Seguridad Wireless - Wifi
Equipos y materiales => Puntos de acceso, routers, switchs y bridges => Openwrt & LEDE => Mensaje iniciado por: poomerang en 10-09-2008, 15:56 (Miércoles)
-
Hola
Bueno pues me han regalado un router wireless de tele2 - telsey 502 - (les mandaron el router y luego no tenían cobertura en la zona :-' :-') y lo primero que he hecho ha sido abrirlo:
- chipset broadcom (4318)
- conector de 4 pines con sus pines ;D
- puerto de 12 pines
Como tenía un cable nokia ttl-rs232 de una fonera pues lo he conectado de varias formas hasta que al final ....
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:03:XX:XX:XX:XX
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................###
### Not default mac address
### 00 03 6f 75 de 58
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Code Address: 0x80010000, Entry Address: 0x801a2018
Decompression OK!
Entry at 0x801a2018
Closing network.
Starting program at 0x801a2018
Linux version 2.6.8.1 (devluc@pisaur.telsey.loc) (gcc version 3.4.2) #1 Mon Oct 9 13:15:54 CEST 2006
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
Total Flash size: 4096K with 71 sectors
CPVA502+ prom init
CPU revision is: 00029107
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 14008k/16000k available (1321k kernel code, 1972k reserved, 282k data, 72k init, 0k highmem)
Calibrating delay loop... 255.59 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 80158e14
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
bcm963xx_mtd: rootfs_addr = 0xBFC10100, kernel_addr = 0xBFEAC100
brcmboard: brcm_board_init entry
GPIO (0x4) LOW -- KIT ON POTS
A confirm button interrupt is not configured on this board
CPU monitor calibration
Calibration loops: 51134656
bcm963xx_serial driver v2.0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2006.10.09-11:20+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2006.10.09-11:20+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348B0 Ethernet Network Device v0.3 Oct 9 2006 13:14:25
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:03:XX:XX:XX:XX
Broadcom BCM6348B0 Ethernet Network Device v0.3 Oct 9 2006 13:14:25
Config External PHY Through MDIO
mii_init: mii hardware reset
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth1: MAC Address: 00:03:XX:XX:XX:XX
Telsey BCM6348B0 USB Network Device v0.4 Oct 9 2006 13:14:29
usb0: MAC Address: 00 03 XX XX XX XX
usb0: Host MAC Address: 00 03 XX XX XX XX
Telsey CPVA502+-W, hwVer = 0xb, USB product ID set to 6310
MAGIC USB configuration
Endpoint: endpoint_init entry
BOS: Enter bosInit
Enter bosAppInit
Exit bosAppInit
BOS: Exit bosInit
Endpoint: endpoint_init COMPLETED
loading Broadcom WIFI module
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board)
wl0 MAC Address: 00:03:XX:XX:XX:XX
wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe2.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
wlctl: wlctl: BcmAdsl_Initialize=0xC005E218, g_pFnNotifyCallback=0xC0078AD4
pSdramPHY=0xA0FFFFF8, 0x7995F 0xDEADBECF
AdslCoreHwReset: AdslOemDataAddr = 0xA0FF68A0
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_conntrack_h323: init
ip_nat_h323: initialize the module!
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_conntrack_ipsec.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_nat_ipsec.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_sip.ko': No such file or directory
==> Bcm963xx Software Version: 3.4.6V-h323.A2pB020a1.d17e <==
device usb0 entered promiscuous mode
bcm63xxenet: Command 35318 not supported.
app: configure ethernet eth0 speed failed.
bcm63xxenet: Command 35317 not supported.
app: configure ethernet eth0 duplex type failed.
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
bcm63xxenet: Command 35318 not supported.
app: configure ethernet eth1 speed failed.
bcm63xxenet: Command 35317 not supported.
app: configure ethernet eth1 duplex type failed.
device eth1 entered promiscuous mode
br0: port 3(eth1) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1) entering forwarding state
Setting SSID "Telsey502plus"
Setting SSID "Guest"
pvc2684d: Interface "nas_0_44" created sucessfully
pvc2684d: Communicating over ATM 0.0.44, encapsulation: LLC
Starting the H323 application with the following parameters:H323 Gatekeeper address: 0.0.0.0H323 Gatekeeper ID: H323 Secondary Gatekeeper address: 0.0.0.0H323 Secondary Gatekeeper ID: H323 Gatekeeper port: 1719H323 Time to Live: 3600H323 Keep Alive Interval: 75 % of Time to LiveH323 Terminal Type: terminalH323 FastStart: Off (connect)H323 Alias: TelseyPhone Line1: Phone Line2: Dialplan Line1: .t4-Dialplan Line2: .t4-Supp. Services enable mask: 0x0:0x0User defined Supp. Services codes: Call Waiting Timeout (in seconds): 15Override Category: OffQ931 T301 Timer (in seconds): 180Q931 T303 Timer (in seconds): 4Q931 T310 Timer (in seconds): 120Starting restorebtnd...
