Gracias jar por la apreciación.
He vuelto a recompilar, incluyendo la opción que me indicabas, y éste es ahora el log de kernel:
[ 0.000000] Linux version 3.10.34 (javi@javi-VirtualBox) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40396) ) #2 SMP Sat Jun 28 13:43:17 CEST 2014
[ 0.000000] Detected Broadcom 0x6368 CPU revision b2
[ 0.000000] CPU frequency is 400 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 38 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 96368M-1341N
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 80305a00, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6592 r8192 d13888 u32768
[ 0.000000] pcpu-alloc: s6592 r8192 d13888 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 61268k/65536k available (2476k kernel code, 4268k reserved, 624k data, 224k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.044000] SMP: Booting CPU1...
[ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.080000] Synchronize counters for CPU 1: done.
[ 0.080000] SMP: CPU1 is running
[ 0.084000] Brought up 2 CPUs
[ 0.108000] NET: Registered protocol family 16
[ 0.116000] registering PCI controller with io_map_base unset
[ 0.128000] bio: create slab <bio-0> at 0
[ 0.132000] PCI host bridge to bus 0000:00
[ 0.136000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.140000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.144000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.148000] pci 0000:00:01.0: [14e4:432c] type 00 class 0x028000
[ 0.148000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff]
[ 0.160000] pci 0000:00:01.0: supports D1 D2
[ 0.160000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.160000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.160000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff]
[ 0.164000] Switching to clocksource MIPS
[ 0.172000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 0.180000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
[ 0.200000] ssb: Found chip with id 0x4322, rev 0x01 and package 0x09
[ 0.208000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x17, vendor 0x4243)
[ 0.208000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
[ 0.208000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x0B, vendor 0x4243)
[ 0.208000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
[ 0.208000] ssb: Core 4 found: USB 2.0 Device (cc 0x81A, rev 0x05, vendor 0x4243)
[ 0.208000] ssb: Core 5 found: ARM Cortex M3 (cc 0x82A, rev 0x00, vendor 0x4243)
[ 0.208000] ssb: Core 6 found: Internal Memory (cc 0x80E, rev 0x03, vendor 0x4243)
[ 0.268000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.276000] NET: Registered protocol family 2
[ 0.284000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.292000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
[ 0.296000] TCP: Hash tables configured (established 512 bind 512)
[ 0.304000] TCP: reno registered
[ 0.308000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.312000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.320000] NET: Registered protocol family 1
[ 0.324000] PCI: CLS 0 bytes, default 16
[ 0.328000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.332000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.344000] msgmni has been set to 119
[ 0.348000] io scheduler noop registered
[ 0.352000] io scheduler deadline registered (default)
[ 0.360000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
[ 0.368000] console [ttyS0] enabled, bootconsole disabled
[ 0.380000] bcm63xx-rng bcm63xx-rng: registered RNG driver
[ 0.388000] physmap platform flash device: 08000000 at 18000000
[ 0.396000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.404000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[ 0.404000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.404000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[ 0.404000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.412000] Amd/Fujitsu Extended Query version 1.1.
[ 0.416000] number of CFI chips: 1
[ 0.420000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
[ 0.428000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.436000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
[ 0.440000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d0000
[ 0.448000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[ 0.456000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[ 0.464000] bcm63xxpart: Spare partition is offset 3a0004 and length 44fffc
[ 0.472000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.476000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.484000] 0x000000000000-0x000000010000 : "CFE"
[ 0.492000] 0x000000010100-0x000000120000 : "kernel"
[ 0.496000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.512000] 0x000000120000-0x0000007f0000 : "rootfs"
[ 0.520000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.524000] mtd: partition "rootfs_data" created automatically, ofs=0x3a0000, len=0x450000
[ 0.532000] 0x0000003a0000-0x0000007f0000 : "rootfs_data"
[ 0.540000] 0x0000007f0000-0x000000800000 : "nvram"
[ 0.548000] 0x000000010000-0x0000007f0000 : "linux"
[ 0.556000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
[ 0.604000] b53_common: found switch: BCM63xx, rev 0
[ 0.608000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.620000] TCP: cubic registered
[ 0.624000] NET: Registered protocol family 17
[ 0.628000] 8021q: 802.1Q VLAN Support v1.8
[ 0.640000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.648000] Freeing unused kernel memory: 224K (80318000 - 80350000)
[ 3.048000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[ 4.060000] usbcore: registered new interface driver usbfs
[ 4.064000] usbcore: registered new interface driver hub
[ 4.072000] usbcore: registered new device driver usb
[ 4.084000] Button Hotplug driver version 0.4.1
[ 4.092000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.100000] ehci-platform: EHCI generic platform driver
[ 4.208000] ehci-platform ehci-platform: EHCI Host Controller
[ 4.212000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 4.220000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
[ 4.240000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 4.248000] hub 1-0:1.0: USB hub found
[ 4.252000] hub 1-0:1.0: 1 port detected
[ 4.260000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.264000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 4.272000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 4.280000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
[ 4.348000] hub 2-0:1.0: USB hub found
[ 4.352000] hub 2-0:1.0: 1 port detected
[ 4.360000] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.372000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 10.340000] NET: Registered protocol family 10
[ 10.396000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 10.420000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.508000] u32 classifier
[ 10.508000] input device check on
[ 10.512000] Actions configured
[ 10.524000] Mirror/redirect action on
[ 10.540000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 10.548000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 10.568000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.660000] usbcore: registered new interface driver usbserial
[ 10.664000] usbcore: registered new interface driver usbserial_generic
[ 10.672000] usbserial: USB Serial support registered for generic
[ 10.732000] xt_time: kernel timezone is -0000
[ 10.776000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.784000] cfg80211: World regulatory domain updated:
[ 10.788000] cfg80211: DFS Master region: unset
[ 10.792000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.804000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.812000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.820000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.828000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.836000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.844000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.944000] PPP generic driver version 2.4.2
[ 10.952000] NET: Registered protocol family 24
[ 11.000000] b43-phy0: Broadcom 4322 WLAN found (core revision 16)
[ 11.052000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 4
[ 11.084000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 11.096000] usbcore: registered new interface driver option
[ 11.100000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 11.184000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 17.240000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[ 21.744000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-duplex
[ 21.760000] device eth0.1 entered promiscuous mode
[ 21.764000] device eth0 entered promiscuous mode
[ 21.772000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.776000] br-lan: port 1(eth0.1) entered forwarding state
[ 22.740000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 23.780000] br-lan: port 1(eth0.1) entered forwarding state
[ 24.300000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 24.324000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 24.328000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 61.272000] jffs2: notice: (1114) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Ahora creo que debería de estar bien
Un saludo, buen finde
