Equipos y materiales > Openwrt & LEDE
[Solucionado] Ayuda con WDR3600 brickeado
(1/1)
zapple:
Hola compañeros.
Tengo por aqui un TPLink TL-WDR3600 ver1.5 aparentemente muerto.
Al darle al boton de encendido se encienden por un momento todos los leds pero solo se queda encendido el led de "power" y no responde a nada.
Estoy siguiendo este post de SinHouse https://foro.seguridadwireless.net/openwrt/router-tp-link-wdr3600-brickeado-tras-instalar-openwrt/msg318687/#msg318687 pero estoy teniendo problemas...
Siguiendo las instrucciones del post de SinHouse, al encender el router, configurando el software TeraTerm como 115200 8 N 1 N, me salen una serie de caracteres extraños al principio, despues ya sale algo legible y se para... hago copy/paste:
--- Código: ---ŠC¡UI½½ÑDB12jùŠ8 &Šªj 19'SÒ¢’)
ŠC!”5é Š28 S¨Høid òYX‚ÂÅ0°‚‚2™
f+Í¡sizeÂMB¬š•Ñor ¬«¹Ñ= 1&j
ŠÐ¨ªReseôz-…!!!!HC¡ÊKš•É¥…l Æ+Í¡é 8 S¨HøUsZëäYVÕ±t eîWK½¹menWH
ªÑé så®+±5
Erò'š•É¥…±
Net'
934}•¹•Ñ_inZW+±¥ze®É©
ê
²…±id XÉ•Ís é
2±…sh. U®ËëfiøY
‘dre®®Hø ÷X. resåj…Ík:cš30°j
WÁ*jj--¾šÅ7!e*
: cfV‚Â] cf–‚Â]11´Cáe
Ò…ébY'Véce:°Ò¢Šj
Šetè‚upC¡–¡A aKÍÅ7_reÖ•¹¥t: ã«Á±•te
Autï¬ë‹¥ng Z
Š#£½½Ñing Z[ØV•½¹ds
Ñ9f0²‚‚‚ò..!ª¹½µpreó®ËëKerîY
Jµager.. OËC¡HhE…ÉÑ¥ng –¹•l .®©
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc version 4.3.3 (GCC) ) #1 Mon Mar 2 19:22:36 CST 2015
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6848k(rootfs),128k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112896k/131072k available (1856k kernel code, 17996k reserved, 432k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000]
[ 0.096000] ****************ALLOC***********************
[ 0.096000] Packet mem: 8026e4c0 (0xe00000 bytes)
[ 0.096000] ********************************************
[ 0.096000]
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] PCI init:ath_pcibios_init
[ 0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[ 0.096000] registering PCI controller with io_map_base unset
[ 0.096000] bio: create slab <bio-0> at 0
[ 0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.096000] pci 0000:00:00.0: PME# disabled
[ 0.096000] Returning IRQ 64
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.100000] TCP reno registered
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] ATH GPIOC major 0
[ 0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.100000] msgmni has been set to 220
[ 0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.100000] io scheduler noop registered
[ 0.100000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.104000] console [ttyS0] enabled
[ 0.404000] PPP generic driver version 2.4.2
[ 0.408000] NET: Registered protocol family 24
[ 0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.416000] Creating 5 MTD partitions on "ath-nor0":
[ 0.424000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.428000] 0x000000020000-0x000000120000 : "kernel"
[ 0.432000] 0x000000120000-0x0000007d0000 : "rootfs"
[ 0.440000] 0x0000007d0000-0x0000007f0000 : "config"
[ 0.444000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.448000] ->Oops: flash id 0xef4017 .