No-answer timeout (in seconds): 120Offhook timeout (in seconds): 100H245 Tunneling: OffH245 Channel After Fast Start: OffEarly H245: OffOOB DTMF: OffAlerting PI: 8Progress PI: 8Bearer Capability: SpeechPlug change timeout (in seconds): OffH323 TOS: OffH323 Debugger: mode = Off --- level = ERRORCurrent global voice parameters:Codec G711U: Packet=20(ms) ec=On ss=Off Codec G711A: Packet=20(ms) ec=On ss=Off Codec G729: Packet=20(ms) ec=On ss=Off Codec priority order: G711U,G711A,G729 Country: ITALYCLID signal type: FSKHookFlash interval: 50-200 (ms)On-Hook detection timeout: 600 (ms)Squelch inband DTMF: OffFax feature: OnModem feature: OnPass through codec: OffNLP on Modem detection: OffNLP on Fax detection: OnRTP TOS: A0VodslSettings::getStrParam: Set default G729 configuration parameters (ec and ss)VodslSettings::setVar varName = codec_G729_ec, varValue = On
VodslSettings::setVar varName = codec_G729_ss, varValue = Off
Starting cpumond...
BcmWan_startInterface: vpi = 0, vci = 33, conId = 1
pWanId status = 0
BUFFER=vodsl h323start -p 0.0.0.0:1719-3600-75-terminal-Off-'' -i br0 -g 0.0.0.0-'' -G connect -c ITALY -s FSK -I 'Telsey' -n num:: -d ".t4-:.t4-" -m G711U,G711A,G729,:20-On-Off:20-On-Off:20-On-Off -t 50 -T 200 -H 600 -X 'Off' -Y 'Off' -S 'Off-A0' -e 'Off-On' -f 'On-On' -u none=0:0=0:0 -W 15 -O Off -L Off -N Off -E Off -B Speech -C Off -U 180 -V 4 -Z 120 -A 120 -F 100 -P 8:8 -o Off -D Off:ERROR &
BcmWan_startInterface: vpi = 0, vci = 44, conId = 1
pWanId status = 0
process `snmp' is using obsolete setsockopt SO_BSDCOMPAT
br0: port 2(eth0) entering disabled state
main(404): pppd 2.4.1 started by admin, uid 0
br0: port 3(eth1) entering disabled state
br0: port 1(usb0) entering disabled state
BOS: Enter bosInit
Enter bosAppInit
Exit bosAppInit
BOS: Exit bosInit
00:00:28 Address for host 0.0.0.0 resolved to 0.0.0.0
00:00:28 Address for host 0.0.0.0 resolved to 0.0.0.0
kernel::endpoint_open
kernel::endpoint_open COMPLETED
00:00:28 EndpointProvis entering: provisioning item 54
00:00:28 EndpointProvis item=54 value=1
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 34
00:00:28 EndpointProvis item=34 value=50
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 35
00:00:28 EndpointProvis item=35 value=200
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 36
00:00:28 EndpointProvis item=36 value=600
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 37
00:00:28 EndpointProvis item=37 value=0
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 38
00:00:28 EndpointProvis item=38 value=0
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 39
00:00:28 EndpointProvis item=39 value=0
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 40
00:00:28 EndpointProvis item=40 value=1
kernel:: endpoint provisioning
00:00:28 EndpointProvis entering: provisioning item 41
00:00:28 EndpointProvis item=41 value=0
kernel:: endpoint provisioning
00:00:28 Endpoint Event task started with pid 389...
00:00:28 Endpoint Packet task started with pid 390 ...
Enter bosStartApp
bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
Enter TaskCreate aoAP
TaskCreate - spawn new task aoAP
Exit TaskCreate
AppResetDetectionEnable() - Enabled reset detection.
