Me respondo yo mismo: estaba usando una imagen que no era la correcta.
Después de varias peripecias para conseguir quemar el openWRT en un HG622 os pego el bootlog por si veis algo. Voy a "trastearlo" a ver si todo está bien. Por ahora he modificado un fichero en el etc/config y no me lo ha corrompido. ¿Esta rama tiene el SMP habilitado para compilar?
CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Mon May 30 22:11:43 CST 2011 (wangzhiquan@whg.build.huawei.com)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Boot image (0=latest, 1=previous) : 0
Board Id (0-5) : 96368MVWG_hg622
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:09:09:09
PSI Size (1-64) KBytes : 64
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 0
Support Double system.
Flash boot Flag:
Boot from main system!
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.10.24 (tki2k@tki2k-Ubuntu) (gcc version 4.6.4 (Op
enWrt/Linaro GCC 4.6-2013.05 r39156) ) #1 Tue Dec 31 20:05:37 CET 2013
[ 0.000000] Detected Broadcom 0x6368 CPU revision b2
[ 0.000000] CPU frequency is 400 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 38 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-102.6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 96368MVWG_hg622
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jff
s2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29072k/32768k available (2296k kernel code, 3696k reserve
d, 586k data, 188k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.044000] NET: Registered protocol family 16
[ 0.052000] registering PCI controller with io_map_base unset
[ 0.060000] bio: create slab <bio-0> at 0
[ 0.064000] PCI host bridge to bus 0000:00
[ 0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.072000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
[ 0.076000] pci_bus 0000:00: No busn resource found for root bus, will use [b
us 00-ff]
[ 0.092000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
[ 0.096000] Switching to clocksource MIPS
[ 0.104000] NET: Registered protocol family 2
[ 0.108000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.116000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.120000] TCP: Hash tables configured (established 512 bind 512)
[ 0.128000] TCP: reno registered
[ 0.132000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.136000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.144000] NET: Registered protocol family 1
[ 0.152000] audit: initializing netlink socket (disabled)
[ 0.156000] type=2000 audit(0.156:1): initialized
[ 0.160000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.168000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[ 0.180000] msgmni has been set to 56
[ 0.184000] io scheduler noop registered
[ 0.188000] io scheduler deadline registered (default)
[ 0.192000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_
Ê[ 0.200000] console [ttyS0] enabled, bootconsole disabled
[ 0.200000] console [ttyS0] enabled, bootconsole disabled
[ 0.212000] bcm63xx-rng bcm63xx-rng: registered RNG driver
[ 0.220000] physmap platform flash device: 08000000 at 18000000
[ 0.228000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manuf
acturer ID 0x0000c2 Chip ID 0x00227e
[ 0.236000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.244000] Amd/Fujitsu Extended Query version 1.3.
[ 0.248000] number of CFI chips: 1
[ 0.252000] bcm63xxpart: CFE boot tag found with version 6 and board type 963
68MVWG_hg622
[ 0.260000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.268000] bcm63xxpart: Partition 1 is kernel offset 20100 and length fff00
[ 0.276000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length e8000
0
[ 0.280000] bcm63xxpart: Partition 3 is cal_data offset fa0000 and length 200
00
[ 0.288000] bcm63xxpart: Partition 4 is nvram offset fe0000 and length 20000
[ 0.296000] bcm63xxpart: Partition 5 is linux offset 20000 and length f80000
[ 0.304000] bcm63xxpart: Spare partition is offset 3c0004 and length bdfffc
[ 0.312000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.316000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.324000] 0x000000000000-0x000000020000 : "CFE"
[ 0.332000] 0x000000020100-0x000000120000 : "kernel"
[ 0.336000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.352000] 0x000000120000-0x000000fa0000 : "rootfs"
[ 0.356000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.364000] mtd: partition "rootfs_data" created automatically, ofs=0x3c0000,
len=0xbe0000
[ 0.372000] 0x0000003c0000-0x000000fa0000 : "rootfs_data"
[ 0.380000] 0x000000fa0000-0x000000fc0000 : "cal_data"
[ 0.384000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.392000] 0x000000020000-0x000000fa0000 : "linux"
[ 0.400000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
[ 0.448000] b53_common: found switch: BCM63xx, rev 0
[ 0.452000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.464000] TCP: cubic registered
[ 0.464000] NET: Registered protocol family 17
[ 0.472000] 8021q: 802.1Q VLAN Support v1.8
[ 0.480000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.488000] Freeing unused kernel memory: 188K (802e1000 - 80310000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
[ 2.652000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-
duplex
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 4.128000] usbcore: registered new interface driver usbfs
[ 4.132000] usbcore: registered new interface driver hub
[ 4.140000] usbcore: registered new device driver usb
[ 4.152000] Button Hotplug driver version 0.4.1
[ 4.164000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.172000] ehci-platform: EHCI generic platform driver
[ 4.280000] ehci-platform ehci-platform: EHCI Host Controller
[ 4.284000] ehci-platform ehci-platform: new USB bus registered, assigned bus
number 1
[ 4.292000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
[ 4.312000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurr
ent ignored
[ 4.320000] hub 1-0:1.0: USB hub found
[ 4.324000] hub 1-0:1.0: 2 ports detected
[ 4.332000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.340000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 4.348000] ohci-platform ohci-platform: new USB bus registered, assigned bus
number 2
[ 4.356000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600
[ 4.420000] hub 2-0:1.0: USB hub found
[ 4.424000] hub 2-0:1.0: 1 port detected
[ 4.432000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/i
nput/input0
mount_root: jffs2 is ready
[ 6.244000] jffs2: notice: (225) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead,
2 orphan) found.
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 8.464000] NET: Registered protocol family 10
[ 9.112000] wl: module license 'unspecified' taints kernel.
[ 9.116000] Disabling lock debugging due to kernel taint
[ 9.220000] SSB/BCMA glue driver successfully attached
[ 9.236000] nf_conntrack version 0.5.0 (457 buckets, 1828 max)
[ 9.252000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.280000] Loading modules backported from Linux version master-2013-11-05-0
-gafa3093
[ 9.288000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 9.304000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.360000] xt_time: kernel timezone is -0000
[ 9.396000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.408000] cfg80211: World regulatory domain updated:
[ 9.412000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp)
[ 9.420000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)
[ 9.428000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)
[ 9.436000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20
00 mBm)
[ 9.444000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 20
00 mBm)
[ 9.452000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 20
00 mBm)
[ 9.460000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0
mBm)
[ 9.576000] PPP generic driver version 2.4.2
[ 9.584000] NET: Registered protocol family 24
[ 9.628000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP
ROM data from 'rt2x00.eeprom'.
[ 9.640000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 d
etected
[ 9.648000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[ 13.024000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-
duplex
[ 16.840000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port4, 100Mbps, full-
duplex
[ 16.848000] device eth0.1 entered promiscuous mode
[ 16.856000] device eth0 entered promiscuous mode
[ 16.864000] br-lan: port 1(eth0.1) entered forwarding state
[ 16.868000] br-lan: port 1(eth0.1) entered forwarding state
procd: - init complete -
[ 17.836000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 18.872000] br-lan: port 1(eth0.1) entered forwarding state