[ 0.452000] ----TP IGMP has been init------
[ 0.456000] TCP cubic registered
[ 0.460000] NET: Registered protocol family 10
[ 0.468000] NET: Registered protocol family 17
[ 0.472000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.476000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.484000] athwdt_init: Registering WDT success
[ 0.488000] ath_otp_init: Registering OTP success
[ 0.492000] ath_clksw_init: Registering Clock Switch Interface success
[ 0.504000] SQUASHFS error: squashfs_read_data failed to read block 0x53b76a
[ 0.512000] SQUASHFS error: Unable to read metadata cache entry [53b76a]
[ 0.516000] SQUASHFS error: Unable to read inode 0xfea18c5
[ 0.524000] ------------[ cut here ]------------
[ 0.528000] WARNING: at fs/inode.c:707 unlock_new_inode+0x30/0x58()
[ 0.532000] Modules linked in:
[ 0.536000] Call Trace:
[ 0.540000] [<801cf68c>] dump_stack+0x8/0x34
[ 0.544000] [<800242ac>] warn_slowpath_common+0x70/0xb0
[ 0.548000] [<800831f4>] unlock_new_inode+0x30/0x58
[ 0.552000] [<80085350>] iget_failed+0x1c/0x3c
[ 0.560000] [<800bd674>] squashfs_fill_super+0x620/0x724
[ 0.564000] [<800727e4>] get_sb_bdev+0x11c/0x194
[ 0.568000] [<800bcf90>] squashfs_get_sb+0x20/0x2c
[ 0.572000] [<800716b4>] vfs_kern_mount+0x68/0xd0
[ 0.580000] [<80071780>] do_kern_mount+0x54/0x118
[ 0.584000] [<8008917c>] do_mount+0x690/0x71c
[ 0.588000] [<8008929c>] sys_mount+0x94/0x158
[ 0.592000] [<8023fc60>] mount_block_root+0x13c/0x2fc
[ 0.596000] [<8024005c>] prepare_namespace+0x1c0/0x1f4
[ 0.604000] [<8023f350>] kernel_init+0xe4/0x104
[ 0.608000] [<800089f8>] kernel_thread_helper+0x10/0x18
[ 0.612000]
[ 0.612000] ---[ end trace bab6d9a119dbbd4e ]---
[ 0.620000] VFS: Cannot open root device "31:02" or unknown-block(31,2)
[ 0.624000] Please append a correct "root=" boot option; here are the available partitions:
[ 0.636000] 1f00 128 mtdblock0 (driver?)
[ 0.640000] 1f01 1024 mtdblock1 (driver?)
[ 0.644000] 1f02 6848 mtdblock2 (driver?)
[ 0.648000] 1f03 128 mtdblock3 (driver?)
[ 0.656000] 1f04 64 mtdblock4 (driver?)
[ 0.660000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
--- Fin del código ---
He comprobado que configurando Teraterm como 115200 7 N 1 N ya no salen los caracteres extraños y se para en el mismo sitio. Hago copy/paste:
--- Código: ---U-Boot 1.1.4 (May 18 2015 - 19:45:42)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc version 4.3.3 (GCC) ) #1 Mon Mar 2 19:22:36 CST 2015
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6848k(rootfs),128k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112896k/131072k available (1856k kernel code, 17996k reserved, 432k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000]
[ 0.096000] ****************ALLOC***********************
[ 0.096000] Packet mem: 8026e4c0 (0xe00000 bytes)
[ 0.096000] ********************************************
[ 0.096000]
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] PCI init:ath_pcibios_init
[ 0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[ 0.096000] registering PCI controller with io_map_base unset
[ 0.096000] bio: create slab <bio-0> at 0
[ 0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.096000] pci 0000:00:00.0: PME# disabled
[ 0.096000] Returning IRQ 64
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.100000] TCP reno registered
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] ATH GPIOC major 0
[ 0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.100000] msgmni has been set to 220
[ 0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.100000] io scheduler noop registered
[ 0.100000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.104000] console [ttyS0] enabled
[ 0.404000] PPP generic driver version 2.4.2
[ 0.408000] NET: Registered protocol family 24
[ 0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.416000] Creating 5 MTD partitions on "ath-nor0":
[ 0.424000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.428000] 0x000000020000-0x000000120000 : "kernel"
[ 0.432000] 0x000000120000-0x0000007d0000 : "rootfs"
[ 0.440000] 0x0000007d0000-0x0000007f0000 : "config"
[ 0.444000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.448000] ->Oops: flash id 0xef4017 .