Exit bosStartApp
Enter TaskCreate HRTBEAT
TaskCreate - spawn new task HRTBEAT
Exit TaskCreate
HEARTBEAT: Initialized!
slacLe9581Init: Init SLAC for country 10
slac6348Le9581.c: OpenSlac, boardId = 16777219
slac6348Le9581.c: OpenSlac, ABAT disabled
HEARTBEAT: Patient (AC power) pid=0 registered (1 of 16 max registered)
bosMsgQCreate: Created message queue VRGEVQ at address 0x0
Enter TaskCreate VRGEVPR
TaskCreate - spawn new task VRGEVPR
Exit TaskCreate
Enter TaskCreate HCAS
TaskCreate - spawn new task HCAS
Exit TaskCreate
ENDPT: hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x50) of type: 0x3
HEARTBEAT: Patient (Cnx state) pid=1 registered (2 of 16 max registered)
HEARTBEAT: Patient (Endpt hookstate) pid=2 registered (3 of 16 max registered)
HEARTBEAT: Patient (Endpt On/Off signal) pid=3 registered (4 of 16 max registered)
HEARTBEAT: Patient (Endpt Caller ID signal) pid=4 registered (5 of 16 max registered)
HEARTBEAT: Patient (Endpt signal) pid=5 registered (6 of 16 max registered)
HEARTBEAT: Patient (Cnx signal) pid=6 registered (7 of 16 max registered)
ENDPT: hdspVhdOpen Primary Connection VHD success. DSP 0, VHD (0x51) of type: 0x0
HEARTBEAT: Patient (Cnx state) pid=7 registered (8 of 16 max registered)
ENDPT: hdspVhdOpen Line VHD success. DSP 0, VHD (0x52) of type: 0x7
ENDPT 0: Fax Custom Options set to 0x0
Default value for provItemId '47' did not exist
Default value for provItemId '210' did not exist
Default value for provItemId '63' did not exist
ENDPT: Initialization completed successfully for endpt 0
00:00:29 cmCallConfig: entering...
WO........0=*43#
WF........1=#43#
WQ........2=*#43#
RT........12=*31#
RO........13=*32#
RF........17=*33#
RESTORE DEFAULT........11=###*1973*5*2846*147896325*###
ENDPOINT 0:
00:00:29 rtpInit: RTCP task created, taskId = 5126
udpRawOpen: copying socketHandle b
00:00:29 RTP read thread started with pid 398
udpRawSetSendHandle: copying rawHdl 0 senddesc b
udpRawOpen: copying socketHandle e
00:00:29 RTP read thread started with pid 399
udpRawSetSendHandle: copying rawHdl 1 senddesc e
00:00:29 RTCP thread started with pid 397
Resumiendo :
4MB flash
16MB RAM
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Además consigo entrar a un prompt CFE. En el que tengo las siguientes opciones:
*** command status = -1
CFE> help
Available commands:
w Write the whole image start from beginning of the flash
e Erase [n]vram or [a]ll flash except bootrom
r Run program from flash image or from host depend on [f/h] flag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
m test mac client
i Erase persistent storage data
b Change board parameters
d Set default mac address
reset Reset the board
flashimage Flashes a compressed image after the bootloader.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE>
Supongo que con esto se le podra cambiar el firm desde un TFTP (tipo fonera). ¿?
He visto en la pagina de openwrt en devices compatibles algunos equipos con similares características, ... como lo veis ¿?
Alguna idea o sugerencia ...
El router ahora mismo esta capado y no se puede acceder a él via web ni por telnet (o al menos no he sido capaz), así que para lo que sirve no hay miedo de freirlo. Bueno luego estaría el tema jtag, que supongo que será las conexion esa de 12 pines ...
Bueno lo siento por el ladrillo ...
Saludos y suerte.
-
Ostia !! siento el descuadre pero no puedo editarlo (no veo el boton)
Lo siento. :'(
Saludos y suerte
-
Ya no descuadra ;) ;)
PD.Asi esta mejor editado. como estaba antes.
-
Gracias Hombre.
Saludos y suerte.
-
Soportado oficialmente en OpenWrt para los que querais juguetear con él.
-
hola buenas tardes necesito un poco de ayuda ya que quise instalar el openwrt en el telsey y se ha vuelto loco se enciende el led de rojo que es el de que le llega corriente y el led de link, quiero resucitar el router y instalar bien el openwrt. gracias
-
Buenas, creo que en este router concreto existe un pequeño gran problema.
En su día estuve en contacto con alguien con este router para añadir soporte, el cual se consiguió pero no se hicieron suficientes tests.
