Seguridad Wireless - Wifi
Equipos y materiales => Puntos de acceso, routers, switchs y bridges => Openwrt & LEDE => Mensaje iniciado por: borderline en 02-09-2016, 22:00 (Viernes)
-
Vaya por delante esto
El post no viola nada y no hay problema en poner fotos del router.
Resulta que el vrv9510 es el Livebox Next (http://www.redeszone.net/orange/livebox-next/).
Esto es un bootlog de openwrt corriendo en LIVEVOX NEXT (Astoria Networks vrv9510) la imagen del router que puede verse en este hilo:
https://foro.seguridadwireless.net/openwrt/%28-desarrollo-%29-astoria-networks-vrv9510/
El WIFI no funciona habria que trabajar sobre ello y no he provado el ADSL y me pareceria de milagro que funcionase.
Haber si gente con conocimientos en condiciones se anima porque hasta aqui es hasta donde yo llego porque no se por donde tirar.
ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot
U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx
Board: ZyXEL P-2812HNU-Fx
SoC: Lantiq VRX288 v1.2
CPU: 500 MHz
IO: 250 MHz
BUS: 250 MHz
BOOT: NAND
DRAM: 256 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 2 1 0
NAND read: device 0 offset 0x60000, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-3.18.21
Created: 2015-09-23 21:03:42 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1724467 Bytes = 1.6 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.21 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46993) ) #13 Wed Sep 23 23:01:26 CEST 2015
[ 0.000000] SoC: VR9 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00010082
[ 0.000000] Readback ErrCtl register=00010082
[ 0.000000] Memory: 124388K/131072K available (3794K kernel code, 161K rwdata, 1064K rodata, 208K init, 213K bss, 6684K reserved)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.168000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.172000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.176000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.180000] IO 0x000000001ae00000..0x000000001affffff
[ 0.192000] gpio-stp-xway 1e100bb0.stp: Init done
[ 0.196000] usbcore: registered new interface driver usbfs
[ 0.200000] usbcore: registered new interface driver hub
[ 0.204000] usbcore: registered new device driver usb
[ 0.208000] PCI host bridge to bus 0000:00
[ 0.212000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.216000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.220000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.224000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x18003fff]
[ 0.228000] Switched to clocksource MIPS
[ 0.232000] NET: Registered protocol family 2
[ 0.236000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.244000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.252000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.256000] TCP: reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.264000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.272000] NET: Registered protocol family 1
[ 0.276000] gptu: totally 6 16-bit timers/counters
[ 0.284000] gptu: misc_register on minor 63
[ 0.288000] gptu: succeeded to request irq 126
[ 0.292000] gptu: succeeded to request irq 127
[ 0.296000] gptu: succeeded to request irq 128
[ 0.300000] gptu: succeeded to request irq 129
[ 0.304000] gptu: succeeded to request irq 130
[ 0.308000] gptu: succeeded to request irq 131
[ 0.316000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[ 0.320000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[ 0.328000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7940000
[ 0.336000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7940000
[ 0.440000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.464000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.468000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.480000] msgmni has been set to 242
[ 0.492000] io scheduler noop registered
[ 0.496000] io scheduler deadline registered (default)
[ 0.504000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.512000] console [ttyLTQ0] enabled
[ 0.512000] console [ttyLTQ0] enabled
[ 0.520000] bootconsole [early0] disabled
[ 0.520000] bootconsole [early0] disabled
[ 0.532000] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[ 0.532000] nand: Eon NAND 128MiB 3,3V 8-bit
[ 0.532000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 0.548000] Scanning device for bad blocks
[ 0.584000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[ 0.592000] Creating 4 MTD partitions on "10000000.nand-parts":
[ 0.596000] 0x000000000000-0x000000040000 : "uboot"
[ 0.604000] 0x000000040000-0x000000060000 : "uboot-env"
[ 0.608000] 0x000000060000-0x000000260000 : "kernel"
[ 0.612000] 0x000000260000-0x000008000000 : "ubi"
[ 0.720000] libphy: lantiq,xrx200-mdio: probed
[ 0.736000] net-xrx200: invalid MAC, using random
[ 0.804000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[ 0.872000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[ 0.940000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[ 1.008000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[ 1.016000] net-xrx200: invalid MAC, using random
[ 1.080000] eth1: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[ 1.084000] wdt 1f8803f0.watchdog: Init done
[ 1.092000] TCP: cubic registered
[ 1.092000] NET: Registered protocol family 10
[ 1.104000] NET: Registered protocol family 17
