-2013, 19:01 (Miércoles)

Ahora me estoy peleando con el p910, pero seguiré intentandolo por mi cuenta (leyendo) un par de dias antes de volver a molestar.

Un saludo

Pues es muy sencillo de configurar. En el hilo del hg553 tienes algo de info al respecto: https://foro.seguridadwireless.net/openwrt/instalacion-(facil)-de-openwrt-en-huawei-553/

Cita de: zanuksi en 22-05-2013, 20:29 (Miércoles)

Pues e probado de todo y sigo igual solo navego por cable. La compilacion que me pasaste no trae el driver necesario (o por lo menos no me aparece) el 2800usb. ¿Es un fallo mio o deberia aparecerme?

Pues según el primer mensaje del hilo si lo incluye

Citar

luci + swconfig + kmod-usb2 + kmod-brcmfmac + kmod-rt2500-usb + kmod-rt2800-usb + kmod-rt73-usb + kmod-rtl8187 + Ralink MAC Patch + ATH_USER_REGD
r35318

zanuksi · « **Respuesta #1478 en:** 23-05-2013, 01:39 (Jueves) »

pues acabo de confirmar en otro router exactamente igual tampoco me aparece, Algun alma caritativa que lo pueda probar =??

jar229 · « **Respuesta #1479 en:** 23-05-2013, 08:13 (Jueves) »

Cita de: zanuksi en 23-05-2013, 01:39 (Jueves)

pues acabo de confirmar en otro router exactamente igual tampoco me aparece, Algun alma caritativa que lo pueda probar =??

Prueba con esta: http://www.mediafire.com/download/mqfawkbh21lqgra/r35162.openwrt-HW556-squashfs-cfe.bin

La tengo funcionando en un router, con wifi ralink, perfectamente.

r35162: Kernel 3.6.11 + FPU emulation + LuCi + kmod-usb2 + kmod-rt73-usb + kmod-rt2800-usb + transmission + p910nd (servidor de impresion) + soporte de sistema de ficheros ext4, ntfs y fat16/32 + samba + pure-ftp (servidor de ftp), wol, etc.+ Ralink MAC Patch + ATH_USER_REGD + sysupgrade

Yo no tengo ninguna usb wifi con ralink 3070, pero como poco, debería funcionarte la wifi interna ...

Noticias:

Autor Tema: [Desarrollo] OpenWrt en Huawei HG556a (Leído 2230096 veces)

masuele

masuele

zanuksi

zanuksi

zanuksi

zanuksi

dlop

locobyte

locobyte

dlop

zanuksi

zanuksi