Equipos y materiales > Openwrt & LEDE |
[Desarrollo] OpenWrt en ZTE IX350 |
(1/7) > >> |
mekkon:
Buenas, Abro este hilo para añadir soporte para OpenWrt para el ZTE IX350. No esta soportado aún, pero tengo una versión funcional con soporte para wifi y ethernet. CPU: RT3052F RAM: H57V2562GTR-75C (32MB) FLASH: S29GL128N (16MB) Ethernet: 4x RJ45 10/100 H4001CG Para curiosear por el router he utilizado un conversor TTL-USB serial conectado de esta forma: El arranque dispone de Uboot: --- Código: ---U-Boot 1.1.3 (Apr 7 2011 - 19:55:01) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fac000 mips_cpu_feq=384000000 Set info->start[0]=BF000000 flash_protect ON: from 0xBF000000 to 0xBF0208B3 protect on 0 protect on 1 protect on 2 flash_protect ON: from 0xBF040000 to 0xBF05FFFF protect on 4 protect on 5 *** Warning - bad CRC, using default environment ============================================ ZTE UBoot Version: 1.0.1 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM COMPONENT: 256Mbits DRAM BUS: 16BIT Total memory: 32 MBytes Date:Apr 7 2011 Time:19:55:01 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 freq = 384000000 MHZ ##### The CPU freq = 384 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes All PHY are used. Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. --- Fin del código --- Si escogemos la opción 4 nos salen estas opciones: --- Código: ---ZTE # ? ? - alias for 'help' loopback - Ralink eth loopback test !! boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol cp - memory copy echo - echo args to console erase - erase FLASH memory go - start application at address 'addr' help - print online help loadb - load binary file over serial line (kermit mode) md - memory display mdio - Ralink PHY register R/W command !! mm - memory modify (auto-incrementing) mw - memory write (fill) nm - memory modify (constant address) printenv- print environment variables protect - enable or disable FLASH write protection reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables spicmd - read/write data from/to eeprom or vtss tftpboot- boot image via network using TFTP protocol version - print monitor version --- Fin del código --- --- Código: ---ZTE # printenv bootcmd=tftp bootdelay=5 baudrate=115200 ethaddr="00:AA:BB:CC:DD:10" ipaddr=192.168.0.1 serverip=192.168.0.22 preboot=echo;echo ramargs=setenv bootargs root=/dev/ram rw addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1 flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr) kernel_addr=BFC40000 u-boot=u-boot.bin load=tftp 8A100000 $(u-boot) u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize) loadfs=tftp 8A100000 root.cramfs u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize) test_tftp=tftp 8A100000 root.cramfs;run test_tftp stdin=serial stdout=serial stderr=serial ethact=Eth0 (10/100-M) Environment size: 785/131068 bytes --- Fin del código --- este es el log completo de arranque del aparato: --- Código: ---U-Boot 1.1.3 (Apr 7 2011 - 19:55:01) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fac000 mips_cpu_feq=384000000 Set info->start[0]=BF000000 flash_protect ON: from 0xBF000000 to 0xBF0208B3 protect on 0 protect on 1 protect on 2 flash_protect ON: from 0xBF040000 to 0xBF05FFFF protect on 4 protect on 5 *** Warning - bad CRC, using default environment ============================================ ZTE UBoot Version: 1.0.1 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM COMPONENT: 256Mbits DRAM BUS: 16BIT Total memory: 32 MBytes Date:Apr 7 2011 Time:19:55:01 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 freq = 384000000 MHZ ##### The CPU freq = 384 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes All PHY are used. Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. 0 last i charator of rootfs flash is � last i charator of rootfs flash is � last i charator of rootfs flash is � last i charator of rootfs flash is � last i charator of rootfs flash is � 3: System Boot system code via Flash. ## Booting image at bf080000 ... Image Name: Linux Kernel Image Created: 2011-07-15 2:04:58 UTC System Control Status = 0x00440000 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 6229952 Bytes = 5.9 MB Load Address: 80000000 Entry Point: 803b9000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 803b9000) ... ## Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (fanxy@localhost.localdomain) (gcc version 3.4.2) #60 PREEMPT Fri Jul 15 10:04:38 CST 2011 The CPU feqenuce set to 384 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock4 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = 10800000, status = 1100ff00 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00177000(1536000) CPU frequency 384.00 MHz Using 192.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 28420k/32768k available (3159k kernel code, 4348k reserved, 648k data, 128k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered (default) zhaoyong RALINK_REG_GPIOMODE=385 zhaoyong RALINK_REG_PIODIR=3 zhaoyong RALINK_REG_PIODIR_24_39=2182 zhaoyong RALINK_REG_PIODIR_40_51=e20 Ralink gpio driver initialized Enable Ralink GDMA Controller Module spidrv_major = 217 HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: loaded (max 8 devices) rdm_major = 254 PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 ralink flash device: 0x1000000 at 0xbf000000 Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 Ralink SoC physically mapped flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 7 MTD partitions on "Ralink SoC physically mapped flash": 0x00000000-0x00040000 : "Bootloader" 0x00040000-0x00060000 : "Config" 0x00060000-0x00080000 : "Factory" 0x00080000-0x001c0000 : "Kernel" 0x001c0000-0x007c0000 : "RootFS" 0x007c0000-0x008c0000 : "Jffs2" 0x008c0000-0x01000000 : "back" block2mtd: version $Revision: 1.1.1.1 $ Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1 usbcore: registered new interface driver usb-pcm drivers/usb/serial/usb-pcm.c: usb to pcm Driver: V2.4.20_uC0_1B12 nf_conntrack version 0.5.0 (256 buckets, 2048 max) IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone ipt_time loading TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 NET: Registered protocol family 17 NET: Registered protocol family 15 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> GDMA1_MAC_ADRH -- : 0x00000000 GDMA1_MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v2.00 64 rx/tx descriptors allocated, mtu = 1500! GDMA1_MAC_ADRH -- : 0x0000021e GDMA1_MAC_ADRL -- : 0x73830b61 PROC INIT OK! VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 128k freed init started: BusyBox v1.12.1 (2011-07-15 09:54:18 CST) starting pid 610, tty '': '/etc_ro/rcS' Algorithmics/MIPS FPU Emulator v1.5 devpts: called with bogus options cfg: no version for "struct_module" found: kernel tainted. Load cfg new driver... drivers/cfg/cfg_param.c 622 drivers/cfg/cfg_param.c 438 drivers/cfg/cfg_param.c 446 drivers/cfg/cfg_param.c 450 cfg driver : read cfg drivers/cfg/cfg_param.c 471 DDNSPassword=oamWiM 44444e5350617373776f72643d006f616d57694d drivers/cfg/cfg_param.c 500 drivers/cfg/cfg_param.c 438 drivers/cfg/cfg_param.c 446 drivers/cfg/cfg_param.c 450 cfg driver : read cfg drivers/cfg/cfg_param.c 471 SSID1=Instanet_4G_0B 53534944313d496e7374616e65745f34475f3042 drivers/cfg/cfg_param.c 500 drivers/cfg/cfg_param.c 438 drivers/cfg/cfg_param.c 446 drivers/cfg/cfg_param.c 450 cfg driver : read cfg drivers/cfg/cfg_param.c 471 0000000000000000000000000000000000000000 drivers/cfg/cfg_param.c 500 drivers/cfg/cfg_param.c 624 _______ _______ _______ /|__ | /| | /| _____| |/_ / / ||__ __| || |____/ // / |/_/| |_/ || _____| // /__ || | || |____/ ||_______| ||_| ||_______| |/______/ |/_/ |/______/ IX350 wifi_switchzhaoyong set gpio51 input e3f get gpio dir zhaoyong read gpio48 1c0 get gpio value wifi_switch i=1 ra0 no private ioctls. internet.sh zhaoyong open gpzhaoyong set gpio51 input e3f io success zhaoyong RALINK_REG_PIOFENA_40_51=100 write_gpiodir_40_51 fd=3 Password for 'admin' changed /sbin/internet.sh: line 257: wc: not found [: 0: unknown operand dwc_otg: config..done dwc_otg: version 2.72a 24-JUN-2008 DWC_otg: Core Release: 2.66a DWC_otg: Periodic Transfer Interrupt Enhancement - disabled DWC_otg: Multiprocessor Interrupt Enhancement - disabled