Hola,buenas.
Yo he probado a conectar y me conecta a la primera mi serial-usb.
Los pines correctos son GND-TX-libre-RX (GND es el cuadrado sin apenas estaño) .
[spoiler]
HELO
CPUI
L1CI
HELO
CPUI
L1CI
DRAM
----
PHYS
STRF
400H
PHYE
DDR3
SIZ4
SIZ3
SIZ2
DINT
USYN
LSYN
MFAS
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
RO08
SUN2
find
flag
find
flag
SUN6
000
000
001
001
RAM2
NAN3
RFS0
NAN5
CFE version 1.0.38-114.185 for BCM963268 (32bit,SP,BE)
Build Date: Fri Sep 18 16:13:20 CST 2015 (jeremy@localhost)
Copyright (C) 2000-2011 Broadcom Corporation.
NAND flash device: name , id 0xc2da block 128KB size 262144KB
External switch id = 53125
Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000
find flag begin read flash map
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-26) : 963168MBV3
Number of MAC Addresses (1-32) : 12
Base MAC Address : e0:60:66:79:75:5e
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-9) : LE9672_ZSI
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
***************************************************
Sercomm Boot Version 1.0.2.0
***************************************************
Entering Firmware : Everything is OK.
begin check sum
safe value is 255
check sum ok
Booting from BackUp image (0xbb720000) ...
Correctable ECC Error detected: addr=0x03850600, intrCtrl=0x00000090, accessCtrl=0xF7FF1010
Correctable ECC Error detected: addr=0x0388ba00, intrCtrl=0x00000090, accessCtrl=0xF7FF1010
Correctable ECC Error detected: addr=0x0388ce00, intrCtrl=0x00000090, accessCtrl=0xF7FF1010
Decompression OK!
Entry at 0x803e1e40
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x803e1e40
Linux version 2.6.30 (sharon@ubuntu) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #3 SMP PREEMPT Tue Feb 23 10:34:27 CST 2016
BCM Flash API. Flash device is not found.
963168MBV3 prom init
CPU revision is: 0002a080 (Broadcom4350)
DSL SDRAM reserved: 0x132000
Determined physical RAM map:
memory: 07ece000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00007ece
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00007ece
On node 0 totalpages: 32462
free_area_init_node: node 0, pgdat 804dde70, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 222 pages used for memmap
Normal zone: 28144 pages, LIFO batch:7
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208
Kernel command line: root=mtd:rootfs rw rootfstype=jffs2 console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 512 (order: 9, 2048 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Memory: 123032k/129848k available (3945k kernel code, 6644k reserved, 992k data, 168k init, 0k highmem)
Calibrating delay loop... 398.33 BogoMIPS (lpj=199168)
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 Feb 23 2016 09:51:00
CPU revision is: 0002a080 (Broadcom4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
net_namespace: 1140 bytes
NET: Registered protocol family 16
Total Flash size: 0K with -1 sectors
Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (00008d6f-00008d79=-10<300)
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff]
pci 0000:00:00.0: supports D1 D2
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x007fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x11000000-0x110fffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
skbFreeTask created successfully
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Feb 23 2016 10:02:00 initialized
Broadcom GBPM v0.1 Feb 23 2016 10:02:01 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) c 2001-2006 Red Hat, Inc.
