Hola he instalado una version que trae drivers para ralink 3070 y no me conecta la tarjeta de red ni me deja buscar redes.
La de post #733
Si sabes de otra version que funcione lo agradeceria.
He puesto "wifi detect > /etc/config/wireless". Para que se añada.
Dejo el log.
[ 0.000000] Linux version 3.8.12 (marco@homer) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36574) ) #6 Mon May 13 22:26:08 CEST 2013
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 100.48.56-48.46
[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 33303138, got 0c0ed182)
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: HW553
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802e0540, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 61428k/65536k available (2364k kernel code, 4108k reserved, 597k data, 236k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.064000] registering PCI controller with io_map_base unset
[ 0.084000] bio: create slab <bio-0> at 0
[ 0.092000] PCI host bridge to bus 0000:00
[ 0.096000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.100000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.104000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.108000] pci 0000:00:01.0: [14e4:4318] type 00 class 0x028000
[ 0.108000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00001fff]
[ 0.120000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.120000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff]
[ 0.124000] Switching to clocksource MIPS
[ 0.136000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 0.144000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
[ 0.164000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x00
[ 0.172000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
[ 0.172000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
[ 0.172000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[ 0.172000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[ 0.212000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.220000] NET: Registered protocol family 2
[ 0.228000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.232000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.240000] TCP: Hash tables configured (established 512 bind 512)
[ 0.248000] TCP: reno registered
[ 0.252000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.256000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.264000] NET: Registered protocol family 1
[ 0.268000] PCI: CLS 0 bytes, default 16
[ 0.272000] audit: initializing netlink socket (disabled)
[ 0.280000] type=2000 audit(0.279:1): initialized
[ 0.284000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.292000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.300000] msgmni has been set to 119
[ 0.308000] io scheduler noop registered
[ 0.312000] io scheduler deadline registered (default)
[ 0.316000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.324000] console [ttyS0] enabled, bootconsole disabled
[ 0.344000] physmap platform flash device: 02000000 at 1e000000
[ 0.348000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 0.360000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.360000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.364000] Amd/Fujitsu Extended Query version 1.3.
[ 0.372000] number of CFI chips: 1
[ 0.376000] bcm63xxpart: CFE boot tag found with version 7 and board type HW553
[ 0.380000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.388000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[ 0.396000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length ea0000
[ 0.404000] bcm63xxpart: Partition 3 is nvram offset fe0000 and length 20000
[ 0.412000] bcm63xxpart: Partition 4 is linux offset 20000 and length fc0000
[ 0.416000] bcm63xxpart: Spare partition is offset f60004 and length 7fffc
[ 0.424000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.432000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.436000] 0x000000000000-0x000000020000 : "CFE"
[ 0.448000] 0x000000020100-0x000000140000 : "kernel"
[ 0.452000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.468000] 0x000000140000-0x000000fe0000 : "rootfs"
[ 0.476000] mtd: partition "rootfs" set to be root filesystem
[ 0.484000] mtd: partition "rootfs_data" created automatically, ofs=F60000, len=80000
[ 0.492000] 0x000000f60000-0x000000fe0000 : "rootfs_data"
[ 0.500000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.508000] 0x000000020000-0x000000fe0000 : "linux"
[ 0.520000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[ 0.540000] libphy: bcm63xx_enet MII bus: probed
[ 0.544000] bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Generic PHY]
[ 0.556000] libphy: bcm63xx_enet MII bus: probed
[ 0.564000] b53_common: found switch: BCM5325, rev 0
[ 0.568000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[ 0.584000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.600000] TCP: cubic registered
[ 0.600000] NET: Registered protocol family 17
[ 0.608000] 8021q: 802.1Q VLAN Support v1.8
[ 0.620000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.632000] Freeing unused kernel memory: 236k freed
[ 13.900000] compat-drivers backport release: compat-drivers-2013-03-28-5
[ 13.904000] Backport based on wireless-testing.git master-2013-04-16
[ 13.912000] compat.git: wireless-testing.git
[ 14.152000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.156000] cfg80211: World regulatory domain updated:
[ 14.164000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.172000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.180000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.188000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.196000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.204000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.880000] SCSI subsystem initialized
[ 16.180000] usbcore: registered new interface driver usbfs
[ 16.184000] usbcore: registered new interface driver hub
[ 16.192000] usbcore: registered new device driver usb
[ 17.908000] usbcore: registered new interface driver rt73usb
[ 17.964000] usbcore: registered new interface driver rtl8187
[ 18.016000] usbcore: registered new interface driver rt2800usb
[ 19.620000] wl: module license 'unspecified' taints kernel.