DWC_otg: Using DMA mode DWC_otg: Device using Buffer DMA mode dwc_otg lm0: DWC OTG Controller dwc_otg lm0: new USB bus registered, assigned bus number 1 dwc_otg lm0: irq 18, io mem 0x00000000 DWC_otg: Init: Port Power? op_state=1 DWC_otg: Init: Power Port (0) usb usb1: --->>>[NDIS DEBUG]:enter generic_probe.drivers/usb/core/generic.c,161 usb usb1: --->>>[NDIS DEBUG]:enter choose_configuration.drivers/usb/core/generic.c,50 --->>>[NDIS DEBUG]:enter generic_probe.drivers/usb/core/generic.c,30 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected insmod: bridge.ko: module not found insmod: mii.ko: module not found insmod: raeth.ko: module not found phy_tx_ring0 = 019ad000, tx_ring0 = a19ad000, size: 16 bytes phy_tx_ring1 = 019ae000, tx_ring1 = a19ae000, size: 16 bytes phy_tx_ring2 = 019af000, tx_ring2 = a19af000, size: 16 bytes phy_tx_ring3 = 019b0000, tx_ring3 = a19b0000, size: 16 bytes phy_rx_ring = 0x00000000, rx_ring = 0x00000000 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 10000 ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device rmmod: rt2860v2_ap: No such file or directory rmmod: rt2860v2_sta: No such file or directory usb 1-1: new high speed USB device using dwc_otg and address 2 usb 1-1: --->>>[NDIS DEBUG]:enter generic_probe.drivers/usb/core/generic.c,161 usb 1-1: --->>>[NDIS DEBUG]:enter choose_configuration.drivers/usb/core/generic.c,50 --->>>[NDIS DEBUG]:enter generic_probe.drivers/usb/core/generic.c,30 usb 1-1: configuration #1 chosen from 1 choice rt2860v2_ap: module license 'unspecified' taints kernel. 2860 version : 2.0.0.0 (Jul 15 2011) === pAd = c15cb000, size = 110368 === rmmod: nf_nat_pptp: No such file or directory rmmod: nf_conntrack_pptp: No such file or directory rmmod: nf_nat_proto_gre: No such file or directory rmmod: nf_conntrack_proto_gre: No such file or directory RX DESC a1b7a000 size = 1024 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff 00 00 00 01 The primary RSNIE: c15cecee, len = 22 0x0000 : 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 0x0010 : 01 00 00 50 f2 02 zhaoyong isRadioOff==0 Main bssid = 02:1e:73:83:0b:61 The UUID Hex string is:2880288028801880a880021e73830b61 The UUID ASCII string is:28802880-2880-1880-a880-021e73830b61! 0x1300 = 00064380 insmod: 8021q.ko: module not found BusyBox v1.12.1 (2011-07-15 09:54:18 CST) multi-call binary Usage: ifconfig [-a] interface [address] ifconfig: ioctl 0x8913 failed: No such device brctl: bridge br0: No such device or address iptables v1.4.0rc1: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. device ra0 entered promiscuous mode ##### restore RT3052 to dump switch ##### switch reg write offset=14, value=5555 switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1001 switch reg write offset=4c, value=1 switch reg write offset=50, value=2001 switch reg write offset=70, value=ffffffff switch reg write offset=98, value=7f7f switch reg write offset=e4, value=0 device eth2 entered promiscuous mode br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Invalid argument br0: port 2(eth2) entering disabled state br0: port 1(ra0) entering disabled state br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state ifconfig: ioctl 0x8914 failed: Cannot assign requested address ifconfig: ioctl 0x8914 failed: Cannot assign requested address /sbin/lan.sh: line 63: hostname: not found Set: phy[0].reg[0] = 3900 Set: phy[0].reg[0] = 3100 Set: phy[1].reg[0] = 3900 Set: phy[1].reg[0] = 3100 Set: phy[2].reg[0] = 3900 Set: phy[2].reg[0] = 3100 Set: phy[3].reg[0] = 3900 Set: phy[3].reg[0] = 3100 Set: phy[4].reg[0] = 3900 Set: phy[4].reg[0] = 3100 ifconfig: ioctl 0x8913 failed: No such device killall rt2860apd 1>/dev/null 2>&1 iptables -F -t filter 1>/dev/null 2>&1 iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1 iptables -F macipport_filter 1>/dev/null 2>&1 iptables -D FORWARD -j web_filter 1>/dev/null 2>&1 iptables -F web_filter 1>/dev/null 2>&1 iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT iptables -P FORWARD ACCEPT iptables -t filter -N time_control 1>/dev/null 2>&1 iptables -t filter -N web_filter 1>/dev/null 2>&1 iptables -t filter -N macipport_filter 1>/dev/null 2>&1 iptables -t filter -A FORWARD -j time_control 1>/dev/null 2>&1 iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1 iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1 iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1 iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --set-mss 1360 timectrl -F time_control timefrom = iptables -t filter -F INPUT iptables -t filter -I INPUT -p tcp -d 192.168.0.1 --dport 80 -j ACCEPT iptables -t filter -A INPUT -i veth0 -p tcp --dport 80 -j DROP iptables -t filter -I INPUT -i veth0 -p icmp -j ACCEPT cfg save index:0 iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1 iptables -t nat -F port_forward 1>/dev/null 2>&1; iptables -t nat -X port_forward 1>/dev/null 2>&1 iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1 iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ 1>/dev/null 2>&1 iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1 iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1 iptables -t nat -I PREROUTING -j DNAT -i veth0 -p tcp --dport 9000 --to 192.168.0.1:80 iptables -t nat -A POSTROUTING -o veth0 -j MASQUERADE ip_table: set wan_name=veth0 echo 1 > /proc/sys/net/ipv4/ip_forward ntp.sh greenap.sh init ddns.sh route delete 239.255.255.250 1>/dev/null 2>&1 killall wscd 1>/dev/null 2>&1 ### WIMAXMGR ### ________________________wimaxmgr run_________________________ ### WIMAXMGR ### ____________________________MSGMGR_Main ### WIMAXMGR ### Creating wimaxmgr message queue success! msgid=0x8001 ### WIMAXMGR ### Load wimax firmware, enter wait... usbbcm_device_probe:subtype[1] = 0x000000ff usbbcm_device_probe:subtype[2] = 0x00000000 usbbcm_device_probe:subtype[4] = 0x00000000 usbbcm_device_probe:subtype[8] = 0x00000000 InitAdapter:Initialising Adapter = 0x80dc0000 InitAdapter:Adapter initialised usbbcm_device_probe:psIntfAdapter 0x80e76800 InterfaceAdapterInit:MODEM IS CONFIGURED TO HIGH_SPEED InterfaceAdapterInit:First RDM Chip ID 0xbece3301 InterfaceAdapterInit:usb dev registered register_control_device_interface:Got Major No: 251 create_worker_threads:Init Threads... open_firmware_file:Got file descriptor pointer of /lib/firmware/macxvi.cfg! beceem_parse_target_struct:AutoSyncup is Disabled beceem_parse_target_struct:Disabling autolink up beceem_parse_target_struct:DDR Setting: 3 beceem_parse_target_struct:Power Save Mode: 0 beceem_parse_target_struct:Enabling Auto Firmware Download beceem_parse_target_struct:MIPSConfig : 0x0 beceem_parse_target_struct:PMU MODE: 0 beceem_parse_target_struct:uiEEPROMFlag : 0x0 Bcm_kill_all_URBs:Cancelling All Submitted TX Urbs Bcm_kill_all_URBs:Cancelling All submitted Rx Urbs Bcm_kill_all_URBs:TCB: used- 0 cur-0 Bcm_kill_all_URBs:RCB: used- 0 cur-0 reset_card_proc:Reseting UMA-B usb 1-1: reset high speed USB device using dwc_otg and address 2 killall -9 wscd 1>/dev/null 2>&1 iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1 iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1 killall -q klogd killall -q syslogd syslogd -C256 1>/dev/null 2>&1 klogd 1>/dev/null 2>&1 killall -q zebra ddr_init:Register Count is =48 killall -q ripd InitCardAndDownloadFirmware:CFG file downloaded drivers/net/beceem_drv_5.2.7.3P2/Common/nvm.c:ReadMacAddressFromNVM:420:Buffer dump of size 0x6 in the HEX: 00 1E 73 83 0B 61 register_networkdev:Registering netdevice notifier register_networkdev:BCM Notifier got Registered bcm_notify_event:Register RefCount: 5 register_networkdev:Beceem Network device name is veth0! open_firmware_file:Got file descriptor pointer of /lib/firmware/macxvi200.bin! BcmFileDownload:Opened file is = /lib/firmware/macxvi200.bin and length =0x1ce998 to be downloaded at =0xbfc00000 BcmFileDownload:download start 6ad00697 zhaoyong RALINK_REG_PIOFENA_40_51=180 webs: Listening for HTTP requests at address 192.168.0.1 ra2880stop()...Done Free TX/RX Ring Memory! br0: port 2(eth2) entering disabled state cfg save index:0 InterfaceFileDownload:Got end of file! phy_tx_ring0 = 009af000, tx_ring0 = a09af000, size: 16 bytes phy_tx_ring1 = 009b0000, tx_ring1 = a09b0000, size: 16 bytes phy_tx_ring2 = 009b1000, tx_ring2 = a09b1000, size: 16 bytes phy_tx_ring3 = 009b2000, tx_ring3 = a09b2000, size: 16 bytes phy_rx_ring = 0x019b1000, rx_ring = 0xa19b1000 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 10000 br0: port 2(eth2) entering learning state InterfaceFileReadbackFromChip:Got end of file! BcmFileDownload:file download done at 6ad00d02 InitCardAndDownloadFirmware:BIN file downloaded device_run:Sending first interrupt URB down...... device_run:Got the mailbox interrupt ...Registering control interface... usbbcm_device_probe,[380],retval:0 usbcore: registered new interface driver usbbcm Initialised usbbcmDEVMONITOR_Main: get MSG_MONITOR_WIMAXDEV_UP message udhcpc (v1.12.1) started udhcp_run_script client_config.interface=veth0, client_config.script=/sbin/udhcpc.sh <7>ra0: no IPv6 routers present ### WIMAXMGR ### MSGMGR_Main: recieve a message from MSG_ID_WIMAXMGR ### WIMAXMGR ### HandleRvcMsg: receive MSG_MONITOR_WIMAXDEV_UP message dhcpc deconfig killall: dnsmasq: no process killed ####-DHCPC-####-->:UDHCPC:RELEASE main init. ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... br0: topology change detected, propagating br0: port 2(eth2) entering forwarding state ---- Starting D2Tech vPort. ---- ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### Wimax firmware up, run wimax entry manage! ### WIMAXMGR ### No factory config file ### WIMAXMGR ### EAP: method=13, userid=, pw=blank, submethod=26, subuserid=4761016 AddMIBEntry,[46],u16Offset:1240 ### WIMAXMGR ### enter BCMMIAC_Main ********** AddMIBEntry,[46],u16Offset:1240 ***************** BeceemWiMAX_GetStatisticsAddress,[2318],puiStatAddress:BFF16ABC ### WIMAXMGR ### CONNMGR_ReadRFEEPROMVersionRequest, 785 ### WIMAXMGR ### BCMCALLBACK_ReadRFEEPROMVersionResponse ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### CONNMGR_SSINFORequest, 71 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### CONNMGR_StatisticsGetRequest, 681 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### CONNMGR_StateMachine, 307, SM_EVENT_CONNCMDREC ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3405000 LastFreq=3415000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART CreateSoftTimer index 0 success: usTimerID = 3, ucFlag = 1, ulCurInterval = 25, ulNextInterval = 25, procCallBack = 0x00000000, args = 0x00000000. ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 0 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=br0: topology change detected, propagating br0: port 1(ra0) entering forwarding state 3402500 LastFreq=3417500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 1 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:dhcpc......leasefail. udhcp_run_script client_config.interface=veth0, client_config.script=/sbin/udhcpc.sh dhcpc leasefail ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3462500 LastFreq=3517500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART + RC_D2_REV=3 + D2_DIR=/usr/d2 + IF_ADDR=192.168.0.1 + mkdir -p /var/tmp/osal + mkdir -p /tmp/nv ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! + insmod /usr/d2/extern_osal_kernel_gpl.ko + insmod /usr/d2/osal_kernel.ko osal_module.c:35 OSAL module_init OK + insmod /usr/d2/ve_vtsp_hw.ko TIC: numTicFxs=1 numTicFxo=0 numTicAudio=0 + insmod /usr/d2/ve_vtsp_rt.ko ### WIMAXMGR ### Frequency Band 2 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT lkm.c 171: devname /dev/d2vtspr /dev/d2vtspr registered successfuly @ 250. + vapp -i 192.168.0.1 ======== vPort Release +D2Tech+ VPORT VPORT_R_1_5_66 ======== ZTE Technologies Unified Communication Products www.zte.com.cn voip_data.c:481 /tmp/nv/vport_cfg.xml doesn't exist, creat in now! voip_data.c 31: Write parameters to /tmp/nv/vport_cfg.xml voip_data.c:496 /tmp/nv/vport_cfg.xml exist! voip_data.c:506 Now we do _VAPP_profileRead() to parse vapp_init.c:506 - hostname_ptr=192.168.0.1 vapp_init.c:531 VAPP hostname 192.168.0.1 ('192.168.0.1') vapp_init.c:533 VAPP hostname 192.168.0.1 (hbo c0a80001) vapp_init.c: vTSP version +D2Tech+ VTSP VPORT_R_1_5_109, (R-1-4-0) ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3465000 LastFreq=3515000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART vapp_init.c: 1229 UA 0 is configured with these params: Hostname: 192.168.0.1 (hbo c0a80001) HostAddr: 192.168.0.1 Authname: 2940100 Password: dilbert Domain: test.d2tech.com Realm: test.d2tech.com Registrar: Proxy : Username[0]: 2940100 Dname[0]: 2940100 vhw.c VHW_init: VHW_NUM_PCM_CH = 1 _vhw.c _VHW_pcmOpen: SYSTEM_CLKCFG1 = 0x428C7 _vhw.c _VHW_pcmOpen: SYSTEM_GPIOMODE = 0x391 _vhw.c _VHW_pcmRegSetup: PCM_PCMCFG = 0x43000000 _vhw.c _VHW_pcmRegSetup: PCM_GLBCFG = 0x440000 _vhw.c _VHW_pcmRegSetup: PCM_CH0_CFG = 0x0 _vhw.c _VHW_pcmRegSetup: PCM_CH1_CFG = 0x0 _vhw.c _VHW_pcmStart: PCM_GLBCFG = 0xC0440000 _vhw.c _VHW_pcmEnable: PCM_GLBCFG = 0xC0440101 Revision Id 0x1 on channel 0 Si3217x_Init 897 - chip type = 0x14, rev = 1 VBAT Up = 61.275 v Si3217x PCMStart tic.c 165 TIC_initInfc(chan=0,infc=53760) vapp_vtsp.c: VTSP_getVersion reports v1.4.0 vapp_init.c, 413: gainrx = 0, gaintx = -20 vapp_sip_task.c 240: msgget Phone_VOIP_Msg_Id success ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 3 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3562500 LastFreq=3597500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART D2 Technologies, Inc. _ _ __ / | '/ /_ _ /_ _ _ /_ _ ._ _ /_.'/_ //_'/_ / // //_///_//_///_'_\ _/ Unified Communication Products www.d2tech.com +D2Tech+ VTSP_RT VPORT_R_1_5_109 +D2Tech+ VTSP_RT VPORT_R_1_5_109 +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ nse M24KEC4_B_1_1-nse_1_2 src-svn: 225 d2tools-svn: 3454 +D2Tech+ plc M24KEC4_B_1_1-plc_1_1 src-svn: 225 d2tools-svn: 3454 +D2Tech+ tone M24KEC4_B_1_1-tone_1_2 src-svn: 225 d2tools-svn: 3454 +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ +D2Tech+ vapp_sip_fsm.c 1156: RELEASE action! ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 4 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3565000 LastFreq=3595000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART starting pid 1379, tty '/dev/ttyS1': '/bin/sh' waiting the time msg! |||||||||||||| BusyBox v1.12.1 (2011-07-15 09:54:18 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. -> fac Server start wait... start accept...... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### CONNMGR_NetworkSelectMethod, 481 ### WIMAXMGR ### INFOMGR_SelectBS ### WIMAXMGR ### no BS in all frequency band ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3405000 LastFreq=3415000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 0 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3402500 LastFreq=3417500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 1 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3462500 LastFreq=3517500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 2 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3465000 LastFreq=3515000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 3 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3562500 LastFreq=3597500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:dhcpc......leasefail. udhcp_run_script client_config.interface=veth0, client_config.script=/sbin/udhcpc.sh dhcpc leasefail ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 4 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3565000 LastFreq=3595000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### CONNMGR_NetworkSelectMethod, 481 ### WIMAXMGR ### INFOMGR_SelectBS ### WIMAXMGR ### no BS in all frequency band ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3405000 LastFreq=3415000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 0 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3402500 LastFreq=3417500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 1 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3462500 LastFreq=3517500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 2 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3465000 LastFreq=3515000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 3 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3562500 LastFreq=3597500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 4 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3565000 