El problema es el siguiente, resulta que el router tiene dos interfaces de red eth0 y eth1, eth0 es la interna del propio SoC pero por defecto Openwrt asigna a esta interfaz la ip mediante dhcp, para funcionar como puerto WAN con lo cual no podemos conectarnos a ella. Por defecto el wifi también está desactivado, por lo que tampoco podemos conectarnos por ahí. Solo nos queda eth1 el cual va conectado a un phy externo, este phy externo tiene la particularidad de que se activa con un gpio, el gpio4.
Desafortunadamente solo existía una posibilidad para que este gpio se activase al arrancar OpenWrt y por lo tanto poder usar la única interfaz a la que podríamos conectarnos. Lo que hice fue definirlo como un led más, pero puede que no funcione de forma correcta..
{
.name = "eth1-nrst", /* FIXME: gpio4 enables eth1 phy */
.gpio = 4,
.active_low = 0,
.default_trigger = "default-on",
},y puede que no podamos conectarnos de otra forma que no sea puerto serie..
El problema realmente es del bootloader que debería el mismo activar el gpio. Tampoco creo que hay forma de entrar en la interfaz web CFE del router usando el botón de reset. Solo mediante cable serie. Todo esto falta por confirmar.
Para afinar la configuración en el kernel entonces quedaría primero activar el gpio 4 para que funcione el ethernet, y también en lugar de definir
.enet1 = {
.force_speed_100 = 1,
.force_duplex_full = 1,
}, Sería más correcto definir esto:
.enet1 = {
.has_phy = 1,
.phy_id = 0,
},
-
Buenas,
tengo el modelo que comentáis.
DaniTool te interesa continuar en el desarrollo para dejar el soporte ok ?
Hay dos opciones:
1.- si estas dispuesto si quieres te envío el mío y continuas con el desarrollo
2.- si el proceso de modificación no es muy complicado puedo intentar realizarlo yo mismo... quizas tenga conocimientos informáticos suficientes para poder realizar el asunto, pero necesitaria algunas indicaciones.
Saludos.
-
Pues he aquí el firmware con el par de correcciones que indiqué previamene. AA con las opciones por defecto.
https://files.myopera.com/danitool/xx/telsey_CPVA502plus.zip
Si tienes consola por cable serie, sería útil ver el bootlog.
¿se sabe si el botón reset funciona en este router?
-
Hola a todos,
Yo también tengo un cpva502 de cuando tenia Tele2 y he estado "jugando" con él hasta que lo he dejado "frito", no saca ningún caracter por el puerto serie.
¿Es posible recuperarlo? ¿Con un jtag?
¿O directamente lo uso como pisapapeles?
Me gustaria recuperarlo para aprender y volver a probar con el firmware openwrt.
Gracias por adelantado
Saludos
-
Si no te cargaste nada del hardware físicamente por jugar (no especificas que juegos hacías con él, si jugabas al fútbol con el la cosa pintaría mal), entonces sí podrías recuperarlo perfectamente.
Solo has de flashear el bootloader. Eso sí, ni idea cuales son los pines del JTAG. Del bootloader hay backup:
http://files.myopera.com/danitool/linux/bootloaders/telsey_CPVA502+_MX29LV320CT_CFE.zip
Sobre como flashear el bootloader una vez que tengas el cable JTAG con los pines conectados hay tantas variantes que no sé cual aconsejarte :P. Un ejemplo sería perfectamente el Livebox 1 usando el mismo método de flasheo, pero evidentemente con el bootloader que anteriormente indiqué.
-
Gracias por el bootloader.
Fisicamente está bien, solo lo tengo abierto para acceder a los puertos serie y jtag.
Aun no tengo el jtag y no sé que conexionado poner, así que me tocara investigar.
Los "juegos" solo han sido poner firmware openwrt y animarme a generar uno propio usando el ImageBuilder con el resultado desastroso que ya expliqué. :-[
Ya explicaré si lo consigo y cómo.
Y si no, ya haré un pisapapeles con él. ;D
-
hola buenas tengo todo intalado y configurado del openwrt solo que cuando accedo a la web luci se bloquea. y ya no me deja hacer nada y tengo que hacer todo el proceso tengo un cable seria para hacer todo esto y utilizo el winscp para poner los archivo de package lo otro lo subo por web.gracias
-
hola buenas tengo todo intalado y configurado del openwrt solo que cuando accedo a la web luci se bloquea. y ya no me deja hacer nada y tengo que hacer todo el proceso tengo un cable seria para hacer todo esto y utilizo el winscp para poner los archivo de package lo otro lo subo por web.gracias
Si estás usando la versión 12.09 Attitude Adjustment, es normal que no pueda con luci, con 16 megas el router va al límite.
