[Desarrollo] OpenWRT para routers Astoria de ya.com (ARV4518/ARV7518)
<< < (65/207) > >>
g2rp:
Buenas, estoy probando la beta 2 en un arv7518 y me pasa como a brunorro, no me deja subir el txpower de 3dbm, ni con iwconfig ni nada, por lo que el rango es bastante limitado.

He probado compilando con la opción del kernel, Kernel Modules → Wireless Drivers → kmod-ath → Configuration → Force Atheros drivers to respect the user's regdomain settings = YES, y deja cambiar de regdomain sin problemas (activa el canal 14 por ejemplo si lo pones en Japon) pero el txpower nada.

Haciendo iw list: Citar

iw list
Wiphy phy0
   Band 1:
      Capabilities: 0x11ce
         HT20/HT40
         SM Power Save disabled
         RX HT40 SGI
         TX STBC
         RX STBC 1-stream
         Max AMSDU length: 3839 bytes
         DSSS/CCK HT40
      Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
      Minimum RX AMPDU time spacing: 8 usec (0x06)
      HT TX/RX MCS rate indexes supported: 0-15
      Frequencies:
         * 2412 MHz [1] (3.0 dBm)
         * 2417 MHz [2] (3.0 dBm)
         * 2422 MHz [3] (3.0 dBm)
         * 2427 MHz [4] (3.0 dBm)
         * 2432 MHz [5] (3.0 dBm)
         * 2437 MHz [6] (3.0 dBm)
         * 2442 MHz [7] (3.0 dBm)
         * 2447 MHz [8] (3.0 dBm)
         * 2452 MHz [9] (3.0 dBm)
         * 2457 MHz [10] (3.0 dBm)
         * 2462 MHz [11] (3.0 dBm)
         * 2467 MHz [12] (3.0 dBm)
         * 2472 MHz [13] (3.0 dBm)
         * 2484 MHz [14] (disabled)
      Bitrates (non-HT):
         * 1.0 Mbps
         * 2.0 Mbps (short preamble supported)
         * 5.5 Mbps (short preamble supported)
         * 11.0 Mbps (short preamble supported)
         * 6.0 Mbps
         * 9.0 Mbps
         * 12.0 Mbps
         * 18.0 Mbps
         * 24.0 Mbps
         * 36.0 Mbps
         * 48.0 Mbps
         * 54.0 Mbps
   max # scan SSIDs: 4
   max scan IEs length: 2257 bytes
   Coverage class: 1 (up to 450m)
   Supported Ciphers:
      * WEP40 (00-0f-ac:1)
      * WEP104 (00-0f-ac:5)
      * TKIP (00-0f-ac:2)
      * CCMP (00-0f-ac:4)
      * CMAC (00-0f-ac:6)
   Available Antennas: TX 0x3 RX 0x3
   Configured Antennas: TX 0x3 RX 0x3
   Supported interface modes:
       * IBSS
       * managed
       * AP
       * AP/VLAN
       * WDS
       * monitor
       * mesh point
       * P2P-client
       * P2P-GO
   software interface modes (can always be added):
       * AP/VLAN
       * monitor
   valid interface combinations:
       * #{ managed, WDS, P2P-client } <= 2048, #{ IBSS, AP, mesh point, P2P-GO } <= 8,
         total <= 2048, #channels <= 1
   Supported commands:
       * new_interface
       * set_interface
       * new_key
       * start_ap
       * new_station
       * new_mpath
       * set_mesh_config
       * set_bss
       * authenticate
       * associate
       * deauthenticate
       * disassociate
       * join_ibss
       * join_mesh
       * remain_on_channel
       * set_tx_bitrate_mask
       * frame
       * frame_wait_cancel
       * set_wiphy_netns
       * set_channel
       * set_wds_peer
       * tdls_mgmt
       * tdls_oper
       * probe_client
       * set_noack_map
       * register_beacons
       * Unknown command (89)
       * connect
       * disconnect
   Supported TX frame types:
       * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
       * (null): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
   Supported RX frame types:
       * IBSS: 0xb0 0xc0 0xd0
       * managed: 0x40 0xd0
       * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
       * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
       * mesh point: 0xb0 0xc0 0xd0
       * P2P-client: 0x40 0xd0
       * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
       * (null): 0x40 0xd0
   Device supports RSN-IBSS.
   HT Capability overrides:
       * MCS: ff ff ff ff ff ff ff ff ff ff
       * maximum A-MSDU length
       * supported channel width
       * short GI for 40 MHz
       * max A-MPDU length exponent
       * min MPDU start spacing
   Device supports TX status socket option.
   Device supports HT-IBSS.