LastFreq=3595000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### CONNMGR_NetworkSelectMethod, 481 ### WIMAXMGR ### INFOMGR_SelectBS ### WIMAXMGR ### no BS in all frequency band ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3405000 LastFreq=3415000 NextFreqStep=10000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 0 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3402500 LastFreq=3417500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART ####-DHCPC-####-->:If timeout dropped to zero, time to become active. ####-DHCPC-####-->:switch (state) ====state = 0 ####-DHCPC-####-->:dhcpc......leasefail. udhcp_run_script client_config.interface=veth0, client_config.script=/sbin/udhcpc.sh dhcpc leasefail ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ### WIMAXMGR ### INFOMGR_Update_BSInfo:num_of_bs=0 ### WIMAXMGR ### INFOMGR_Update_BSInfo: no bs searched! ### WIMAXMGR ### Frequency Band 1 scan complete! ### WIMAXMGR ### ***************SM_STATUS_INIT -> ### WIMAXMGR ### SEARCH NEW BS ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, 106 ### WIMAXMGR ### Before enter if ,g_sys_info.ScanFreqMode = 0 ### WIMAXMGR ### g_sys_info.ChannelPlanNum = 6 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, g_sys_info.BandwidthList.NumOfBwsToScan = 2 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW0=5000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, BW1=10000 ### WIMAXMGR ### CONNMGR_NetworkSearchRequest, FirstFreq=3462500 LastFreq=3517500 NextFreqStep=5000 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1097, result=0 ### WIMAXMGR ### CONNMGR_SendWiMAXMessage, 1101, SendWiMAXMessage SUCCESS ### WIMAXMGR ### SearchResponse: SUCCESS ### WIMAXMGR ### ***************SM_STATUS_WAITSCAN_PART -> wifi_unload.sh ####-DHCPC-####-->:errno == EINTR..continue. ####-DHCPC-####-->:Main event loop. select() waits on signal pipe and possibly on sockfd. ####-DHCPC-####-->:Waiting on select... ####-DHCPC-####-->:If timeout dropped to zero, time to become active. Received SIGTERM br0: port 2(eth2) entering disabled state br0: port 1(ra0) entering disabled state device eth2 left promiscuous mode br0: port 2(eth2) entering disabled state device ra0 left promiscuous mode br0: port 1(ra0) entering disabled state ra2880stop()...Done Free TX/RX Ring Memory! GDMA1_MAC_ADRH -- : 0x0000021e GDMA1_MAC_ADRL -- : 0x73830b61 phy_tx_ring0 = 01af1000, tx_ring0 = a1af1000, size: 16 bytes phy_tx_ring1 = 01b11000, tx_ring1 = a1b11000, size: 16 bytes phy_tx_ring2 = 01b57000, tx_ring2 = a1b57000, size: 16 bytes phy_tx_ring3 = 01b54000, tx_ring3 = a1b54000, size: 16 bytes phy_rx_ring = 0x009b3000, rx_ring = 0xa09b3000 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 10000 -> --- Fin del código --- Cuando iniciamos por el puerto serie, hay una serie de mensajes repetitivos sobre wimax intentando conectar, para parar wimax y poder trabajar cómodamente en la consola, ponemos: --- Código: ---wifi_unload.sh --- Fin del código --- Así paramos el wifi, el router se encuentra en 192.168.0.1 Comandos: --- Código: ----> BeceemWiMaxApp halt pppoe.sh RemoteProxy.cfg ifconfig pptp TestBeceemCalAPI igmpproxy pptp.sh VPN igmpproxy.sh ps [ inadyn qos_run [[ init radvd ash insmod ralink_init ated internet.sh reboot automount.sh ip reg awk ipaddr ripd brctl iplink rm busybox iproute rmmod cal_tgtxvi020 iprule route cat iptables rpcapd cfg iptunnel rt2860apd chat iwconfig sed chkSvr iwevent sh chmod iwgetid sigmon chpasswd iwlist sleep chpasswd.sh iwpriv statedect close iwspy switch comgt kill sync config-3g-ppp.sh killall syslogd config-dns.sh klogd tc config-igmpproxy.sh l2tp-control tcpdump config-l2tp.sh l2tp.sh telnetd config-pppoe.sh l2tpd test config-pptp.sh lan.sh tftp config-udhcpd.sh lld2d tftp_ftp_up config-vlan.sh logger tftpd config.sh login timectrl cp logread top d2restart.sh ls touch d2start.sh lsmod tr date macgo udhcpc ddns.sh mii_mgr udhcpc.sh dnsmasq mkdir udhcpc_vpn.sh echo mkfs.jffs udhcpd egrep mkfs.jffs2 uimlock erase mknod upnp_xml.sh eraseall mount upnpd ethtool msntp uptime expr mtd_write vapp facSvr mv vconfig firewall.sh nat.sh vi flash net2tty_dload.sh vpn-passthru.sh free net2tty_qxdm.sh wan.sh ftpget ntp.sh wdashn ftpput ntpclient wdhcpc global.sh nvram_daemon wifi_unload.sh goahead nvram_get wimax_pc gpio nvram_set wimaxmgr gpiotest openssl wscd greenap.sh ping zebra grep poweroff zte_wlan.sh --- Fin del código --- --- Código: ----> help Built-in commands: ------------------- . : break cd chdir continue eval exec exit export false hash help local pwd read readonly return set shift source times trap true type ulimit umask unset wait --- Fin del código --- Cpuinfo: --- Código: ----> cat /proc/cpuinfo system type : Ralink SoC processor : 0 cpu model : MIPS 24K V4.12 BogoMIPS : 255.48 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes ASEs implemented : mips16 dsp VCED exceptions : not available VCEI exceptions : not available --- Fin del código --- /dev/ --- Código: ----> ls /dev/ video0 ttyS0 ram0 mtdblock6 mtd5ro mtd1 flash1 urandom tarang ram mtdblock5 mtd5 mtd0ro flash0 ttyp1 swnat0 ptyp1 mtdblock4 mtd4ro mtd0 console ttyp0 spiS0 ptyp0 mtdblock3 mtd4 mem acl0 ttyUSB3 rdm0 pts mtdblock2 mtd3ro kmem ac0 ttyUSB2 random ptmx mtdblock1 mtd3 i2cM0 PCM ttyUSB1 ram3 ppp mtdblock0 mtd2ro hwnat0 I2S ttyUSB0 ram2 null mtd6ro mtd2 gpio ttyS1 ram1 mtr0 mtd6 mtd1ro flash2 --- Fin del código --- Particiones de la flash: --- Código: ----> cat /proc/partitions major minor #blocks name 31 0 256 mtdblock0 31 1 128 mtdblock1 31 2 128 mtdblock2 31 3 1280 mtdblock3 31 4 6144 mtdblock4 31 5 1024 mtdblock5 31 6 7424 mtdblock6 --- Fin del código --- --- Código: ----> cat /proc/mtd dev: size erasesize name mtd0: 00040000 00020000 "Bootloader" mtd1: 00020000 00020000 "Config" mtd2: 00020000 00020000 "Factory" mtd3: 00140000 00020000 "Kernel" mtd4: 00600000 00020000 "RootFS" mtd5: 00100000 00020000 "Jffs2" mtd6: 00740000 00020000 "back" --- Fin del código --- Otras cosas que pueden ser de interés: --- Código: ----> cat /proc/iomem 00000000-01ffffff : System RAM 00000000-00315ccb : Kernel code 00315ccc-003b80bf : Kernel data 101c0000-101fffff : lm0 -> cat /proc/ioports b0000500-b000051f : serial b0000c00-b0000c1f : serial -> cat /proc/devices Character devices: 1 mem 2 pty 3 ttyp 4 ttyS 5 /dev/tty 5 /dev/console 5 /dev/ptmx 10 misc 13 input 21 sg 90 mtd 108 ppp 128 ptm 136 pts 180 usb 188 ttyUSB 189 usb_device 200 flash0 217 spiS0 250 d2vtspr 251 tarang 252 gpio 253 usb_endpoint 254 rdm0 Block devices: 7 loop 31 mtdblock -> cat /proc/interrupts CPU0 3: 243 Surfboard eth2 5: 204650 Surfboard timer 6: 0 Surfboard ralink_gpio 7: 155064 Surfboard Ralink_DMA 11: 0 Surfboard Ralink_ESW 12: 6348 Surfboard serial 18: 6598439 Surfboard dwc_otg, dwc_otg_hcd:usb1 ERR: 0 --- Fin del código --- Como vemos en los comandos, hay uno que nos irá de perlas para el backup de la flash: ftpput Para ello, montamos un servidor ftp en nuestro ordenador local, por ejemplo en: 192.168.0.10 y hacemos el backup de la flash de la siguiente forma: --- Código: ---ftpput 192.168.0.10 mtdblock0 /dev/mtdblock0 -u USER -p PASS ftpput 192.168.0.10 mtdblock1 /dev/mtdblock1 -u USER -p PASS ftpput 192.168.0.10 mtdblock2 /dev/mtdblock2 -u USER -p PASS ftpput 192.168.0.10 mtdblock3 /dev/mtdblock3 -u USER -p PASS ftpput 192.168.0.10 mtdblock4 /dev/mtdblock4 -u USER -p PASS ftpput 192.168.0.10 mtdblock5 /dev/mtdblock5 -u USER -p PASS ftpput 192.168.0.10 mtdblock6 /dev/mtdblock6 -u USER -p PASS --- Fin del código --- Donde USER y PASS son los usuarios para ftp. Tambien se puede hacer de forma anonima, en este caso no pondremos los parámetros -u y -p Para obtener las contraseñas del wifi y la web: --- Código: ---cat /etc_rw/param/inic_param --- Fin del código --- Es el primer router al que le pongo OpenWrt sin estar soportado oficialmente, así que seguramente habrá muchas cosas que pulir ^-^ continuará. |
mekkon:
Dejo unas cuantas fotillos más: Wimax: Editado por jar229 para redimensionar las imágenes (descuadraban totalmente el hilo). |
mekkon:
