Autor Tema: [Desarrollo] OpenWRT para routers Astoria de ya.com (ARV4518/ARV7518) (Leído 653530 veces)

Pteridium · « **Respuesta #380 en:** 23-01-2013, 00:10 (Miércoles) »

Cita de: Yo_Julio en 22-01-2013, 22:29 (Martes)

Hola, es mi primer post, aunque me he leido el hilo de arriba abajo, (creo) no consigo arrancar el 4518

He tratado de cargar la imagen de que ha enlazado Pteridium en el primer post www.mediafire.com/?2w34c64cuhnhw3c y parece como si no encontrara una partición:

Aquí se queda colgado.
Parece como si le faltara al kernel algún driver de pci

Y hasta aquí llego.
Si alguien puede arrojar algo de luz...

Saludos.

A Lesgar le pasa algo parecido. En el enlace de abajo va el uboot que tengo en el 4518 y que nunca ha dado problemas.
Asegúrate, antes de grabarlo en la flash, de desprotegerla con el comando protect off all.
http://www.mediafire.com/?5kla1uoa9110e32
Para subirlo escribe en uboot "run update_uboot", que lo que hace es subir a memoria un archivo con nombre uboot.bin (tendrás que renombrar el del enlace) y grabarlo en la flash si se ha desprotegido previamente.

jar229 · « **Respuesta #381 en:** 23-01-2013, 08:16 (Miércoles) »

Citar

Por cierto, ¿alguien sabe cómo se hace para que muestre todo el bootlog pulsando un recuadro gris?, que este troncho que sale de buenas a primeras ocupa mucho.

Eso se podía hacer con la etiqueta spoiler (el icono que está junto a quote) pero por problemas con el foro, está desactivado

Yo_Julio · « **Respuesta #382 en:** 23-01-2013, 19:19 (Miércoles) »

Hola otra vez Pteridium.

He cargado el U_boot y da el mismo error.
no uImage or brnImage or eva found in linux partition
Can't split linux partition
y finalmente
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

El problema es que ahora con este U_boot no puedo hacer tftp, en el log del servidor conecta pero no transfiere, da un error de ack. Por tanto no puedo volver a dejar el uboot que tenía y menos cargar otra imagen.

¿Hay alguna forma de mandarle el loader via serial console o tengo que hacer la ñapa para ponerlo en UART mode? ¿o alguna otra opción?

Esto de no saber...

Pteridium · « **Respuesta #383 en:** 23-01-2013, 23:31 (Miércoles) »

https://www.dropbox.com/s/nhqhezlsgy9a8ny/openwrt-lantiq-xway-ARV4518PW-uImage

Imagen RAM para el 4518 que se puede instalar mediante httpd de uboot. Tiene soporte para ext2, 3, 4 y USB.

Casi estoy empezando a pensar que hay alguna revisión del 4518 que no es compatible...

En la pegatina inferior del router con el que hago las pruebas pone "HW Version: R01A"

Lesgar · « **Respuesta #384 en:** 24-01-2013, 17:24 (Jueves) »

En el mío pone "HW Version: R01" no lleva la A. Es posible que el kernel pánic venga por una diferencia en el hardware?

Pteridium · « **Respuesta #385 en:** 24-01-2013, 17:49 (Jueves) »

Cita de: Lesgar en 24-01-2013, 17:24 (Jueves)

En el mío pone "HW Version: R01" no lleva la A. Es posible que el kernel pánic venga por una diferencia en el hardware?

Mecagüenla. Como sea eso...

Edición:
Foto de una placa R01. Aparentemente son iguales.
http://imageshack.us/f/155/img1885ns.jpg/
Si alguien puede poner el modelo de flash que lleva esta revisón sería genial.
A revisar el código que se encarga de las particiones...

sephir0t00 · « **Respuesta #386 en:** 24-01-2013, 17:54 (Jueves) »

Sí, es posible que sea eso, porque yo tengo 3 arv4518, 2 de ellos R01A que sí he podido instalar openwrt y 1 R01 que creo recordar también me daba un kernel panic.

