Autor Tema: [Desarrollo] OpenWrt en Telefónica Home Station ADB P.DG A4001N1 (Leído 368772 veces)

seny · « **Respuesta #620 en:** 17-10-2014, 23:16 (Viernes) »

Hola, pongo un poco en antecedentes, le cargué a un A4001N la compilación que hay en el repositrio Barrier Breaker 14.07 para el A4001N. quedó el router bloquedado en el arranque y sin respuesta para acceder ni a prueba de fallos.

He soldado los 3 postes a la placa para poder conectar el puerto serie, leo el arranque pero no actua el pulsar una tecla para entrar al CFE y sigue arrancado hasta que se bloquea, creo que si no logro interrumpir el arranque para que entre en el CFE no tengo nada que hacer, ¿estoy en lo cierto?, aqui pego el arranque:

Citar

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN

CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
Copyright (C) 2000-2009 Broadcom Corporation.

HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000

Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-4) : 963281T_TEF
Number of MAC Addresses (1-32) : 11
Base MAC Address : xx:xx:xx:xx:xx:xx:xx
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 1
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xb8800000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/L
inaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 15:07:11 CEST 2014
[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: A4001N-V000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board: board name: 963281T_TEF
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jff
s2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28656k/32768k available (2485k kernel code, 4112k reserve
d, 725k data, 308k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.288000] registering PCI controller with io_map_base unset
[ 0.304000] bio: create slab <bio-0> at 0
[ 0.312000] PCI host bridge to bus 0000:00
[ 0.316000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [ 0x00000000 flags 0x0]
[ 0.324000] pci_bus 0000:00: No busn resource found for root bus, will use [b
us 00-ff]
[ 0.328000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), rec
onfiguring
[ 0.332000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[ 0.336000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bi
t]
[ 0.340000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.344000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
[ 0.348000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.352000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.368000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.376000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.380000] TCP: Hash tables configured (established 512 bind 512)
[ 0.388000] TCP: reno registered
[ 0.392000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.396000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.404000] NET: Registered protocol family 1
[ 0.412000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[ 0.428000] msgmni has been set to 55
[ 0.436000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.444000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_
uart
[ 0.452000] console [ttyS0] enabled, bootconsole disabled
[ 0.452000] console [ttyS0] enabled, bootconsole disabled
[ 0.472000] m25p80 spi1.0: found mx25l12805d, expected m25p80
[ 0.480000] m25p80 spi1.0: mx25l12805d (16384 Kbytes)
[ 0.484000] bcm63xxpart: CFE boot tag found with version 6 and board type 963
281T_TEF
[ 0.492000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.500000] bcm63xxpart: Partition 1 is rootfs offset 10100 and length 57b000