El log del sistema chiva algo, pero no estoy seguro que esté relaccionado:
Citar

dmesg
[    0.000000] Linux version 3.3.8 (hulks@hulks) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Nov 10 01:09:36 CET 2012
[    0.000000] SoC: Danube rev 1.5
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8029d0c0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,jffs2 machtype=ARV7518PW
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=0006f558
[    0.000000] Readback ErrCtl register=0006f558
[    0.000000] Memory: 61860k/65536k available (2278k kernel code, 3676k reserved, 391k data, 172k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 333MHz
[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.048000] NET: Registered protocol family 16
[    0.056000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio
[    0.060000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio
[    0.064000] MIPS: machine is ARV7518PW - ASTORIA
[    0.068000] gpiochip_add: registered GPIOs 100 to 115 on device: ltq_ebu
[    0.112000] bio: create slab <bio-0> at 0
[    0.120000] PCI host bridge to bus 0000:00
[    0.124000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.128000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.132000] pci 0000:00:0e.0: [168c:ff1d] type 0 class 0x000200
[    0.132000] pci 0000:00:0e.0: fixup device configuration
[    0.136000] pci 0000:00:0e.0: fixup info: [168c:0029] revision 01 class 0x028000
[    0.140000] pci 0000:00:0e.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.140000] pci 0000:00:0e.0: PME# supported from D0 D3hot
[    0.140000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.144000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
[    0.148000] Switching to clocksource MIPS
[    0.156000] NET: Registered protocol family 2
[    0.164000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.168000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.176000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.184000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.188000] TCP reno registered
[    0.192000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.200000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.204000] NET: Registered protocol family 1
[    0.208000] PCI: CLS 0 bytes, default 32
[    0.212000] gptu: totally 6 16-bit timers/counters
[    0.216000] gptu: misc_register on minor 63
[    0.220000] gptu: succeeded to request irq 126
[    0.224000] gptu: succeeded to request irq 127
[    0.228000] gptu: succeeded to request irq 128
[    0.232000] gptu: succeeded to request irq 129
[    0.236000] gptu: succeeded to request irq 130
[    0.244000] gptu: succeeded to request irq 131
[    0.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.256000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.268000] msgmni has been set to 120
[    0.272000] io scheduler noop registered
[    0.276000] io scheduler deadline registered (default)
[    0.280000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[    0.288000] console [ttyLTQ1] enabled, bootconsole disabled
[    0.304000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.312000] ltq_nor: Found an alias at 0x800000 for the chip at 0x0
[    0.312000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.316000]   Amd/Fujitsu Extended Query version 1.1.
[    0.320000] number of CFI chips: 1
[    0.324000] Creating 4 MTD partitions on "ltq_nor":
[    0.328000] 0x000000000000-0x000000010000 : "uboot"
[    0.336000] 0x000000010000-0x000000020000 : "uboot_env"
[    0.344000] 0x000000020000-0x0000007f0000 : "linux"
[    0.348000] found squashfs behind kernel
[    0.352000] Creating 2 MTD partitions on "ltq_nor":
[    0.356000] 0x000000020000-0x00000010c336 : "kernel"
[    0.360000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.376000] 0x00000010c336-0x0000007f0000 : "rootfs"
[    0.380000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.396000] mtd: partition "rootfs" set to be root filesystem
[    0.400000] mtd: partition "rootfs_data" created automatically, ofs=610000, len=1E0000
[    0.408000] 0x000000610000-0x0000007f0000 : "rootfs_data"
[    0.416000] 0x0000007f0000-0x000000800000 : "board_config"
[    0.572000] ltq_mii: probed
[    0.596000] eth0: Atheros AR8216 switch driver attached.
[    0.696000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=ltq_etop-fffffff:00, irq=-1)
[    0.708000] Registered led device: soc:red:power
[    0.708000] Registered led device: soc:green:power
[    0.708000] Registered led device: soc:green:wifi
[    0.708000] Registered led device: soc:green:adsl
[    0.712000] Registered led device: soc:green:internet
[    0.712000] Registered led device: soc:red:internet
[    0.712000] Registered led device: soc:green:voip
[    0.712000] Registered led device: soc:green:phone1
[    0.712000] Registered led device: soc:green:phone2
[    0.712000] Registered led device: soc:orange:fail
[    0.716000] Registered led device: soc:green:usb
[    0.716000] Registered led device: soc:orange:wps
[    0.716000] Registered led device: soc:green:wps
[    0.716000] Registered led device: soc:red:wps
[    0.716000] TCP cubic registered
[    0.720000] NET: Registered protocol family 17