fuse init (API version 7.11)
msgmni has been set to 240
io scheduler noop registered (default)
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v2.0
Failed to read image tag from flash
Broadcom DSL NAND controller (BrcmNand Controller)
-->brcmnand_scan: CS=0, numchips=1, csi=0
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
Disabling XOR on CS#0
brcmnand_scan: Calling brcmnand_probe for CS=0
B4: NandSelect=40000001, nandConfig=16152300, chipSelect=0
brcmnand_read_id: CS0: dev_id=c2da9095
After: NandSelect=40000001, nandConfig=16152300
DevId c2da9095 may not be supported. Will use config info
Spare Area Size = 16B/512B
Block size=00020000, erase shift=17
NAND Config: Reg=16152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 6574845b
timing2 not adjusted: 00001e96
brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010
ECC level changed to 15
OOB size changed to 16
BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 256MB on CS0
Found NAND on CS0: ACC=f7ff1010, cfg=16152300, flashId=c2da9095, tim1=6574845b, tim2=00001e96
BrcmNAND version = 0x0400 256MB @00000000
brcmnand_scan: Done brcmnand_probe
brcmnand_scan: B4 nand_select = 40000001
brcmnand_scan: After nand_select = 40000001
100 CS=0, chip->ctrl->CS[0]=0
ECC level 15, threshold at 1 bits
reqEccLevel=0, eccLevel=15
190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010
brcmnand_scan 10
200 CS=0, chip->ctrl->CS[0]=0
200 chip->ecclevel=15, acc=f7ff1010
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
brcmnand_scan 220
Brcm NAND controller version = 4.0 NAND flash size 256MB @10000000
brcmnand_scan 230
brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000
brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
300 CS=0, chip->ctrl->CS[0]=0
500 chip=87ab9190, CS=0, chip->ctrl->CS[0]=0
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS0
brcmnand_scan 99
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
Total # RxBds=1448
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
bcmPktDma_init: Broadcom Packet DMA Library initialized
bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Feb 23 2016 10:01:03
p8021ag: p8021ag_init entry
IPSEC SPU: SUCCEEDED
GACT probability NOT on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2028 buckets, 8112 max)
GRE over IPv4 tunneling driver
nf_nat_pt: no ports specified
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_tcpmss registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03850600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:0388ba00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:0388ce00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9c000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9d000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03c19c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03c21800
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d35000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03e29c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04107c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04135800
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04169a00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04182000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:041a0600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:041a0600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04260000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:042e5400
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04302000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:0445dc00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:046c7600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:0492be00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:049efe00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04ac1e00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04b38a00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04b39a00
VFS: Mounted root (jffs2 filesystem) readonly on device 31:7.
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:057e8000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:058c3000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:059aee00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:05a25200
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:05af3400
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:05b32600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:05c02e00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:05c0da00
Freeing unused kernel memory: 168k freed
init started: BusyBox v1.15.3 ()
starting pid 261, tty '': '/etc/rcS'
jffs2_scan_dirent_node(): Node CRC failed on node at 0x00220fe4: Read 0xffffffff, calculated 0x0d19b389
Empty flash at 0x00221018 ends at 0x00221800
JFFS2 notice: (291) check_node_data: wrong data CRC in data node at 0x000c02cc: read 0xd0cf7ce8, calculated 0x7800a27f.
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d35000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d35000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04169a00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04135800
MCU module loaded ok v0.1 Feb 23 2016 09:57:56
bcm_ingqos: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Ingress QoS Module Char Driver v0.1 Feb 23 2016 09:57:53 Registered<243>
Broadcom Ingress QoS ver 0.1 initialized
BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128
Broadcom BPM Module Char Driver v0.1 Feb 23 2016 09:55:33 Registered<244>
[NTC bpm] bpm_set_status: BPM status : enabled
NBUFF v1.0 Initialized
Initialized fcache state
Broadcom Packet Flow Cache Char Driver v2.2 Feb 23 2016 09:57:55 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Feb 23 2016 09:57:55
chipId 0x631680D0
Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Feb 23 2016 09:57:42 Registered <241>
Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
FAP Debug values at 0xa5f9d300 0xa581d300
Allocated FAP0 GSO Buffers (0xA5FAE388) : 1048576 bytes @ 0xA5900000
Allocated FAP1 GSO Buffers (0xA582E388) : 1048576 bytes @ 0xA5A00000
Allocated FAP0 TM SDRAM Queue Storage (a5fae38c) : 341376 bytes @ a5880000
Allocated FAP1 TM SDRAM Queue Storage (a582e38c) : 341376 bytes @ a5b00000
[NTC fapProto] fapReset : Reset FAP Protocol layer
[FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3968>, free <2688>, total<8192>
[FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3968>, free <2688>, total<8192>
[FAP0] PSM : addr<0x80002000>, used <23436>, free <1140>, total <24576>
[FAP1] PSM : addr<0x80002000>, used <23436>, free <1140>, total <24576>
[FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948
[FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948
[FAP0] GSO Buffer set to 0xA5900000
[FAP1] GSO Buffer set to 0xA5A00000
[FAP0] FAP BPM Initialized.