Las soluciones son hacer un backport a 10.03 (Backfire), o bien ampliar la memoria RAM, o usar AA pero sin interfaz web y siempre con lo mínimo, única y exclusivamente lo que necesitemos.
¿Que hay del firmware que compilé?
https://files.myopera.com/danitool/xx/telsey_CPVA502plus.zip
¿Alguien lo probó? ¿funciona el eth1? ¿funciona el botón de reset?... ¿estamos solos en el universo...?
-
no lo he probado ahora te digo algo
-
te comento lo he instalado y nada el eth1 no va y el reset tampoco con el otro que tenia yo instalado si que va el eth1 pero no el reset.
-
Vale, el botón de reset es normal, parece ser que está de adorno simplemente.
El eth1 en el firmware oficial funciona por defecto sin tener que configurar el puerto?
-
te comento a mi me falla el eth1 aveces funciona y a veces no. te queria preguntar estoy instalando el web luci essentials que es lo basico y se bloquea, me has dicho que instale el backfire ese no me funcion panic syntick o algo asi.
-
te comento a mi me falla el eth1 aveces funciona y a veces no. te queria preguntar estoy instalando el web luci essentials que es lo basico y se bloquea, me has dicho que instale el backfire ese no me funcion panic syntick o algo asi.
¿Podrías poner el log de arranque con mi firmware para ver si el eth1 está ahí o no?
Sobre Backfire es necesario hacer ciertas modificaciones en el código fuente y luego compilarlo, el firm oficial no dispone de soporte para esta placa.
-
bueno hay va http://img138.imageshack.us/img138/5561/54890006.jpg este es tu firmware y este es el de la pagina http://img69.imageshack.us/img69/7465/dibujotpp.jpg
-
He compilado Backfire con soporte para esta placa
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire.zip
La única pega es que este router necesita un arreglo después del primer inicio haciendo el comando:
mtd fixtrx linuxy ni idea si funcionará.
También traté de nuevo corregir el eth1. Por favor pon un log de arranque completo. pero en modo texto, en tus capturas de pantalla no se ve nada....no hagas capturas, solo copia y pégame el texto.
Si quieres pegalo aquí, o en pastebin. Sino será imposible intentar corregir ningún fallo.
-
salvador prueba con estos pin del jtag parecen que son los mismo que el comtred perdonad por el copy y paste http://img502.imageshack.us/img502/9981/20120204173016.jpg
-
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 9
web info: Waiting for connection on socket 0.
CFE>
web info: Waiting for connection on socket 1.
web info: Waiting for connection on socket 0.
web info: Upload 3014660 bytes, Telsey image format.
CFE>
Flashing root file system and kernel at 0xbfc10000: ............................ ...................
.
*** Image flash done *** !
Resetting board...ÿ
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x8042080 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #7 Fri Jan 25 17: 02:12 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd cons ole=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1986k kernel code, 2820k reserved, 362k data, 1 36k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx_flash: Failed to probe using CFI/JEDEC
bcm963xx-flash: probe of bcm963xx-flash.0 failed with error -5
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Cannot open root device "mtdblock2" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
-
es lo mismo que pone con el backfire de la pagina
-
Prueba de nuevo con este
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire2.zip
Y pon de nuevo el log de arranque
-
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #8 Fri Jan 25 18:59:18 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1988k kernel code, 2820k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 30000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length cff00
bcm963xx_flash: Partition 2 is rootfs offset e0000 and length 310000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 30000 and length 3c0000
bcm963xx_flash: Spare partition is 2f0000 offset and length 100000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000030000 : "CFE"
0x000000010100-0x0000000e0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000e0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000
0x0000002f0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000030000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -
Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
device eth0 entered promiscuous mode
PHY 1:1f not found
bcm63xx_enet bcm63xx_enet.1: could not attach to PHY
PHY 1:1f not found
bcm63xx_enet bcm63xx_enet.1: could not attach to PHY
device eth1 entered promiscuous mode
PHY 1:1f not found
bcm63xx_enet bcm63xx_enet.1: could not attach to PHY
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
eth0: link UP - 100/full - flow control off
br-lan: port 1(eth0) entering forwarding state
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (214 buckets, 856 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
-
ya funcion parece que package tengo quer instalar los de backfire
-
Que es lo que funciona, el eth1 no parece que funcione o al menos marca eso el log.