[    0.724000] 8021q: 802.1Q VLAN Support v1.8
[    0.740000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.748000] Freeing unused kernel memory: 172k freed
[    7.280000] JFFS2 notice: (432) jffs2_build_xattr_subsystem: complete building xattr subsystem, 25 of xdatum (0 unchecked, 24 orphan) and 31 of xref (0 dead, 24 orphan) found.
[    8.220000] SCSI subsystem initialized
[    8.496000] usbcore: registered new interface driver usbfs
[    8.500000] usbcore: registered new interface driver hub
[    8.512000] usbcore: registered new device driver usb
[    9.420000] dwc_otg: version 2.60a 22-NOV-2006
[   10.024000] DWC_otg: Using DMA mode
[   10.028000] dwc_otg dwc_otg.0: DWC OTG Controller
[   10.032000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[   10.040000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
[   10.048000] DWC_otg: Init: Port Power? op_state=1
[   10.052000] DWC_otg: Init: Power Port (0)
[   10.056000] hub 1-0:1.0: USB hub found
[   10.056000] hub 1-0:1.0: 1 port detected
[   10.204000] DISCONNECTED PORT
[   10.208000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   10.348000] Initializing USB Mass Storage driver...
[   10.352000] usbcore: registered new interface driver usb-storage
[   10.360000] USB Mass Storage support registered.
[   33.380000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[   33.380000]
[   33.412000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   33.420000] Backport based on wireless-testing.git master-2012-09-07
[   33.424000] compat.git: wireless-testing.git
[   33.700000] cfg80211: Calling CRDA to update world regulatory domain
[   33.708000] cfg80211: World regulatory domain updated:
[   33.712000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   33.720000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.728000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   33.736000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   33.744000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.748000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   34.832000] cfg80211: World regulatory domain updated:
[   34.836000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   34.844000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   34.848000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   34.856000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   34.864000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   34.872000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   34.892000] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[   35.636000] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[   35.640000] request_timer(3, 0x000001AE, 1)...successful!
[   35.648000] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[   36.080000] Lantiq KPI2UDP driver, version 2.2.0.0, (c) 2008-2010 Lantiq Deutschland GmbH
[   36.768000] usbcore: registered new interface driver rt73usb
[   36.804000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   36.820000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   36.824000] ath: phy0: random mac address will be used: fa:57:19:4d:65:e7
[   36.832000] ath: EEPROM regdomain: 0x67
[   36.832000] ath: EEPROM indicates we should expect a direct regpair map
[   36.832000] ath: Country alpha2 being used: 00
[   36.832000] ath: Regpair used: 0x67
[   36.840000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   36.840000] Registered led device: ath9k-phy0
[   36.840000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb8000000, irq=30
[   36.888000] NET: Registered protocol family 8
[   36.888000] NET: Registered protocol family 20
[   36.944000] Button Hotplug driver version 0.4.1
[   37.644000] PPP generic driver version 2.4.2
[   38.084000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   38.492000] NET: Registered protocol family 24
[   38.688000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
[   39.988000] xt_time: kernel timezone is -0000
[   40.556000] IFX MEI Version 5.00.00
[   40.692000]
[   40.692000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   40.732000]     ATM (A1) firmware version 1.0.19
[   40.736000] ifxmips_atm: ATM init succeed
[   40.960000] usbcore: registered new interface driver usblp
[   41.132000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[   46.656000] device eth0.1 entered promiscuous mode
[   46.656000] device eth0 entered promiscuous mode
[   46.656000] br-lan: port 1(eth0.1) entered forwarding state
[   46.656000] br-lan: port 1(eth0.1) entered forwarding state
[   48.660000] br-lan: port 1(eth0.1) entered forwarding state
[   49.084000] cfg80211: Calling CRDA for country: ES
[   49.084000] cfg80211: Regulatory domain changed to country: ES
[   49.084000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   49.084000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   49.084000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   49.084000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   49.084000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   53.092000] device wlan0 entered promiscuous mode
[   54.504000] br-lan: port 2(wlan0) entered forwarding state
[   54.504000] br-lan: port 2(wlan0) entered forwarding state