[ 0.452000] ----TP IGMP has been init------
[ 0.456000] TCP cubic registered
[ 0.460000] NET: Registered protocol family 10
[ 0.468000] NET: Registered protocol family 17
[ 0.472000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.476000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.484000] athwdt_init: Registering WDT success
[ 0.488000] ath_otp_init: Registering OTP success
[ 0.492000] ath_clksw_init: Registering Clock Switch Interface success
[ 0.504000] SQUASHFS error: squashfs_read_data failed to read block 0x53b76a
[ 0.512000] SQUASHFS error: Unable to read metadata cache entry [53b76a]
[ 0.516000] SQUASHFS error: Unable to read inode 0xfea18c5
[ 0.524000] ------------[ cut here ]------------
[ 0.528000] WARNING: at fs/inode.c:707 unlock_new_inode+0x30/0x58()
[ 0.532000] Modules linked in:
[ 0.536000] Call Trace:
[ 0.540000] [<801cf68c>] dump_stack+0x8/0x34
[ 0.544000] [<800242ac>] warn_slowpath_common+0x70/0xb0
[ 0.548000] [<800831f4>] unlock_new_inode+0x30/0x58
[ 0.552000] [<80085350>] iget_failed+0x1c/0x3c
[ 0.560000] [<800bd674>] squashfs_fill_super+0x620/0x724
[ 0.564000] [<800727e4>] get_sb_bdev+0x11c/0x194
[ 0.568000] [<800bcf90>] squashfs_get_sb+0x20/0x2c
[ 0.572000] [<800716b4>] vfs_kern_mount+0x68/0xd0
[ 0.580000] [<80071780>] do_kern_mount+0x54/0x118
[ 0.584000] [<8008917c>] do_mount+0x690/0x71c
[ 0.588000] [<8008929c>] sys_mount+0x94/0x158
[ 0.592000] [<8023fc60>] mount_block_root+0x13c/0x2fc
[ 0.596000] [<8024005c>] prepare_namespace+0x1c0/0x1f4
[ 0.604000] [<8023f350>] kernel_init+0xe4/0x104
[ 0.608000] [<800089f8>] kernel_thread_helper+0x10/0x18
[ 0.612000]
[ 0.612000] ---[ end trace bab6d9a119dbbd4e ]---
[ 0.620000] VFS: Cannot open root device "31:02" or unknown-block(31,2)
[ 0.624000] Please append a correct "root=" boot option; here are the available partitions:
[ 0.636000] 1f00 128 mtdblock0 (driver?)
[ 0.640000] 1f01 1024 mtdblock1 (driver?)
[ 0.644000] 1f02 6848 mtdblock2 (driver?)
[ 0.648000] 1f03 128 mtdblock3 (driver?)
[ 0.656000] 1f04 64 mtdblock4 (driver?)
[ 0.660000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
--- Fin del código ---
El caso es que he intentado varias veces a teclear "tpl" tras "Autobooting in 1 seconds" pero no logro la manera de que envie el firmware.
Estoy usando este usb a serie ttl http://www.ebay.es/itm/1x-Modulo-CH340G-adaptador-USB-a-serie-TTL-RS232-USB-TO-SERIAL-REPLACE-PL2303/131564268806?hash=item1ea1d76d06:g:8BgAAOSwd0BVtAFl
Me llama la atención que cambiando el Data de 8 a 7 bits permita leer los caracteres correctos y por esto estoy dudando a ver si el problema es a causa de este adaptador ttl que tengo.
Os ha pasado alguna vez? Se os ocurre algo??
se agradece, un abrazo!
zapple:
Hola de nuevo compañeros.
Ya he podido recuperar el WDR3600 ver1.5, solo que a través de otro metodo, que aunque ya lo habia leido por ahi y probado repetidas veces, nunca logré que funcionase... http://www.theoutpost.org/6-techy/tp-link-wdr3600-recovery-without-serial/
... la diferencia de que ahora me haya funcionado es que he utilizado el USB-TTL para monitorizar el proceso y esto me ha ayudado a descubrir los errores para enmendarlos.
El metodo dice más o menos que encendiendo el WDR3600 mientras se mantiene pulsado el boton "Reset/WPS" durante aproximadamente 7 segundos, el WDR3600 nos pedirá un firmware con el nombre "wdr3600v1_tp_recovery.bin".
Teniendo conectado el USB-TTL y curiosamente en mi caso y como os comentaba en el post anterior, lo tengo configurado a 115200 7 N 1, me aparece lo siguiente:
--- Código: ---U-Boot 1.1.4 (May 18 2015 - 19:45:42)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wdr3600v1_tp_recovery.bin'.
--- Fin del código ---
Subo aqui el archivo 'wdr3600v1_tp_recovery.bin' por el que está preguntando el router:
https://www.mediafire.com/file/omss46zk6mkq0a1/wdr3600v1_tp_recovery.bin
Pues nada, a partir de esta información todo ha sido muy sencillo.
