El pais en el apartado wifi si esta puesto. Aqui va el dmesg:
[ 0.000000] Linux version 3.18.11 (openwrt@gb-11) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45676) ) #1 Wed May 13 01:51:36 UTC 2015
[ 0.000000] MyLoader: sysp=84c31530, boardp=0065cbe4, parts=195ef6a4
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803842b0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125724K/131072K available (2634K kernel code, 128K rwdata, 548K rodata, 264K init, 194K bss, 5348K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.330000] PCI host bridge to bus 0000:00
[ 0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.340000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.350000] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
[ 0.350000] pci 0000:00:00.0: invalid calibration data
[ 0.350000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.350000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.350000] pci 0000:00:00.0: supports D1
[ 0.350000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.350000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.360000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.370000] Switched to clocksource MIPS
[ 0.370000] NET: Registered protocol family 2
[ 0.380000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.390000] TCP: reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.410000] PCI: CLS 0 bytes, default 32
[ 0.410000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 245
[ 0.460000] io scheduler noop registered
[ 0.460000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] console [ttyS0] disabled
[ 0.500000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.510000] console [ttyS0] enabled
[ 0.510000] bootconsole [early0] disabled
[ 0.520000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.530000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.540000] 5 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 5 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.550000] 0x000000020000-0x000000143e38 : "kernel"
[ 0.560000] 0x000000143e38-0x0000007f0000 : "rootfs"
[ 0.560000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.580000] 0x000000330000-0x0000007f0000 : "rootfs_data"
[ 0.580000] 0x0000007f0000-0x000000800000 : "art"
[ 0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.610000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 0.670000] libphy: ag71xx_mdio: probed
[ 1.270000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 1.280000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.290000] TCP: cubic registered
[ 1.290000] NET: Registered protocol family 17
[ 1.290000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.310000] Bridge firewalling registered
[ 1.310000] 8021q: 802.1Q VLAN Support v1.8
[ 1.320000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.330000] Freeing unused kernel memory: 264K (8039e000 - 803e0000)
[ 2.320000] init: failed to symlink /tmp -> /var
[ 2.330000] init: Console is alive
[ 2.330000] init: - watchdog -
[ 3.510000] usbcore: registered new interface driver usbfs
[ 3.510000] usbcore: registered new interface driver hub
[ 3.520000] usbcore: registered new device driver usb
[ 3.530000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.540000] ehci-platform: EHCI generic platform driver
[ 3.540000] ehci-platform ehci-platform: EHCI Host Controller
[ 3.550000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 3.560000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 3.590000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 3.590000] hub 1-0:1.0: USB hub found
[ 3.600000] hub 1-0:1.0: 1 port detected
[ 3.600000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.610000] ohci-platform: OHCI generic platform driver
[ 3.920000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 4.070000] hub 1-1:1.0: USB hub found
[ 4.070000] hub 1-1:1.0: 4 ports detected
[ 4.330000] init: - preinit -
[ 4.930000] random: procd urandom read with 8 bits of entropy available
[ 6.310000] eth0: link up (1000Mbps/Full duplex)
[ 8.200000] jffs2: notice: (396) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 2 of xref (0 dead, 0 orphan) found.