[ 0.508000] bcm63xxpart: Partition 2 is kernel offset 58b100 and length 105a0
f
[ 0.512000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[ 0.520000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[ 0.528000] bcm63xxpart: Spare partition is offset 6a0000 and length 950000
[ 0.536000] 5 bcm63xxpart partitions found on MTD device spi1.0
[ 0.540000] Creating 5 MTD partitions on "spi1.0":
[ 0.548000] 0x000000000000-0x000000010000 : "CFE"
[ 0.556000] 0x000000010100-0x00000058b100 : "rootfs"
[ 0.560000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.576000] mtd: device 1 (rootfs) set to be root filesystem
[ 0.580000] mtdsplit: no squashfs found in "spi1.0"
[ 0.588000] 0x00000058b100-0x000000690b0f : "kernel"
[ 0.592000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.608000] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.616000] 0x000000010000-0x000000ff0000 : "linux"
[ 0.664000] b53_common: found switch: BCM63xx, rev 0
[ 0.672000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.684000] TCP: cubic registered
[ 0.688000] NET: Registered protocol family 17
[ 0.692000] Bridge firewalling registered
[ 0.696000] 8021q: 802.1Q VLAN Support v1.8
[ 0.708000] jffs2: Flash size not aligned to erasesize, reducing to 1024KiB
[ 0.716000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000000: 0x8001 instead
[ 0.724000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000004: 0x8001 instead
[ 0.736000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000008: 0x0010 instead
[ 0.744000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0000000c: 0x6d00 instead
[ 0.752000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000010: 0x0018 instead
[ 0.764000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0000001c: 0xfdff instead
[ 0.772000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000020: 0xb77f instead
[ 0.784000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000024: 0x0b37 instead
[ 0.792000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00000028: 0x50c1 instead
[ 0.804000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0000002c: 0x44a5 instead
[ 0.812000] jffs2: Further such events for this erase block will not be print
ed
[ 0.852000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010000: 0xded9 instead
[ 0.860000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010004: 0x00ad instead
[ 0.872000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010008: 0x6222 instead
[ 0.880000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0001000c: 0x275f instead
[ 0.892000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010010: 0xcebb instead
[ 0.900000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010014: 0xa0d7 instead
[ 0.912000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010018: 0x75c5 instead
[ 0.920000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0001001c: 0x53eb instead
[ 0.932000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010020: 0x500e instead
[ 0.940000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00010024: 0x3f71 instead
[ 0.948000] jffs2: Further such events for this erase block will not be print
ed
[ 0.988000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020000: 0xdc1a instead
[ 1.000000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020004: 0xf491 instead
[ 1.008000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020008: 0x5be4 instead
[ 1.020000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0002000c: 0xe5be instead
[ 1.028000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020010: 0x0f90 instead
[ 1.040000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020014: 0x1a4f instead
[ 1.048000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020018: 0xa1dd instead
[ 1.056000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0002001c: 0xdb5b instead
[ 1.068000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020020: 0xc14b instead
[ 1.076000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00020024: 0xa11f instead
[ 1.088000] jffs2: Further such events for this erase block will not be print
ed
[ 1.128000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030000: 0x7ed8 instead
[ 1.136000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030004: 0x774b instead
[ 1.148000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030008: 0x6375 instead
[ 1.156000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0003000c: 0xf5e7 instead
[ 1.168000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030010: 0xf8c9 instead
[ 1.176000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030014: 0x3abe instead
[ 1.184000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030018: 0xc6a8 instead
[ 1.196000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0003001c: 0x270c instead
[ 1.204000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030020: 0xf098 instead
[ 1.216000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00030024: 0x8c8e instead
[ 1.224000] jffs2: Further such events for this erase block will not be print
ed
[ 1.236000] jffs2: Old JFFS2 bitmask found at 0x00030dd0
[ 1.240000] jffs2: You cannot use older JFFS2 filesystems with newer kernels
[ 1.268000] jffs2: Old JFFS2 bitmask found at 0x0003a58c
[ 1.272000] jffs2: You cannot use older JFFS2 filesystems with newer kernels
[ 1.292000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040000: 0xa775 instead
[ 1.300000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040004: 0x1014 instead
[ 1.308000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040008: 0x3049 instead
[ 1.320000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0004000c: 0xece7 instead
[ 1.328000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040010: 0xefff instead
[ 1.340000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040014: 0x978a instead
[ 1.348000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040018: 0xf5f7 instead
[ 1.360000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0004001c: 0xd926 instead
[ 1.368000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040020: 0x325c instead
[ 1.376000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00040024: 0x4a39 instead
[ 1.388000] jffs2: Further such events for this erase block will not be print
ed
[ 1.428000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050000: 0x3f44 instead
[ 1.436000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050004: 0x775b instead
[ 1.448000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050008: 0x6cf5 instead
[ 1.456000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0005000c: 0x0469 instead
[ 1.468000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050010: 0x996a instead
[ 1.476000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050014: 0xc992 instead
[ 1.488000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050018: 0xcabb instead
[ 1.496000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0005001c: 0xbe51 instead
[ 1.504000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050020: 0x67b8 instead
[ 1.516000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00050024: 0xb890 instead
[ 1.524000] jffs2: Further such events for this erase block will not be print
ed
[ 1.564000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060000: 0x5ec7 instead
[ 1.576000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060004: 0xbef2 instead
[ 1.584000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060008: 0xb7a4 instead
[ 1.596000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0006000c: 0xc1a5 instead
[ 1.604000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060010: 0x01a8 instead
[ 1.612000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060014: 0x2138 instead
[ 1.624000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060018: 0x6649 instead
[ 1.632000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0006001c: 0x4db4 instead
[ 1.644000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060020: 0xdda1 instead
[ 1.652000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00060024: 0x2afa instead
[ 1.664000] jffs2: Further such events for this erase block will not be print
ed
[ 1.704000] jffs2: Old JFFS2 bitmask found at 0x0006ff60
[ 1.708000] jffs2: You cannot use older JFFS2 filesystems with newer kernels
[ 1.716000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070000: 0x165a instead
[ 1.724000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070004: 0xb49f instead
[ 1.736000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070008: 0x8566 instead
[ 1.744000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0007000c: 0x1c4a instead
