Gracias jar.

acabo de quitar los dos tornillos y desmontar el router, y he localizado,gracias a tu enlace, el rx y el tx.

¿hago un puente con un clip mismo y sin conectarlo a la corriente o como lo hago? ¿o conectandolo a la corriente pero sin darle al interruptor? Es que este punto no me queda muy claro.

Gracias

Según el primer post de este hilo :

Para instalar OpenWrt:
Desde la web del firmware original o parando el CFE desde una consola serie y luego acceder con un navegador a la dirección 192.168.1.1. En este modelo no se puede cargar el firmware con el procedimiento habitual encendiendo el router con el botón de reset pulsado y manteniéndolo apretado durante 30 segundos.

El puentear RX y TX es para simular que hemos pulsado una tecla y parar el arranque del CFE, así que con el router apagado, pon el clip, dale al encendido, espera unos 5 segundos y quita el clip. Esto hará que piense que hemos pulsado una tecla. Ahora engánchate a la IP 192.168.1.1 y verás la web de rescate. Desde esa web podrás subir la imagen que generes compilando.

Buenas de nuevo.

A ver os cuento:

Cogí el router, desmonté la carcasa, hice puente entre tx y rx con dos alfileres, encendí, esperé cinco segundos quité los alfileres y desconecté de la corriente.

Lo enchufo al pc, el adaptador de red no le meto ningún dato, y meto 192.168.1.1, con admin/admin (no me sale la web de rescate), me sale la info del router:

CFE Bootloader 1.0.37-105.22-1

L411-410JAZ-C05_R02.A2pv6C035b.d23i

Cojo, me voy a backup, y cargo el firmware recién compilado a través de allí,

openwrt-VR-3025un-squashfs-cfe.bin

Se reinicia, y vuelvo a poner la 192.168.1.1, me salta root, y creo una nueva contraseña, y voilá!

Ya tengo la interface de Luci delante de mis ojos.

He hecho la prueba, de apagar y encender el router para ver si se borraba el firmware, y no, ahí sigue, el openwrt en el router.

Un par de detalles:

- La hora del router, no concuerda con la real ¿donde modifico ese parámetro?

Gracias!

Soy así Tki2000

jajajajaj que le vamos a hacer 

De todas formas, aunque no me haya salido la web de rescate por lo que se ve ¿se flasheó bien verdad?

¿alguna prueba adicional para confirmar que se grabó bien el openwrt?

Muchas gracias

Cita de: Raikkok en 27-06-2014, 11:03 (Viernes)

Soy así Tki2000

jajajajaj que le vamos a hacer 

De todas formas, aunque no me haya salido la web de rescate por lo que se ve ¿se flasheó bien verdad?

¿alguna prueba adicional para confirmar que se grabó bien el openwrt?

Muchas gracias

Si no notas nada raro, esque funciona de forma correcta.
De todas formas, podrías postear una salida del comando dmesg.

enviado desde mi Onda v975i

¿el dmesg, viene de serie activado, o lo tienes que incluir de manera manual durante la compilación, jar?

Gracias

Cita de: Raikkok en 27-06-2014, 12:07 (Viernes)

Cita de: jar229 en 27-06-2014, 11:56 (Viernes)

Cita de: Raikkok en 27-06-2014, 11:03 (Viernes)

Soy así Tki2000

jajajajaj que le vamos a hacer  

De todas formas, aunque no me haya salido la web de rescate por lo que se ve ¿se flasheó bien verdad?

¿alguna prueba adicional para confirmar que se grabó bien el openwrt?

Muchas gracias

Si no notas nada raro, esque funciona de forma correcta.
De todas formas, podrías postear una salida del comando dmesg.

enviado desde mi Onda v975i

¿el dmesg, viene de serie activado, o lo tienes que incluir de manera manual durante la compilación, jar?

Gracias

Viene de serie.

Si te resulta más cómodo, con el router recién arrancado, puedes verlo desde LuCi - Estado - Registro del kernel  

Ahora posteo, y edito este mensaje con el log.