[FAP1] FAP BPM Initialized.
fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes
fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes
bcmPktDma_bind: FAP Driver binding successfull
[FAP0] FAP TM: ON
[FAP1] FAP TM: ON
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM63168D0 Ethernet Network Device v0.1 Feb 23 2016 10:00:50
fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000
ETH Init: Ch:0 - 200 tx BDs at 0xb0820650
fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000
ETH Init: Ch:1 - 200 tx BDs at 0xb0a20650
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184
ETH Init: Ch:0 - 600 rx BDs at 0xb0821910
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184
ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: E0:60:66:79:75:5E
eth1: MAC Address: E0:60:66:79:75:5E
eth2: MAC Address: E0:60:66:79:75:5E
eth3: MAC Address: E0:60:66:79:75:5E
eth4: MAC Address: E0:60:66:79:75:5E
[NTC arl] arlEnable : Enabled ARL binding to FAP
Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Feb 23 2016 09:55:32 Registered <245>
Broadcom 802.1Q VLAN Interface, v0.1
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04107c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04107c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04107c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04107c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:04107c00
Endpoint: endpoint_init entry
Endpoint: endpoint_init COMPLETED
Success
Note: Loading 6300 MDK (default) driver for 63168 chip
Note: Forcing 53115 driver for 53125
Switch MDK: num_switches = 2
Switch MDK: unit = 0; phy_pbmp = 0x8; config_pbmp = 0x18
Switch MDK link poll thread: unit=0; phypbmp=0x8
Switch MDK link poll thread: unit=1; phypbmp=0x1e
VOX25_SERCOMM_VFES_3106
Tue Feb 23 10:48:14 UTC 2016
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d35000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d35000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d06600
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9d000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9c000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03ae0c00
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9d000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9c000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03d35000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9c000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9c000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9c000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9d000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9d000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03a9d000
brcmnand_ctrl_verify_ecc: Correctable ECC error at 00000000:03ae0c00
ap_name=syslogd, action=start
ap_name=coredump, action=start
ap_name=energy_saving, action=start
ap_name=dnrd, action=start
ap_name=phy, action=start
ap_name=dnsmasq, action=start
ap_name=lanip, action=start
ap_name=firewall, action=start
ap_name=telnetd, action=start
ap_name=sshd, action=start
ap_name=httpd, action=start
ap_name=redirect, action=start
ap_name=dnrd, action=start
bind: Address already in use
ap_name=ftpd, action=start
ap_name=networkmap, action=start
ap_name=srt, action=restart
ap_name=rp, action=start
ap_name=udpecho, action=start
ap_name=ntp, action=start
ap_name=wlan, action=start
ap_name=ingress_qos, action=start
ap_name=ingress_classify, action=start
ap_name=qos, action=start
ap_name=qos_cls, action=start
/bin/wlctl: Not Found
/bin/wlctl: Not Found
/bin/wlctl: Not Found
/bin/wlctl: Not Found
Setting SSID: "test"
Setting SSID: "_ONOWiFi"
Setting SSID: "_AUTO_ONOWiFi"
ifconfig: SIOCGIFFLAGS: No such device
Chanspec set to 0x1803
/bin/wlctl: Not In Range
/bin/wlctl: Not In Range
ifconfig: SIOCGIFFLAGS: No such device
Setting SSID: "test_5G"
Setting SSID: "_ONOWiFi"
Setting SSID: "_AUTO_ONOWiFi"
ifconfig: SIOCGIFFLAGS: No such device
Chanspec set to 0xe06a
/bin/wlctl: Not In Range
/bin/wlctl: Not In Range
ifconfig: SIOCGIFFLAGS: No such device
Success
Success
Success
ap_name=qos_remark, action=start
ACSD >>main(499): No interface specified, exiting...connect failed: Connection refused
connect failed: Connection refused
killall: wps_det: no process killed
ap_name=ipv6wd, action=start
ap_name=duplexmode, action=start
ap_name=cpm, action=start
ap_name=igd_upnp, action=start
ap_name=dnsr, action=start
ap_name=cron, action=start
ap_name=cups, action=start
ap_name=snmp, action=start
ap_name=3g, action=start
ap_name=emrd, action=start
ap_name=fon, action=start
starting pid 1560, tty '': '/sbin/getty ttyS0 115200'
VOX25 login: [/spoiler]