[ 8.220000] mount_root: switching to jffs2 overlay
[ 8.260000] eth0: link down
[ 8.290000] procd: - early -
[ 8.300000] procd: - watchdog -
[ 9.020000] procd: - ubus -
[ 10.030000] procd: - init -
[ 10.790000] NET: Registered protocol family 10
[ 10.800000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.810000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 10.820000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 10.830000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.850000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 10.890000] xt_time: kernel timezone is -0000
[ 10.930000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.930000] cfg80211: World regulatory domain updated:
[ 10.940000] cfg80211: DFS Master region: unset
[ 10.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.950000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.960000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.970000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.980000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.980000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.990000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.000000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.010000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.090000] PPP generic driver version 2.4.2
[ 11.100000] NET: Registered protocol family 24
[ 11.150000] ath: EEPROM regdomain: 0x0
[ 11.150000] ath: EEPROM indicates default country code should be used
[ 11.150000] ath: doing EEPROM country->regdmn map search
[ 11.150000] ath: country maps to regdmn code: 0x3a
[ 11.150000] ath: Country alpha2 being used: US
[ 11.150000] ath: Regpair used: 0x3a
[ 11.160000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.160000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 11.170000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 11.180000] Data bus error, epc == 872838a8, ra == 872838a8
[ 11.180000] Oops[#1]:
[ 11.180000] CPU: 0 PID: 607 Comm: kmodloader Not tainted 3.18.11 #1
[ 11.180000] task: 879cd360 ti: 87af6000 task.ti: 87af6000
[ 11.180000] $ 0 : 00000000 00000000 deadc0de 872e12c0
[ 11.180000] $ 4 : b0007044 00007044 00000004 00000002
[ 11.180000] $ 8 : 87af7b80 00000000 00000000 00000000
[ 11.180000] $12 : 00000000 00000007 00000000 00000000
[ 11.180000] $16 : 8735a010 0000000f 00007044 00002710
[ 11.180000] $20 : 0000000f 00000002 00000000 8038732c
[ 11.180000] $24 : 00000000 8006ad4c
[ 11.180000] $28 : 87af6000 87af7b10 00000000 872838a8
[ 11.180000] Hi : 00000004
[ 11.180000] Lo : b2d8c000
[ 11.180000] epc : 872838a8 ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 11.180000] Not tainted
[ 11.180000] ra : 872838a8 ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 11.180000] Status: 1100dc03 KERNEL EXL IE
[ 11.180000] Cause : 0080001c
[ 11.180000] PrId : 0001974c (MIPS 74Kc)
[ 11.180000] Modules linked in: ath9k(+) ath9k_common pppoe ppp_async iptable_nat ath9k_hw ath pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_masquerade_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack_ftp nf_conntrack iptable_raw iptable_mangle iptable_filter ip_tables crc_ccitt compat ledtrig_usbdev ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables ipv6 arc4 crypto_blkcipher ohci_platform ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[ 11.180000] Process kmodloader (pid: 607, threadinfo=87af6000, task=879cd360, tls=7753a440)
[ 11.180000] Stack : 871aedc8 00000018 00000000 800ce94c 00000002 8735a010 00000000 87390b00
[ 11.180000] 8038732c 8735a038 8735a010 87283f38 871aedc4 00000005 000000d0 872f0000
[ 11.180000] 000186a0 873915cc 87af7be8 8735a010 8735a038 87285a18 87af7bfc 87391720
[ 11.180000] 000080d0 800f91d4 87af7b80 87384880 00000008 8735a038 8038732c 87af7be8
[ 11.180000] 87391720 8735a010 87390b00 8038732c 8735a038 8735a010 00000000 8038732c
[ 11.180000] ...
[ 11.180000] Call Trace:
[ 11.180000] [<872838a8>] ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 11.180000] [<87283f38>] ath9k_hw_reset_tsf+0x644/0x684 [ath9k_hw]
[ 11.180000]
[ 11.180000]
[ 11.180000] Code: 02402821 0060f809 00000000 <00541024> 10550008 24020001 0c069f8c 2404000a 09ca0e24
[ 11.420000] ---[ end trace 81a8bccab4cc86c8 ]---
[ 11.430000] cfg80211: Calling CRDA for country: US
[ 11.440000] cfg80211: Regulatory domain changed to country: US
[ 11.450000] cfg80211: DFS Master region: FCC
[ 11.450000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.460000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.470000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 11.480000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 11.490000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.500000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 19.010000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.030000] device eth0.1 entered promiscuous mode
[ 19.030000] device eth0 entered promiscuous mode
[ 19.050000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.070000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 19.500000] eth0: link up (1000Mbps/Full duplex)
[ 19.500000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.650000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.650000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.660000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 19.660000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 19.810000] cfg80211: Calling CRDA for country: ES
[ 19.840000] cfg80211: Regulatory domain changed to country: ES
[ 19.840000] cfg80211: DFS Master region: ETSI
[ 19.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.860000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.860000] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 19.870000] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 19.880000] cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[ 19.890000] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 21.500000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 1 is up
[ 21.650000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.770000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.780000] device wlan0 entered promiscuous mode
[ 21.780000] br-lan: port 2(wlan0) entered forwarding state
[ 21.790000] br-lan: port 2(wlan0) entered forwarding state
[ 21.840000] br-lan: port 2(wlan0) entered disabled state
[ 22.180000] br-lan: port 2(wlan0) entered forwarding state
[ 22.180000] br-lan: port 2(wlan0) entered forwarding state
[ 22.190000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 24.180000] br-lan: port 2(wlan0) entered forwarding state
[ 45.480000] random: nonblocking pool is initialized
[ 151.000000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.