[ 19.624000] Disabling lock debugging due to kernel taint
[ 19.752000] SSB/BCMA glue driver successfully attached
[ 19.772000] Got version 2 SPROM from SSB
[ 19.784000] wl0: Broadcom BCM4318 802.11 Wireless Controller 5.10.56.27
[ 19.944000] Button Hotplug driver version 0.4.1
[ 21.692000] PPP generic driver version 2.4.2
[ 21.780000] tun: Universal TUN/TAP device driver, 1.6
[ 21.788000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 21.836000] usbcore: registered new interface driver p54usb
[ 22.300000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 22.960000] NET: Registered protocol family 24
[ 23.364000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 23.408000] ehci-platform: EHCI generic platform driver
[ 23.416000] ehci-platform ehci-platform: EHCI Host Controller
[ 23.420000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 23.428000] ehci-platform ehci-platform: irq 18, io mem 0xfffe1300
[ 23.448000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 23.456000] hub 1-0:1.0: USB hub found
[ 23.460000] hub 1-0:1.0: 2 ports detected
[ 23.676000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[ 24.044000] usb 1-2: new high-speed USB device number 2 using ehci-platform
[ 24.500000] usb 1-2: reset high-speed USB device number 2 using ehci-platform
[ 25.060000] phy0 -> rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 25.248000] phy0 -> rt2x00_set_rf: Info - RF chipset 0005 detected
[ 25.256000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 25.716000] xt_time: kernel timezone is -0000
[ 26.596000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 26.600000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 26.608000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 26.616000] ohci-platform ohci-platform: irq 13, io mem 0xfffe1400
[ 26.684000] hub 2-0:1.0: USB hub found
[ 26.688000] hub 2-0:1.0: 1 port detected
[ 26.892000] uhci_hcd: USB Universal Host Controller Interface driver
[ 27.080000] usbcore: registered new interface driver ath9k_htc
[ 27.456000] usbcore: registered new interface driver usblp
[ 27.512000] usbcore: registered new interface driver usbserial
[ 27.516000] usbcore: registered new interface driver usbserial_generic
[ 27.524000] usbserial: USB Serial support registered for generic
[ 27.760000] Initializing USB Mass Storage driver...
[ 27.768000] usbcore: registered new interface driver usb-storage
[ 27.772000] USB Mass Storage support registered.
[ 28.808000] u32 classifier
[ 28.808000] Performance counters on
[ 28.812000] input device check on
[ 28.816000] Actions configured
[ 29.004000] Mirror/redirect action on
[ 29.260000] usbcore: registered new interface driver usbhid
[ 29.264000] usbhid: USB HID core driver
[ 29.676000] fuse init (API version 7.20)
[ 42.176000] device eth1 entered promiscuous mode
[ 43.712000] eth1: link UP - 100/full - flow control off
[ 43.716000] br-lan: port 1(eth1) entered forwarding state
[ 43.720000] br-lan: port 1(eth1) entered forwarding state
[ 45.724000] br-lan: port 1(eth1) entered forwarding state
[ 78.444000] device br-lan entered promiscuous mode
[ 78.532000] device br-lan left promiscuous mode
[ 92.700000] jffs2: Too few erase blocks (4)
[ 124.436000] usb 1-2: USB disconnect, device number 2
[ 126.252000] usb 1-2: new high-speed USB device number 3 using ehci-platform
[ 126.532000] usb 1-2: reset high-speed USB device number 3 using ehci-platform
[ 126.684000] phy1 -> rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 126.724000] phy1 -> rt2x00_set_rf: Info - RF chipset 0005 detected
[ 126.732000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Gracias y un saludo