En concreto la parte de   
Citar

36.820000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   36.824000] ath: phy0: random mac address will be used: fa:57:19:4d:65:e7
[   36.832000] ath: EEPROM regdomain: 0x67
[   36.832000] ath: EEPROM indicates we should expect a direct regpair map
[   36.832000] ath: Country alpha2 being used: 00
[   36.832000] ath: Regpair used: 0x67


En la rama de ar7 han sacado parches para este error, no se si solucionan este problema o no.

Un saludo a todos
Pteridium:
Cita de: g2rp en 13-11-2012, 23:18 (Martes)

Buenas, estoy probando la beta 2 en un arv7518 y me pasa como a brunorro, no me deja subir el txpower de 3dbm, ni con iwconfig ni nada, por lo que el rango es bastante limitado.

He probado compilando con la opción del kernel, Kernel Modules → Wireless Drivers → kmod-ath → Configuration → Force Atheros drivers to respect the user's regdomain settings = YES, y deja cambiar de regdomain sin problemas (activa el canal 14 por ejemplo si lo pones en Japon) pero el txpower nada.

Haciendo iw list: Citar

iw list
Wiphy phy0
   Band 1:
      Capabilities: 0x11ce
         HT20/HT40
         SM Power Save disabled
         RX HT40 SGI
         TX STBC
         RX STBC 1-stream
         Max AMSDU length: 3839 bytes
         DSSS/CCK HT40
      Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
      Minimum RX AMPDU time spacing: 8 usec (0x06)
      HT TX/RX MCS rate indexes supported: 0-15
      Frequencies:
         * 2412 MHz [1] (3.0 dBm)
         * 2417 MHz [2] (3.0 dBm)
         * 2422 MHz [3] (3.0 dBm)
         * 2427 MHz [4] (3.0 dBm)
         * 2432 MHz [5] (3.0 dBm)
         * 2437 MHz [6] (3.0 dBm)
         * 2442 MHz [7] (3.0 dBm)
         * 2447 MHz [8] (3.0 dBm)
         * 2452 MHz [9] (3.0 dBm)
         * 2457 MHz [10] (3.0 dBm)
         * 2462 MHz [11] (3.0 dBm)
         * 2467 MHz [12] (3.0 dBm)
         * 2472 MHz [13] (3.0 dBm)
         * 2484 MHz [14] (disabled)


El log del sistema chiva algo, pero no estoy seguro que esté relaccionado:

En concreto la parte de    
Citar

36.820000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   36.824000] ath: phy0: random mac address will be used: fa:57:19:4d:65:e7
[   36.832000] ath: EEPROM regdomain: 0x67
[   36.832000] ath: EEPROM indicates we should expect a direct regpair map
[   36.832000] ath: Country alpha2 being used: 00
[   36.832000] ath: Regpair used: 0x67


En la rama de ar7 han sacado parches para este error, no se si solucionan este problema o no.

Un saludo a todos


Supongo que con ar7 te referirás al target Atheros ar71xx. La wifi en ese target comparte muchas cosas con los drivers ath5k y ath9k, pero este fallo, junto con el del arv4518 parece que son exclusivos de estos modelos: la wifi se ha implementado pero después de eso apenas se ha tocado nada. Creo que han tenido algo más de suerte los modelos que tienen wifi Ralink, pero no estoy seguro.

Aquí tenemos un maravilloso ejemplo de un ticket al que nadie le ha hecho caso:
https://dev.openwrt.org/ticket/11704
De todas formas quizá sea bueno que se abra uno para el problema que tiene el 7518 con la MAC wireless y txpower. Además parece que hay que avisar expresamente a blogic, o por lo menos es lo que entiendo en la parte final de este otro ticket:
https://dev.openwrt.org/ticket/9388

Os pido que alguien que sepa de estos detalles de mailing list se lo deje caer a blogic, que estas cosillas ya me superan un poco, y además él es un poco quisquilloso.   >:D

Edito:
Me encontré esto en el foro de OpenWRT, pero hoy no tengo la cabeza para muchas historias. Por lo que pude leer por encima es un script para cambiar u-boot sin entrar en modo uart siempre y cuando se pueda acceder al u-boot que está grabado por puerto serie.
https://forum.openwrt.org/viewtopic.php?pid=183315#p183315
Pteridium:
Cita de: jar229 en 07-11-2012, 20:31 (Mircoles)

El tema de los botones, a ver si te vale esto que comentó Noltari: http://foro.seguridadwireless.net/openwrt/openwrt-en-huaweig-hg556a/msg254701/#msg254701

Es probable que en tu router sea diferente, pero igual te da alguna pista  ;)


Me ha servido un montón, muchísimas gracias a Noltari por el post y a ti por poner el enlace, que fijo que no debió ser fácil encontrarlo.  >:( >:( >:(

De momento estoy practicando lo de los botones con un Comtrend porque es más fácil, pero en cuanto le coja ritmo ya me pongo para hacerlo con los de yacom, aunque si alguien lo consigue antes mejor para todos.
Spinete:
Hola a todos,

Estoy interesado en ponerle OpenWRT a uno de mis routers viejos de Ya.com (el de color gris), un Arcadyan ARV4518PW (SMC-7908-ISP).