Gracias jar


[    0.000000] Linux version 3.10.34 (javi@javi-VirtualBox) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40396) ) #1 Wed Jun 25 14:12:21 CEST 2014
[    0.000000] Detected Broadcom 0x6368 CPU revision b2
[    0.000000] CPU frequency is 400 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 38 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: 96368M-1341N
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802ccab0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:

• 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 61560k/65536k available (2299k kernel code, 3976k reserved, 597k data, 172k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.044000] NET: Registered protocol family 16
[    0.052000] registering PCI controller with io_map_base unset
[    0.060000] bio: create slab <bio-0> at 0
[    0.064000] PCI host bridge to bus 0000:00
[    0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.072000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.076000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.080000] pci 0000:00:01.0: [14e4:432c] type 00 class 0x028000
[    0.080000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff]
[    0.092000] pci 0000:00:01.0: supports D1 D2
[    0.092000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.092000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.092000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
[    0.096000] Switching to clocksource MIPS
[    0.104000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    0.108000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
[    0.132000] ssb: Found chip with id 0x4322, rev 0x01 and package 0x09
[    0.140000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x17, vendor 0x4243)
[    0.140000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
[    0.140000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x0B, vendor 0x4243)
[    0.140000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
[    0.140000] ssb: Core 4 found: USB 2.0 Device (cc 0x81A, rev 0x05, vendor 0x4243)
[    0.140000] ssb: Core 5 found: ARM Cortex M3 (cc 0x82A, rev 0x00, vendor 0x4243)
[    0.140000] ssb: Core 6 found: Internal Memory (cc 0x80E, rev 0x03, vendor 0x4243)
[    0.200000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[    0.208000] NET: Registered protocol family 2
[    0.216000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.220000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.228000] TCP: Hash tables configured (established 512 bind 512)
[    0.236000] TCP: reno registered
[    0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.244000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.252000] NET: Registered protocol family 1
[    0.256000] PCI: CLS 0 bytes, default 16
[    0.260000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.264000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.276000] msgmni has been set to 120
[    0.280000] io scheduler noop registered
[    0.284000] io scheduler deadline registered (default)
[    0.288000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
[    0.296000] console [ttyS0] enabled, bootconsole disabled
[    0.308000] bcm63xx-rng bcm63xx-rng: registered RNG driver
[    0.316000] physmap platform flash device: 08000000 at 18000000
[    0.324000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.332000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    0.332000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.332000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    0.336000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.340000]   Amd/Fujitsu Extended Query version 1.1.
[    0.344000] number of CFI chips: 1
[    0.348000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
[    0.356000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.364000] bcm63xxpart: Partition 1 is kernel offset 10100 and length fff00
[    0.372000] bcm63xxpart: Partition 2 is rootfs offset 110000 and length 6e0000
[    0.376000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[    0.384000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[    0.392000] bcm63xxpart: Spare partition is offset 390004 and length 45fffc
[    0.400000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.408000] Creating 5 MTD partitions on "physmap-flash.0":
[    0.412000] 0x000000000000-0x000000010000 : "CFE"
[    0.420000] 0x000000010100-0x000000110000 : "kernel"
[    0.424000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.440000] 0x000000110000-0x0000007f0000 : "rootfs"
[    0.448000] mtd: device 2 (rootfs) set to be root filesystem
[    0.452000] mtd: partition "rootfs_data" created automatically, ofs=0x390000, len=0x460000
[    0.460000] 0x000000390000-0x0000007f0000 : "rootfs_data"
[    0.468000] 0x0000007f0000-0x000000800000 : "nvram"
[    0.476000] 0x000000010000-0x0000007f0000 : "linux"
[    0.484000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
[    0.528000] b53_common: found switch: BCM63xx, rev 0
[    0.532000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.544000] TCP: cubic registered
[    0.544000] NET: Registered protocol family 17
[    0.552000] 8021q: 802.1Q VLAN Support v1.8
[    0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.572000] Freeing unused kernel memory: 172K (802e5000 - 80310000)
[    3.188000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[    4.440000] usbcore: registered new interface driver usbfs
[    4.448000] usbcore: registered new interface driver hub
[    4.452000] usbcore: registered new device driver usb
[    4.464000] Button Hotplug driver version 0.4.1
[    4.476000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.484000] ehci-platform: EHCI generic platform driver
[    4.592000] ehci-platform ehci-platform: EHCI Host Controller
[    4.596000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.604000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
[    4.624000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    4.632000] hub 1-0:1.0: USB hub found
[    4.636000] hub 1-0:1.0: 1 port detected
[    4.644000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.652000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[    4.660000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    4.668000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
[    4.732000] hub 2-0:1.0: USB hub found
[    4.736000] hub 2-0:1.0: 1 port detected
[    4.744000] uhci_hcd: USB Universal Host Controller Interface driver
[    4.760000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[    6.036000] jffs2: notice: (223) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 0 orphan) found.
[   10.064000] NET: Registered protocol family 10
[   10.112000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[   10.128000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.220000] u32 classifier
[   10.220000]     input device check on
[   10.224000]     Actions configured
[   10.244000] Mirror/redirect action on
[   10.264000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[   10.272000] Backport generated by backports.git backports-20140221-0-g8e94650
[   10.296000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.372000] usbcore: registered new interface driver usbserial
[   10.384000] usbcore: registered new interface driver usbserial_generic
[   10.392000] usbserial: USB Serial support registered for generic
[   10.488000] xt_time: kernel timezone is -0000
[   10.564000] cfg80211: Calling CRDA to update world regulatory domain
[   10.576000] cfg80211: World regulatory domain updated:
[   10.580000] cfg80211:  DFS Master region: unset
[   10.584000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.592000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.604000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.612000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.620000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.628000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.636000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   10.736000] PPP generic driver version 2.4.2
[   10.744000] NET: Registered protocol family 24
[   10.792000] b43-phy0: Broadcom 4322 WLAN found (core revision 16)
[   10.844000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 4
[   10.964000] Broadcom 43xx driver loaded [ Features: PNL ]
[   10.976000] usbcore: registered new interface driver option
[   10.980000] usbserial: USB Serial support registered for GSM modem (1-port)
[   11.008000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.104000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[   20.056000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[   20.068000] device eth0.1 entered promiscuous mode
[   20.072000] device eth0 entered promiscuous mode
[   20.088000] br-lan: port 1(eth0.1) entered forwarding state
[   20.092000] br-lan: port 1(eth0.1) entered forwarding state
[   21.052000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   22.096000] br-lan: port 1(eth0.1) entered forwarding state