Y este es el log de arranque de la primera versión de openwrt funcionando en este router, esta basado en Barrier Breaker: --- Código: ---[ 0.000000] Linux version 3.10.69 (xonom@xonom) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44382) ) #5 Thu Feb 12 21:20:34 CET 2015 [ 0.000000] SoC Type: Ralink RT3052 id:1 rev:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is ZTE IX350 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 80292a10, node_mem_map 81003260 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8192 pages, LIFO batch:0 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=0000000c [ 0.000000] Readback ErrCtl register=0000000c [ 0.000000] Memory: 29360k/32768k available (2173k kernel code, 3408k reserved, 546k data, 156k init, 0k highmem) [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 384MHz [ 0.070000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952) [ 0.070000] pid_max: default: 4096 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] pinctrl core: initialized pinctrl subsystem [ 0.090000] NET: Registered protocol family 16 [ 0.100000] rt2880-pinmux pinctrl.1: try to register 52 pins ... [ 0.100000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux [ 0.100000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux [ 0.100000] pinctrl core: add 7 pinmux maps [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 7 for sdram [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 1 for spi [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 0 for i2c [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 4 for jtag [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 6 for rgmii [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 5 for mdio [ 0.100000] rt2880-pinmux pinctrl.1: found group selector 2 for uartf [ 0.100000] rt2880-pinmux pinctrl.1: request pin 24 (io24) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 25 (io25) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 26 (io26) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 27 (io27) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 28 (io28) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 29 (io29) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 30 (io30) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 31 (io31) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 32 (io32) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 33 (io33) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 34 (io34) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 35 (io35) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 36 (io36) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 37 (io37) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 38 (io38) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 39 (io39) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 3 (io3) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 6 (io6) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 1 (io1) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 2 (io2) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 17 (io17) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 18 (io18) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 19 (io19) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 20 (io20) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 21 (io21) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 40 (io40) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 41 (io41) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 42 (io42) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 43 (io43) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 44 (io44) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 45 (io45) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 46 (io46) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 47 (io47) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 48 (io48) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 49 (io49) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 50 (io50) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 51 (io51) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 22 (io22) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 23 (io23) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 7 (io7) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 8 (io8) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 10 (io10) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 11 (io11) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pinctrl.1 [ 0.100000] rt2880-pinmux pinctrl.1: failed to lookup the sleep state [ 0.130000] bio: create slab <bio-0> at 0 [ 0.130000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.140000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.150000] Switching to clocksource MIPS [ 0.160000] NET: Registered protocol family 2 [ 0.160000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.170000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.170000] TCP: Hash tables configured (established 512 bind 512) [ 0.180000] TCP: reno registered [ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.190000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.190000] NET: Registered protocol family 1 [ 0.200000] rt-timer 10000100.timer: maximum frequncy is 7812Hz [ 0.210000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT [ 0.210000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.220000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.230000] msgmni has been set to 57 [ 0.230000] io scheduler noop registered [ 0.240000] io scheduler deadline registered (default) [ 0.240000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.250000] serial8250 serial8250: no of_node; not parsing pinctrl DT [ 0.250000] pinctrl core: add 1 pinmux maps [ 0.250000] rt2880-pinmux pinctrl.1: found group selector 3 for uartlite [ 0.250000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for 10000c00.uartlite [ 0.250000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for 10000c00.uartlite [ 0.250000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.260000] console [ttyS0] enabled, bootconsole disabled [ 0.280000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101 [ 0.290000] NOR chip too large to fit in mapping. Attempting to cope... [ 0.290000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.300000] Amd/Fujitsu Extended Query version 1.3. [ 0.300000] number of CFI chips: 1 [ 0.310000] Reducing visibility of 16384KiB chip to 8192KiB [ 0.310000] 4 ofpart partitions found on MTD device 1f000000.cfi [ 0.320000] Creating 4 MTD partitions on "1f000000.cfi": [ 0.330000] 0x000000000000-0x000000040000 : "u-boot" [ 0.330000] 0x000000040000-0x000000060000 : "u-boot-env" [ 0.340000] 0x000000060000-0x000000080000 : "factory" [ 0.350000] 0x000000080000-0x000001000000 : "firmware" [ 0.360000] mtd: partition "firmware" extends beyond the end of device "1f000000.cfi" -- size truncated to 0x780000 [ 0.370000] 0x0000001759cc-0x000000800000 : "rootfs" [ 0.380000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.390000] mtd: device 4 (rootfs) set to be root filesystem [ 0.400000] mtd: partition "rootfs_data" created automatically, ofs=0x640000, len=0x1c0000 [ 0.410000] 0x000000640000-0x000000800000 : "rootfs_data" [ 0.420000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.430000] rt2880_wdt 10000120.watchdog: Initialized [ 0.440000] zram: Created 1 device(s) ... [ 0.450000] TCP: cubic registered [ 0.450000] NET: Registered protocol family 17 [ 0.450000] 8021q: 802.1Q VLAN Support v1.8 [ 0.470000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.480000] Freeing unused kernel memory: 156K (802a9000 - 802d0000) [ 3.390000] usbcore: registered new interface driver usbfs [ 3.400000] usbcore: registered new interface driver hub [ 3.400000] usbcore: registered new device driver usb [ 3.470000] SCSI subsystem initialized [ 3.490000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.490000] ehci-platform: EHCI generic platform driver [ 3.500000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.520000] dwc_otg: version 2.72a 24-JUN-2008 [ 3.530000] dwc_otg: Core Release: 2.66a [ 3.730000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled [ 3.740000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled [ 3.740000] dwc_otg: Using DMA mode [ 3.750000] dwc_otg: Device using Buffer DMA mode [ 3.750000] dwc_otg 101c0000.otg: DWC OTG Controller [ 