-Cambio la IP de la tarjeta ethernet del ordenador y pongo esta IP fija:
IPv4: 192.168.0.66
Netmask: 255.255.255.0
-Arranco un programa TFTP, le indico esta IP y donde se encuentra el archivo del firmware 'wdr3600v1_tp_recovery.bin'.
-Enciendo el router manteniendo pulsado el boton "Reset/WPS" durante aproximadamente 7 segundos.
.... y mira por donde, ya se traga el firmware.
--- Código: ---U-Boot 1.1.4 (May 18 2015 - 19:45:42)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wdr3600v1_tp_recovery.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################
done
Bytes transferred = 8192512 (7d0200 hex)
original_product_id = 36000001
original_product_ver = 01
recovery_product_id = 36000001
recovery_product_ver = 01
auto update firmware: product id verify sucess!
Firmware recovery: product id verify sucess!
Firmware recovery: filesize = 0x7d0200.
boot up image
First 0x2 last 0x7c sector size 0x10000
124
Erased 123 sectors
Copy to Flash... write addr: 9f020000
done
U-Boot 1.1.4 (May 18 2015 - 19:45:42)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting Atheros AR934x
[ 0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@liaozhiming) (gcc version 4.3.3 (GCC) ) #1 Mon May 18 19:48:32 CST 2015
[ 0.000000] Ram size passed from bootloader =128M
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6848k(rootfs),128k(config),64k(ART) mem=128M
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 112896k/131072k available (1856k kernel code, 17996k reserved, 432k data, 120k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[ 0.096000] Mount-cache hash table entries: 512
[ 0.096000]
[ 0.096000] ****************ALLOC***********************
[ 0.096000] Packet mem: 8026e4c0 (0xe00000 bytes)
[ 0.096000] ********************************************
[ 0.096000]
[ 0.096000] NET: Registered protocol family 16
[ 0.096000] PCI init:ath_pcibios_init
[ 0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[ 0.096000] registering PCI controller with io_map_base unset
[ 0.096000] bio: create slab <bio-0> at 0
[ 0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.096000] pci 0000:00:00.0: PME# disabled
[ 0.096000] Returning IRQ 64
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] TCP established hash table entries: 4096 (order:32768 bytes)
[ 0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.100000] TCP reno registered
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] ATH GPIOC major 0
[ 0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.100000] msgmni has been set to 220
[ 0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.100000] io scheduler noop registered
[ 0.100000] io scheduler deadline registered (default)
[ 0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.104000] console [ttyS0] enabled
[ 0.404000] PPP generic driver version 2.4.2
[ 0.408000] NET: Registered protocol family 24
[ 0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[ 0.416000] Creating 5 MTD partitions on "ath-nor0":
[ 0.424000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.428000] 0x000000020000-0x000000120000 : "kernel"
[ 0.432000] 0x000000120000-0x0000007d0000 : "rootfs"
[ 0.440000] 0x0000007d0000-0x0000007f0000 : "config"
[ 0.444000] 0x0000007f0000-0x000000800000 : "ART"
[ 0.448000] ->Oops: flash id 0xef4017 .
[ 0.452000] ----TP IGMP has been init------
[ 0.456000] TCP cubic registered
[ 0.460000] NET: Registered protocol family 10
[ 0.468000] NET: Registered protocol family 17
[ 0.472000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.476000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.484000] athwdt_init: Registering WDT success
[ 0.488000] ath_otp_init: Registering OTP success
[ 0.492000] ath_clksw_init: Registering Clock Switch Interface success
[ 0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.516000] Freeing unused kernel memory: 120k freed
init started: BusyBox v1.01 (2015.04.24-06:01+0000) multi-call binary
This Board use 2.6.31
insmod: cannot open module `/lib/modules/2.6.31/kernel/x_tables.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_tcpudp.ko': No such file or directory
[ 1.688000] xt_time: kernel timezone is -0000
[ 1.884000] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 1.888000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 1.896000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 1.904000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[ 2.736000] PPPoL2TP kernel driver, V1.0
[ 2.756000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
(none) mips #1 Mon May 18 19:48:32 CST 2015 (none)
(none) login: [ 6.992000] Now flash open!
[ 6.996000] Read from 0X20000 to 0X20120: OK
[ 7.524000] Now flash open!
[ 7.528000] Read from 0X7D0000 to 0X7E1F0C: OK
[ 7.556000] Now flash open!
