Autor Tema: Telsey 502 de tele2 (Leído 41221 veces)

danitool · « **Respuesta #20 en:** 25-01-2013, 17:11 (Viernes) »

He compilado Backfire con soporte para esta placa
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire.zip

La única pega es que este router necesita un arreglo después del primer inicio haciendo el comando:

Código: [Seleccionar]

mtd fixtrx linuxy ni idea si funcionará.

También traté de nuevo corregir el eth1. Por favor pon un log de arranque completo. pero en modo texto, en tus capturas de pantalla no se ve nada....no hagas capturas, solo copia y pégame el texto.
Si quieres pegalo aquí, o en pastebin. Sino será imposible intentar corregir ningún fallo.

javier1990 · « **Respuesta #21 en:** 25-01-2013, 17:40 (Viernes) »

salvador prueba con estos pin del jtag parecen que son los mismo que el comtred perdonad por el copy y paste http://img502.imageshack.us/img502/9981/20120204173016.jpg

javier1990 · « **Respuesta #22 en:** 25-01-2013, 18:24 (Viernes) »

CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 9
web info: Waiting for connection on socket 0.
CFE>
web info: Waiting for connection on socket 1.
web info: Waiting for connection on socket 0.
web info: Upload 3014660 bytes, Telsey image format.
CFE>
Flashing root file system and kernel at 0xbfc10000: ............................ ...................

.
*** Image flash done *** !
Resetting board...ÿ

CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x8042080 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #7 Fri Jan 25 17: 02:12 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd cons ole=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1986k kernel code, 2820k reserved, 362k data, 1 36k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Â© 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx_flash: Failed to probe using CFI/JEDEC
bcm963xx-flash: probe of bcm963xx-flash.0 failed with error -5
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "mtdblock2" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

javier1990 · « **Respuesta #23 en:** 25-01-2013, 18:40 (Viernes) »

es lo mismo que pone con el backfire de la pagina

danitool · « **Respuesta #24 en:** 25-01-2013, 19:03 (Viernes) »

Prueba de nuevo con este

https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire2.zip

Y pon de nuevo el log de arranque

javier1990 · « **Respuesta #25 en:** 25-01-2013, 20:54 (Viernes) »

CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #8 Fri Jan 25 18:59:18 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1988k kernel code, 2820k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Â© 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 30000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length cff00
bcm963xx_flash: Partition 2 is rootfs offset e0000 and length 310000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 30000 and length 3c0000
bcm963xx_flash: Spare partition is 2f0000 offset and length 100000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000030000 : "CFE"
0x000000010100-0x0000000e0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000e0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000
0x0000002f0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000030000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
device eth0 entered promiscuous mode
PHY 1:1f not found
bcm63xx_enet bcm63xx_enet.1: could not attach to PHY
PHY 1:1f not found
bcm63xx_enet bcm63xx_enet.1: could not attach to PHY
device eth1 entered promiscuous mode
PHY 1:1f not found
bcm63xx_enet bcm63xx_enet.1: could not attach to PHY
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
eth0: link UP - 100/full - flow control off
br-lan: port 1(eth0) entering forwarding state
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (214 buckets, 856 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay

javier1990 · « **Respuesta #26 en:** 25-01-2013, 20:55 (Viernes) »

ya funcion parece que package tengo quer instalar los de backfire

danitool · « **Respuesta #27 en:** 25-01-2013, 21:16 (Viernes) »

Que es lo que funciona, el eth1 no parece que funcione o al menos marca eso el log.

Prueba de nuevo este firmware
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire3.zip
y pega de nuevo el log de arranque

javier1990 · « **Respuesta #28 en:** 26-01-2013, 00:45 (Sábado) »

el frimware no se que da instalado verda danitool cada vez que lo desconecto de la luz se va todo lo que echo. mañana te subo el log

danitool · « **Respuesta #29 en:** 26-01-2013, 00:48 (Sábado) »

Cita de: javier1990 en 26-01-2013, 00:45 (Sábado)

el frimware no se que da instalado verda danitool cada vez que lo desconecto de la luz se va todo lo que echo. mañana te subo el log

Ya dije que después del primer inicio hay que hacer el comando

Código: [Seleccionar]

mtd fixtrx linuxel cual no sé si funcionará, ya que no estaba disponible en Backfire pero traté de hacer un backport, así que después de iniciarlo por primera vez prueba el comando. Sino funciona la cosa se complicaría para hacer funcionar el router en Backfire.

javier1990 · « **Respuesta #30 en:** 26-01-2013, 16:25 (Sábado) »

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #9 Fri Jan 25 21:10:38 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1988k kernel code, 2820k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 30000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length cff00
bcm963xx_flash: Partition 2 is rootfs offset e0000 and length 310000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 30000 and length 3c0000
bcm963xx_flash: Spare partition is 2f0000 offset and length 100000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000030000 : "CFE"
0x000000010100-0x0000000e0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000e0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000
0x0000002f0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000030000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
device eth0 entered promiscuous mode
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 2(eth1) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
eth0: link UP - 100/full - flow control off
br-lan: port 1(eth0) entering forwarding state
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (214 buckets, 856 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay

BusyBox v1.15.3 (2013-01-09 20:58:29 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/#

javier1990 · « **Respuesta #31 en:** 26-01-2013, 16:26 (Sábado) »

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/# passwd
Changing password for root
New password:
Bad password: too short
Retype password:
Password for root changed by root
root@OpenWrt:/# mtd fixtrx linux
Trying to fix trx header in linux at 0x0...
Verifying we actually have an imagetag.
Tag verify failed. This may not be a valid image.
root@OpenWrt:/#

danitool · « **Respuesta #32 en:** 26-01-2013, 17:57 (Sábado) »

Otra imagen para probar

https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire4.zip

A ver si en esta te funciona

Código: [Seleccionar]

mtd fixtrx linuxPon de nuevo el log de arranque, de paso estoy intentando saber cual es la phy_id del eth1 (hay 31 posibles).

javier1990 · « **Respuesta #33 en:** 26-01-2013, 22:43 (Sábado) »

CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #11 Sat Jan 26 17:50:58 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1988k kernel code, 2820k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Â© 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length cff00
bcm963xx_flash: Partition 2 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 3 is linux offset 10000 and length 3f0000
bcm963xx_flash: Spare partition is e0000 offset and length 310000
Creating 4 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000e0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x000000400000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008000: 0x674f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008004: 0x4272 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008020: 0x7365 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008024: 0x696f instead
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 7, bad_blocks 0, c->nr_blocks 8
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00 64 mtdblock0 (driver?)
1f01 831 mtdblock1 (driver?)
1f02 64 mtdblock2 (driver?)
1f03 4032 mtdblock3 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)

danitool · « **Respuesta #34 en:** 26-01-2013, 22:54 (Sábado) »

Eso fue después de hacer?
mtd fixtrx linux
porque sino fue así no tiene mucho sentido que la anterior imagen funcionase y esta no

danitool · « **Respuesta #35 en:** 27-01-2013, 15:15 (Domingo) »

Otra compilación para probar

https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire5.zip

javier1990 · « **Respuesta #36 en:** 27-01-2013, 15:55 (Domingo) »

te comento danitool despues de instalar la imagen cuando llega a root@ yo le pongo este comando y lo reconoce pero cuando vuelvo a iniciar en serial me salta esto
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #1 Sun Jan 27 15:10:26 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13472k/16384k available (2053k kernel code, 2912k reserved, 361k data, 132k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.312:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Â© 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 3 is linux offset 10000 and length 3f0000
bcm963xx_flash: Spare partition is f0000 offset and length 300000
Creating 4 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x000000400000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008000: 0x674f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008004: 0x4272 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008020: 0x7365 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008024: 0x696f instead
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 7, bad_blocks 0, c->nr_blocks 8
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00 64 mtdblock0 (driver?)
1f01 895 mtdblock1 (driver?)
1f02 64 mtdblock2 (driver?)
1f03 4032 mtdblock3 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)

danitool · « **Respuesta #37 en:** 27-01-2013, 16:45 (Domingo) »

¿y que hay del eth1 en este último firmware cuando lo inicias por primera vez?

danitool · « **Respuesta #38 en:** 27-01-2013, 20:53 (Domingo) »

Otro firmware Backfire más para probar

https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire6.zip

Esta vez después de hacer mtd fixtrx linux debiera funcionar el siguiente reinicio, y todos los posteriores.

Todavía no sé nada acerca del eth1. Desgraciadamente con un feedback tan pésimo, poco se puede hacer.

De todas formas pon el bootlog de nuevo sino es mucha molestia.

javier1990 · « **Respuesta #39 en:** 28-01-2013, 14:39 (Lunes) »

Copyright (C) 2003,2004,2005 Telsey Telecommunications.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)

Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16

mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #2 Sun Jan 27 20:42:36 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13472k/16384k available (2053k kernel code, 2912k reserved, 360k data, 132k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.312:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Â© 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
bcm963xx_flash: Spare partition is 280000 offset and length 170000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=280000, len=170000
0x000000280000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 132k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Generic PHY]
device eth1 entered promiscuous mode
eth0: link UP - 100/full - flow control off
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (212 buckets, 848 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected

BusyBox v1.15.3 (2013-01-27 14:49:55 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/# passwd
Changing password for root
New password:
Bad password: too short
Retype password:
Password for root changed by root
root@OpenWrt:/#

Noticias:

Autor Tema: Telsey 502 de tele2 (Leído 41221 veces)

danitool

javier1990

javier1990

javier1990

danitool

javier1990

javier1990

danitool

javier1990

danitool

javier1990

javier1990

danitool

javier1990

danitool

danitool

javier1990

danitool

danitool

javier1990