3.760000] dwc_otg 101c0000.otg: new USB bus registered, assigned bus number 1 [ 3.760000] dwc_otg 101c0000.otg: irq 26, io mem 0x101c0000 [ 3.770000] dwc_otg: Init: Port Power? op_state=1 [ 3.770000] dwc_otg: Init: Power Port (0) [ 3.780000] usb usb1: no of_node; not parsing pinctrl DT [ 3.780000] hub 1-0:1.0: no of_node; not parsing pinctrl DT [ 3.780000] hub 1-0:1.0: USB hub found [ 3.780000] hub 1-0:1.0: 1 port detected [ 3.800000] usbcore: registered new interface driver usb-storage [ 4.400000] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 5.020000] usb 1-1: no of_node; not parsing pinctrl DT [ 5.030000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 8.710000] jffs2: notice: (241) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 22 of xref (0 dead, 3 orphan) found. [ 8.750000] jffs2: notice: (238) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 22 of xref (0 dead, 3 orphan) found. [ 12.380000] NET: Registered protocol family 10 [ 12.420000] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 12.470000] nf_conntrack version 0.5.0 (461 buckets, 1844 max) [ 12.490000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 12.550000] u32 classifier [ 12.550000] input device check on [ 12.560000] Actions configured [ 12.580000] Mirror/redirect action on [ 12.620000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2 [ 12.620000] Backport generated by backports.git backports-20141023-2-g4ff890b [ 12.640000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 12.730000] usbcore: registered new interface driver usblp [ 12.850000] xt_time: kernel timezone is -0000 [ 12.910000] cfg80211: Calling CRDA to update world regulatory domain [ 12.920000] cfg80211: World regulatory domain updated: [ 12.920000] cfg80211: DFS Master region: unset [ 12.930000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 12.940000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.940000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.950000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 12.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.970000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 12.980000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 12.990000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.990000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 13.110000] PPP generic driver version 2.4.2 [ 13.120000] NET: Registered protocol family 24 [ 13.180000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected [ 13.190000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected [ 13.200000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 24.980000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 25.010000] device eth0.1 entered promiscuous mode [ 25.010000] device eth0 entered promiscuous mode [ 25.030000] br-lan: port 1(eth0.1) entered forwarding state [ 25.030000] br-lan: port 1(eth0.1) entered forwarding state [ 27.030000] br-lan: port 1(eth0.1) entered forwarding state [ 51.050000] rt305x-esw 10110000.esw: link changed 0x00 [ 53.610000] rt305x-esw 10110000.esw: link changed 0x01 [ 54.260000] rt305x-esw 10110000.esw: link changed 0x00 [ 61.920000] rt305x-esw 10110000.esw: link changed 0x01 [ 62.590000] rt305x-esw 10110000.esw: link changed 0x00 [ 64.270000] rt305x-esw 10110000.esw: link changed 0x01 [ 110.140000] rt305x-esw 10110000.esw: link changed 0x00 [ 113.690000] rt305x-esw 10110000.esw: link changed 0x01 [ 123.180000] rt305x-esw 10110000.esw: link changed 0x00 [ 123.220000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 123.240000] device wlan0 entered promiscuous mode [ 123.310000] br-lan: port 2(wlan0) entered forwarding state [ 123.310000] br-lan: port 2(wlan0) entered forwarding state [ 123.320000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 124.780000] rt305x-esw 10110000.esw: link changed 0x01 [ 125.310000] br-lan: port 2(wlan0) entered forwarding state [ 134.540000] rt305x-esw 10110000.esw: link changed 0x00 --- Fin del código --- --- Código: ---Thu Feb 12 20:48:59 2015 kern.info kernel: [ 4.400000] usb 1-1: new high-speed USB device number 2 using dwc_otg Thu Feb 12 20:48:59 2015 kern.debug kernel: [ 5.020000] usb 1-1: no of_node; not parsing pinctrl DT Thu Feb 12 20:48:59 2015 kern.info kernel: [ 5.030000] 8021q: adding VLAN 0 to HW filter on device eth0 Thu Feb 12 20:48:59 2015 kern.notice kernel: [ 8.710000] jffs2: notice: (241) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 22 of xref (0 dead, 3 orphan) found. Thu Feb 12 20:48:59 2015 kern.notice kernel: [ 8.750000] jffs2: notice: (238) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 22 of xref (0 dead, 3 orphan) found. Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.380000] NET: Registered protocol family 10 Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.420000] NTFS driver 2.1.30 [Flags: R/O MODULE]. Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.470000] nf_conntrack version 0.5.0 (461 buckets, 1844 max) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.490000] ip6_tables: (C) 2000-2006 Netfilter Core Team Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.550000] u32 classifier Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.550000] input device check on Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.560000] Actions configured Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.580000] Mirror/redirect action on Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.620000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2 Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.620000] Backport generated by backports.git backports-20141023-2-g4ff890b Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.640000] ip_tables: (C) 2000-2006 Netfilter Core Team Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.730000] usbcore: registered new interface driver usblp Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.850000] xt_time: kernel timezone is -0000 Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.910000] cfg80211: Calling CRDA to update world regulatory domain Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.920000] cfg80211: World regulatory domain updated: Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.920000] cfg80211: DFS Master region: unset Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.930000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.940000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.940000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.950000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.970000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.980000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.990000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 12.990000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) Thu Feb 12 20:48:59 2015 kern.info kernel: [ 13.110000] PPP generic driver version 2.4.2 Thu Feb 12 20:48:59 2015 kern.info kernel: [ 13.120000] NET: Registered protocol family 24 Thu Feb 12 20:48:59 2015 kern.info kernel: [ 13.180000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected Thu Feb 12 20:48:59 2015 kern.info kernel: [ 13.190000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected Thu Feb 12 20:48:59 2015 kern.debug kernel: [ 13.200000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' Thu Feb 12 20:49:02 2015 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly Thu Feb 12 20:49:02 2015 user.err syslog: /dev/mtdblock5 is already mounted Thu Feb 12 20:49:02 2015 user.emerg syslog: block: /dev/mtdblock5 is already mounted Thu Feb 12 20:49:04 2015 authpriv.info dropbear[822]: Not backgrounding Thu Feb 12 20:49:06 2015 user.info syslog: module is already loaded - xt_multiport Thu Feb 12 20:49:06 2015 kern.emerg already loaded - xt_multiport Thu Feb 12 20:49:06 2015 user.info syslog: module is already loaded - xt_comment Thu Feb 12 20:49:06 2015 kern.emerg already loaded - xt_comment Thu Feb 12 20:49:06 2015 user.info syslog: module is already loaded - xt_length Thu Feb 12 20:49:06 2015 kern.emerg already loaded - xt_length Thu Feb 12 20:49:07 2015 kern.info kernel: [ 24.980000] 8021q: adding VLAN 0 to HW filter on device eth0 Thu Feb 12 20:49:07 2015 kern.info kernel: [ 25.010000] device eth0.1 entered