Equipos y materiales > Openwrt & LEDE
[Desarrollo] OpenWrt en Huawei HG622
<< < (30/32) > >>
pepexx:
Parece ser que tu HG622 tiene una placa distinta y por eso está dando esos problemas. De todas maneras, según el log que pones, parece que la tarjeta wifi es detectada correctamente.

La primera vez que se carga un firmware suele dar el error al cargar la eprom. ¿Te has fijado si sigue saliendo ese error en los siguientes arranques?

También puedes mirar en este hilo a ver si te sirve:

https://foro.seguridadwireless.net/openwrt/antenas-usb-rt3572-y-openwrt/

Saludos.
danitool:
Vale driversat si funciona con el firmware original, la pregunta es: el chip también lo detecta como rt3572 en el firmware original?

Parece raro que tenga ese chip, si es más bien propio de un USB.

Igual el problema es que están corruptos los datos de calibración.
driversat:
firmware original : HG622V100R001C33B021_upgrade_main.bin de Jazztel España (wifi funciona con nombre "SSID" pero no se la clave)
log:

Code Address: 0x80010000, Entry Address: 0x8028a000
Decompression OK!
Entry at 0x8028a000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
155 buffers found.
Closing DMA Channels.
Starting program at 0x8028a000
Linux version 2.6.21.5 (wangzhiquan@build.huawei.com) (gcc version 4.2.3) #96 Tue Sep 27 21:55:37 CST 2011
Pri Table Addr = 0040
ulBootFlag = 0005
Flash 0 at 0xb8000000
  Size : 16 MB
  Regions : 1
    0 : 0x00000000 - 0x00020000 * 128
CPU revision is: 0002a031
Determined physical RAM map:
 memory: 01f00000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 7874
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28596k/31744k available (1935k kernel code, 3148k reserved, 596k data, 100k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
Mount-cache hash table entries: 512
wait instruction: enabled
bhal: bhalInit entry
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 128 (order: -3, 512 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 3 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.

==boot from main kernel==

==pTag->rootfsAddress=0xbfc20100 pTag->kernelAddress=0xc008e100==
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8020100,4644864]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbtest
MoniterInit entry

Led_module_init ok<6>Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Sep 27 2011 11:52:20
GACT probability on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (248 buckets, 1984 max)
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 100k freed
init started: BusyBox vv1.9.1 (2011-09-27 11:55:09 CST)
starting pid 107, tty '': '/etc/init.d/rcS'
RCS DONE
starting pid 109, tty '': '/bin/sh'


BusyBox vv1.9.1 (2011-09-27 11:55:09 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

-/bin/sh: atserver: not found
-/bin/sh: usbdiagd: not found
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache  Char Driver v2.1 Mar 17 2010 13:26:21 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Mar 17 2010 13:26:20
Broadcom Packet CMF (Experimental) Char Driver v0.1 Mar 17 2010 02:52:58 Registered<232>
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Mar 17 2010 02:52:58 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
Broadcom Packet CMF (Experimental) SWC RESET.
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Mar 17 2010 02:52:58 Registered
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Mar 17 2010 02:52:58 Registered
Broadcom Packet CMF (Experimental) ENABLED.

Warning!!! mac addr has not been set, please set it.
eth0.5: MAC Address: 00:10:20:30:40:50
eth0.4: MAC Address: 00:10:20:30:40:50
eth0.3: MAC Address: 00:10:20:30:40:50
eth0.2: MAC Address: 00:10:20:30:40:50
eth0.2 Link UP 100 mbps full duplex
Start mic now ...
Read default configuration file.
load cfm ok.
Cms not started yet.
start log proc...
ifconfig: SIOCSIFNETMASK: Cannot assign requested address

Warning!!! mac addr has not been set, please set it.
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)