Pteridium · « **Respuesta #387 en:** 24-01-2013, 19:08 (Jueves) »

https://www.dropbox.com/s/kbqicp97vkhccj1/openwrt-lantiq-xway-ARV4518PW-squashfs.image

Esta imagen tiene unas opciones adicionales para detectar la flash. A ver si vale de algo...
El que la pruebe que me mande o ponga en el foro el bootlog.

sephir0t00 · « **Respuesta #388 en:** 24-01-2013, 19:57 (Jueves) »

Buenas, pues ya he probado la imagen que has subido y sigue con el kernel panic.

Te pongo aquí el bootlog del firmware original, por si te sirve de algo:
https://dl.dropbox.com/u/18460228/openwrt/ARV4518-R01-original.log

Y aquí el de la imagen de openwrt:
https://dl.dropbox.com/u/18460228/openwrt/bootlog-openwrt-AR4518-R01.txt

Y muchísimas gracias por intentar solucionarlo ^^.

Pteridium · « **Respuesta #389 en:** 24-01-2013, 20:33 (Jueves) »

Cita de: sephir0t00 en 24-01-2013, 19:57 (Jueves)

Buenas, pues ya he probado la imagen que has subido y sigue con el kernel panic.

Te pongo aquí el bootlog del firmware original, por si te sirve de algo:
https://dl.dropbox.com/u/18460228/openwrt/ARV4518-R01-original.log

Y aquí el de la imagen de openwrt:
https://dl.dropbox.com/u/18460228/openwrt/bootlog-openwrt-AR4518-R01.txt

Y muchísimas gracias por intentar solucionarlo ^^.

Muchísimas gracias por el bootlog.

Ya he mandado un ticket explicando la incidencia.
https://dev.openwrt.org/ticket/12884#ticket
dentro de un rato cuelgo una imagen sin bus pci a ver si funciona o si da errores de flash, ya que están los dos conectados al mismo bus interno.

Lesgar · « **Respuesta #390 en:** 24-01-2013, 21:04 (Jueves) »

Subo dos imagenes antiguas que funcionan con openwrt. Una para cargar con el Brnboot y otra para cargar desde uboot. Si necesitais ver el boot de arranque, lsmod, dmesg o algo mas no teneis mas que pedirlo y lo subo al foro. Esta imagen no da kernel panic en mi arv4518 hardware versión R01, pero es mas viejo k la tos (kernel 2.26 y viene pelado,sin LUCI ni nada). No lo he compilado yo, de tooodos lo que me he bajado de internet es el único que funciona.
https://www.dropbox.com/s/f3dqlc2q7hl5khb/arv4518_R01_openwrt_UBOOT.rar
https://www.dropbox.com/s/rypdk0ysvhzc5qr/arv4518_R01_openwrt_BRNBOOT.rar

Lesgar · « **Respuesta #391 en:** 24-01-2013, 21:20 (Jueves) »

Aqui el bootlog de la imagen que has subido, ke tambien da kernel panic

Flash LIMPIA
-------------------------------------------------------------------------------------------------
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
*** Warning - bad CRC, using default environment

Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-24 17:51:16 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1230778 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.2 (pepe@debian) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Thu Jan 24 18:51:02 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00068a70
[ 0.000000] Readback ErrCtl register=00068a70
[ 0.000000] Memory: 61072k/65536k available (2630k kernel code, 4464k reserved, 816k data, 192k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] Data bus error, epc == 8028d90c, ra == 8028d8f4
[ 0.084000] Oops[#1]:
[ 0.084000] Cpu 0
[ 0.084000] $ 0 : 00000000 00000000 be105400 feffffff
[ 0.084000] $ 4 : ffffffff 803b8fd0 00000001 000041c6
[ 0.084000] $ 8 : 8385a620 00000002 00000001 ffffff80
[ 0.084000] $12 : 03ff0000 03bd0000 00000000 ac000000
[ 0.084000] $16 : 8385a590 803c0000 8385a580 803c0000
[ 0.084000] $20 : 81002078 803c0000 803c0000 803c0000
[ 0.084000] $24 : 00000018 80157df0
[ 0.084000] $28 : 8381c000 8381dd58 8033c05c 8028d8f4
[ 0.084000] Hi : 00000000
[ 0.084000] Lo : 00000000
[ 0.084000] epc : 8028d90c ltq_pci_probe+0x230/0x484
[ 0.084000] Not tainted
[ 0.084000] ra : 8028d8f4 ltq_pci_probe+0x218/0x484
[ 0.084000] Status: 1100fc03 KERNEL EXL IE
[ 0.084000] Cause : 1080001c
[ 0.084000] PrId : 00019641 (MIPS 24KEc)
[ 0.084000] Modules linked in:
[ 0.084000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)
[ 0.084000] Stack : 8385a598 ffffffed 80341280 803581e4 0000001e 8385a590 803c0000 803581e4
ffffffed 80341280 803581e4 0000001e 80360210 80184d44 0000001e 83858180
8385a590 803581e4 803581e4 80186958 834015e0 8385a5c4 8385a590 803581e4
803581e4 00000000 80390000 80184fdc 803581e4 80182d24 83858180 00000000
00000000 803581e4 80184f70 80183020 83813148 00000000 80352b10 80182ca4
...
[ 0.084000] Call Trace:
[ 0.084000] [<8028d90c>] ltq_pci_probe+0x230/0x484
[ 0.084000] [<80184d44>] driver_probe_device+0x1d8/0x404
[ 0.084000] [<80184fdc>] __driver_attach+0x6c/0xa4
[ 0.084000] [<80183020>] bus_for_each_dev+0x54/0x98
[ 0.084000] [<80184114>] bus_add_driver+0xe8/0x270
[ 0.084000] [<80185380>] driver_register+0xbc/0x178
[ 0.084000] [<80373614>] pcibios_init+0x18/0x40
[ 0.084000] [<80006500>] do_one_initcall+0xf0/0x1c0
[ 0.084000] [<80285a1c>] kernel_init+0x138/0x2c0
[ 0.084000] [<8000b41c>] kernel_thread_helper+0x10/0x18
[ 0.084000]
[ 0.084000]
Code: 8c440030 3c03feff 3463ffff <00831824> ac430030 0000000f 8e63ad70 8e22ad74 3c058032
[ 0.088000] ---[ end trace 139ce121c98e96c9 ]---
[ 0.092000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.092000]
-------------------------------------------------------------------------------------------------

Flash setenv kernel_addr 0xb0020000

-------------------------------------------------------------------------------------------------
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-24 17:51:16 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1230778 Bytes = 1.2 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.2 (pepe@debian) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Thu Jan 24 18:51:02 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00068a70
[ 0.000000] Readback ErrCtl register=00068a70
[ 0.000000] Memory: 61072k/65536k available (2630k kernel code, 4464k reserved, 816k data, 192k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] Data bus error, epc == 8028d90c, ra == 8028d8f4
[ 0.084000] Oops[#1]:
[ 0.084000] Cpu 0
[ 0.084000] $ 0 : 00000000 00000000 be105400 feffffff
[ 0.084000] $ 4 : ffffffff 803b8fd0 00000001 000041c6
[ 0.084000] $ 8 : 8385a620 00000002 00000001 ffffff80
[ 0.084000] $12 : 03ff0000 03bd0000 00000000 ac000000
[ 0.084000] $16 : 8385a590 803c0000 8385a580 803c0000
[ 0.084000] $20 : 81002078 803c0000 803c0000 803c0000
[ 0.084000] $24 : 00000018 80157df0
[ 0.084000] $28 : 8381c000 8381dd58 8033c05c 8028d8f4
[ 0.084000] Hi : 00000000
[ 0.084000] Lo : 00000000
[ 0.084000] epc : 8028d90c ltq_pci_probe+0x230/0x484
[ 0.084000] Not tainted
[ 0.084000] ra : 8028d8f4 ltq_pci_probe+0x218/0x484
[ 0.084000] Status: 1100fc03 KERNEL EXL IE
[ 0.084000] Cause : 1080001c
[ 0.084000] PrId : 00019641 (MIPS 24KEc)
[ 0.084000] Modules linked in:
[ 0.084000] Process swapper (pid: 1, threadinfo=8381c000, task=8381b958, tls=00000000)
[ 0.084000] Stack : 8385a598 ffffffed 80341280 803581e4 0000001e 8385a590 803c0000 803581e4
ffffffed 80341280 803581e4 0000001e 80360210 80184d44 0000001e 83858180
8385a590 803581e4 803581e4 80186958 834015e0 8385a5c4 8385a590 803581e4
803581e4 00000000 80390000 80184fdc 803581e4 80182d24 83858180 00000000
00000000 803581e4 80184f70 80183020 83813148 00000000 80352b10 80182ca4
...
[ 0.084000] Call Trace:
[ 0.084000] [<8028d90c>] ltq_pci_probe+0x230/0x484
[ 0.084000] [<80184d44>] driver_probe_device+0x1d8/0x404
[ 0.084000] [<80184fdc>] __driver_attach+0x6c/0xa4
[ 0.084000] [<80183020>] bus_for_each_dev+0x54/0x98
[ 0.084000] [<80184114>] bus_add_driver+0xe8/0x270
[ 0.084000] [<80185380>] driver_register+0xbc/0x178
[ 0.084000] [<80373614>] pcibios_init+0x18/0x40
[ 0.084000] [<80006500>] do_one_initcall+0xf0/0x1c0
[ 0.084000] [<80285a1c>] kernel_init+0x138/0x2c0
[ 0.084000] [<8000b41c>] kernel_thread_helper+0x10/0x18
[ 0.084000]
[ 0.084000]
Code: 8c440030 3c03feff 3463ffff <00831824> ac430030 0000000f 8e63ad70 8e22ad74 3c058032
[ 0.088000] ---[ end trace 139ce121c98e96c9 ]---
[ 0.092000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 0.092000]