Prueba de nuevo este firmware
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire3.zip
y pega de nuevo el log de arranque
-
el frimware no se que da instalado verda danitool cada vez que lo desconecto de la luz se va todo lo que echo. mañana te subo el log
-
el frimware no se que da instalado verda danitool cada vez que lo desconecto de la luz se va todo lo que echo. mañana te subo el log
Ya dije que después del primer inicio hay que hacer el comando
mtd fixtrx linuxel cual no sé si funcionará, ya que no estaba disponible en Backfire pero traté de hacer un backport, así que después de iniciarlo por primera vez prueba el comando. Sino funciona la cosa se complicaría para hacer funcionar el router en Backfire.
-
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #9 Fri Jan 25 21:10:38 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1988k kernel code, 2820k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 30000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length cff00
bcm963xx_flash: Partition 2 is rootfs offset e0000 and length 310000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 30000 and length 3c0000
bcm963xx_flash: Spare partition is 2f0000 offset and length 100000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000030000 : "CFE"
0x000000010100-0x0000000e0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000e0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000
0x0000002f0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000030000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -
Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
device eth0 entered promiscuous mode
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 2(eth1) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
eth0: link UP - 100/full - flow control off
br-lan: port 1(eth0) entering forwarding state
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (214 buckets, 856 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
BusyBox v1.15.3 (2013-01-09 20:58:29 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/#
-
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/# passwd
Changing password for root
New password:
Bad password: too short
Retype password:
Password for root changed by root
root@OpenWrt:/# mtd fixtrx linux
Trying to fix trx header in linux at 0x0...
Verifying we actually have an imagetag.
Tag verify failed. This may not be a valid image.
root@OpenWrt:/#
-
Otra imagen para probar
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire4.zip
A ver si en esta te funciona
mtd fixtrx linuxPon de nuevo el log de arranque, de paso estoy intentando saber cual es la phy_id del eth1 (hay 31 posibles).
-
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #11 Sat Jan 26 17:50:58 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13564k/16384k available (1988k kernel code, 2820k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length cff00
bcm963xx_flash: Partition 2 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 3 is linux offset 10000 and length 3f0000
bcm963xx_flash: Spare partition is e0000 offset and length 310000
Creating 4 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000e0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x000000400000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008000: 0x674f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008004: 0x4272 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008020: 0x7365 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008024: 0x696f instead
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 7, bad_blocks 0, c->nr_blocks 8
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00 64 mtdblock0 (driver?)
1f01 831 mtdblock1 (driver?)
1f02 64 mtdblock2 (driver?)
1f03 4032 mtdblock3 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
-
Eso fue después de hacer?
mtd fixtrx linux
porque sino fue así no tiene mucho sentido que la anterior imagen funcionase y esta no
-
Otra compilación para probar
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire5.zip
-
te comento danitool despues de instalar la imagen cuando llega a root@ yo le pongo este comando y lo reconoce pero cuando vuelvo a iniciar en serial me salta esto
CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #1 Sun Jan 27 15:10:26 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13472k/16384k available (2053k kernel code, 2912k reserved, 361k data, 132k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.312:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 3 is linux offset 10000 and length 3f0000
bcm963xx_flash: Spare partition is f0000 offset and length 300000
Creating 4 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x000000400000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008000: 0x674f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008004: 0x4272 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008020: 0x7365 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00008024: 0x696f instead
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 7, bad_blocks 0, c->nr_blocks 8
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00 64 mtdblock0 (driver?)
1f01 895 mtdblock1 (driver?)
1f02 64 mtdblock2 (driver?)
1f03 4032 mtdblock3 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
-
¿y que hay del eth1 en este último firmware cuando lo inicias por primera vez?
-
Otro firmware Backfire más para probar
https://files.myopera.com/danitool/xx/telsey_CPVA502plus_backfire6.zip
Esta vez después de hacer mtd fixtrx linux debiera funcionar el siguiente reinicio, y todos los posteriores.
Todavía no sé nada acerca del eth1. Desgraciadamente con un feedback tan pésimo, poco se puede hacer.
De todas formas pon el bootlog de nuevo sino es mucha molestia.
