Seguridad Wireless - Wifi
Equipos y materiales => Puntos de acceso, routers, switchs y bridges => Openwrt & LEDE => Mensaje iniciado por: zoylorino en 16-05-2015, 14:35 (Sábado)
-
Hola. Tengo un wdr3600 con OpenWrt instalado pero no consigo que me funcione el wifi 5Ghz. He instalado multiples versiones pero en ninguna detecta el chip wifi 5Ghz. ¿Le ha pasado a alguien?. Gracias y saludos.
-
Yo tengo uno, y funciona ambas bandas perfectamente.
Postea el resultado del comando dmesg para ver si se localiza el problema.
Por cierto has configurado correctamente el país, etc. ?
Enviado desde uno de mis 'cacharros' usando Tapatalk
-
El pais en el apartado wifi si esta puesto. Aqui va el dmesg:
[ 0.000000] Linux version 3.18.11 (openwrt@gb-11) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45676) ) #1 Wed May 13 01:51:36 UTC 2015
[ 0.000000] MyLoader: sysp=84c31530, boardp=0065cbe4, parts=195ef6a4
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803842b0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125724K/131072K available (2634K kernel code, 128K rwdata, 548K rodata, 264K init, 194K bss, 5348K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.330000] PCI host bridge to bus 0000:00
[ 0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.340000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.350000] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
[ 0.350000] pci 0000:00:00.0: invalid calibration data
[ 0.350000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.350000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.350000] pci 0000:00:00.0: supports D1
[ 0.350000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.350000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.360000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.370000] Switched to clocksource MIPS
[ 0.370000] NET: Registered protocol family 2
[ 0.380000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.390000] TCP: reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.410000] PCI: CLS 0 bytes, default 32
[ 0.410000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 245
[ 0.460000] io scheduler noop registered
[ 0.460000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] console [ttyS0] disabled
[ 0.500000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.510000] console [ttyS0] enabled
[ 0.510000] bootconsole [early0] disabled
[ 0.520000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.530000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.540000] 5 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 5 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.550000] 0x000000020000-0x000000143e38 : "kernel"
[ 0.560000] 0x000000143e38-0x0000007f0000 : "rootfs"
[ 0.560000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.580000] 0x000000330000-0x0000007f0000 : "rootfs_data"
[ 0.580000] 0x0000007f0000-0x000000800000 : "art"
[ 0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.610000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 0.670000] libphy: ag71xx_mdio: probed
[ 1.270000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 1.280000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.290000] TCP: cubic registered
[ 1.290000] NET: Registered protocol family 17
[ 1.290000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.310000] Bridge firewalling registered
[ 1.310000] 8021q: 802.1Q VLAN Support v1.8
[ 1.320000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.330000] Freeing unused kernel memory: 264K (8039e000 - 803e0000)
[ 2.320000] init: failed to symlink /tmp -> /var
[ 2.330000] init: Console is alive
[ 2.330000] init: - watchdog -
[ 3.510000] usbcore: registered new interface driver usbfs
[ 3.510000] usbcore: registered new interface driver hub
[ 3.520000] usbcore: registered new device driver usb
[ 3.530000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.540000] ehci-platform: EHCI generic platform driver
[ 3.540000] ehci-platform ehci-platform: EHCI Host Controller
[ 3.550000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 3.560000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 3.590000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 3.590000] hub 1-0:1.0: USB hub found
[ 3.600000] hub 1-0:1.0: 1 port detected
[ 3.600000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.610000] ohci-platform: OHCI generic platform driver
[ 3.920000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 4.070000] hub 1-1:1.0: USB hub found
[ 4.070000] hub 1-1:1.0: 4 ports detected
[ 4.330000] init: - preinit -
[ 4.930000] random: procd urandom read with 8 bits of entropy available
[ 6.310000] eth0: link up (1000Mbps/Full duplex)
[ 8.200000] jffs2: notice: (396) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 2 of xref (0 dead, 0 orphan) found.