¿Todo normal o alguna anomalía?

Gracias jar por la apreciación.

He vuelto a recompilar, incluyendo la opción que me indicabas, y éste es ahora el log de kernel:

[    0.000000] Linux version 3.10.34 (javi@javi-VirtualBox) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40396) ) #2 SMP Sat Jun 28 13:43:17 CEST 2014
[    0.000000] Detected Broadcom 0x6368 CPU revision b2
[    0.000000] CPU frequency is 400 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] registering 38 GPIOs
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: 96368M-1341N
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 80305a00, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6592 r8192 d13888 u32768
[    0.000000] pcpu-alloc: s6592 r8192 d13888 u32768 alloc=8*4096
[    0.000000] pcpu-alloc:

• 0
• 1

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 61268k/65536k available (2476k kernel code, 4268k reserved, 624k data, 224k init, 0k highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.044000] SMP: Booting CPU1...
[    0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[    0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[    0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.080000] Synchronize counters for CPU 1: done.
[    0.080000] SMP: CPU1 is running
[    0.084000] Brought up 2 CPUs
[    0.108000] NET: Registered protocol family 16
[    0.116000] registering PCI controller with io_map_base unset
[    0.128000] bio: create slab <bio-0> at 0
[    0.132000] PCI host bridge to bus 0000:00
[    0.136000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    0.140000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
[    0.144000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.148000] pci 0000:00:01.0: [14e4:432c] type 00 class 0x028000
[    0.148000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff]
[    0.160000] pci 0000:00:01.0: supports D1 D2
[    0.160000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.160000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.160000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
[    0.164000] Switching to clocksource MIPS
[    0.172000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    0.180000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
[    0.200000] ssb: Found chip with id 0x4322, rev 0x01 and package 0x09
[    0.208000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x17, vendor 0x4243)
[    0.208000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
[    0.208000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x0B, vendor 0x4243)
[    0.208000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
[    0.208000] ssb: Core 4 found: USB 2.0 Device (cc 0x81A, rev 0x05, vendor 0x4243)
[    0.208000] ssb: Core 5 found: ARM Cortex M3 (cc 0x82A, rev 0x00, vendor 0x4243)
[    0.208000] ssb: Core 6 found: Internal Memory (cc 0x80E, rev 0x03, vendor 0x4243)
[    0.268000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[    0.276000] NET: Registered protocol family 2
[    0.284000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.292000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
[    0.296000] TCP: Hash tables configured (established 512 bind 512)
[    0.304000] TCP: reno registered
[    0.308000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.312000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.320000] NET: Registered protocol family 1
[    0.324000] PCI: CLS 0 bytes, default 16
[    0.328000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.332000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.344000] msgmni has been set to 119
[    0.348000] io scheduler noop registered
[    0.352000] io scheduler deadline registered (default)
[    0.360000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
[    0.368000] console [ttyS0] enabled, bootconsole disabled
[    0.380000] bcm63xx-rng bcm63xx-rng: registered RNG driver
[    0.388000] physmap platform flash device: 08000000 at 18000000
[    0.396000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.404000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    0.404000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.404000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    0.404000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.412000]   Amd/Fujitsu Extended Query version 1.1.
[    0.416000] number of CFI chips: 1
[    0.420000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
[    0.428000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.436000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
[    0.440000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d0000
[    0.448000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[    0.456000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[    0.464000] bcm63xxpart: Spare partition is offset 3a0004 and length 44fffc
[    0.472000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[    0.476000] Creating 5 MTD partitions on "physmap-flash.0":
[    0.484000] 0x000000000000-0x000000010000 : "CFE"
[    0.492000] 0x000000010100-0x000000120000 : "kernel"
[    0.496000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.512000] 0x000000120000-0x0000007f0000 : "rootfs"
[    0.520000] mtd: device 2 (rootfs) set to be root filesystem
[    0.524000] mtd: partition "rootfs_data" created automatically, ofs=0x3a0000, len=0x450000
[    0.532000] 0x0000003a0000-0x0000007f0000 : "rootfs_data"