-
Copyright (C) 2003,2004,2005 Telsey Telecommunications.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
100 MB Full-Duplex (auto-neg)
Check consistency for image tag [1]: Found good image at partition [1]
Check consistency for image tag [2]: No image found at partition [2]
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
Initialized Data: 0x8041E610 - 0x80420480 (7792)
BSS Area: 0x80420480 - 0x80424FA0 (19232)
Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
Text (code) segment: 0x80401000 - 0x8041E60C (120332)
Boot area (physical): 0x00527000 - 0x00567000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1
Host IP address : 192.168.1.100
Gateway IP address : 192.168.1.1
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 9
Board Id Name : CPVA502+
Psi size in KB : 24
Number of MAC Addresses (1-32) : 8
Base MAC Address : 00:30:ab:00:00:01
Ethernet PHY Type : Internal
Memory size in MB : 16
mac server test........................
###
### Find default mac address ,try to connect to mac server to replace it
assign_MAC_addr cmd id 1 send packet retries #1 send
assign_MAC_addr cmd id 1 send packet retries #2 send
assign_MAC_addr cmd id 1 send packet retries #3 send
assign_MAC_addr cmd id 1 send packet retries #4 send
assign_MAC_addr cmd id 1 send packet retries #5 send
assign_MAC_addr cmd id 1 send packet retries #6 send
assign_MAC_addr cmd id 1 send packet retries #7 send
assign_MAC_addr cmd id 1 send packet retries #8 send
assign_MAC_addr cmd id 1 send packet retries #9 send
assign_MAC_addr cmd id 1 send packet retries #10 send
### 00 30 ab 00 00 01
*** Press any key to stop auto run (9 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #2 Sun Jan 27 20:42:36 CET 2013
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-3.6
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: CPVA502+
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13472k/16384k available (2053k kernel code, 2912k reserved, 360k data, 132k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.312:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000c2
CFI id 0x000022a7
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
bcm963xx_flash: Spare partition is 280000 offset and length 170000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=280000, len=170000
0x000000280000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: phone
Registered led device: link
Registered led device: eth1-nrst
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 132k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -
Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Generic PHY]
device eth1 entered promiscuous mode
eth0: link UP - 100/full - flow control off
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (212 buckets, 848 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
BusyBox v1.15.3 (2013-01-27 14:49:55 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/# passwd
Changing password for root
New password:
Bad password: too short
Retype password:
Password for root changed by root
root@OpenWrt:/#
-
te quiero hacer un pregunta danitool para instalar los package de web luci como puedo instalarlo por internet .gracias
-
te quiero hacer un pregunta danitool para instalar los package de web luci como puedo instalarlo por internet .gracias
Supongo que el eth1 funciona bien no?, cuando enchufas desenchufas el cable en ese puerto debiera detectar el link, y funcionar correctamente. Debieran salir mensajes en la consola por puerto serie, cuando desenchufas o enchufas.
En ese caso simplemente enchufa el eth0 al puerto de tu router principal que provee internet para que coja la ip para acceder a internet. Una vez que el router tenga acceso a internet:
opkg update
opkg install luci
de todas formas, compilaré un firmware con luci, para ponerlo junto con este en la wiki
-
si funciona lo detecta lo de opkg update me pone bab adress
-
vale danitool cuando lo tenga lo subes.gracias por el trabajo que estas haciendo
-
Firmwares versión Backfire para Telsey CPVA502+W (con y sin luci). Incluye parche para quien quiera hacer su propia compilación en este backport del router a Backfire.
https://files.myopera.com/danitool/linux/Telsey_CPVA502_Backfire_10.03.2.zip
Imprescindible ejecutar
mtd fixtrx linuxdespués del primer inicio
-
a que te refieres con luci i sin luci
-
hola danitool no puedo descargar los package por internet no se i es el routeer este que bloquea la conexion o no se.gracias
-
login as: root
root@192.168.1.1's password:
BusyBox v1.15.3 (2013-01-27 14:49:55 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
---------------------------------------------------
Backfire (10.03.x Snapshot, r33081)
---------------------------------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:~# opkg update
Downloading http://downloads.openwrt.org/backfire/10.03.1/brcm63xx/packages/Packages.gz.
wget: bad address 'downloads.openwrt.org'
Collected errors:
* opkg_download: Failed to download http://downloads.openwrt.org/backfire/10.03.1/brcm63xx/packages/Packages.gz, wget returned 1.
root@OpenWrt:~#
-
root@OpenWrt:~# opkg update
Downloading http://downloads.openwrt.org/backfire/10.03.1/brcm63xx/packages/Packages.gz.
wget: bad address 'downloads.openwrt.org'
Collected errors:
* opkg_download: Failed to download http://downloads.openwrt.org/backfire/10.03.1/brcm63xx/packages/Packages.gz, wget returned 1.
root@OpenWrt:~#
Esto es problema de configuración y no del firmware.