Pteridium · « **Respuesta #392 en:** 24-01-2013, 21:37 (Jueves) »

https://www.dropbox.com/s/kbqicp97vkhccj1/openwrt-lantiq-xway-ARV4518PW-squashfs.image

Imagen con bus pci deshabilitado y que hace varios tests en la flash. Cuando la probéis poned el bootlog para añadirlo al ticket que está abierto, o añadidlo vosotros si lo preferís.

Si alguien puede poner marca y modelo de la flash estaría genial.

Noltari · « **Respuesta #393 en:** 24-01-2013, 22:25 (Jueves) »

Lo del Bus PCI es muy raro. No entiendo qué es lo que puede estar pasando, pero a ver si las compilaciones sin PCI arrojan algo de luz :$...

Cambiando de tema, aquí tenéis mi particular versión del UART MOD para el ARV7518:

Saludos!

sephir0t00 · « **Respuesta #394 en:** 24-01-2013, 23:12 (Jueves) »

Pues acabo de probar el ultimo firmware que has puesto. Aqui tienes el bootlog:
https://dl.dropbox.com/u/18460228/openwrt/bootlog-openwrt-AR4518-R01-1.log

Aqui los datos de la flash
EON
EN29LV320B-70TCP

Pteridium · « **Respuesta #395 en:** 24-01-2013, 23:44 (Jueves) »

https://www.dropbox.com/s/6xds0xp3pyljnol/openwrt-ARV4518PW-no_PCI-squashfs.image

A este le he quitado todo lo que pude relacionado con PCI. A ver...

sephir0t00 · « **Respuesta #396 en:** 24-01-2013, 23:54 (Jueves) »

~~Ya parece que va avanzando, ahora da otro kernel panic:~~
~~Nuevo bootlog:~~
~~https://dl.dropbox.com/u/18460228/openwrt/bootlog-openwrt-AR4518-R01-NOPCI.log~~

Editado:

Ya funciona openwrt, era error mío, actualizaba desde la imagen anterior de openwrt. Haciéndolo desde el firmware original (instalar uboot y luego subir la imagen del firmware) funciona perfectamente.

Muchas gracias, Pteridium.

Ya nos dirás que le has tocado al compilar el firmware.

Lesgar · « **Respuesta #397 en:** 25-01-2013, 00:26 (Viernes) »

¡¡¡ QUE GRANDE ERES !!!
Ya funciona en mi Arv4518 HV: R01
Te adjunto el bootlog + kernel log y si no es mucho pedir me explicas cual es el problema, a ver si poco a poco vamos aprendiendo...
Putty.log
----------------------------------------------------------------------------
Bytes transferred = 2883588 (2c0004 hex)
http upload ready

## Checking Image at 80500000 ...
Legacy image found
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-24 22:27:12 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1186170 Bytes = 1.1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
http ugrade ...