[ 1.756000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070010: 0xfa0b instead
[ 1.764000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070014: 0x24e5 instead
[ 1.776000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070018: 0x5870 instead
[ 1.784000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0007001c: 0x5685 instead
[ 1.792000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070020: 0xc652 instead
[ 1.804000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00070024: 0xb24f instead
[ 1.812000] jffs2: Further such events for this erase block will not be print
ed
[ 1.852000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080000: 0x3b6b instead
[ 1.864000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080004: 0x0309 instead
[ 1.872000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080008: 0xd512 instead
[ 1.884000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0008000c: 0xb3fb instead
[ 1.892000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080010: 0x6446 instead
[ 1.900000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080014: 0x6794 instead
[ 1.912000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080018: 0x4812 instead
[ 1.920000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0008001c: 0x5b56 instead
[ 1.932000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080020: 0xd35f instead
[ 1.940000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00080024: 0xb28e instead
[ 1.952000] jffs2: Further such events for this erase block will not be print
ed
[ 1.992000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090000: 0x1e0f instead
[ 2.000000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090004: 0xc94e instead
[ 2.012000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090008: 0x021f instead
[ 2.020000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0009000c: 0xdc6c instead
[ 2.028000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090010: 0x7dba instead
[ 2.040000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090014: 0xe038 instead
[ 2.048000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090018: 0x507b instead
[ 2.060000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x0009001c: 0x9941 instead
[ 2.068000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090020: 0x7f44 instead
[ 2.080000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x00090024: 0x2645 instead
[ 2.088000] jffs2: Further such events for this erase block will not be print
ed
[ 2.128000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0000: 0x6904 instead
[ 2.140000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0004: 0x4a7b instead
[ 2.148000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0008: 0xbf83 instead
[ 2.156000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a000c: 0x5d3a instead
[ 2.168000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0010: 0xfc2c instead
[ 2.176000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0014: 0x1b1d instead
[ 2.188000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0018: 0x3598 instead
[ 2.196000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a001c: 0xafa6 instead
[ 2.208000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0020: 0xe99c instead
[ 2.216000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000a0024: 0x583a instead
[ 2.228000] jffs2: Further such events for this erase block will not be print
ed
[ 2.264000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0000: 0xa184 instead
[ 2.276000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0004: 0x3234 instead
[ 2.284000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0008: 0xbb5c instead
[ 2.296000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b000c: 0x97e7 instead
[ 2.304000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0010: 0xb95d instead
[ 2.316000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0014: 0x5b23 instead
[ 2.324000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0018: 0xdc12 instead
[ 2.336000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b001c: 0x4127 instead
[ 2.344000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0020: 0x2cf6 instead
[ 2.352000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000b0024: 0xf4ae instead
[ 2.364000] jffs2: Further such events for this erase block will not be print
ed
[ 2.404000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0000: 0x1518 instead
[ 2.412000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0004: 0x69c8 instead
[ 2.424000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0008: 0xb205 instead
[ 2.432000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c000c: 0xec8e instead
[ 2.444000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0010: 0xafe8 instead
[ 2.452000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0014: 0x425f instead
[ 2.464000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0018: 0xf659 instead
[ 2.472000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c001c: 0x0385 instead
[ 2.480000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0020: 0xa086 instead
[ 2.492000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000c0024: 0x8324 instead
[ 2.500000] jffs2: Further such events for this erase block will not be print
ed
[ 2.540000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0000: 0x0921 instead
[ 2.552000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0004: 0x38c1 instead
[ 2.560000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0008: 0xbdc2 instead
[ 2.572000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d000c: 0xc354 instead
[ 2.580000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0010: 0x4e06 instead
[ 2.588000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0014: 0xbab7 instead
[ 2.600000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0018: 0x8123 instead
[ 2.608000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d001c: 0xb125 instead
[ 2.620000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0020: 0x1805 instead
[ 2.628000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000d0024: 0x62f7 instead
[ 2.640000] jffs2: Further such events for this erase block will not be print
ed
[ 2.680000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0000: 0x44ed instead
[ 2.688000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0004: 0x319a instead
[ 2.700000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0008: 0x9a11 instead
[ 2.708000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e000c: 0xae66 instead
[ 2.716000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0010: 0x7836 instead
[ 2.728000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0014: 0x3409 instead
[ 2.736000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0018: 0x4503 instead
[ 2.748000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e001c: 0x7785 instead
[ 2.756000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0020: 0x3764 instead
[ 2.768000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000e0024: 0xad5f instead
[ 2.776000] jffs2: Further such events for this erase block will not be print
ed
[ 2.816000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0000: 0xf205 instead
[ 2.824000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0004: 0xf891 instead
[ 2.836000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0008: 0xab40 instead
[ 2.844000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f000c: 0xbc05 instead
[ 2.856000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0010: 0xc016 instead
[ 2.864000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0014: 0x10cd instead
[ 2.876000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0018: 0x5737 instead
[ 2.884000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f001c: 0x8dbb instead
[ 2.896000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0020: 0x27e9 instead
[ 2.904000] jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at
0x000f0024: 0x17c8 instead
[ 2.912000] jffs2: Further such events for this erase block will not be print
ed
[ 2.952000] jffs2: Cowardly refusing to erase blocks on filesystem with no va
lid JFFS2 nodes
[ 2.960000] jffs2: empty_blocks 0, bad_blocks 0, c->nr_blocks 16
[ 2.968000] VFS: Cannot open root device "mtdblock2" or unknown-block(31,2):
error -5
[ 2.976000] Please append a correct "root=" boot option; here are the availab
le partitions:
[ 2.984000] 1f00 64 mtdblock0 (driver?)
[ 2.992000] 1f01 5612 mtdblock1 (driver?)
[ 2.996000] 1f02 1046 mtdblock2 (driver?)
[ 3.000000] 1f03 64 mtdblock3 (driver?)
[ 3.004000] 1f04 16256 mtdblock4 (driver?)
[ 3.012000] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(31,2)