[ 1.108000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.120000] Bridge firewalling registered
[ 1.124000] 8021q: 802.1Q VLAN Support v1.8
[ 1.132000] UBI: auto-attach mtd3
[ 1.132000] UBI: attaching mtd3 to ubi0
[ 1.304000] UBI: scanning is finished
[ 1.316000] UBI: attached mtd3 (name "ubi", size 125 MiB) to ubi0
[ 1.324000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.328000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.336000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.344000] UBI: good PEBs: 1005, bad PEBs: 0, corrupted PEBs: 0
[ 1.348000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.356000] UBI: max/mean erase counter: 4/3, WL threshold: 4096, image sequence number: 665889726
[ 1.364000] UBI: available PEBs: 0, total reserved PEBs: 1005, PEBs reserved for bad PEB handling: 20
[ 1.376000] UBI: background thread "ubi_bgt0d" sta[ 1.400000] UBIFS: background thread "ubifs_bgt0_0" started, PID 252
[ 1.428000] UBIFS: recovery needed
[ 1.524000] UBIFS: recovery completed
[ 1.528000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.532000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.544000] UBIFS: FS size: 125153280 bytes (119 MiB, 970 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
[ 1.552000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.556000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID CAB512C9-0CE2-40C3-B670-4CFDCD95390A, small LPT model
[ 1.568000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.576000] Freeing unused kernel memory: 208K (804ec000 - 80520000)
[ 1.716000] init: Console is alive
[ 1.720000] init: - watchdog -
[ 1.904000] dwc2 1e101000.ifxhcd: requested GPIO 489
[ 2.764000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[ 2.764000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[ 2.772000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[ 2.780000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[ 2.780000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[ 2.792000] hub 1-0:1.0: USB hub found
[ 2.796000] hub 1-0:1.0: 1 port detected
[ 2.872000] eth0: port 1 got link
[ 3.660000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[ 3.660000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[ 3.668000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[ 3.676000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[ 3.676000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[ 3.688000] hub 2-0:1.0: USB hub found
[ 3.692000] hub 2-0:1.0: 1 port detected
[ 3.728000] init: - preinit -
[ 3.884000] random: procd urandom read with 14 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.992000] mount_root: mounting /dev/root
[ 7.008000] procd: - early -
[ 7.012000] procd: - watchdog -
[ 7.584000] procd: - ubus -
[ 8.604000] procd: - init -
Please press Enter to activate this console.
[ 9.312000] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 9.332000] NET: Registered protocol family 8
[ 9.336000] NET: Registered protocol family 20
[ 9.352000] PPP generic driver version 2.4.2
[ 9.368000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.424000] Lantiq (VRX) DSL CPE MEI driver, version 1.4.8.4, (c) 2013 Lantiq Deutschland GmbH
Lantiq CPE API Driver version: DSL CPE API V4.16.2.4
[ 9.476000]
[ 9.476000] Predefined debug level: 3
[ 9.492000] Loading modules backported from Linux version master-2015-07-21-0-g47cd203
[ 9.500000] Backport generated by backports.git backports-20150626-0-gc1a4168
[ 9.512000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.524000] Infineon Technologies DEU driver version 2.0.0
[ 9.532000] IFX DEU DES initialized (multiblock).
[ 9.536000] IFX DEU AES initialized (multiblock).
[ 9.540000] IFX DEU ARC4 initialized (multiblock).
[ 9.544000] IFX DEU SHA1 initialized.
[ 9.548000] IFX DEU MD5 initialized.
[ 9.552000] IFX DEU SHA1_HMAC initialized.
[ 9.556000] IFX DEU MD5_HMAC initialized.
[ 9.584000] nf_conntrack version 0.5.0 (1946 buckets, 7784 max)
[ 9.612000] NET: Registered protocol family 24
[ 9.636000] xt_time: kernel timezone is -0000
[ 9.712000] cfg80211: World regulatory domain updated:
[ 9.716000] cfg80211: DFS Master region: unset
[ 9.720000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.732000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.740000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.748000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.756000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 9.764000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.776000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.784000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.792000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
ioctl ATM_SETESI: No such device
[ 13.680000] PTM 1.0.27 PTM (E1) firmware version 0.30
[ 13.684000] ifxmips_ptm: PTM init succeed
[ 16.212000] device eth0 entered promiscuous mode
[ 16.220000] br-lan: port 1(eth0) entered forwarding state
[ 16.224000] br-lan: port 1(eth0) entered forwarding state
[ 18.228000] br-lan: port 1(eth0) entered forwarding state
BusyBox v1.23.2 (2015-09-19 21:39:07 CEST) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
DESIGNATED DRIVER (Bleeding Edge, r47026)
-----------------------------------------------------
* 2 oz. Orange Juice Combine all juices in a
* 2 oz. Pineapple Juice tall glass filled with
* 2 oz. Grapefruit Juice ice, stir well.