............................................. done
Erased 45 sectors
Copy to Flash... 9....8....7....6....5....4....3....2....1....done
http ugrade ready

ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

U-Boot 2010.03 (Sep 19 2012 - 22:34:24)

Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.3, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 4 MB
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.7.2
Created: 2013-01-24 22:27:12 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1186170 Bytes = 1.1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.7.2 (pepe@debian) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Thu Jan 24 23:26:56 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61208k/65536k available (2541k kernel code, 4328k reserved, 777k data, 192k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.104000] bio: create slab <bio-0> at 0
[ 0.112000] usbcore: registered new interface driver usbfs
[ 0.116000] usbcore: registered new interface driver hub
[ 0.120000] usbcore: registered new device driver usb
[ 0.124000] Switching to clocksource MIPS
[ 0.132000] NET: Registered protocol family 2
[ 0.140000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.144000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.152000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.160000] TCP: reno registered
[ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.168000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.176000] NET: Registered protocol family 1
[ 0.180000] gptu: totally 6 16-bit timers/counters
[ 0.184000] gptu: misc_register on minor 63
[ 0.188000] gptu: succeeded to request irq 126
[ 0.192000] gptu: succeeded to request irq 127
[ 0.196000] gptu: succeeded to request irq 128
[ 0.204000] gptu: succeeded to request irq 129
[ 0.208000] gptu: succeeded to request irq 130
[ 0.212000] gptu: succeeded to request irq 131
[ 0.224000] lantiq,vmmc 1f103000.vmmc: requested GPIO 255
[ 0.228000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03900000
[ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.244000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.256000] msgmni has been set to 119
[ 0.260000] io scheduler noop registered
[ 0.264000] io scheduler deadline registered (default)
[ 0.268000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.292000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022f9
[ 0.300000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.304000] Amd/Fujitsu Extended Query version 1.1.
[ 0.312000] number of CFI chips: 1
[ 0.312000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.320000] Creating 4 MTD partitions on "ltq_nor":
[ 0.324000] 0x000000000000-0x000000010000 : "uboot"
[ 0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.340000] 0x000000020000-0x0000003f0000 : "linux"
[ 0.344000] found squashfs behind kernel
[ 0.348000] Creating 2 MTD partitions on "ltq_nor":
[ 0.352000] 0x000000020000-0x0000001419ba : "kernel"
[ 0.356000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.372000] 0x0000001419ba-0x0000003f0000 : "rootfs"
[ 0.376000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] mtd: partition "rootfs" set to be root filesystem
[ 0.396000] mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=140000
[ 0.404000] 0x0000002b0000-0x0000003f0000 : "rootfs_data"
[ 0.412000] 0x0000003f0000-0x000000400000 : "boardconfig"
[ 0.440000] libphy: ltq_mii: probed
[ 0.472000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
[ 0.476000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.488000] wdt 1f8803f0.watchdog: Init done
[ 0.492000] leds-gpio gpio-leds.5: pins are not configured from the driver
[ 0.508000] TCP: cubic registered
[ 0.508000] NET: Registered protocol family 17
[ 0.512000] 8021q: 802.1Q VLAN Support v1.8
[ 0.536000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.540000] Freeing unused kernel memory: 192k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -

Please press Enter to activate this console. [ 10.052000] SCSI subsystem initialized
[ 11.120000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.544000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 12.208000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 12.716000] IFXUSB: USB core #0 soft-reset
[ 12.920000] IFXUSB: USB core #0 soft-reset
[ 12.920000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 12.928000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 12.936000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 12.940000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[ 12.944000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[ 12.952000] IFXUSB: Init: Power Port (0)
[ 12.956000] hub 1-0:1.0: USB hub found
[ 12.960000] hub 1-0:1.0: 1 port detected
[ 12.964000] ifxusb_hcd ifxusb_hcd: requested GPIO 238
[ 13.092000] Initializing USB Mass Storage driver...
[ 13.096000] usbcore: registered new interface driver usb-storage
[ 13.104000] USB Mass Storage support registered.
[ 18.368000] device eth0 entered promiscuous mode
[ 18.376000] br-lan: port 1(eth0) entered forwarding state
[ 18.380000] br-lan: port 1(eth0) entered forwarding state
[ 20.384000] br-lan: port 1(eth0) entered forwarding state
[ 56.184000] jffs2: notice: (1242) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 133.792000] br-lan: port 1(eth0) entered disabled state
[ 133.812000] device eth0 left promiscuous mode
[ 133.812000] br-lan: port 1(eth0) entered disabled state
[ 133.856000] device eth0 entered promiscuous mode
[ 133.888000] br-lan: port 1(eth0) entered forwarding state
[ 133.892000] br-lan: port 1(eth0) entered forwarding state
[ 135.896000] br-lan: port 1(eth0) entered forwarding state