Tki2000 · « **Respuesta #621 en:** 18-10-2014, 13:49 (Sábado) »

Cita de: seny en 17-10-2014, 23:16 (Viernes)

Hola, pongo un poco en antecedentes, le cargué a un A4001N la compilación que hay en el repositrio Barrier Breaker 14.07 para el A4001N. quedó el router bloquedado en el arranque y sin respuesta para acceder ni a prueba de fallos.

He soldado los 3 postes a la placa para poder conectar el puerto serie, leo el arranque pero no actua el pulsar una tecla para entrar al CFE y sigue arrancado hasta que se bloquea, creo que si no logro interrumpir el arranque para que entre en el CFE no tengo nada que hacer, ¿estoy en lo cierto?, aqui pego el arranque:

Tiene mala pinta.
Cuando probaba los firmwares con el VH4032N a veces me pasaba esto y unas veces se arreglaba solo tras 4 o 5 arranques y otras veces no había más remedio que flashear otra vez.
Creo que vas a tener que interrumpir el arranque del CFE y flashear mediante TFTP...
Intenta pulsar alguna tecla repetidamente incluso antes de arrancar el router. Hay que ser muy rápido para interrumpir el CFE, ya que pone que sólo te da un segundo...

seny · « **Respuesta #622 en:** 19-10-2014, 22:16 (Domingo) »

Gracias por aclararme el concepto, se interrumpe el CFE no se entra..

Pero no hay forma de interrumpir el arranque, incluso he repasado las soldaduras por si acaso.

Sera cuestion de liarse con otro cacharro y dejar este aparcado, saludos.

faio86 · « **Respuesta #623 en:** 28-10-2014, 16:11 (Martes) »

Buenas, les dejo la manera de instalar luci, si solo podéis acceder por consola

Para editar network y tener acceso a internet

Código: [Seleccionar]

vi /etc/config/network
Una vez que estamos dentro del router y este está conectado a internet tendremos que actualizar los paquetes:

Código: [Seleccionar]

opkg updateLuego instalaremos LuCI sin HTTPS:

Código: [Seleccionar]

opkg install luciy entonces iniciamos y ponerlo al inicio

Código: [Seleccionar]

/etc/init.d/uhttpd enable
/etc/init.d/uhttpd start

Saludos.

correcaminos_iv · « **Respuesta #624 en:** 30-11-2014, 15:27 (Domingo) »

Hola Idollar, tengo el mismo problema que tenías con kmod-tun. Llevo una buena lista de paginas buscando paquetes diferentes y llegué a la conclusión de que tiene que ser un error de instalación en el modulo. Tu recopilación me llenó de esperanzas :-). No soy muy experto en compilarciones y no estoy muy preparado para ello. Sospecho que el mismo módulo que has compilado es el que me vale a mi.
uname -a
Linux homehost 3.10.26 #1 Thu Jan 16 12:01:13 CET 2014 mips GNU/Linux

Es un huawei 556 y sospecho que el tuyo también. Si es así, puedo pedirte que me hagas llegar el módulo que compilaste tu?