* 2 oz. Cranberry Juice
-----------------------------------------------------
root@OpenWrt:/# lsmod[ 31.524000] random: nonblocking pool is initialized
aead 4368 0
atm 38098 2 pppoatm
br2684 6912 0
cfg80211 227253 2 rt2x00lib
compat 12031 3 rt2800pci
crc_ccitt 1019 2 rt2800lib
crc_itu_t 1019 0
drv_dsl_cpe_api 157864 0
drv_ifxos 14906 2 drv_dsl_cpe_api
drv_mei_cpe 118435 2 ltq_ptm_vr9
dwc2 52103 1 dwc2_platform
dwc2_platform 2608 0
eeprom_93cx6 1807 1 rt2800pci
gpio_button_hotplug 6208 0
ip6_tables 9697 3 ip6table_raw
ip6t_REJECT 1248 2
ip6table_filter 608 1
ip6table_mangle 1168 1
ip6table_raw 576 1
ip_tables 9901 4 iptable_nat
ipt_MASQUERADE 656 1
ipt_REJECT 992 2
iptable_filter 672 1
iptable_mangle 944 1
iptable_nat 768 1
iptable_raw 640 1
ltq_deu_vr9 26528 0
ltq_ptm_vr9 27141 0
mac80211 426813 3 rt2800lib
nf_conntrack 57868 11 nf_nat_ipv4
nf_conntrack_ftp 5520 1 nf_nat_ftp
nf_conntrack_ipv4 5328 8
nf_conntrack_ipv6 6064 3
nf_conntrack_rtcache 2624 0
nf_defrag_ipv4 838 1 nf_conntrack_ipv4
nf_defrag_ipv6 9207 1 nf_conntrack_ipv6
nf_log_common 2543 2 nf_log_ipv4
nf_log_ipv4 3296 0
nf_log_ipv6 3680 0
nf_nat 10876 5 nf_nat_ipv4
nf_nat_ftp 1296 0
nf_nat_ipv4 4369 1 iptable_nat
nf_nat_masquerade_ipv4 1564 1 ipt_MASQUERADE
nf_reject_ipv4 1907 1 ipt_REJECT
nf_reject_ipv6 2295 1 ip6t_REJECT
ppp_async 7568 0
ppp_generic 22274 4 pppoe
pppoatm 3664 0
pppoe 9376 2
pppox 1386 1 pppoe
rt2800lib 94976 2 rt2800pci
rt2800mmio 7234 1 rt2800pci
rt2800pci 4064 0
rt2x00lib 37439 5 rt2800pci
rt2x00mmio 1968 2 rt2800pci
rt2x00pci 1522 1 rt2800pci
slhc 4971 1 ppp_generic
x_tables 11109 26 ipt_REJECT
xt_CT 2800 0
xt_LOG 768 0
xt_REDIRECT 1344 0
xt_TCPMSS 2752 2
xt_comment 480 62
xt_conntrack 2160 10
xt_id 480 0
xt_limit 1344 20
xt_mac 624 0
xt_mark 672 0
xt_multiport 1216 0
xt_nat 1152 0
xt_state 704 0
xt_tcpudp 1728 10
xt_time 1808 0
root@OpenWrt:/#
-
hola a todos,
Tengo el Livebox Next y apliqué la copia de seguridad del Livebox 2.1.
Ahora está reiniciando sin fin.
Como puedo resolvar este problema?
Muchas gracias!
-
¿Has probado a pulsar el botón de reset durante unos segundos?
Es un pequeño orificio que está al lado del conector de alimentación.
Un saludo
-
Muchas gracias,
No, no funciona el reset. He activado el recovery mode solamente no puedo conectar con la dirección ip 192.168.1.1 y no se también el PIN code pero quiero intentar muchas pruebas.
-
Muchas gracias,
No, no funciona el reset. He activado el recovery mode solamente no puedo conectar con la dirección ip 192.168.1.1 y no se también el PIN code pero quiero intentar muchas pruebas.
Sé que voy tarde pero puede que con el modo UART puedas recuperarlo