Instalado y funcionando perfecto en modo cliente (cliente-puente)
Todos los equipos de mi red se ven perfectamente entre ellos, estén 'detrás' o 'delante' del Comtrend
Lo he dejado (momentáneamente) sustituyendo a un WRT54GL. A ver cómo se porta
Hola
Pues ayer consegui que funcionara, pero toque y no ha vuelto a funcionar
Si eres tan amable RollerDK ¿podrias pegar aqui la configuracion de etc/config/network y etc/config/wireless?(borrando tu clave)
Y otro detalle, como pones las ips en pc/xbox fijas o automatico
Un saludo y gracias
Si te valen los míos ...
root@OpenWrt:~# cat /etc/config/network
config 'interface' 'loopback'
option 'ifname' 'lo'
option 'proto' 'static'
option 'ipaddr' '127.0.0.1'
option 'netmask' '255.0.0.0'
config 'interface' 'lan'
option 'type' 'bridge'
option 'ifname' 'eth1'
option 'proto' 'static'
option 'nat' '1'
option 'defaultroute' '0'
option 'peerdns' '0'
option 'ipaddr' '10.0.0.200'
option 'netmask' '255.0.0.0'
option 'gateway' '10.0.0.1'
config 'interface' 'wan'
option 'ifname' 'eth0'
option 'proto' 'dhcp'
root@OpenWrt:~# cat /etc/config/wireless
config 'wifi-device' 'wl0'
option 'type' 'broadcom'
option 'disabled' '0'
option 'channel' '10'
option 'txpower' '18'
option 'hwmode' '11gst'
config 'wifi-iface'
option 'device' 'wl0'
option 'network' 'lan'
option 'mode' 'sta'
option 'ssid' '**********'
option 'encryption' 'psk'
option 'key' '**********'
Ah, yo lo he puesto a 18db y en modo G+turbo (por probar).
No he podido probar aún si funciona en modo repetidor ... todo se andará
Excelente jar229
sERASEr, ya no te los pongo porque son muy similares a los de jar229. Si tienes problemas para conectar te hecho mano sin problema.
Lamenteblemente, al activar 2 señales de red, la tarjeta inalmabrica deja de responder y el router ya no reinicia. Por ahora, el modo repetidor no es posible pero bueno....a hacer pruebas toca!!!!
Un saludo.
EDITO: Como sabeis, el modo puente cliente solo es posible gracias al driver propietario de Broadcom, por esto:
http://wiki.openwrt.org/doc/recipes/bridgedclientEn si mismo, el openwrt no lo desarrollan para crear este tipo de configuración, de hecho acusan a ese driver de ser...como decirlo...una "chapuzada", que la unica transparencia solo se consigue con WDS. Cosas de los que entienden vamos....
En concreto sería esto:
Why it works on brcm-2.4
The propretary wl.o Broadcom wireless driver implements an ARP-NAT (Layer 2 address translation) mechanism called WET mode. ARP-NAT is comparable to Masquerading used on Layer 3 to connect multiple hosts using only one globally routed public IP address.However, the address translation used by the Broadcom driver
is not fully transparent and can cause various hard to debug network issues:
* A host on the AP side may not be able to reach a host on the Station side until the other side made an initial connection attempt
* Layer 3 routing on the Station side using a host behind the AP as gateway is unreliable or does not work at all
* The mapping entries in the ARP-NAT table may time out causing sudden connection loss
* The translation table may run out of space resulting in connection problems for some hosts on the Station side
Fuente:
http://wiki.openwrt.org/doc/howto/clientmode#bridged.client.mode.issuesSin embargo, yo llevo tiempo usandolo en el WRT54GL y no he tenido problema.