?>/script>'; } ?> TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!! Widgets Magazine

Autor Tema: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!  (Leído 112915 veces)

0 Usuarios y 1 Visitante están viendo este tema.

SERASER

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #80 en: 27-02-2012, 23:33 (Lunes) »
¿Que baudrate le tienes?

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #81 en: 27-02-2012, 23:35 (Lunes) »
115200

5.1

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #82 en: 27-02-2012, 23:35 (Lunes) »
A ver, en el putty  lo tienes bien, a 115200, pero el puerto COM1 lo has configurado a esa velocidad en el administrador de dispositivos?

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #83 en: 27-02-2012, 23:40 (Lunes) »
bits por segundo 115200
bits de datos                  8
pariedad              ninguno
bits parada                     1
control de flujo     ninguno

SERASER

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #84 en: 27-02-2012, 23:43 (Lunes) »
Esta bien, es el cable, no hay mas....

5.1

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #85 en: 27-02-2012, 23:44 (Lunes) »
Pues eso tambien lo tienes correctamente configurado, así que una de dos, o te has equivocado con los RX,TX,GND o el circuito que tienes montado no acaba de ser correcto, la buena noticia como dice sERASEr es que no has perdido el bootloader... o eso creo

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #86 en: 27-02-2012, 23:45 (Lunes) »
voy a mirar por que no me fio mucho del punto gnd si hay alguno alternativo

5.1

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #87 en: 27-02-2012, 23:48 (Lunes) »
Animo, que solo llevamos 5 paginas para conseguirlo  ;D

PD : Asegurate que las conexiones al puerto serie del router estan bien hechas, no sea que haya cambiado Rx por TX o algo de eso.

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #88 en: 27-02-2012, 23:58 (Lunes) »
voy a girar los cables haber que pasa

eduardorq

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #89 en: 05-06-2012, 14:49 (Martes) »
Perdón... acabo de caer que esto es preguntando por firmware de DD-WRT.... yo el vídeo que he puesto se basa en OpenWrt... no sé si funcionaría igual, sería interesante que alguien lo probara y lo confirmase.

Buscando solución para esto mismo que me pasó con el mismo router, aunque sé que hace tiempo ya y el post es viejo pero le puede servir a alguien más que llegue aquí buscando alguna solución



El vídeo da la solución
« Última modificación: 05-06-2012, 15:02 (Martes) por eduardorq »

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #90 en: 05-06-2012, 16:38 (Martes) »
no funciona

tal como lo enciendes te devuelve sin problemas el ping pero no se puede entrar por telnet

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #91 en: 12-06-2012, 21:36 (Martes) »
bueno despues de mucho tiempo parado por falta de tiempo , tengo el cable operativo , pero ahor ano funciona el comando tpl

me da tiempo de sobra pero no se para el jodio e intenta cargar ,

tenéis alguna idea de que puedo hacer?


gracias

SERASER

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #92 en: 12-06-2012, 22:01 (Martes) »
Me ha pasado muchas veces a mi con un tp-link.

Lo deje, al tiempo repeti y wuala ya funciono.

Cambia de programa, no se cual usas pero puedes usar bajo windows putty, hyperterminal y teraterm.

Saludos.

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #93 en: 12-06-2012, 22:27 (Martes) »
estoy usando putty , voy a probar con los otros que has puesto

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #94 en: 12-06-2012, 22:47 (Martes) »
nada ninguno cuela , y necesito este router ya que el wrt54gl se me a caido al suelo y se me ha jodido una antena

SERASER

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #95 en: 12-06-2012, 22:50 (Martes) »
Pues seguro que tu adaptador serial es usb ¿verdad?

No se como pero se me arreglo solo, no te puedo decir mas.

SERASER

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #96 en: 12-06-2012, 22:55 (Martes) »
nada ninguno cuela , y necesito este router ya que el wrt54gl se me a caido al suelo y se me ha jodido una antena

El que se le haya jodido una antena al wrt54gl no es problema, le metes dd-wrt y puedes cambiar tanto Rx como Tx a la antena buena.