[ 7.560000] Read from 0X1FC00 to 0X1FC06: OK
[ 7.664000] Now flash open!
[ 7.664000] Read from 0X1FE00 to 0X1FE08: OK
[ 7.772000] Now flash open!
[ 7.772000] Erase from 0X7D0000 to 0X7E1F0C:.
[ 7.968000] Program from 0X7D0000 to 0X7E1F0C:.
[ 8.336000] write successfully
[ 8.344000] Now flash open!
[ 8.344000] Read from 0X1FE00 to 0X1FE08: OK
[ 8.348000] Now flash open!
[ 8.352000] Erase from 0X7D0000 to 0X7E1F0C:.
[ 8.556000] Program from 0X7D0000 to 0X7E1F0C:.
[ 8.908000] write successfully
[ 8.912000] Now flash open!
[ 8.916000] Erase from 0X7D0000 to 0X7E1F0C:.
[ 9.112000] Program from 0X7D0000 to 0X7E1F0C:.
[ 9.472000] write successfully
[ 9.808000] ATHR_GMAC: Length per segment 1536
[ 9.812000] ATHR_GMAC: fifo cfg 3 01f00140
[ 9.816000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[ 9.820000] ATHR_GMAC: Mac address for unit 0:bfff0000
[ 9.824000] ATHR_GMAC: ff:ff:ff:ff:ff:ff
[ 10.380000] ATHR_GMAC: Max segments per packet : 1
[ 10.384000] ATHR_GMAC: Max tx descriptor count : 128
[ 10.388000] ATHR_GMAC: Max rx descriptor count : 128
[ 10.396000] ATHR_GMAC: Mac capability flags : 2381
[ 10.428000] athr_gmac_ring_alloc Allocated 2048 at 0x87b12000
[ 10.436000] athr_gmac_ring_alloc Allocated 2048 at 0x87b10800
[ 10.740000] WASP ----> S17 PHY *
[ 10.744000] Setting Drop CRC Errors, Pause Frames and Length Error frames
[ 10.816000] Hello, nat module!
[ 10.820000] thread: napt_ct_scan create success pid:118
[ 10.824000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[ 10.832000] isis_ip_intf_entry_add id[0] for vid[1]
[ 10.840000] isis_ip_intf_entry_add id[1] for vid[2]
[ 10.844000]
[ 10.844000] ######## S17 SSDK init succeeded! ########
[ 10.864000] ++++ athrs17_igmp_setup once
[ 10.892000] athrs17_reg_init:done
[ 10.896000] Setting PHY...
[ 11.900000] napt_ct_scan_thread: time: 4
[ 11.908000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.952000] device eth0.1 entered promiscuous mode
[ 11.964000] Now flash open!
[ 11.968000] Read from 0X1FC00 to 0X1FC06: OK
[ 11.976000] isis_ip_intf_entry_add id[0] for vid[1]
[ 11.980000] Lan UDP checksum 0 adding rule #3
[ 12.012000] ACL is not yet enabled. Enabling...
[ 12.020000] isis_ip_intf_entry_add id[1] for vid[2]
[ 12.024000] Wan UDP checksum 0 adding rule #2
[ 12.044000] ttl adding rule #0
[ 12.084000] device eth0 entered promiscuous mode
[ 12.144000] br0: port 1(eth0.1) entering forwarding state
[ 13.716000] Adding ACL rules 1 - wan to lan, dst ip is lan net
[ 14.320000] nf_conntrack_rtsp v0.6.21 loading
[ 14.340000] nf_nat_rtsp v0.6.21 loading
[ 14.388000] insmod nat_sip over !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[ 14.400000]
[ 14.400000] Enet:0 port1 up
[ 14.404000] ATH_MAC_TIMER: enet unit:0 is up...
[ 14.408000] RGMii 1000Mbps full duplex
[ 14.412000] ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl
[ 14.420000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
usrconf_allocate_memory 212 shmget success id:43511 32769
[ 14.716000] asf: module license 'Proprietary' taints kernel.
[ 14.724000] Disabling lock debugging due to kernel taint
[ 15.292000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
[ 15.412000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 15.444000] ath_dfs: Version 2.0.0
[ 15.444000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[ 15.644000] Now flash open!