He visto en el primero post del hilo y en la wiki de OpenWRT (http://wiki.openwrt.org/toh/arcadyan/arv4518pw) que para esta versión de router la wifi no funciona. Sin embargo, mirando por ahí he visto que en la página oficial del proyecto Linux Wireless comentan que el driver ath5k tiene soporte para el Atheros AR2417. La información que he encontrado es la siguiente:

http://wireless.kernel.org/en/users/Drivers/ath5k#Supported_PCI_IDs
Supported PCI IDs

Currently supported PCI ID list with respective status report on basic-testing as defined above.

Vendor:device   Type    Name     Basic-testing
168c:0207       AR5210  AR5210   No tx - working on it
168c:0007       <<      <<       No tx - working on it

168c:0011       AR5211  AR5211   Should work
168c:0012       <<      <<       OK

168c:0013       AR5212  AR521/3 OK
a727:0013       <<      <<       Should Work
10b7:0013       <<      <<       <<
168c:0014       <<      <<       <<
168c:0015       <<      <<       <<
168c:0016       <<      <<       <<
168c:0017       <<      <<       <<
168c:0018       <<      <<       <<
168c:0019       <<      <<       <<
168c:001a       <<      AR2413/4 OK
168c:001b       <<      AR5413/4 OK
168c:001c       <<      Condor   OK (*)
168c:001d       <<      AR2417   OK
Notes on supported devices

"OK" means that card operates as good as with binary drivers.

"Should work" means that card hasn't been tested (we haven't received any reports) but since chipset is the same with a tested, working card, it should work as well.

(*) 001c is used also for AR2425 parts.


Fijaros que el AR2417 sale en la lista como soportado por el driver ath5k. He estado mirando en el trunk de OpenWRT y este driver junto con el convencional ath y el ath9k estan integrados en el repositorio.

¿Alguien me puede decir porque estando soportado por el ath5k existen problemas con este dispositivo?

Muchas gracias
Saludos!
yorse:
Buenas.
Después de dos semanas esperando ya tengo el     
CABLE CONVERTIDOR USB 2.0 TO RS232 UART TTL y me dispongo a poner openWRT en mi astoria arv7518.

Pues mi primer problema viene cuando lo conecto al serial que segun el manual deberia aparecer el menu

Citar

ROM VER: 1.0.3
CFG 01
Readà
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X

=======================================================================
Wireless ADSL Gateway DANUBE Loader 64M-V0.02 build Apr 24 2008 16:12:25
Arcadyan Technology Corporation
=======================================================================
MXIC MX29LV320ABTC bottom boot 16-bit mode found

Copying boot params.....DONE

Press Space Bar 3 times to enter command mode ...

pero no, a mi me salen mensajes de que el router esta iniciandose... como esto
Citar

###ming###: tell 802.1x module to add a client entry for this STA,

dot1x_handle_new_assoc enter dot1x_ifno:0...

dot1x_handle_new_assoc enter 2...

ieee80211_iserp_rateset : 2 4 11 12 18 22 24 36 48 72 96 108

[dot1x] : func handle_traps   <======================

64:70:02:19:aa:a7 assoc req from ifno:2

config->enableSSN:3

[dot1x] : func blob_portstatus_set   <---------------------

[dot1x] : func blob_clr_persta_key   <---------------------

blob_clr_persta_key : ifno 2

###ming###: tell 802.1x module to add a client entry for this STA,

dot1x_handle_new_assoc enter dot1x_ifno:0...

dot1x_handle_new_assoc enter 2...

ieee80211_iserp_rateset : 2 4 11 12 18 22 24 36 48 72 96 108

[dot1x] : func handle_traps   <======================

64:70:02:19:aa:a7 assoc req from ifno:2

config->enableSSN:3

[dot1x] : func blob_portstatus_set   <---------------------

[dot1x] : func blob_clr_persta_key   <---------------------

blob_clr_persta_key : ifno 2

###ming###: tell 802.1x module to add a client entry for this STA,


Asi hasta que queda intentando conectar con las dns de ya.com.

¿Es que tengo que hacer algo antes?
A ver si podéis echarme un cable en configurar mis routers. Que tengo dos y me gustaría darles uso.


Gracias
Navegación
Índice de Mensajes
Página Siguiente
Página Anterior