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #97 en: 12-06-2012, 23:10 (Martes) »
ya lo e probado , el tema es que lo tengo en modo repetidor y se nota bastante la bajada de  velocidad en la navegación

rofear

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #98 en: 13-06-2012, 12:52 (Miércoles) »
sale perfecto ,aquí os dejo la captura , pero no me pilla lo de tpl , no se puede hacer algo diferente

[spoiler]U-Boot 1.1.4 (Apr 28 2011 - 15:55:09)

AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.32.27 (eric@Osiris) (gcc version 4.3.3 (GCC) ) #3 Mon Jan 30 21:21:10 EST 2012
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR9132 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=TL-WR1043ND
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29340k/32768k available (2077k kernel code, 3428k reserved, 414k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR1043ND
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
yaffs Jan 30 2012 21:19:57 Installing.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: s25sl064a (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=520000, len=2D0000
0x000000520000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
Realtek RTL8366RB ethernet switch driver version 0.2.3
rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
rtl8366rb: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 152k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
CPU 0 Unable to handle kernel paging request at virtual address c00aa9d8, epc == 801712c8, ra == 80171240
Oops[#1]:
Cpu 0
$ 0   : 00000000 802f0000 c00aa9d8 00040000
$ 4   : fffe837c 0002837c fffc0000 80006000
$ 8   : 00002000 00000000 802ce400 ffffffff
$12   : 81907314 81907300 00000001 802c6554
$16   : 0002837b 00000005 00000000 c01be644
$20   : 00027d54 00000007 0002837c c00ab000
$24   : 00000003 80075004
$28   : 81b26000 81b27ad0 c01be000 80171240
Hi    : 00000002
Lo    : 00000000
epc   : 801712c8 0x801712c8
    Not tainted
ra    : 80171240 0x80171240
Status: 1000d003    KERNEL EXL IE
Cause : 00800008
BadVA : c00aa9d8
PrId  : 00019374 (MIPS 24Kc)
Modules linked in: gpio_buttons input_polldev input_core
Process insmod (pid: 223, threadinfo=81b26000, task=81b30d98, tls=00000000)
Stack : 81040100 00000002 800fea08 819d0000 00000005 00000022 0000001d 6d000400
        00000000 0000030d a0000000 801702f4 c0074dd0 c0069000 c007700f 0000e00f
        007179e4 0079c99b 00c660c9 00000004 000195d4 0000001c 0001cf63 00000000
        c0069000 00000003 00000003 00000001 00000000 c01be644 c01bea68 c01be664
        00000007 8144fee8 80300000 00000039 819d00e4 00000000 00000000 c007700f
        ...
Call Trace:[<800fea08>] 0x800fea08
[<801702f4>] 0x801702f4
[<80129e54>] 0x80129e54
[<80129cf0>] 0x80129cf0
[<8012646c>] 0x8012646c
[<80093740>] 0x80093740
[<80126d14>] 0x80126d14
[<80127c9c>] 0x80127c9c
[<800ae828>] 0x800ae828
[<800b68e4>] 0x800b68e4
[<800b6978>] 0x800b6978
[<800b6ec4>] 0x800b6ec4
[<800b03c4>] 0x800b03c4
[<800d8c9c>] 0x800d8c9c
[<80093740>] 0x80093740
[<800d9a54>] 0x800d9a54
[<800d9c0c>] 0x800d9c0c
[<80062544>] 0x80062544


Code: 5040fffe  00832021  02e41021 <90500000> 02f41021  a0500000  8fa400bc  1080000d  26940001
Disabling lock debugging due to kernel taint
ar71xx: pll_reg 0xb8050014: 0x1a000000
eth0: link up (1000Mbps/Full duplex)
- preinit -
[/spoiler]

victorin

  • Visitante
Re: TP-Link WR1043ND: reinstalo el firmware original desde DDWRT y bricked!!!
« Respuesta #99 en: 15-06-2012, 17:24 (Viernes) »
Hola,yo stoy como tu mas o menos...para abrir la consola debes de poner tpl o tp da lo mismo y luego darle repetidas veces al intro sin miedo  ;D  Llega una linea que pone USB Check y ahi es donde se abre el promp> si pasa ese punto reinicia y empieza.
 
Mi problema viene que pide user y pass y no lo se.... no sirve admin, root. No encuentro nada por ahi....


Un saludo