O bien el router no tiene internet (lo tienes conectado por cable ?), o no lo has configurado debidamente ... >:D
-
como lo configuro lo del firmware es el que a copilado danitool y despues me dijo que pusiese esto mtd fix linux algo asi lo estoy conectando a un router livebox al puerto eth0 y el eth1 a el pc. gracias por contestar
-
Si no sabes configurar algo tan sencillo ... te toca leer un poco ;D
Enviado desde mi Infected V4.0 usando Tapatalk 2
-
ok gracias
-
pregunto hay al manual para esto o en algun sitio del foro ya que no consigo nada he mirado lo de config interface y me reconoce el eth0 como wan y el eth1 como lan pero sigo sin conseguir que se conecte a internet y descargar los package.
-
Solo se me ocurre que (dada la escasa información que das, 0 patatero), que 192.168.1.1 es la ip por defecto del telsey, y puede que coincida con la de tu router que provee internet, causando un conflicto.
Puedes probar a cambiar (de forma temporal) la ip LAN del telsey
ifconfig eth1 192.168.3.1por supuesto sobra decir que has de acceder de nuevo haciendo telnet (ó ssh, ó http) a esta nueva ip.
-
gracias por contestar danitool vamos haber si consigo algo calro
-
danitool eso que has puesto de readme para que es el comando he istalado el que tiene luci
-
hola porque cuando le cambias la ip para conecta en modo cliente en openwrt y lo desenchufas de la luz ya no funciona no me deja entrar ni mediante web ni ssh.
-
salvador prueba con estos pin del jtag parecen que son los mismo que el comtred perdonad por el copy y paste http://img502.imageshack.us/img502/9981/20120204173016.jpg
Gracias danitool por la ayuda.
He conseguido ponerle la versión 6 que has publicado.
Después del mtd fixtrx linux, lo he reiniciado, configurado, actualizado,.. sin problemas.
-
Perdón porla omisión javier1990.
Gracias a los dos.
-
Muchas gracias por la currada.
Acabo de meterle a mi viejo telsey de tele2 tu firm y ya va como la seda.
Le he metido primero sin luci y después con ella, sin problema en ambos casos, LAN y WLAN funcionando.
Voy a probar a meterle el chilli a ver si consigo hacerlo servir para controlar por RADIUS una pequeña red con hotspot y AAA, aunque tengo mis dudas dada la capacidad del router. Si lo consigo ya os lo haré saber.
De nuevo gracias.
-
yo también me eh apuntado al tema y lo brickee rapidisimo con un xtractor pude conectar la consola y recuperarlo pero la verdad no se. si se puede usar la voz ip del router con openwrt o activar la adsl2 del bmc
si podeis poner el firm original lo agradeceria
-
Para los que echabais de menos tener el firmware original, gracias a TheMrRafus que generosamente se prestó a hacer un backup, aquí teneis el link de descarga:
https://drive.google.com/uc?export=download&id=0B-EMoBe-_OdBNkNmbUhTZUh5NEU
Ahora ya se puede probar Openwrt pudiendo volver al firm original sin ningún problema.
Saludos.
-
Firmwares versión Backfire para Telsey CPVA502+W (con y sin luci). Incluye parche para quien quiera hacer su propia compilación en este backport del router a Backfire.
https://files.myopera.com/danitool/linux/Telsey_CPVA502_Backfire_10.03.2.zip
Imprescindible ejecutar
mtd fixtrx linuxdespués del primer inicio
Hola, ¿se puede subir el firmware a otro sitio? Es que no me lo puedo bajar. Gracias
-
Firmwares versión Backfire para Telsey CPVA502+W (con y sin luci). Incluye parche para quien quiera hacer su propia compilación en este backport del router a Backfire.
https://files.myopera.com/danitool/linux/Telsey_CPVA502_Backfire_10.03.2.zip
Imprescindible ejecutar
mtd fixtrx linuxdespués del primer inicio
Hola, ¿se puede subir el firmware a otro sitio? Es que no me lo puedo bajar. Gracias
Si no me equivoco, te lo puedes bajar de la wiki oficial de openwrt: http://wiki.openwrt.org/toh/telsey/cpva502.w (http://wiki.openwrt.org/toh/telsey/cpva502.w)
-
Gracias, en la wiki pone 10.03.1 y aquí era el 10.03.2, no se si será el mismo o si hay algun cambio importante hecho al que había aquí.