promiscuous mode Thu Feb 12 20:49:07 2015 kern.info kernel: [ 25.010000] device eth0 entered promiscuous mode Thu Feb 12 20:49:07 2015 kern.info kernel: [ 25.030000] br-lan: port 1(eth0.1) entered forwarding state Thu Feb 12 20:49:07 2015 kern.info kernel: [ 25.030000] br-lan: port 1(eth0.1) entered forwarding state Thu Feb 12 20:49:07 2015 daemon.notice netifd: Interface 'lan' is enabled Thu Feb 12 20:49:07 2015 daemon.notice netifd: Interface 'lan' is setting up now Thu Feb 12 20:49:07 2015 daemon.notice netifd: Interface 'lan' is now up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'loopback' is enabled Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'loopback' is setting up now Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'loopback' is now up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'wan' is enabled Thu Feb 12 20:49:08 2015 daemon.notice netifd: Network device 'eth0' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: VLAN 'eth0.2' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'wan' has link connectivity Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'wan' is setting up now Thu Feb 12 20:49:08 2015 daemon.notice netifd: VLAN 'eth0.1' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: VLAN 'eth0.1' link is down Thu Feb 12 20:49:08 2015 daemon.notice netifd: VLAN 'eth0.1' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Bridge 'br-lan' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'lan' has link connectivity Thu Feb 12 20:49:08 2015 daemon.notice netifd: Network device 'lo' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'loopback' has link connectivity Thu Feb 12 20:49:08 2015 daemon.notice netifd: VLAN 'eth0.2' link is down Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'wan' has link connectivity loss Thu Feb 12 20:49:08 2015 daemon.notice netifd: VLAN 'eth0.2' link is up Thu Feb 12 20:49:08 2015 daemon.notice netifd: Interface 'wan' has link connectivity Thu Feb 12 20:49:09 2015 daemon.notice netifd: wan (982): udhcpc (v1.22.1) started Thu Feb 12 20:49:09 2015 daemon.notice netifd: radio0 (941): command failed: Numerical result out of range (-34) Thu Feb 12 20:49:09 2015 daemon.notice netifd: wan (982): Sending discover... Thu Feb 12 20:49:09 2015 kern.info kernel: [ 27.030000] br-lan: port 1(eth0.1) entered forwarding state Thu Feb 12 20:49:10 2015 user.notice firewall: Reloading firewall due to ifup of lan (br-lan) Thu Feb 12 20:49:10 2015 user.info syslog: module is already loaded - xt_multiport Thu Feb 12 20:49:10 2015 kern.emerg already loaded - xt_multiport Thu Feb 12 20:49:10 2015 user.info syslog: module is already loaded - xt_comment Thu Feb 12 20:49:10 2015 kern.emerg already loaded - xt_comment Thu Feb 12 20:49:10 2015 user.info syslog: module is already loaded - xt_length Thu Feb 12 20:49:10 2015 kern.emerg already loaded - xt_length Thu Feb 12 20:49:12 2015 daemon.notice netifd: wan (982): Sending discover... Thu Feb 12 20:49:16 2015 daemon.notice netifd: wan (982): Sending discover... Thu Feb 12 20:49:17 2015 daemon.info dnsmasq[1240]: started, version 2.71 cachesize 150 Thu Feb 12 20:49:17 2015 daemon.info dnsmasq[1240]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC Thu Feb 12 20:49:17 2015 daemon.info dnsmasq-dhcp[1240]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h Thu Feb 12 20:49:17 2015 daemon.info dnsmasq[1240]: using local addresses only for domain lan Thu Feb 12 20:49:17 2015 daemon.warn dnsmasq[1240]: no servers found in /tmp/resolv.conf.auto, will retry Thu Feb 12 20:49:17 2015 daemon.info dnsmasq[1240]: read /etc/hosts - 1 addresses Thu Feb 12 20:49:17 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/dhcp - 1 addresses Thu Feb 12 20:49:17 2015 daemon.info dnsmasq-dhcp[1240]: read /etc/ethers - 0 addresses Thu Feb 12 20:49:18 2015 user.emerg syslog: configfile: stat (/etc/collectd/conf.d) failed: No such file or directory Thu Feb 12 20:49:18 2015 user.emerg syslog: Could not find plugin iptables. Thu Feb 12 20:49:18 2015 user.emerg syslog: Could not find plugin tcpconns. Thu Feb 12 20:49:18 2015 user.emerg syslog: Found a configuration for the `tcpconns' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:18 2015 user.emerg syslog: Found a configuration for the `tcpconns' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:18 2015 user.emerg syslog: Found a configuration for the `tcpconns' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:18 2015 user.emerg syslog: Could not find plugin conntrack. Thu Feb 12 20:49:19 2015 user.emerg syslog: rrdtool plugin: RRASingle = true: creating only AVERAGE RRAs Thu Feb 12 20:49:19 2015 user.notice upnp daemon: external interface not found, not starting Thu Feb 12 20:49:19 2015 user.emerg syslog: Could not find plugin processes. Thu Feb 12 20:49:19 2015 user.emerg syslog: Found a configuration for the `processes' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:19 2015 user.emerg syslog: Found a configuration for the `processes' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:19 2015 user.emerg syslog: Found a configuration for the `processes' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:19 2015 user.emerg syslog: Could not find plugin olsrd. Thu Feb 12 20:49:19 2015 user.emerg syslog: Found a configuration for the `olsrd' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:19 2015 user.emerg syslog: Found a configuration for the `olsrd' plugin, but the plugin isn't loaded or didn't register a configuration callback. Thu Feb 12 20:49:19 2015 user.emerg syslog: Could not find plugin memory. Thu Feb 12 20:49:19 2015 user.emerg syslog: Could not find plugin uptime. Thu Feb 12 20:49:19 2015 user.emerg syslog: Could not find plugin cpu. Thu Feb 12 20:49:20 2015 daemon.info dnsmasq-dhcp[1240]: DHCPDISCOVER(br-lan) c8:60:00:5f:c4:af Thu Feb 12 20:49:20 2015 daemon.info dnsmasq-dhcp[1240]: DHCPOFFER(br-lan) 192.168.1.241 c8:60:00:5f:c4:af Thu Feb 12 20:49:20 2015 daemon.info dnsmasq-dhcp[1240]: DHCPREQUEST(br-lan) 192.168.1.241 c8:60:00:5f:c4:af Thu Feb 12 20:49:20 2015 daemon.info dnsmasq-dhcp[1240]: DHCPACK(br-lan) 192.168.1.241 c8:60:00:5f:c4:af xonom Thu Feb 12 20:49:21 2015 user.emerg syslog: - init complete - Thu Feb 12 20:49:33 2015 kern.info kernel: [ 51.050000] rt305x-esw 10110000.esw: link changed 0x00 Thu Feb 12 20:49:36 2015 kern.info kernel: [ 53.610000] rt305x-esw 10110000.esw: link changed 0x01 Thu Feb 12 20:49:37 2015 kern.info kernel: [ 54.260000] rt305x-esw 10110000.esw: link changed 0x00 Thu Feb 12 20:49:44 2015 kern.info kernel: [ 61.920000] rt305x-esw 10110000.esw: link changed 0x01 Thu Feb 12 20:49:44 2015 daemon.info dnsmasq-dhcp[1240]: DHCPREQUEST(br-lan) 192.168.1.241 c8:60:00:5f:c4:af Thu Feb 12 20:49:44 2015 daemon.info dnsmasq-dhcp[1240]: DHCPACK(br-lan) 192.168.1.241 c8:60:00:5f:c4:af xonom Thu Feb 12 20:49:45 2015 kern.info kernel: [ 62.590000] rt305x-esw 10110000.esw: link changed 0x00 Thu Feb 12 20:49:47 2015 kern.info kernel: [ 64.270000] rt305x-esw 10110000.esw: link changed 0x01 Thu Feb 12 20:49:51 2015 daemon.info dnsmasq-dhcp[1240]: DHCPREQUEST(br-lan) 192.168.1.241 c8:60:00:5f:c4:af Thu Feb 12 20:49:51 2015 daemon.info dnsmasq-dhcp[1240]: DHCPACK(br-lan) 192.168.1.241 c8:60:00:5f:c4:af xonom Thu Feb 12 20:49:52 2015 daemon.warn odhcpd[780]: DHCPV6 SOLICIT IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::879/128 Thu Feb 12 20:49:53 2015 daemon.info dnsmasq[1240]: read /etc/hosts - 1 addresses Thu Feb 12 20:49:53 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/odhcpd - 0 addresses Thu Feb 12 20:49:53 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/dhcp - 1 addresses Thu Feb 12 20:49:53 2015 daemon.info dnsmasq-dhcp[1240]: read /etc/ethers - 0 addresses Thu Feb 12 20:49:53 2015 daemon.warn odhcpd[780]: DHCPV6 REQUEST IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::879/128 Thu Feb 12 20:49:54 2015 daemon.info dnsmasq[1240]: read /etc/hosts - 1 addresses Thu Feb 12 20:49:54 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/odhcpd - 1 addresses Thu Feb 12 20:49:54 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/dhcp - 1 addresses Thu Feb 12 20:49:54 2015 daemon.info dnsmasq-dhcp[1240]: read /etc/ethers - 0 addresses Thu Feb 12 20:50:33 2015 kern.info kernel: [ 