[ 8.220000] mount_root: switching to jffs2 overlay
[ 8.260000] eth0: link down
[ 8.290000] procd: - early -
[ 8.300000] procd: - watchdog -
[ 9.020000] procd: - ubus -
[ 10.030000] procd: - init -
[ 10.790000] NET: Registered protocol family 10
[ 10.800000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.810000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 10.820000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 10.830000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.850000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 10.890000] xt_time: kernel timezone is -0000
[ 10.930000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.930000] cfg80211: World regulatory domain updated:
[ 10.940000] cfg80211: DFS Master region: unset
[ 10.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.950000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.960000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.970000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.980000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.980000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.990000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.000000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.010000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.090000] PPP generic driver version 2.4.2
[ 11.100000] NET: Registered protocol family 24
[ 11.150000] ath: EEPROM regdomain: 0x0
[ 11.150000] ath: EEPROM indicates default country code should be used
[ 11.150000] ath: doing EEPROM country->regdmn map search
[ 11.150000] ath: country maps to regdmn code: 0x3a
[ 11.150000] ath: Country alpha2 being used: US
[ 11.150000] ath: Regpair used: 0x3a
[ 11.160000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.160000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 11.170000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 11.180000] Data bus error, epc == 872838a8, ra == 872838a8
[ 11.180000] Oops[#1]:
[ 11.180000] CPU: 0 PID: 607 Comm: kmodloader Not tainted 3.18.11 #1
[ 11.180000] task: 879cd360 ti: 87af6000 task.ti: 87af6000
[ 11.180000] $ 0 : 00000000 00000000 deadc0de 872e12c0
[ 11.180000] $ 4 : b0007044 00007044 00000004 00000002
[ 11.180000] $ 8 : 87af7b80 00000000 00000000 00000000
[ 11.180000] $12 : 00000000 00000007 00000000 00000000
[ 11.180000] $16 : 8735a010 0000000f 00007044 00002710
[ 11.180000] $20 : 0000000f 00000002 00000000 8038732c
[ 11.180000] $24 : 00000000 8006ad4c
[ 11.180000] $28 : 87af6000 87af7b10 00000000 872838a8
[ 11.180000] Hi : 00000004
[ 11.180000] Lo : b2d8c000
[ 11.180000] epc : 872838a8 ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 11.180000] Not tainted
[ 11.180000] ra : 872838a8 ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 11.180000] Status: 1100dc03 KERNEL EXL IE
[ 11.180000] Cause : 0080001c
[ 11.180000] PrId : 0001974c (MIPS 74Kc)
[ 11.180000] Modules linked in: ath9k(+) ath9k_common pppoe ppp_async iptable_nat ath9k_hw ath pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_masquerade_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack_ftp nf_conntrack iptable_raw iptable_mangle iptable_filter ip_tables crc_ccitt compat ledtrig_usbdev ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables ipv6 arc4 crypto_blkcipher ohci_platform ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[ 11.180000] Process kmodloader (pid: 607, threadinfo=87af6000, task=879cd360, tls=7753a440)
[ 11.180000] Stack : 871aedc8 00000018 00000000 800ce94c 00000002 8735a010 00000000 87390b00
[ 11.180000] 8038732c 8735a038 8735a010 87283f38 871aedc4 00000005 000000d0 872f0000
[ 11.180000] 000186a0 873915cc 87af7be8 8735a010 8735a038 87285a18 87af7bfc 87391720
[ 11.180000] 000080d0 800f91d4 87af7b80 87384880 00000008 8735a038 8038732c 87af7be8
[ 11.180000] 87391720 8735a010 87390b00 8038732c 8735a038 8735a010 00000000 8038732c
[ 11.180000] ...
[ 11.180000] Call Trace:
[ 11.180000] [<872838a8>] ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 11.180000] [<87283f38>] ath9k_hw_reset_tsf+0x644/0x684 [ath9k_hw]
[ 11.180000]
[ 11.180000]
[ 11.180000] Code: 02402821 0060f809 00000000 <00541024> 10550008 24020001 0c069f8c 2404000a 09ca0e24
[ 11.420000] ---[ end trace 81a8bccab4cc86c8 ]---
[ 11.430000] cfg80211: Calling CRDA for country: US
[ 11.440000] cfg80211: Regulatory domain changed to country: US
[ 11.450000] cfg80211: DFS Master region: FCC
[ 11.450000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.460000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.470000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 11.480000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 11.490000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.500000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 19.010000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.030000] device eth0.1 entered promiscuous mode
[ 19.030000] device eth0 entered promiscuous mode
[ 19.050000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.070000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 19.500000] eth0: link up (1000Mbps/Full duplex)
[ 19.500000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.650000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.650000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.660000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 19.660000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 19.810000] cfg80211: Calling CRDA for country: ES
[ 19.840000] cfg80211: Regulatory domain changed to country: ES
[ 19.840000] cfg80211: DFS Master region: ETSI
[ 19.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.860000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.860000] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 19.870000] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 19.880000] cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[ 19.890000] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 21.500000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 1 is up
[ 21.650000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.770000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.780000] device wlan0 entered promiscuous mode
[ 21.780000] br-lan: port 2(wlan0) entered forwarding state
[ 21.790000] br-lan: port 2(wlan0) entered forwarding state
[ 21.840000] br-lan: port 2(wlan0) entered disabled state
[ 22.180000] br-lan: port 2(wlan0) entered forwarding state
[ 22.180000] br-lan: port 2(wlan0) entered forwarding state
[ 22.190000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 24.180000] br-lan: port 2(wlan0) entered forwarding state
[ 45.480000] random: nonblocking pool is initialized
[ 151.000000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
-
Has probado con la versión estable de Attitude Adjustment ?
-
He probado muchas. ¿Esa es la que tu tienes instalada?. ¿Puedes poner el enlace de descarga?. Gracias.
-
He probado muchas. ¿Esa es la que tu tienes instalada?. ¿Puedes poner el enlace de descarga?. Gracias.
No. Yo tengo una compilación personalizada (porque necesito FPU emulation activado en el kernel).
Si quieres, la localizo y la cuelgo, pero si has probado varias y con ninguna te va ... mal asunto.
-
Igual es una tontería, pero... ¿estás seguro de que no tienes el wifi desactivado, en el interruptor que hay en la parte trasera del aparato (si la memoria no me falla, en OpenWrt ese botón sólo afecta al chip de los 5GHz)?
-
He probado con el firmware AA y sigue igual. Estoy sospechando que es algo hardware porque al encender el router se encienden todos los leds menos el del segundo wifi.
De todas formas muchas gracias por vuestras respuestas y por el interes.
Saludos.
-
Buenas, yo tengo un WDR3600 también y al arrancar sucede lo mismo de el led del wifi derecho, pero no se si es algo que siempre le a pasado, ahora mismo no lo puedo confirmar, lo que me sucede es que tras desbrikear por serial el equipo y volver al firm original pasando por ddwrt ahora no funciona ni 2.4GHz ni 5GHz, le he vuelto a poner ddwrt y ni si quiera aparecen las opciones de wireless.