Gracias por adelantado.

rullado · « **Respuesta #625 en:** 05-12-2014, 10:51 (Viernes) »

¿Alguien podria explicar cuales cambios fueron hechas para que la puerta usb sea correctamente reconocida?

En este link
https://foro.seguridadwireless.net/openwrt/openwrt-en-routers-de-telefonica-home-station-alpha-asl26555-y-adb-p-dg-a4001n1/msg306965/#msg306965
encontré los cambios para la wifi BCM43225 pero no hay informaciones sobre la usb.

Gracias

limdnas · « **Respuesta #626 en:** 18-12-2014, 19:24 (Jueves) »

se puede poner trasmision a este router y descargar en un disco duro conectado en el usb de este router?

pikomule · « **Respuesta #627 en:** 18-12-2014, 19:36 (Jueves) »

zorrua · « **Respuesta #628 en:** 26-12-2014, 21:59 (Viernes) »

Soporta wifi N?

Muchas gracias.

chinales77 · « **Respuesta #629 en:** 11-01-2015, 12:56 (Domingo) »

Cita de: limdnas en 18-12-2014, 19:24 (Jueves)

se puede poner trasmision a este router y descargar en un disco duro conectado en el usb de este router?

Hola, esto a mi también me interesa.
Meto el pendrive en el USB del router, y ahora como hago para entrar a los datos del USB desde el pc o el móvil?
Salu2 y gracias

jar229 · « **Respuesta #630 en:** 12-01-2015, 09:00 (Lunes) »

Cita de: chinales77 en 11-01-2015, 12:56 (Domingo)

Cita de: limdnas en 18-12-2014, 19:24 (Jueves)
se puede poner trasmision a este router y descargar en un disco duro conectado en el usb de este router?
Hola, esto a mi también me interesa.
Meto el pendrive en el USB del router, y ahora como hago para entrar a los datos del USB desde el pc o el móvil?
Salu2 y gracias

Puedes acceder mediante ftp o samba.

Mira los hilos fijos, que lo tienes todo explicado

pikomule · « **Respuesta #631 en:** 13-01-2015, 14:55 (Martes) »

he instalado este firm del primer mensaje y no tiene luci, es normal?

http://downloads.openwrt.org/barrier_breaker/14.07-rc2/brcm63xx/generic/openwrt-A4001N1-squashfs-cfe.bin

ping hace sin problema

jar229 · « **Respuesta #632 en:** 14-01-2015, 09:35 (Miércoles) »

Cita de: pikomule en 13-01-2015, 14:55 (Martes)

he instalado este firm del primer mensaje y no tiene luci, es normal?

http://downloads.openwrt.org/barrier_breaker/14.07-rc2/brcm63xx/generic/openwrt-A4001N1-squashfs-cfe.bin

ping hace sin problema

Si esa es la URL de la descarga, debería tener LuCi (no es la rama de desarrollo) ...

pikomule · « **Respuesta #633 en:** 14-01-2015, 10:30 (Miércoles) »

no tiene luci. Instale la rc3 de noltari y sin problema. Gracias

eliasgv · « **Respuesta #634 en:** 18-01-2015, 22:41 (Domingo) »

buenas.
yo he compilado siguiendo el tutorial de este enlace https://foro.seguridadwireless.net/openwrt/compilar-openwrt-a-nuestro-gusto/msg253589/#msg253589
Unicamente he cambiado lo siguiente, logicamente para adaptarlo a nuestro router. <Target System> broadcom BCM63xx, <Target Profile> BCM6328, y te selecciona automaticamente A4001N.

me ha conectado con otro router por wifi, pero al intentar crear otra red wifi para que sirva como repetidor

se pierde la conexion.
Estoy de pruebas pero si os interesa esta compilacion con LUCI en español os la puedo facilitar.
Una nota para jar229

por soportarme. probare si puedo ayudar en este post y en el de como compilar si alguien me hecha una mano pues

eliasgv · « **Respuesta #635 en:** 19-01-2015, 00:59 (Lunes) »

