Bootlog con OpenWRT
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.10.34 (fernando@Dijkstra) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40396) ) #2 Mon Jun 23 21:51:17 ART 2014
[ 0.000000] unknown BCM6328 variant: 0
[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: A4001N-V000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 96328dg2x2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29008k/32768k available (2309k kernel code, 3760k reserved, 607k data, 216k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.288000] registering PCI controller with io_map_base unset
[ 0.300000] bio: create slab <bio-0> at 0
[ 0.304000] PCI host bridge to bus 0000:00
[ 0.308000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[ 0.312000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.316000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.320000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.324000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[ 0.328000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[ 0.332000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.336000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
[ 0.340000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.344000] Switching to clocksource MIPS
[ 0.352000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 0.360000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
[ 0.368000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[ 0.376000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[ 0.384000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[ 0.476000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[ 0.484000] bcm63xx_sprom_bcma: filled sprom for chip id 0xa8d9
[ 0.500000] bcma: bus0: Bus registered
[ 0.504000] NET: Registered protocol family 2
[ 0.512000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.516000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.524000] TCP: Hash tables configured (established 512 bind 512)
[ 0.532000] TCP: reno registered
[ 0.536000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.540000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.548000] NET: Registered protocol family 1
[ 0.556000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.564000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.572000] msgmni has been set to 56
[ 0.576000] io scheduler noop registered
[ 0.580000] io scheduler deadline registered (default)
[ 0.588000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
[ 0.596000] console [ttyS0] enabled, bootconsole disabled
[ 0.596000] console [ttyS0] enabled, bootconsole disabled
[ 0.612000] m25p80 spi1.0: found s25fl064k, expected m25p80
[ 0.620000] m25p80 spi1.0: s25fl064k (8192 Kbytes)
[ 0.624000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328dg2x2
[ 0.632000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.640000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
[ 0.648000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d0000
[ 0.652000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[ 0.660000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[ 0.668000] bcm63xxpart: Spare partition is offset 480004 and length 36fffc
[ 0.676000] 5 bcm63xxpart partitions found on MTD device spi1.0
[ 0.680000] Creating 5 MTD partitions on "spi1.0":
[ 0.688000] 0x000000000000-0x000000010000 : "CFE"
[ 0.696000] 0x000000010100-0x000000120000 : "kernel"
[ 0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.716000] 0x000000120000-0x0000007f0000 : "rootfs"
[ 0.724000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.728000] mtd: partition "rootfs_data" created automatically, ofs=0x480000, len=0x370000
[ 0.736000] 0x000000480000-0x0000007f0000 : "rootfs_data"
[ 0.744000] 0x0000007f0000-0x000000800000 : "nvram"
[ 0.752000] 0x000000010000-0x0000007f0000 : "linux"
[ 0.800000] b53_common: found switch: BCM63xx, rev 0
[ 0.804000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.816000] TCP: cubic registered
[ 0.820000] NET: Registered protocol family 17
[ 0.824000] 8021q: 802.1Q VLAN Support v1.8
[ 0.840000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.852000] Freeing unused kernel memory: 216K (802ea000 - 80320000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
[ 5.544000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.284000] usbcore: registered new interface driver usbfs
[ 7.288000] usbcore: registered new interface driver hub
[ 7.296000] usbcore: registered new device driver usb
[ 7.316000] Button Hotplug driver version 0.4.1
[ 7.420000] SCSI subsystem initialized
[ 7.440000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.448000] ehci-platform: EHCI generic platform driver
[ 7.560000] ehci-platform ehci-platform: EHCI Host Controller
[ 7.564000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 7.572000] ehci-platform ehci-platform: irq 50, io mem 0xb0002500
[ 7.592000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 7.600000] hub 1-0:1.0: USB hub found
[ 7.604000] hub 1-0:1.0: 1 port detected
[ 7.616000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.620000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 7.628000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 7.636000] ohci-platform ohci-platform: irq 49, io mem 0xb0002600
[ 7.704000] hub 2-0:1.0: USB hub found
[ 7.708000] hub 2-0:1.0: 1 port detected
[ 7.728000] usbcore: registered new interface driver usb-storage
[ 7.736000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 14.196000] NET: Registered protocol family 10
[ 14.236000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 14.272000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 14.292000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.336000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 14.344000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 14.360000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.408000] usbcore: registered new interface driver usblp
[ 14.452000] xt_time: kernel timezone is -0000
[ 14.528000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.540000] cfg80211: World regulatory domain updated:
[ 14.544000] cfg80211: DFS Master region: unset
[ 14.548000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 14.556000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.568000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.576000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.584000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.592000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.600000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 14.712000] PPP generic driver version 2.4.2
[ 14.724000] NET: Registered protocol family 24
[ 14.840000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31
[ 22.136000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 31.188000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 31.200000] device eth0.1 entered promiscuous mode
[ 31.204000] device eth0 entered promiscuous mode
[ 31.220000] br-lan: port 1(eth0.1) entered forwarding state
[ 31.224000] br-lan: port 1(eth0.1) entered forwarding state
[ 32.216000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 33.228000] br-lan: port 1(eth0.1) entered forwarding state
[ 37.992000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 38.008000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 38.012000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 46.464000] jffs2: notice: (920) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
procd: - init complete -