(http://i1273.photobucket.com/albums/y418/Tki2000/thumb_X8_zps6ixxetap.jpg) | Descripción breve del router: CPU: Qualcomm QCA9558@720MHz RAM: 128MB Flash: 16MB 1xWAN: 1000BaseT 4xLAN: 1000BaseT USB: 1xUSB2.0 - 1xUSB3.0 Wifi: Dual Band 2,4Ghz / 5,8Ghz / bgn 3x3 / ac 3x3 |
mtd -r write /tmp/imagen.bin firmware
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
setenv op_code 1
saveenv
reset
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
You choosed 4
0
CFG_KERN_ADDR=0x9F040000
4: System Enter Boot Command Line Interface.
U-Boot 0.0.9 (Feb 18 2013 - 14:56:17)
Hit any key to stop autoboot: 0
ath>setenv op_code 1
ath>saveenv
ath>reset
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
You choosed 2
0
CFG_KERN_ADDR=0x9F040000
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.99.9) ==:192.168.1.1
Input server IP (192.168.99.8) ==:192.168.1.100
Input Linux Kernel filename (uImageNBG6716) ==:openwrt.bin
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'openwrt.bin'.
Load address: 0x8060000
Loading: Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############
done
Bytes transferred = 8716292 (850004 hex)
NetBootFileXferSize= 00850004
Un-Protected 253 sectors
Erase linux kernel block !!
From 0x9F040000 To 0x9F89FFFF
Erasing flash...
First 0x4 last 0x89 sector size 0x10000
137
Erased 134 sectors
Copy linux image[8716292 byte] from[0x08060000] to Flash[0x9F040000]....
Copy to Flash... write addr: 9f040000
done
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-3.18.11
Created: 2015-04-21 16:27:25 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1237943 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ...
ath> printenv
Reg 0x00[1302]
port0 RXBROAD=0
port0 TXBROAD=3
port0 TXUNDERRUN=0
port0 TX64BYTE=0
port0 TX128BYTE=5
phy 0 no link
phy0 speed=0
port1 RXBROAD=0
port1 TXBROAD=0
port1 TXUNDERRUN=0
port1 TX64BYTE=0
port1 TX128BYTE=0
phyBase=0,phyAddr=1
phy1 speed=110
port2 RXBROAD=3
port2 TXBROAD=0
port2 TXUNDERRUN=0
port2 TX64BYTE=0
port2 TX128BYTE=0
phy 2 no link
phy2 speed=0
port3 RXBROAD=0
port3 TXBROAD=0
port3 TXUNDERRUN=0
port3 TX64BYTE=0
port3 TX128BYTE=0
phy 3 no link
phy3 speed=0
port4 RXBROAD=0
port4 TXBROAD=0
port4 TXUNDERRUN=0
port4 TX64BYTE=0
port4 TX128BYTE=0
phy 4 no link
phy4 speed=0
port5 RXBROAD=0
port5 TXBROAD=0
port5 TXUNDERRUN=0
port5 TX64BYTE=0
port5 TX128BYTE=0
port6 RXBROAD=0
port6 TXBROAD=0
port6 TXUNDERRUN=0
port6 TX64BYTE=0
port6 TX128BYTE=0
bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs,jffs2 init=/sbin/in
it mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),2752k(rootfs),1408k(uImage),64
k(NVRAM),64k(ART)
bootcmd=bootm 0x9f040000
bootdelay=2
baudrate=115200
ethaddr="64:--:A3:--:44:--"
ipaddr=192.168.99.9
serverip=192.168.99.8
sn=139--62--
hw_ver=1.0.0
hw_id=02220056
pro_id=000
country=000
domain=1
wanaddr=64:--:A3:--:44:--
wlanaddr=00:AA:BB:CC:DD:12
snextra=139336220***********
bootfile=uImageNBG6716
dir=
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr
0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}ap136${bc}-jffs2&&erase 0x9f050000 +0x630000&&cp.b $fil
eaddr 0x9f050000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f680000 +$filesize&&
cp.b $fileaddr 0x9f680000 $filesize
ethact=eth0
uboot_ver=0.0.9.1
op_mode=1
stdin=serial
stdout=serial
stderr=serial
Environment size: 890/65532 bytes
ath>
>:( >:( >:( >:(Lo mismo digo, tiene muy buena pinta, pero le falla el precio.
Tiene muy buena pinta este router, lo malo es el precio ;D
>:( >:( >:( >:(Lo mismo digo, tiene muy buena pinta, pero le falla el precio.
Tiene muy buena pinta este router, lo malo es el precio ;D
Yo acabo de adquirir un Archer C7 en amazon, que es un poco más barato.
El problema del Archer C7 es que te la juegas a ver si es la v2 (con soporte para WiFi AC) o la v1 (sin soporte para WiFi AC), pero amazon no pone ninguna pega en cuento a las devoluciones...
En mi caso tuve suerte y me llegó era la v2, aunque creo que ya sólo envían la v2.
Saludos.