Equipos y materiales > Openwrt & LEDE
TP-LiNK TL-WR1043ND V1.10 ¿como instalo firmware por puerto serie?
(1/1)
Cristof_Romuard:
Buenas, a llegado a mis manos el router ya mencionado y tiene un OpenWRT instalado pero es completamente inaccesible vía web, ni telnet... solo lo e conseguido por puerto serie. Eso si, el cacharro da ip y demás, pero al intentar entrar con la ip que supuesta mente te da... pues como que da error y a comer pipas. La cosa es esa, que por serie si que puedo acceder y esto es lo que me dice que tiene instalado " BARRIER BREAKER (Bleeding Edge, r37801)", así que supongo que estará mal flasheado, pero es que no tengo ni idea de como flashear el firmware desde Putty... vamos que seguro que es lo mas sencillo del mundo, pero ya sabéis que para un novato todo es difícil.

Lo que me gustaría es instalar el firm de casa, y ya desde ahí me las apaño.

Si algún alma caritativa me quiere echar un cable se lo agradecería.


--- Código: ---U-Boot 1.1.4 (Mar 31 2012 - 10:40:21)

AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...



OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

[    0.000000] Linux version 3.10.4 (fnord@tschunk) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37801) ) #1 Sat Aug 17 10:29:08 UTC 2013
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9132 rev 2
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28716k/32768k available (2307k kernel code, 4052k reserved, 608k data, 216k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[    0.360000] bio: create slab <bio-0> at 0
[    0.370000] Switching to clocksource MIPS
[    0.380000] NET: Registered protocol family 2
[    0.380000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.380000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.390000] TCP: Hash tables configured (established 512 bind 512)
[    0.390000] TCP: reno registered
[    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] NET: Registered protocol family 1
[    0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.450000] msgmni has been set to 56
[    0.450000] io scheduler noop registered
[    0.450000] io scheduler deadline registered (default)
[    0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.490000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.500000] console [ttyS0] enabled, bootconsole disabled
[    0.500000] console [ttyS0] enabled, bootconsole disabled
[    0.510000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.520000] m25p80 spi0.0: found en25q64, expected m25p80
[    0.530000] m25p80 spi0.0: en25q64 (8192 Kbytes)
[    0.530000] 5 tp-link partitions found on MTD device spi0.0
[    0.540000] Creating 5 MTD partitions on "spi0.0":
[    0.540000] 0x000000000000-0x000000020000 : "u-boot"
[    0.550000] 0x000000020000-0x000000124a00 : "kernel"
[    0.550000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.570000] 0x000000124a00-0x0000007f0000 : "rootfs"
[    0.570000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.590000] mtd: partition "rootfs" set to be root filesystem
[    0.590000] mtd: partition "rootfs_data" created automatically, ofs=0x410000, len=0x3e0000
[    0.600000] 0x000000410000-0x0000007f0000 : "rootfs_data"
[    0.610000] 0x0000007f0000-0x000000800000 : "art"
[    0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.4
[    0.740000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[    0.740000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.920000] libphy: rtl8366rb: probed
[    0.930000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    1.240000] TCP: cubic registered
[    1.240000] NET: Registered protocol family 17
[    1.250000] Bridge firewalling registered
[    1.250000] 8021q: 802.1Q VLAN Support v1.8
[    1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.270000] Freeing unused kernel memory: 216K (8033a000 - 80370000)
procd: Console is alive
procd: - watchdog -
[    3.350000] usbcore: registered new interface driver usbfs
[    3.350000] usbcore: registered new interface driver hub
[    3.360000] usbcore: registered new device driver usb
[    3.470000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.480000] ehci-platform: EHCI generic platform driver
[    3.480000] ehci-platform ehci-platform: EHCI Host Controller
[    3.490000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    3.500000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    3.520000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    3.520000] hub 1-0:1.0: USB hub found
[    3.530000] hub 1-0:1.0: 1 port detected
procd: - preinit -
[    3.810000] eth0: link up (1000Mbps/Full duplex)
mount_root: jffs2 is ready
[    4.000000] jffs2: notice: (304) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead, 0 orphan) found.
[    4.030000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[    6.300000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[    6.300000] Backport generated by backports.git backports-20130617-4-ge3220f5
[    6.340000] cfg80211: Calling CRDA to update world regulatory domain
[    6.340000] cfg80211: World regulatory domain updated:
[    6.350000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    6.360000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.370000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    6.370000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    6.380000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.390000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.120000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[    7.130000] cfg80211: Calling CRDA for country: US
[    7.130000] cfg80211: Regulatory domain changed to country: US
[    7.140000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.150000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    7.160000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    7.160000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.170000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.180000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.190000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    7.310000] tun: Universal TUN/TAP device driver, 1.6
[    7.310000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    7.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.510000] xt_time: kernel timezone is -0000
[    7.530000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
[   11.060000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[   11.060000] eth0: link up (1000Mbps/Full duplex)
[   11.070000] device eth0.1 entered promiscuous mode
[   11.070000] device eth0 entered promiscuous mode
[   11.090000] br-lan_vpn: port 1(eth0.1) entered forwarding state
[   11.090000] br-lan_vpn: port 1(eth0.1) entered forwarding state
[   13.090000] br-lan_vpn: port 1(eth0.1) entered forwarding state
[   17.850000] device wlan0 entered promiscuous mode
procd: - init complete -
trl