Cita de: eliasgv en 18-01-2015, 22:41 (Domingo)

buenas.
yo he compilado siguiendo el tutorial de este enlace https://foro.seguridadwireless.net/openwrt/compilar-openwrt-a-nuestro-gusto/msg253589/#msg253589
Unicamente he cambiado lo siguiente, logicamente para adaptarlo a nuestro router. <Target System> broadcom BCM63xx, <Target Profile> BCM6328, y te selecciona automaticamente A4001N.
me ha conectado con otro router por wifi, pero al intentar crear otra red wifi para que sirva como repetidor se pierde la conexion.
Estoy de pruebas pero si os interesa esta compilacion con LUCI en español os la puedo facilitar.
Una nota para jar229 por soportarme. probare si puedo ayudar en este post y en el de como compilar si alguien me hecha una mano pues

corrijo <Subtarget> brcm6328, <Target Profile> ADB P.DG A4001N

Tki2000 · « **Respuesta #636 en:** 19-01-2015, 06:18 (Lunes) »

Cita de: eliasgv en 18-01-2015, 22:41 (Domingo)

me ha conectado con otro router por wifi, pero al intentar crear otra red wifi para que sirva como repetidor se pierde la conexion.

No vas a conseguir ponerlo en modo repetidor con sólo una wifi. La wifi es Broadcom y no lo soporta. Para hacer de repetidor necesitas otro pincho wifi en el USB para repetir la señal.

eliasgv · « **Respuesta #637 en:** 19-01-2015, 10:42 (Lunes) »

Cita de: Tki2000 en 19-01-2015, 06:18 (Lunes)

Cita de: eliasgv en 18-01-2015, 22:41 (Domingo)
me ha conectado con otro router por wifi, pero al intentar crear otra red wifi para que sirva como repetidor se pierde la conexion.

No vas a conseguir ponerlo en modo repetidor con sólo una wifi. La wifi es Broadcom y no lo soporta. Para hacer de repetidor necesitas otro pincho wifi en el USB para repetir la señal.

Esto es seguro?.
Con el router que daba telefonica antes que este, el Amper ASL-26555, si lo he conseguido.

Tki2000 · « **Respuesta #638 en:** 19-01-2015, 12:18 (Lunes) »

Cita de: eliasgv en 19-01-2015, 10:42 (Lunes)

Cita de: Tki2000 en 19-01-2015, 06:18 (Lunes)
Cita de: eliasgv en 18-01-2015, 22:41 (Domingo)
me ha conectado con otro router por wifi, pero al intentar crear otra red wifi para que sirva como repetidor se pierde la conexion.

No vas a conseguir ponerlo en modo repetidor con sólo una wifi. La wifi es Broadcom y no lo soporta. Para hacer de repetidor necesitas otro pincho wifi en el USB para repetir la señal.

Esto es seguro?.
Con el router que daba telefonica antes que este, el Amper ASL-26555, si lo he conseguido.

El ADB tiene Wifi Broadcom: http://wiki.openwrt.org/toh/adb/p.dg_a4001n1
El Amper tiene Wifi Ralink: http://wiki.openwrt.org/toh/alpha/asl26555
SI, es seguro... Aparte de que son blancos y aplastados, no tienen nada en común por dentro...

eliasgv · « **Respuesta #639 en:** 19-01-2015, 15:47 (Lunes) »

Cita de: Tki2000 en 19-01-2015, 12:18 (Lunes)

El ADB tiene Wifi Broadcom: http://wiki.openwrt.org/toh/adb/p.dg_a4001n1
El Amper tiene Wifi Ralink: http://wiki.openwrt.org/toh/alpha/asl26555
SI, es seguro... Aparte de que son blancos y aplastados, no tienen nada en común por dentro...

Re: WDS con 2 Home Station ADB P.DG A4001N
el ‎19-09-2012 15:33
Buenas tardes Castillo92:

Persona de nuestro laboratorio de Tecnología ha realizado pruebas en el laboratorio conectando dos BHS de ADB mediante este procedimiento.

Para ello han configurado en los dos routers una misma SSID, mismo canal y misma seguridad de la WLAN. El primer router mantiene su dirección LAN 192.168.1.1 y el DHCP habilitado, mientras que al otro router le asignamos la dirección LAN 192.168.1.2 y le deshabilitamos el DHCP (El primer router le asignará dirección).

Segun estos lo han conseguido en modo WDS, pienso entonces se podria conseguir sin tener que toquetear el router emisor

saludos

Noticias:

Autor Tema: [Desarrollo] OpenWrt en Telefónica Home Station ADB P.DG A4001N1 (Leído 368772 veces)

seny

seny

faio86

correcaminos_iv

rullado

limdnas

pikomule

zorrua

chinales77

pikomule

pikomule

eliasgv

eliasgv

eliasgv

eliasgv