[ 15.644000] Read from 0X20000 to 0X20120: OK
[ 15.796000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 16.576000] ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 16.580000] __ath_attach: Set global_scn[0]
[ 16.584000] ACBKMinfree = 48
[ 16.588000] ACBEMinfree = 32
[ 16.592000] ACVIMinfree = 16
[ 16.592000] ACVOMinfree = 0
[ 16.596000] CABMinfree = 48
[ 16.600000] UAPSDMinfree = 0
[ 16.612000] Restoring Cal data from Flash
[ 16.616000] dfs_attach: use DFS enhancements
[ 16.624000] DFS min filter rssiThresh = 18
[ 16.628000] DFS max pulse dur = 151 ticks
[ 16.636000] ath_get_caps[5108] rx chainmask mismatch actual 3 sc_chainmak 0
[ 16.644000] ath_get_caps[5083] tx chainmask mismatch actual 3 sc_chainmak 0
[ 16.656000] SC Callback Registration for wifi0
[ 16.660000] wifi0: Atheros 9340: mem=0xb8100000, irq=2
[ 16.668000] ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
[ 16.672000] __ath_attach: Set global_scn[1]
[ 16.676000] ACBKMinfree = 48
[ 16.680000] ACBEMinfree = 32
[ 16.684000] ACVIMinfree = 16
[ 16.684000] ACVOMinfree = 0
[ 16.688000] CABMinfree = 48
[ 16.692000] UAPSDMinfree = 0
[ 16.700000] Restoring Cal data from Flash
[ 16.708000] dfs_attach: use DFS enhancements
[ 16.716000] DFS min filter rssiThresh = 18
[ 16.720000] DFS max pulse dur = 151 ticks
[ 16.724000] ath_get_caps[5108] rx chainmask mismatch actual 3 sc_chainmak 0
[ 16.732000] ath_get_caps[5083] tx chainmask mismatch actual 3 sc_chainmak 0
[ 16.748000] SC Callback Registration for wifi1
[ 16.752000] wifi1: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
[ 16.976000] wlan_vap_create : enter. devhandle=0x87bd82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 16.988000] wlan_vap_create : exit. devhandle=0x87bd82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 16.996000] VAP device ath0 created
[ 17.160000]
[ 17.160000] DES SSID SET=TP-LINK_2.4GHz_D53C04
[ 17.172000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
[ 23.140000] device ath0 entered promiscuous mode
[ 23.144000] br0: port 2(ath0) entering forwarding state
[ 23.756000] ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
[ 23.772000] br0: port 2(ath0) entering disabled state
[ 23.976000]
[ 23.976000] DES SSID SET=TP-LINK_2.4GHz_D53C04
[ 24.008000] br0: port 2(ath0) entering forwarding state
[ 25.896000] br0: port 2(ath0) entering disabled state
[ 25.956000] br0: starting userspace STP failed, starting kernel STP
[ 25.992000] br0: topology change detected, propagating
[ 25.996000] br0: port 2(ath0) entering forwarding state
[ 26.048000] wlan_vap_create : enter. devhandle=0x86c942c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 26.056000] wlan_vap_create : exit. devhandle=0x86c942c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 26.064000] VAP device ath1 created
[ 26.188000]
[ 26.188000] DES SSID SET=TP-LINK_5GHz_D53C05
[ 26.204000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
[ 30.612000] Found best 11na chan: 44
[ 32.084000] br0: port 1(eth0.1) entering disabled state
[ 32.108000] br0: topology change detected, propagating
[ 32.112000] br0: port 1(eth0.1) entering forwarding state
[ 32.136000] device ath1 entered promiscuous mode
[ 32.140000] br0: topology change detected, propagating
[ 32.148000] br0: port 3(ath1) entering forwarding state
[ 32.184000] ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, valid=1
[ 32.192000] br0: port 3(ath1) entering disabled state
[ 32.404000]
[ 32.404000] DES SSID SET=TP-LINK_5GHz_D53C05
[ 32.428000] br0: topology change detected, propagating
[ 32.432000] br0: port 3(ath1) entering forwarding state
[ 34.204000] br0: port 3(ath1) entering disabled state
[ 34.264000] br0: topology change detected, propagating
[ 34.268000] br0: port 3(ath1) entering forwarding state
[ 34.720000] fuse init (API version 7.12)
[ 34.928000] usbcore: registered new interface driver usbfs
[ 34.932000] usbcore: registered new interface driver hub
[ 34.940000] usbcore: registered new device driver usb
[ 34.972000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 35.020000] Port Status 1c000004
[ 35.020000] ath-ehci ath-ehci.0: ATH EHCI
[ 35.024000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[ 35.036000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 35.040000] ehci_reset Port Status 1c000000
[ 35.044000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[ 35.052000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 35.060000] ehci_reset Port Status 1c000000
[ 35.076000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[ 35.080000] usb usb1: configuration #1 chosen from 1 choice
[ 35.088000] hub 1-0:1.0: USB hub found
[ 35.092000] hub 1-0:1.0: 1 port detected
[ 35.312000] SCSI subsystem initialized
[ 35.444000] usb 1-1: new high speed USB device using ath-ehci and address 2
[ 35.592000] usb 1-1: configuration #1 chosen from 1 choice
[ 35.596000] hub 1-1:1.0: USB hub found
[ 35.600000] hub 1-1:1.0: 4 ports detected
[ 35.660000] Initializing USB Mass Storage driver...