BusyBox v1.19.4 (2013-08-17 10:20:27 UTC) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r37801)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/#

--- Fin del código ---

Tki2000:

--- Cita de: Cristof_Romuard en 26-03-2016, 23:18 (Sábado) ---Buenas, a llegado a mis manos el router ya mencionado y tiene un OpenWRT instalado pero es completamente inaccesible vía web, ni telnet... solo lo e conseguido por puerto serie. Eso si, el cacharro da ip y demás, pero al intentar entrar con la ip que supuesta mente te da... pues como que da error y a comer pipas. La cosa es esa, que por serie si que puedo acceder y esto es lo que me dice que tiene instalado " BARRIER BREAKER (Bleeding Edge, r37801)", así que supongo que estará mal flasheado, pero es que no tengo ni idea de como flashear el firmware desde Putty... vamos que seguro que es lo mas sencillo del mundo, pero ya sabéis que para un novato todo es difícil.

Lo que me gustaría es instalar el firm de casa, y ya desde ahí me las apaño.

Si algún alma caritativa me quiere echar un cable se lo agradecería.


--- Código: ---U-Boot 1.1.4 (Mar 31 2012 - 10:40:21)

AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...



OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

[    0.000000] Linux version 3.10.4 (fnord@tschunk) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37801) ) #1 Sat Aug 17 10:29:08 UTC 2013
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9132 rev 2
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28716k/32768k available (2307k kernel code, 4052k reserved, 608k data, 216k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[    0.360000] bio: create slab <bio-0> at 0
[    0.370000] Switching to clocksource MIPS
[    0.380000] NET: Registered protocol family 2
[    0.380000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.380000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.390000] TCP: Hash tables configured (established 512 bind 512)
[    0.390000] TCP: reno registered
[    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] NET: Registered protocol family 1
[    0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.450000] msgmni has been set to 56
[    0.450000] io scheduler noop registered
[    0.450000] io scheduler deadline registered (default)
[    0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.490000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.500000] console [ttyS0] enabled, bootconsole disabled
[    0.500000] console [ttyS0] enabled, bootconsole disabled
[    0.510000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.520000] m25p80 spi0.0: found en25q64, expected m25p80
[    0.530000] m25p80 spi0.0: en25q64 (8192 Kbytes)
[    0.530000] 5 tp-link partitions found on MTD device spi0.0
[    0.540000] Creating 5 MTD partitions on "spi0.0":
[    0.540000] 0x000000000000-0x000000020000 : "u-boot"
[    0.550000] 0x000000020000-0x000000124a00 : "kernel"
[    0.550000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.570000] 0x000000124a00-0x0000007f0000 : "rootfs"
[    0.570000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.590000] mtd: partition "rootfs" set to be root filesystem
[    0.590000] mtd: partition "rootfs_data" created automatically, ofs=0x410000, len=0x3e0000
[    0.600000] 0x000000410000-0x0000007f0000 : "rootfs_data"
[    0.610000] 0x0000007f0000-0x000000800000 : "art"
[    0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.4
[    0.740000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[    0.740000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.920000] libphy: rtl8366rb: probed
[    0.930000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    1.240000] TCP: cubic registered
[    1.240000] NET: Registered protocol family 17
[    1.250000] Bridge firewalling registered
[    1.250000] 8021q: 802.1Q VLAN Support v1.8
[    1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.270000] Freeing unused kernel memory: 216K (8033a000 - 80370000)
procd: Console is alive
procd: - watchdog -
[    3.350000] usbcore: registered new interface driver usbfs
[    3.350000] usbcore: registered new interface driver hub
[    3.360000] usbcore: registered new device driver usb