------------------------------------------------------------------------------------------------------------------------
kernel log

[ 0.000000] Linux version 3.7.2 (pepe@debian) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Thu Jan 24 23:26:56 CET 2013
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Board: ARV4518PW - SMC7908A-ISP, Airties WAV-221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8033bf60, node_mem_map 81002ac0
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc:

0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61208k/65536k available (2541k kernel code, 4328k reserved, 777k data, 192k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.036000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.104000] bio: create slab <bio-0> at 0
[ 0.112000] usbcore: registered new interface driver usbfs
[ 0.116000] usbcore: registered new interface driver hub
[ 0.120000] usbcore: registered new device driver usb
[ 0.124000] Switching to clocksource MIPS
[ 0.132000] NET: Registered protocol family 2
[ 0.140000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.144000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.152000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.160000] TCP: reno registered
[ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.168000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.176000] NET: Registered protocol family 1
[ 0.180000] gptu: totally 6 16-bit timers/counters
[ 0.184000] gptu: misc_register on minor 63
[ 0.188000] gptu: succeeded to request irq 126
[ 0.192000] gptu: succeeded to request irq 127
[ 0.196000] gptu: succeeded to request irq 128
[ 0.204000] gptu: succeeded to request irq 129
[ 0.208000] gptu: succeeded to request irq 130
[ 0.212000] gptu: succeeded to request irq 131
[ 0.224000] lantiq,vmmc 1f103000.vmmc: requested GPIO 255
[ 0.228000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03900000
[ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.244000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.256000] msgmni has been set to 119
[ 0.260000] io scheduler noop registered
[ 0.264000] io scheduler deadline registered (default)
[ 0.268000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 0.276000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.292000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022f9
[ 0.300000] ltq_nor: Found an alias at 0x400000 for the chip at 0x0
[ 0.300000] ltq_nor: Found an alias at 0x800000 for the chip at 0x0
[ 0.300000] ltq_nor: Found an alias at 0xc00000 for the chip at 0x0
[ 0.300000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.304000] Amd/Fujitsu Extended Query version 1.1.
[ 0.312000] number of CFI chips: 1
[ 0.312000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.320000] Creating 4 MTD partitions on "ltq_nor":
[ 0.324000] 0x000000000000-0x000000010000 : "uboot"
[ 0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.340000] 0x000000020000-0x0000003f0000 : "linux"
[ 0.344000] found squashfs behind kernel
[ 0.348000] Creating 2 MTD partitions on "ltq_nor":
[ 0.352000] 0x000000020000-0x0000001419ba : "kernel"
[ 0.356000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.372000] 0x0000001419ba-0x0000003f0000 : "rootfs"
[ 0.376000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.392000] mtd: partition "rootfs" set to be root filesystem
[ 0.396000] mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=140000
[ 0.404000] 0x0000002b0000-0x0000003f0000 : "rootfs_data"
[ 0.412000] 0x0000003f0000-0x000000400000 : "boardconfig"
[ 0.440000] libphy: ltq_mii: probed
[ 0.472000] Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
[ 0.476000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.488000] wdt 1f8803f0.watchdog: Init done
[ 0.492000] leds-gpio gpio-leds.5: pins are not configured from the driver
[ 0.500000] Registered led device: power
[ 0.500000] Registered led device: dsl
[ 0.500000] Registered led device: online
[ 0.500000] Registered led device: wifi
[ 0.500000] Registered led device: wps
[ 0.500000] Registered led device: dsl2
[ 0.504000] Registered led device: usb
[ 0.504000] Registered led device: voice
[ 0.504000] Registered led device: fxs1
[ 0.504000] Registered led device: fxs2
[ 0.504000] Registered led device: fxo
[ 0.508000] TCP: cubic registered
[ 0.508000] NET: Registered protocol family 17
[ 0.512000] 8021q: 802.1Q VLAN Support v1.8
[ 0.536000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.540000] Freeing unused kernel memory: 192k freed
[ 10.052000] SCSI subsystem initialized
[ 11.120000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.544000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 12.208000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 12.716000] IFXUSB: USB core #0 soft-reset
[ 12.920000] IFXUSB: USB core #0 soft-reset
[ 12.920000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 12.928000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 12.936000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 12.940000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[ 12.944000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[ 12.952000] IFXUSB: Init: Power Port (0)
[ 12.956000] hub 1-0:1.0: USB hub found
[ 12.960000] hub 1-0:1.0: 1 port detected
[ 12.964000] ifxusb_hcd ifxusb_hcd: requested GPIO 238
[ 13.092000] Initializing USB Mass Storage driver...
[ 13.096000] usbcore: registered new interface driver usb-storage
[ 13.104000] USB Mass Storage support registered.
[ 18.368000] device eth0 entered promiscuous mode
[ 18.376000] br-lan: port 1(eth0) entered forwarding state
[ 18.380000] br-lan: port 1(eth0) entered forwarding state
[ 20.384000] br-lan: port 1(eth0) entered forwarding state
[ 42.560000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 42.560000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 42.560000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 56.184000] jffs2: notice: (1242) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 133.792000] br-lan: port 1(eth0) entered disabled state
[ 133.812000] device eth0 left promiscuous mode
[ 133.812000] br-lan: port 1(eth0) entered disabled state
[ 133.856000] device eth0 entered promiscuous mode
[ 133.888000] br-lan: port 1(eth0) entered forwarding state
[ 133.892000] br-lan: port 1(eth0) entered forwarding state
[ 135.896000] br-lan: port 1(eth0) entered forwarding state