110.140000] rt305x-esw 10110000.esw: link changed 0x00 Thu Feb 12 20:50:36 2015 kern.info kernel: [ 113.690000] rt305x-esw 10110000.esw: link changed 0x01 Thu Feb 12 20:50:45 2015 daemon.notice netifd: radio0 (1776): command failed: Numerical result out of range (-34) Thu Feb 12 20:50:46 2015 kern.info kernel: [ 123.180000] rt305x-esw 10110000.esw: link changed 0x00 Thu Feb 12 20:50:46 2015 kern.info kernel: [ 123.220000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready Thu Feb 12 20:50:46 2015 kern.info kernel: [ 123.240000] device wlan0 entered promiscuous mode Thu Feb 12 20:50:46 2015 kern.info kernel: [ 123.310000] br-lan: port 2(wlan0) entered forwarding state Thu Feb 12 20:50:46 2015 kern.info kernel: [ 123.310000] br-lan: port 2(wlan0) entered forwarding state Thu Feb 12 20:50:46 2015 kern.info kernel: [ 123.320000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Thu Feb 12 20:50:46 2015 daemon.notice netifd: Network device 'wlan0' link is up Thu Feb 12 20:50:47 2015 kern.info kernel: [ 124.780000] rt305x-esw 10110000.esw: link changed 0x01 Thu Feb 12 20:50:48 2015 kern.info kernel: [ 125.310000] br-lan: port 2(wlan0) entered forwarding state Thu Feb 12 20:50:57 2015 kern.info kernel: [ 134.540000] rt305x-esw 10110000.esw: link changed 0x00 Thu Feb 12 20:51:43 2015 daemon.info hostapd: wlan0: STA 74:2f:68:4a:1e:22 IEEE 802.11: authenticated Thu Feb 12 20:51:43 2015 daemon.info hostapd: wlan0: STA 74:2f:68:4a:1e:22 IEEE 802.11: associated (aid 1) Thu Feb 12 20:51:46 2015 daemon.info dnsmasq-dhcp[1240]: DHCPDISCOVER(br-lan) 74:2f:68:4a:1e:22 Thu Feb 12 20:51:46 2015 daemon.info dnsmasq-dhcp[1240]: DHCPOFFER(br-lan) 192.168.1.206 74:2f:68:4a:1e:22 Thu Feb 12 20:51:46 2015 daemon.info dnsmasq-dhcp[1240]: DHCPREQUEST(br-lan) 192.168.1.206 74:2f:68:4a:1e:22 Thu Feb 12 20:51:46 2015 daemon.info dnsmasq-dhcp[1240]: DHCPACK(br-lan) 192.168.1.206 74:2f:68:4a:1e:22 xonom Thu Feb 12 20:51:46 2015 daemon.warn odhcpd[780]: DHCPV6 SOLICIT IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::226/128 Thu Feb 12 20:51:47 2015 daemon.warn odhcpd[780]: DHCPV6 SOLICIT IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::226/128 Thu Feb 12 20:51:49 2015 daemon.warn odhcpd[780]: DHCPV6 SOLICIT IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::226/128 Thu Feb 12 20:51:49 2015 daemon.warn odhcpd[780]: DHCPV6 REQUEST IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::226/128 Thu Feb 12 20:51:49 2015 daemon.info dnsmasq[1240]: read /etc/hosts - 1 addresses Thu Feb 12 20:51:49 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/odhcpd - 2 addresses Thu Feb 12 20:51:49 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/dhcp - 1 addresses Thu Feb 12 20:51:49 2015 daemon.info dnsmasq-dhcp[1240]: read /etc/ethers - 0 addresses Thu Feb 12 21:48:13 2015 daemon.info hostapd: wlan0: STA 74:2f:68:4a:1e:22 IEEE 802.11: authenticated Thu Feb 12 21:48:13 2015 daemon.info hostapd: wlan0: STA 74:2f:68:4a:1e:22 IEEE 802.11: associated (aid 1) Thu Feb 12 21:48:13 2015 daemon.info dnsmasq-dhcp[1240]: DHCPREQUEST(br-lan) 192.168.1.206 74:2f:68:4a:1e:22 Thu Feb 12 21:48:13 2015 daemon.info dnsmasq-dhcp[1240]: DHCPACK(br-lan) 192.168.1.206 74:2f:68:4a:1e:22 xonom Thu Feb 12 21:48:15 2015 daemon.warn odhcpd[780]: DHCPV6 CONFIRM IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: not on-link fd51:c663:6ce5::226/128 Thu Feb 12 21:48:16 2015 daemon.warn odhcpd[780]: DHCPV6 CONFIRM IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: not on-link fd51:c663:6ce5::226/128 Thu Feb 12 21:48:16 2015 daemon.warn odhcpd[780]: DHCPV6 SOLICIT IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::226/128 Thu Feb 12 21:48:16 2015 daemon.info dnsmasq[1240]: read /etc/hosts - 1 addresses Thu Feb 12 21:48:16 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/odhcpd - 1 addresses Thu Feb 12 21:48:16 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/dhcp - 1 addresses Thu Feb 12 21:48:16 2015 daemon.info dnsmasq-dhcp[1240]: read /etc/ethers - 0 addresses Thu Feb 12 21:48:17 2015 daemon.warn odhcpd[780]: DHCPV6 REQUEST IA_NA from 0004e7031e8678f42081d085e44e6fd0daf6 on br-lan: ok fd51:c663:6ce5::226/128 Thu Feb 12 21:48:18 2015 daemon.info dnsmasq[1240]: read /etc/hosts - 1 addresses Thu Feb 12 21:48:18 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/odhcpd - 2 addresses Thu Feb 12 21:48:18 2015 daemon.info dnsmasq[1240]: read /tmp/hosts/dhcp - 1 addresses Thu Feb 12 21:48:18 2015 daemon.info dnsmasq-dhcp[1240]: read /etc/ethers - 0 addresses --- Fin del código --- Hay varias cosas que aún quedán por arreglar, como el tamaño de la flash por ejemplo no está del todo correctamente al igual que algunas de las zonas donde apunta (las ganas por probar a ver que tal iba ^-^), wifi y ethernet son funcionales. Este es el dts que he creado para ello: --- Código: ---/dts-v1/; /include/ "rt3050.dtsi" / { compatible = "ZTE-IX350", "ralink,rt3050-soc"; model = "ZTE IX350"; chosen { bootargs = "console=ttyS0,115200"; }; pinctrl { state_default: pinctrl0 { gpio { ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; ralink,function = "gpio"; }; }; }; cfi@1f000000 { compatible = "cfi-flash"; reg = <0x1f000000 0x800000>; bank-width = <2>; device-width = <2>; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "u-boot"; reg = <0x0 0x40000>; read-only; }; partition@30000 { label = "u-boot-env"; reg = <0x40000 0x20000>; read-only; }; factory: partition@40000 { label = "factory"; reg = <0x60000 0x20000>; read-only; }; partition@50000 { label = "firmware"; reg = <0x80000 0xf80000>; }; }; ethernet@10100000 { mtd-mac-address = <&factory 0x28>; }; esw@10110000 { ralink,portmap = <0x3f>; }; wmac@10180000 { ralink,mtd-eeprom = <&factory 0>; }; otg@101c0000 { status = "okay"; }; i2c-gpio { compatible = "i2c-gpio"; gpios = <&gpio0 1 0 &gpio0 2 0>; i2c-gpio,delay-us = <10>; }; }; --- Fin del código --- No pongo la imagen porque contiene varios fallos, y el dts ahora que lo veo con la cabeza más depejada tiene algunas cosillas que no están bien del todo. Editado por Tki2000: He intentado cuadrar un poquito más el foro... |
jar229:
Felicidades por el trabajo, mekkon >:( >:( Le pongo chicheta y lo añado al recopilatorio [Índice] Hilos relevantes de OpenWrt |
mekkon:
--- Cita de: jar229 en 13-02-2015, 13:05 (Viernes) ---Felicidades por el trabajo, mekkon >:( >:( Le pongo chicheta y lo añado al recopilatorio [Índice] Hilos relevantes de OpenWrt --- Fin de la cita --- Genial, he corregido ya el tamaño de la flash y en el arranque ya no hace correcciones, nuevo dts: --- Código: ---/dts-v1/; /include/ "rt3050.dtsi" / { compatible = "ZTE-IX350", "ralink,rt3050-soc"; model = "ZTE IX350"; chosen { bootargs = "console=ttyS0,115200"; }; pinctrl { state_default: pinctrl0 { gpio { ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; ralink,function = "gpio"; }; }; }; cfi@1f000000 { compatible = "cfi-flash"; reg = <0x1f000000 0x1000000>; bank-width = <2>; device-width = <2>; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "u-boot"; reg = <0x0 0x40000>; read-only; }; partition@40000 { label = "u-boot-env"; reg = <0x40000 0x20000>; read-only; }; factory: partition@60000 { label = "factory"; reg = <0x60000 0x20000>; read-only; }; partition@80000 { label = "firmware"; reg = <0x80000 0xf80000>; }; }; ethernet@10100000 { mtd-mac-address = <&factory 0x28>; }; esw@10110000 { ralink,portmap = <0x3f>; }; wmac@10180000 { ralink,mtd-eeprom = <&factory 0>; }; otg@101c0000 { status = "okay"; }; i2c-gpio { compatible = "i2c-gpio"; gpios = <&gpio0 1 0 &gpio0 2 0>; i2c-gpio,delay-us = <10>; }; }; --- Fin del código --- he modificado también estos ficheros para añadir soporte: openwrt/target/linux/ramips/base-files/etc/uci-defaults/02_network openwrt/target/linux/ramips/base-files/etc/lib/ramips.sh openwrt/target/linux/ramips/base-files/etc/lib/upgrade/platform.sh openwrt/target/linux/ramips/image/Makefile Al intentar actualizar por luci, me dice que la imagen no es válida... si alguien sabe darme alguna idea del porqué, encantado ;) de momento lo hago por uboot y tftp... También hay un detalle interesante, wimax, he visto que hay soporte para "WiMAX devices based on Samsung CMC-730", pero para ¿BECEEM BCSM250-1? |
Navegación |
Índice de Mensajes |
Página Siguiente |