Seguridad Wireless - Wifi
Suite Seguridad Wireless => Live wifislax => Mensaje iniciado por: Alexis-CS en 03-03-2015, 21:59 (Martes)
-
Hola estoy testeando la seguridad de un TV LG... Obviamente todo en la legalidad y sin asaltar a ningún vecino
Hay varias cosas extrañas el pin cambia aleatoriamente cada día y anunque en goyscrip y reaver o inflator el pin wps es detectado y confirmado como bueno nunca me muestra la clave..
No se sí será problema mío aunque haciendo pruebas en routers sí que funciona todo perfectamente mostrando la clave wpa...
alguna posible solución ?
-
porque remarcas que Obviamente todo en la legalidad y sin asaltar a ningún vecino si nadie te dijo nada
para que nadie te lo diga de entrada y pasar como tuyo?
a mi me suena a eso
A mi tambien me suena a eso, y mas en bares y restaurantes que disponen de dichas tv, y claro, un ejemplo, pues mira en el manual que contraseña es, asi que ale
saludos
-
He dicho que obviamente por que sí no fuera de mi propiedad sería delito y como dicen las normas del foro no estaría permitido nisiquiera comentarlo...
Como digo sólo estoy testeando la seguridad del tv y ya lo tengo como reto petsonal...
El código pin obviamente lo conozco ahí no está el problema...aunque como cada vez que enciendo el tv cambia sería difícil que me lo encontraran... Pero yo mismo logré encontrarlo una vez con el goyscrip... ;)
En fin retomando el tema encontre un post en inglés que trataba el tema pero no conseguí la asociación con wps_reg
Este es el tema que encontré
Hopefully this helps out any future wanderers who recover a PIN w/reaver but no PSK, as I have had this happen a few times myself with different testing devices and firmwares.
I am not 100% certain why this occurs, but I have a feeling that there’s more than one reason behind it. Regardless, it's important to know that you CAN authenticate to the AP with just the pin, and in many cases, you will be able to recover that sessions PSK, albeit a manual processes.
I use debian squeeze (6.0), with kernel 3.2.0-0 from backports, along with latest compat-wireless (3.3.1). I have tested this with wpa_supplicant from the repos (v0.6.10), and not from source.
First, set yourself up a very basic wpa_supplicant.conf in /etc/wpa_supplicant.conf: --ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=0 update_config=1 --Second, start wpa_supplicant in daemon mode: wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant.conf –B
Third, run wpa_cli, and verify that it's working by issuing command 'status'. You should see wpa_state=INACTIVE
Fourth, lets add our BSSID and PIN: wps_reg xx:xx:xx:xx:xx:xx 12345678
You should see an "OK". Wait a few more seconds as wpa_supplicant picks up the BSSID and tries to associate and perform key negotiation. What you want to see is "CTRL-EVENT-CONNECTED", which will indicate that the PIN was accepted and that you're now associated.
At this point, if you were to exit wpa_cli, you could run dhclient on wlan0 and would be offered an IP from the AP, assuming DHCPd were enabled.
Go ahead and type the command 'save', which should output another "OK". This will update the wpa_supplicant.conf file, as specified from the command line, with a static configuration for this new network.
Verify by: cat /etc/wpa_supplicant.conf
If all went well, you should have a line under this new network titled 'psk'. Good luck!
-
NInguna ayuda....
No esperaba comentarios en masa... Pero que menos que alguna de las respuestas recibidas no fuera sobre la propiedad del AP y si alguna impresion sobre el tema...
Nada... Dejemos el tema....