Voy a ver si soy capaz de hacer que funcione el modem ADSL. Lo dicho MUCHAS GRACIAS

Pteridium · « **Respuesta #398 en:** 25-01-2013, 09:47 (Viernes) »

¡Caray! Me alegro un montón que hayamos podido resolverlo, aunque a costa de perder, en principio, la wifi. Quedaría por probar si el puerto USB y la parte de ADSL funcionan bien.
Que esté "funcionando" es gracias a vosotros que os habéis tomado las molestias de probar las imágenes.

En los R01 hay algún problema con el bus PCI o que se configure de manera diferente a los R01A, y habrá que investigarlo.

Voy a darle algunas vueltas al código e intentaré "hablarlo" con blogic.

¡Gracias por vuestro esfuerzo!

Edición 1:
Ticket ampliado gracias al trabajo de sephir0t00 y Lesgar. Lo he marcado como enchancement ya que creo que nunca nadie se dio cuenta del detalle de las revisiones de hardware.
https://dev.openwrt.org/ticket/12884

Edición 2:
ARV4518PW-R01-normal-trunk
Firm para el ARV4518PW Revisión R01. Todavía falta por verificar si el puerto USB funciona. Se incluyen los .config de OpenWRT para ver los paquetes que hay compilados y del kernel.
ARV4518PW-R01-apretado-trunk
En este se han usado las flags -02 -march=24kec -mtune=24kec -mdsp

sephir0t00 · « **Respuesta #399 en:** 25-01-2013, 19:27 (Viernes) »

Buenas, Pteridium he probado la imagen 'ARV4518PW-R01-apretado-trunk' y funciona perfectamente el USB.
Por cierto, y tan apretado, casi ni cabe en la flash ^^.

Noticias:

Autor Tema: [Desarrollo] OpenWRT para routers Astoria de ya.com (ARV4518/ARV7518) (Leído 653530 veces)

Pteridium

Yo_Julio

Pteridium

Lesgar

Pteridium

sephir0t00

Pteridium

sephir0t00

Pteridium

Lesgar

Lesgar

Pteridium

Noltari

sephir0t00

Pteridium

sephir0t00

Lesgar

Pteridium

sephir0t00