[    3.470000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.480000] ehci-platform: EHCI generic platform driver
[    3.480000] ehci-platform ehci-platform: EHCI Host Controller
[    3.490000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    3.500000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    3.520000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    3.520000] hub 1-0:1.0: USB hub found
[    3.530000] hub 1-0:1.0: 1 port detected
procd: - preinit -
[    3.810000] eth0: link up (1000Mbps/Full duplex)
mount_root: jffs2 is ready
[    4.000000] jffs2: notice: (304) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead, 0 orphan) found.
[    4.030000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[    6.300000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[    6.300000] Backport generated by backports.git backports-20130617-4-ge3220f5
[    6.340000] cfg80211: Calling CRDA to update world regulatory domain
[    6.340000] cfg80211: World regulatory domain updated:
[    6.350000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    6.360000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.370000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    6.370000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    6.380000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.390000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.120000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[    7.130000] cfg80211: Calling CRDA for country: US
[    7.130000] cfg80211: Regulatory domain changed to country: US
[    7.140000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.150000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    7.160000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    7.160000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.170000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.180000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.190000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    7.310000] tun: Universal TUN/TAP device driver, 1.6
[    7.310000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    7.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.510000] xt_time: kernel timezone is -0000
[    7.530000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
[   11.060000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[   11.060000] eth0: link up (1000Mbps/Full duplex)
[   11.070000] device eth0.1 entered promiscuous mode
[   11.070000] device eth0 entered promiscuous mode
[   11.090000] br-lan_vpn: port 1(eth0.1) entered forwarding state
[   11.090000] br-lan_vpn: port 1(eth0.1) entered forwarding state
[   13.090000] br-lan_vpn: port 1(eth0.1) entered forwarding state
[   17.850000] device wlan0 entered promiscuous mode
procd: - init complete -
trl


BusyBox v1.19.4 (2013-08-17 10:20:27 UTC) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r37801)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/#

--- Fin del código ---



--- Fin de la cita ---

Se me ocurre, que ya que tienes acceso por puerto serie, lo devuelvas a los valores por defecto de openwrt.

--- Código: ---mtd -r erase rootfs_data

--- Fin del código ---
Tras eso deberías poder acceder a la IP 192.168.1.1 como si acabaras de instalar openwrt.
Cristof_Romuard:
Pues no, lo hice como decías, pero no pude acceder vía web, pero no te preocupes, encontré un tutorial en youtube. Borre todo excepto el bootloader y reinstale el firm original, así que ya esta todo listo.

Gracias por la ayuda.

PD: Si necesitáis el tuto pedídmelo, ya que no se si se puede poner aquí directamente.
Tki2000:

--- Cita de: Cristof_Romuard en 27-03-2016, 18:52 (Domingo) ---Pues no, lo hice como decías, pero no pude acceder vía web, pero no te preocupes, encontré un tutorial en youtube. Borre todo excepto el bootloader y reinstale el firm original, así que ya esta todo listo.

Gracias por la ayuda.

PD: Si necesitáis el tuto pedídmelo, ya que no se si se puede poner aquí directamente.

--- Fin de la cita ---

Seguramente no tendría luci instalado. De todas formas me alegro de que lo solucionaras.
Navegación
Índice de Mensajes

Ir a la versión completa