[    0.540000] 0x0000007f0000-0x000000800000 : "nvram"
[    0.548000] 0x000000010000-0x0000007f0000 : "linux"
[    0.556000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
[    0.604000] b53_common: found switch: BCM63xx, rev 0
[    0.608000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.620000] TCP: cubic registered
[    0.624000] NET: Registered protocol family 17
[    0.628000] 8021q: 802.1Q VLAN Support v1.8
[    0.640000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.648000] Freeing unused kernel memory: 224K (80318000 - 80350000)
[    3.048000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[    4.060000] usbcore: registered new interface driver usbfs
[    4.064000] usbcore: registered new interface driver hub
[    4.072000] usbcore: registered new device driver usb
[    4.084000] Button Hotplug driver version 0.4.1
[    4.092000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.100000] ehci-platform: EHCI generic platform driver
[    4.208000] ehci-platform ehci-platform: EHCI Host Controller
[    4.212000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.220000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
[    4.240000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    4.248000] hub 1-0:1.0: USB hub found
[    4.252000] hub 1-0:1.0: 1 port detected
[    4.260000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.264000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[    4.272000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    4.280000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
[    4.348000] hub 2-0:1.0: USB hub found
[    4.352000] hub 2-0:1.0: 1 port detected
[    4.360000] uhci_hcd: USB Universal Host Controller Interface driver
[    4.372000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[   10.340000] NET: Registered protocol family 10
[   10.396000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[   10.420000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.508000] u32 classifier
[   10.508000]     input device check on
[   10.512000]     Actions configured
[   10.524000] Mirror/redirect action on
[   10.540000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[   10.548000] Backport generated by backports.git backports-20140221-0-g8e94650
[   10.568000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.660000] usbcore: registered new interface driver usbserial
[   10.664000] usbcore: registered new interface driver usbserial_generic
[   10.672000] usbserial: USB Serial support registered for generic
[   10.732000] xt_time: kernel timezone is -0000
[   10.776000] cfg80211: Calling CRDA to update world regulatory domain
[   10.784000] cfg80211: World regulatory domain updated:
[   10.788000] cfg80211:  DFS Master region: unset
[   10.792000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.804000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.812000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.820000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.828000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.836000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.844000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   10.944000] PPP generic driver version 2.4.2
[   10.952000] NET: Registered protocol family 24
[   11.000000] b43-phy0: Broadcom 4322 WLAN found (core revision 16)
[   11.052000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 4
[   11.084000] Broadcom 43xx driver loaded [ Features: PNL ]
[   11.096000] usbcore: registered new interface driver option
[   11.100000] usbserial: USB Serial support registered for GSM modem (1-port)
[   11.184000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   17.240000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[   21.744000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[   21.760000] device eth0.1 entered promiscuous mode
[   21.764000] device eth0 entered promiscuous mode
[   21.772000] br-lan: port 1(eth0.1) entered forwarding state
[   21.776000] br-lan: port 1(eth0.1) entered forwarding state
[   22.740000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   23.780000] br-lan: port 1(eth0.1) entered forwarding state
[   24.300000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   24.324000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   24.328000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   61.272000] jffs2: notice: (1114) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.


Ahora creo que debería de estar bien

Un saludo, buen finde

Citar

[    0.044000] SMP: Booting CPU1...
[    0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[    0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[    0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.080000] Synchronize counters for CPU 1: done.
[    0.080000] SMP: CPU1 is running
[    0.084000] Brought up 2 CPUs

Ahora sí 

Perfecto! 

Ahora sólo me falta liberar el modem 3g usb

Ya os contaré, un saludete!

Puedes colgar tu compilación o pasarme un link, quiero actualizar el mio a ver que tal va con smp activado

Puedes colgar tu compilación o pasarme un link, quiero actualizar el mio a ver que tal va con smp activado

Yo hace tiempo que colgé una compilación con SMP que funciona perfectamente. Está un par de páginas atrás.

Enviado desde mi CUBOT GT99

Como sugerencia: lee las F.A.Q.

Enviado desde mi CUBOT GT99