[ 35.664000] usbcore: registered new interface driver usb-storage
[ 35.672000] USB Mass Storage support registered.
[ 37.408000] kcg 333 :GPL NetUSB up!
[ 37.644000] kc 90 : run_telnetDBGDServer start
[ 37.652000] kc 227 : init_DebugD end
[ 37.652000] INFO17ED: NetUSB 1.02.66, 0002061F : Apr 22 2015 18:23:53
[ 37.660000] INFO17EF: 7437: TL-WDR3600 v1 :TL-WDR3600 v1
[ 37.668000] INFO17F0: AUTH ISOC
[ 37.668000] INFO17F1: filterAudio
[ 37.672000] usbcore: registered new interface driver KC NetUSB General Driver
[ 37.684000] INFO0145: init proc : PAGE_SIZE 4096
[ 37.688000] INFO16E1: infomap 8658bf00
[ 37.692000] INFO16E4: sleep to wait br0 to wake up
[ 37.696000] INFO15B4: tcpConnector() started... : br0
[ 37.712000] TP_RULE_NAT:enable hardware nat
[ 37.764000] IPv6 over IPv4 tunneling driver
[ 40.276000] (tp_mroute_enable_write)173, tp_mroute_enable = 1
[ 40.300000] br0: port 2(ath0) entering disabled state
[ 40.400000] br0: port 3(ath1) entering disabled state
[ 40.728000] INFO1567: Bind to br0
check success
--- Fin del código ---
Añadir que al principio del proceso me sucedió una pequeña jodienda..... en un momento dado del proceso aparecía algo similar a esto:
--- Código: ---"Loading: T T T T (...) Retry count exceeded".
--- Fin del código ---
La solución la pude encontrar en un comentario que un usuario habia dejado debajo de este video de youtube:
--- Citar ---worked great many thanks ! this saved my router :) the additional step I had to add in my case was to manually change the NIC duplex settings from auto negotiation to 100 Full Duplex. I came upon this solution because when Uboot tried loading the image file I would get a "Loading: T T T T T T T T T T (...) Retry count exceeded; starting again" error. after making the changes to my NIC it worked great.
--- Fin de la cita ---
Es decir que si os sucede esto la solución es cambiar manualmente la configuración del hardware de la ethernet, de Autonegotiation a 100 Full Duplex.
En mi caso que uso un Macbook Pro (MacOS 10.13.1) como me ha funcionado es dejando el hardware ethernet configurado asi:
Os dejo también por aqui los programas que he usado en el Macbook por si os pueden ser utiles.
-Serial 1.3.2 (https://www.decisivetactics.com) 7MB
https://www.mediafire.com/file/el5uqwblmp5y5b7/srl132.zip
-TFTP Server v. 3.5.1 (http://ww2.unime.it/flr/tftpserver/) 319K
https://www.mediafire.com/file/83oc0bcdxqq9cw4/TftpServer.dmg
Espero que todo este ladrillo pueda ser util a alguien.
Gracias compañeros. Un saludo
Tki2000:
Gracias por el aporte.
Seguro que a alguien, le puede servir de mucha ayuda. >:(
zapple:
Gracias a usted Sr.Tki2000 ;) que siempre esta ahí aclarando conceptos a los novatos como yo.
Un abrazo
jar229:
Mi buen aporte >:(
Yo tengo 2 de estos routers, espero no tener que usar el método pero ... nunca se sabe ^-^
Navegación
Ir a la versión completa