Joder si que desaparece rapido el menu de inicio hasta aqui llego pero no consigo que se trague el firmware.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 1
0
## Powering up port 0 ~ 4.
1: System Load Linux to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (5.75.59.250) ==:192.168.1.10
Input Linux Kernel filename (1.bin) ==:1.bin
netboot_common, argc= 3
KSEG1ADDR(NetTxPacket) = 0xA1FE7800
NetLoop,call eth_halt !
NetLoop,call eth_init !
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename '1.bin'.
TIMEOUT_COUNT=10,Load address: 0x80500000
Loading: Got ARP REPLY, set server/gtwy eth addr (00:1d:7d:e6:d6:9a)
Got it
#
first block received
done
NetBootFileXferSize= 00000000
1.0.0 U-Boot 1.1.3 (Mar 16 2011 - 18:01:52) - SVN revision : 15534
Model: ASL-26564/ES
Board: Ralink APSoC DRAM: 32 MB
config usb..
Command "mdio": 0x8020aeb0 => 0x81fb6eb0
Command "cp": 0x8020c758 => 0x81fb8758
Command "erase": 0x8020c8a8 => 0x81fb88a8
Command "go": 0x8020dc70 => 0x81fb9c70
Command "reset": 0x8021c080 => 0x81fc8080
Command "bootm": 0x8020e4e4 => 0x81fba4e4
Command "tftpboot": 0x8020fdd0 => 0x81fbbdd0
Command "printenv": 0x80210390 => 0x81fbc390
Command "setenv": 0x80210f88 => 0x81fbcf88
Command "saveenv": 0x802110f8 => 0x81fbd0f8
Command "version": 0x80211220 => 0x81fbd220
Command "help": 0x8021126c => 0x81fbd26c
Command "?": 0x8021126c => 0x81fbd26c
Command "httpsvr": 0x80215630 => 0x81fc1630
Command "md": 0x80215b50 => 0x81fc1b50
Command "mm": 0x80215e88 => 0x81fc1e88
Command "nm": 0x80215ee0 => 0x81fc1ee0
Command "mw": 0x80215f38 => 0x81fc1f38
spi_wait_nsec: 5f
spi device id: 1 20 18 3 1 (20180301)
find flash: Sfl128p
============================================
Ralink UBoot Version: 3.3 Alpha
--------------------------------------------
ASIC 3052_MP2 (Port5<->RvMII)
DRAM component: 128 Mbits SDR
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: SPI Flash
Date:Mar 16 2011 Time:18:01:52
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
## Powering down port 0 ~ 4.
y una ves llegado hasta aqui se reinicia el tftpd64 lo tengo como cliente
server interface 192.168.1.10
host 192.168.1.1 port no tengo puesto
el archivo renombrado a 1.bin
tamaño de bloques por defecto
y le doy a put.
estoy usando el firmware que le mandasteis a me109zito este firm permite la opcion uno o directamente a la 2
Muchas gracias por adelantado
¿si no me equivoco ya estoy cerca de conseguirlo?