=== pAd = c0103000, size = 448160 ===

<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xb1000000, csr_addr=0xb1000000!
port_no -1 not surported, br:br0, port:wl0
device wl0 is not a slave of br0
port_no -1 not surported, br:br0, port:wl0.1
interface wl0.1 does not exist!
port_no -1 not surported, br:br0, port:wl0.2
interface wl0.2 does not exist!
port_no -1 not surported, br:br0, port:wl0.3
interface wl0.3 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device

 begin WlanUpInterfaces...
RX DESC a1a12000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
===Ralink RF DATA check error====
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
RTMPFilterCalibration - can't find a valid value, loopcnt=102 stop calibratingSYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
Main bssid = 00:0c:43:30:62:01
<==== rt28xx_init, Status=0
0x1300 = 00064320
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4

 wlan_mode set come in , argv[2] = bgnmixed
wlancmd txpwr set:95

 begin WlanSetupBridge...
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state

 begin WlanStartServices...
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4
ATP_WLAN_Init SUCCESS!!

Warning!!! mac addr has not been set, please set it.
bcmxtmrt: MAC address: 00 10 20 30 40 51
Use default bin /var/cwmp now ...
BcmAdsl_Initialize=0xC00B88B4, g_pFnNotifyCallback=0xC00EB3F4
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 066, PhaseValue = -050, PhaseCntl = 0x3FBE0000
QPROC is aligned, i = 068, PhaseValue = -050, PhaseCntl = 0x3FBE3FBC
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
pSdramPHY=0xA1FFFFF8, 0x0 0x0
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xBE300 => 0xEBA20 ***
AdslCoreSharedMemInit: shareMemAvailable=83392
AdslCoreHwReset: pLocSbSta=80d38000 bkupThreshold=3072
AdslCoreHwReset:  AdslOemDataAddr = 0xA1FB3C78
atp: cur kernel version:[2.6.21.5]

Warning!!! mac addr has not been set, please set it.
insmod: can't open '/lib/extra/vnet.ko': No such file or directory
device eth0.2 entered promiscuous mode
device eth0.3 entered promiscuous mode
device eth0.4 entered promiscuous mode
device eth0.5 entered promiscuous mode
br0: port 2(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.2) entering forwarding state
device eth0 is not a slave of br0

Warning!!! mac addr has not been set, please set it.
eth0.2 Link DOWN.
br0: port 2(eth0.2) entering disabled state
sh: cannot create /var/at/tdconnstatus: nonexistent directory

Current sntp process is 546!
eth0.2 Link UP 100 mbps full duplex
br0: port 2(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.2) entering forwarding state
killall: ddnsc: no process killed

 xtmcfgdrv: port mirroring config.

 xtmcfgdrv: port mirroring config.
 Stop mirror atm package to eth0.5
br0: port 3(eth0.3) entering disabled state
br0: port 4(eth0.4) entering disabled state
br0: port 5(eth0.5) entering disabled state
Append upnp ssdp listener ok.
Use default bin /var/upnp now ...

Warning!!! mac addr has not been set, please set it.
Enable Got value: 1
NATEnabled Got value: 1


no usb device,can not launch samba server.
driversat:

--- Cita de: danitool en 03-03-2016, 13:22 (Jueves) ---Vale driversat si funciona con el firmware original, la pregunta es: el chip también lo detecta como rt3572 en el firmware original?

Parece raro que tenga ese chip, si es más bien propio de un USB.

Igual el problema es que están corruptos los datos de calibración.

--- Fin de la cita ---

Hola Danitool

supongo que si, los datos de calibracion estan corruptos
como recalibrar si tienes una idea por favor.

Saludos
pepexx:
Buenas tardes,

Por si a alguien le sirve, he compilado un versión actualizada de firmware para el HG622.

LEDE Reboot r1213


SMP, FPU Emulation, LuCi, soporte para discos usb en formato ntfs, vfat y ext2-3-4, cifsmount, transmission, p910nd (servidor de impresion), servidor samba, vsftpd (servidor de ftp), wol, swap-utils, hd-idle, qos, statistics, upnp, ddns, htop

http://ul.to/9dxcekki

Saludos.
Navegación
Índice de Mensajes
Página Siguiente
Página Anterior

Ir a la versión completa